| Age | Commit message (Collapse) | Author |
|---|
|
Replace 'decided' with 'decide' so that comment would be
/* To decide when the network namespace should be freed. */
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg:
====================
Here are a few groups of changes:
* EDMG channel support (60 GHz, just a single patch)
* initial 6/7 GHz band support (Arend)
* association timestamp recording (Ben)
* rate control improvements for better performance with
the mt76 driver (Felix)
* various fixes for previous HE support changes (John)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three fixes:
* extended key ID key installation
* regulatory processing
* possible memory leak in an error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
mlxsw: Add devlink-trap support
This patchset adds devlink-trap support in mlxsw.
Patches #1-#4 add the necessary APIs and defines in mlxsw.
Patch #5 implements devlink-trap support for layer 2 drops. More drops
will be added in the future.
Patches #6-#7 add selftests to make sure that all the new code paths are
exercised and that the feature is working as expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test generic devlink-trap functionality over mlxsw. These tests are not
specific to a single trap, but do not check the devlink-trap common
infrastructure either.
Currently, the only test case is device deletion (by reloading the
driver) while packets are being trapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register supported packet traps (layer 2 drops only, currently) and
associated trap group with devlink during driver initialization.
The amount of traffic generated by these packet drop traps is capped at
10Kpps to ensure the CPU is not overwhelmed by incoming packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Discard trap groups are defined in a different enum so that they could
all share the same policer ID: MLXSW_REG_HTGT_TRAP_GROUP_MAX + 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the trap IDs used to report layer 2 drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Subsequent patches will add discard traps support in mlxsw. The driver
cannot configure such traps with a normal trap action, but needs to use
exception trap action, which also increments an error counter.
On the other hand, when these traps are initialized or set to drop
action, they should use the default drop action set by the firmware.
This guarantees that when the feature is disabled we get the exact same
behavior as before the feature was introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now the action of a trap was never changed during its lifetime.
This is going to change by subsequent patches that will allow devlink to
control the action of certain traps.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new subcommand to freeze maps from user space.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When listing maps, read their "frozen" status from procfs, and tell if
maps are frozen.
As commit log for map freezing command mentions that the feature might
be extended with flags (e.g. for write-only instead of read-only) in the
future, use an integer and not a boolean for JSON output.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pull KVM fixes from Paolo Bonzini:
"A couple bugfixes, and mostly selftests changes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
selftests/kvm: make platform_info_test pass on AMD
Revert "KVM: x86/mmu: Zap only the relevant pages when removing a memslot"
selftests: kvm: fix state save/load on processors without XSAVE
selftests: kvm: fix vmx_set_nested_state_test
selftests: kvm: provide common function to enable eVMCS
selftests: kvm: do not try running the VM in vmx_set_nested_state_test
KVM: x86: svm: remove redundant assignment of var new_entry
MAINTAINERS: add KVM x86 reviewers
MAINTAINERS: change list for KVM/s390
kvm: x86: skip populating logical dest map if apic is not sw enabled
|
|
I forgot to release the allocated object at the early error path in
line6_init_pcm(). For addressing it, slightly shuffle the code so
that the PCM destructor (pcm->private_free) is assigned properly
before all error paths.
Fixes: 3450121997ce ("ALSA: line6: Fix write on zero-sized buffer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix a 'struct pt_reg' typo and clarify when bpf_trace_printk discards
lines. Affects documentation only.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
I opened /sys/kernel/tracing/trace once and kept reading from it.
bpf_trace_printk somehow did not seem to work, no entries were appended
to that trace file. It turns out that tracing is disabled when that file
is open. Save the next person some time and document this.
The trace file is described in Documentation/trace/ftrace.rst, however
the implication "tracing is disabled" did not immediate translate to
"bpf_trace_printk silently discards entries".
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
There is no 'struct pt_reg'.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
PERF_EVENT_IOC_SET_BPF supports uprobes since v4.3, and tracepoints
since v4.7 via commit 04a22fae4cbc ("tracing, perf: Implement BPF
programs attached to uprobes"), and commit 98b5c2c65c29 ("perf, bpf:
allow bpf programs attach to tracepoints") respectively.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
test_msr_platform_info_disabled() generates EXIT_SHUTDOWN but VMCB state
is undefined after that so an attempt to launch this guest again from
test_msr_platform_info_enabled() fails. Reorder the tests to make test
pass.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Pull nfsd fixes from Bruce Fields:
"Fix nfsd bugs: three in the new nfsd/clients/ code, one in the reply
cache containerization"
* tag 'nfsd-5.3-1' of git://linux-nfs.org/~bfields/linux:
nfsd4: Fix kernel crash when reading proc file reply_cache_stats
nfsd: initialize i_private before d_add
nfsd: use i_wrlock instead of rcu for nfsdfs i_private
nfsd: fix dentry leak upon mkdir failure.
|
|
Revision 0x0117 suffers from an identical issue to earlier revisions,
therefore it should be added to the quirks list.
Signed-off-by: Henk van der Laan <opensource@henkvdlaan.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190816200847.21366-1-opensource@henkvdlaan.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After _gadget_stop_activity is executed, we can consider the hardware
operation for gadget has finished, and the udc can be stopped and enter
low power mode. So, any later hardware operations (from usb_ep_ops APIs
or usb_gadget_ops APIs) should be considered invalid, any deinitializatons
has been covered at _gadget_stop_activity.
I meet this problem when I plug out usb cable from PC using mass_storage
gadget, my callstack like: vbus interrupt->.vbus_session->
composite_disconnect ->pm_runtime_put_sync(&_gadget->dev),
the composite_disconnect will call fsg_disable, but fsg_disable calls
usb_ep_disable using async way, there are register accesses for
usb_ep_disable. So sometimes, I get system hang due to visit register
without clock, sometimes not.
The Linux Kernel USB maintainer Alan Stern suggests this kinds of solution.
See: http://marc.info/?l=linux-usb&m=138541769810983&w=2.
Cc: <stable@vger.kernel.org> #v4.9+
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20190820020503.27080-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A malicious device can make the driver divide ny zero
with a nonsense maximum packet size.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190820092826.17694-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Silence the following fall-through warning by adding a break statement:
drivers/usb/gadget/udc/lpc32xx_udc.c:2230:3: warning: this statement may
fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190821021627.GA2679@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If rs_prepare_reshape() fails, no cleanup is executed, leading to
leak of the raid_set structure allocated at the beginning of
raid_ctr(). To fix this issue, go to the label 'bad' if the error
occurs.
Fixes: 11e4723206683 ("dm raid: stop keeping raid set frozen altogether")
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
This function is supposed to return error pointers so it matches the
dmz_get_rnd_zone_for_reclaim() function. The current code could lead to
a NULL dereference in dmz_do_reclaim()
Fixes: b234c6d7a703 ("dm zoned: improve error handling in reclaim")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Change the "frontend" dust_remove_block, dust_add_block, and
dust_query_block functions to store the "dust block number", instead
of the sector number corresponding to the "dust block number".
For the "backend" functions dust_map_read and dust_map_write,
right-shift by sect_per_block_shift. This fixes the inability to
emulate failure beyond the first sector of each "dust block" (for
devices with a "dust block size" larger than 512 bytes).
Fixes: e4f3fabd67480bf ("dm: add dust target")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan Gurney <bgurney@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When ./test_xdp_vlan_mode_generic.sh runs it complains that it can't
find file test_xdp_vlan.sh.
# selftests: bpf: test_xdp_vlan_mode_generic.sh
# ./test_xdp_vlan_mode_generic.sh: line 9: ./test_xdp_vlan.sh: No such
file or directory
Rework so that test_xdp_vlan.sh gets installed, added to the variable
TEST_PROGS_EXTENDED.
Fixes: d35661fcf95d ("selftests/bpf: add wrapper scripts for test_xdp_vlan.sh")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Jesper Dangaard Brouer <jbrouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When running test_kmod.sh the following shows up
# sysctl cannot stat /proc/sys/net/core/bpf_jit_enable No such file or directory
cannot: stat_/proc/sys/net/core/bpf_jit_enable #
# sysctl cannot stat /proc/sys/net/core/bpf_jit_harden No such file or directory
cannot: stat_/proc/sys/net/core/bpf_jit_harden #
Rework to enable CONFIG_BPF_JIT to solve "No such file or directory"
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
test_btf_dump fails when run with O=, because it needs to access source
files and assumes they live in ./progs/, which is not the case in this
scenario.
Fix by instructing kselftest to copy btf_dump_test_case_*.c files to the
test directory. Since kselftest does not preserve directory structure,
adjust the test to look in ./progs/ and then in ./.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
test_cgroup_storage fails on s390 with an assertion failure: packets are
dropped when they shouldn't. The problem is that BPF_DW packet count is
accessed as BPF_W with an offset of 0, which is not correct on
big-endian machines.
Since the point of this test is not to verify narrow loads/stores,
simply use BPF_DW when working with packet counts.
Fixes: 68cfa3ac6b8d ("selftests/bpf: add a cgroup storage test")
Fixes: 919646d2a3a9 ("selftests/bpf: extend the storage test to test per-cpu cgroup storage")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Use different namespaces for bypass and switchdev loopback because they
have different priorities and default table miss action requirement:
1. bypass: with multiple priorities support, and
MLX5_FLOW_TABLE_MISS_ACTION_DEF as the default table miss action;
2. switchdev loopback: with single priority support, and
MLX5_FLOW_TABLE_MISS_ACTION_SWITCH_DOMAIN as the default table miss
action.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Currently all the namespaces under the same steering domain share the same
default table miss action, however in some situations (e.g., RDMA RX)
different actions are required. This patch adds a per-namespace default
table miss action instead of using the miss action of the steering domain.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Building s390 kernel with CONFIG_DEBUG_INFO_BTF fails, because
CONFIG_OUTPUT_FORMAT is not defined. As a matter of fact, this variable
appears to be x86-only, so other arches might be affected as well.
Fix by obtaining this value from objdump output, just like it's already
done for bin_arch. The exact objdump invocation is "inspired" by
arch/powerpc/boot/wrapper.
Also, use LANG=C for the existing bin_arch objdump invocation to avoid
potential build issues on systems with non-English locale.
Fixes: 341dfcf8d78e ("btf: expose BTF info through sysfs")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The WRITE_PROTECT bit is always in a "protected mode" on Tegra and
WP-GPIO state need to be used instead. In a case of the GPIO absence,
write-enable should be assumed. External SD is writable once again as
a result of this patch because the offending commit changed behaviour for
the case of a missing WP-GPIO to fall back to WRITE_PROTECT bit-checking,
which is incorrect for Tegra.
Cc: stable@vger.kernel.org # v5.1+
Fixes: e8391453e27f ("mmc: sdhci-tegra: drop ->get_ro() implementation")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For arm32 xdp sockets mmap2 is preferred, so use it if it's defined.
Declaration of __NR_mmap can be skipped and it breaks build.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
For 64-bit there is no reason to use vmap/vunmap, so use page_address
as it was initially. For 32 bits, in some apps, like in samples
xdpsock_user.c when number of pgs in use is quite big, the kmap
memory can be not enough, despite on this, kmap looks like is
deprecated in such cases as it can block and should be used rather
for dynamic mm.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Drop __NR_mmap2 fork in flavor of LFS, that is _FILE_OFFSET_BITS=64
(glibc & bionic) / LARGEFILE64_SOURCE (for musl) decision. It allows
mmap() to use 64bit offset that is passed to mmap2 syscall. As result
pgoff is not truncated and no need to use direct access to mmap2 for
32 bits systems.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The conversion during HDMI HW readout from port_clock to crtc_clock was
missed when HDMI 10bpc support was added, so fix that.
v2:
- Unscrew the non-HDMI case.
Fixes: cd9e11a8bf25 ("drm/i915/icl: Add 10-bit support for hdmi")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109593
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808162547.7009-1-imre.deak@intel.com
(cherry picked from commit 2969a78aead38b49e80c821a5c683544ab16160d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
On some devices that only support static rate fallback tables sending rate
control probing packets can be really expensive.
Probing lower rates can already hurt throughput quite a bit. What hurts even
more is the fact that on mt76x0/mt76x2, single probing packets can only be
forced by directing packets at a different internal hardware queue, which
causes some heavy reordering and extra latency.
The reordering issue is mainly problematic while pushing lots of packets to
a particular station. If there is little activity, the overhead of probing is
neglegible.
The static fallback behavior is designed to pretty much only handle rate
control algorithms that use only a very limited set of rates on which the
algorithm switches up/down based on packet error rate.
In order to better support that kind of hardware, this patch implements a
different approach to rate probing where it switches to a slightly higher rate,
waits for tx status feedback, then updates the stats and switches back to
the new max throughput rate. This only triggers above a packet rate of 100
per stats interval (~50ms).
For that kind of probing, the code has to reduce the set of probing rates
a lot more compared to single packet probing, so it uses only one packet
per MCS group which is either slightly faster, or as close as possible to
the max throughput rate.
This allows switching between similar rates with different numbers of
streams. The algorithm assumes that the hardware will work its way lower
within an MCS group in case of retransmissions, so that lower rates don't
have to be probed by the high packets per second rate probing code.
To further reduce the search space, it also does not probe rates with lower
channel bandwidth than the max throughput rate.
At the moment, these changes will only affect mt76x0/mt76x2.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use the first supported rate instead of 0 (which can be invalid)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On hardware with static fallback tables (e.g. mt76x2), rate probing attempts
can be very expensive.
On such devices, avoid sampling rates slower than the per-group max throughput
rate, based on the assumption that the fallback table will take care of probing
lower rates within that group if the higher rates fail.
To further reduce unnecessary probing attempts, skip duplicate attempts on
rates slower than the max throughput rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The group number needs to be multiplied by the number of rates per group
to get the full rate index
Fixes: 5935839ad735 ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
he_spr_ie_elem is dereferenced before the NULL check. fix this by moving
the assignment after the check.
fixes commit 697f6c507c74 ("mac80211: propagate HE operation info into
bss_conf")
This was reported by the static code checker.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190813070712.25509-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Report timestamp for when sta becomes associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-2-greearb@candelatech.com
[fix ktime_get_boot_ns() to ktime_get_boottime_ns(), assoc_at type to u64]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Report timestamp of when sta became associated.
This is the boottime clock, units are nano-seconds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For the new 6GHz band the same rules apply for mandatory rates so
add it to set_mandatory_flags_band() function.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-9-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The default mandatory rates, ie. when not specified by user-space, is
determined by the band. Select 11a rateset for 6GHz band.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-8-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
