| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
|
|
Secondary unicast MAC addresses will get deleted only when the interface is UP.
When the interface is DOWN, though these secondary MAC addresses are unusable
and awaiting to be deleted, cause the firmware to believe that they are being used.
If the user intends to set a MAC address as primary MAC from one of these
secondary MAC addresses, the firmware returns a MAC address Collision error.
Delete these secondary MAC addresses during be_close.
The secondary MAC addresses list will be refreshed during interface open anyway.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently requests the firmware to enable rx_interface options
without considering if the interface was created with that capability.
This could cause commands to firmware to fail.
To avoid this, enable only those options on an interface if the interface
was created with that capability.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is more appropriate to use # of queue pairs currently used by
the driver instead of a magic value.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A plain read() on a socket does set msg->msg_name to NULL. So check for
NULL pointer first.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yuval Mintz says:
====================
bnx2x: Bug fixes patch series
This series contains several fixes, relating either to SR-IOV flows
or to critical sections protected by the rtnl lock.
Please consider applying these patches to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current driver release rtnl lock in between DCB re-configuration.
As a result, other flows (e.g., mtu config) may enter in between and fail
due to halted tx path for dcb configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During VF load, prior to sending messages on HW channel to PF the VF
checks its bulletin board to see whether the PF indicated it has closed;
If a closed PF is encountered, the VF skips sending the message.
Due to incorrect return values, there's a possible scenario in which the VF
finishes loading "successfully", while the PF hasn't actually fully configured
FW/HW for the VFs supposed configuration.
Once VF tries to send Tx packets, HW will raise an attention (and FW possibly
will start treat the VF as malicious).
The patch fails the loading process in such a scenario.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If chip enters a recovery flow just after the driver issues a DMAE request
the DMAE will timeout. Current code will cause a bnx2x_panic() as a result,
which means interface will no longer be usable (regardless of the recovery
results), as bnx2x_panic() is irreversible for the driver.
As this is a possible flow, the panic should be reached only when driver
is compiled with STOP_ON_ERROR.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While unloading, bnx2x needs to clean the sp_rtnl_state to prevent
configuration made before the unload to be applied afterwards with
stale values.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6d0bfe22611602f36617bc7aa2ffa1bbb2f54c67
net: ipv6: Add IPv6 support to the ping socket
introduced a change in the cleanup logic of inet6_init and
has a bug in that ipv6_packet_cleanup() may not be called.
Fix the cleanup ordering.
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Lorenzo Colitti <lorenzo@google.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use helper functions named similar to other drivers to access
superio registers.
Request memory region only when needed, and use request_muxed_region().
This lets other devices (hwmon, gpio) use the same region.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
There is no need to enable the watchdog device if it is already enabled.
Also, when enabling the watchdog device, only set the watchdog device
enable bit and do not touch other bits; depending on the chip type,
those bits may enable other functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
It is unnecessary to enable the logical device and WDT0 each time
the watchdog is accessed. Do it only once during initialization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Sparse pointed out that the new flags variable I had added
shadowed an existing one, rename the new one to avoid that,
making the code clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free temporary 'chanspecs' avoiding leakage.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Only update *addr_len when we actually fill in sockaddr, otherwise we
can return uninitialized memory from the stack to the caller in the
recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL)
checks because we only get called with a valid addr_len pointer either
from sock_common_recvmsg or inet_recvmsg.
If a blocking read waits on a socket which is concurrently shut down we
now return zero and set msg_msgnamelen to 0.
Reported-by: mpb <mpb.mail@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_SYSCTL=n the following build warning happens:
net/ipv6/ndisc.c:1730:1: warning: label 'out' defined but not used [-Wunused-label]
The 'out' label is only used when CONFIG_SYSCTL=y, so move it inside the
'ifdef CONFIG_SYSCTL' block.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the bus speed parse
error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There was a bug in xennet_alloc_rx_buffers, when allocating page or
sk_buff failed, and at the same time rx_batch queue not empty,
the rx_refill_timer timer won't be scheduled. If finally the remaining
request buffers in rx ring less than what backend driver expected,
the backend driver would think of rx ring as full and start dropping packets.
In such situation, there is no way for the netfront driver to recover
automatically, so that the device can not work properly.
The patch fixes the problem by always scheduling rx_refill_timer timer when
alloc_page or __netdev_alloc_skb fails, no matter whether rx_batch queue is
empty or not. It ensures that the rx ring request buffers will finally meet
the backend needs.
Signed-off-by: Ma JieYue <jieyue.majy@alibaba-inc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nf_conntrack_free() decrements our counter (net->ct.count)
before releasing the conntrack object. That counter is used in the
nf_conntrack_cleanup_net_list path to check if it's time to
kmem_cache_destroy our cache of conntrack objects. I think we have
a race there that should be easier to trigger (although still hard)
with CONFIG_DEBUG_OBJECTS_FREE as object releases become slowier
according to the following splat:
[ 1136.321305] WARNING: CPU: 2 PID: 2483 at lib/debugobjects.c:260
debug_print_object+0x83/0xa0()
[ 1136.321311] ODEBUG: free active (active state 0) object type:
timer_list hint: delayed_work_timer_fn+0x0/0x20
...
[ 1136.321390] Call Trace:
[ 1136.321398] [<ffffffff8160d4a2>] dump_stack+0x45/0x56
[ 1136.321405] [<ffffffff810514e8>] warn_slowpath_common+0x78/0xa0
[ 1136.321410] [<ffffffff81051557>] warn_slowpath_fmt+0x47/0x50
[ 1136.321414] [<ffffffff812f8883>] debug_print_object+0x83/0xa0
[ 1136.321420] [<ffffffff8106aa90>] ? execute_in_process_context+0x90/0x90
[ 1136.321424] [<ffffffff812f99fb>] debug_check_no_obj_freed+0x20b/0x250
[ 1136.321429] [<ffffffff8112e7f2>] ? kmem_cache_destroy+0x92/0x100
[ 1136.321433] [<ffffffff8115d945>] kmem_cache_free+0x125/0x210
[ 1136.321436] [<ffffffff8112e7f2>] kmem_cache_destroy+0x92/0x100
[ 1136.321443] [<ffffffffa046b806>] nf_conntrack_cleanup_net_list+0x126/0x160 [nf_conntrack]
[ 1136.321449] [<ffffffffa046c43d>] nf_conntrack_pernet_exit+0x6d/0x80 [nf_conntrack]
[ 1136.321453] [<ffffffff81511cc3>] ops_exit_list.isra.3+0x53/0x60
[ 1136.321457] [<ffffffff815124f0>] cleanup_net+0x100/0x1b0
[ 1136.321460] [<ffffffff8106b31e>] process_one_work+0x18e/0x430
[ 1136.321463] [<ffffffff8106bf49>] worker_thread+0x119/0x390
[ 1136.321467] [<ffffffff8106be30>] ? manage_workers.isra.23+0x2a0/0x2a0
[ 1136.321470] [<ffffffff8107210b>] kthread+0xbb/0xc0
[ 1136.321472] [<ffffffff81072050>] ? kthread_create_on_node+0x110/0x110
[ 1136.321477] [<ffffffff8161b8fc>] ret_from_fork+0x7c/0xb0
[ 1136.321479] [<ffffffff81072050>] ? kthread_create_on_node+0x110/0x110
[ 1136.321481] ---[ end trace 25f53c192da70825 ]---
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The patch 0ca743a55991: "netfilter: nf_tables: add compatibility
layer for x_tables", leads to the following Smatch
warning: "net/netfilter/nft_compat.c:140 nft_parse_compat()
warn: signedness bug returning '(-34)'"
This nft_parse_compat function returns error codes but the return
type is u8 so the error codes are transformed into small positive
values. The callers don't check the return.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In commit 41d73ec053d2, sequence number adjustments were moved to a
separate file. Unfortunately, the sequence numbers that are stored
in the nf_ct_seqadj structure are expressed in host byte order. The
necessary ntohl call was removed when the call to adjust_tcp_sequence
was collapsed into nf_ct_seqadj_set. This broke the FTP NAT helper.
Fix it by adding back the byte order conversions.
Reported-by: Dawid Stawiarski <dawid.stawiarski@netart.pl>
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Timestamp are used to store additional syncookie parameters such as sack,
ecn, and wscale. The wscale value we need to encode is the client's
wscale, since we can't recover that later in the session. Next overwrite
the wscale option so the later synproxy_send_client_synack will send
the backend's wscale to the client.
Signed-off-by: Martin Topholm <mph@one.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When the synproxy_parse_options is called on the client ack the mss
option will not be present. Consequently mss wont be included in the
backend syn packet, which falls back to 536 bytes mss.
Therefore XT_SYNPROXY_OPT_MSS is explicitly flagged when recovering mss
value from cookie.
Signed-off-by: Martin Topholm <mph@one.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This reverts commit 69f0554ec261fd686ac7fa1c598cc9eb27b83a80.
This patch breaks randconfig on at least the x86-64 architecture, and
most likely on others. There is work underway to support uncompressed
kernels in a generic way, but it looks like it will amount to
rewriting the support from scratch; see the LKML thread in the Link:
for info.
Therefore, revert this change and wait for the fix.
Reported-by: Pavel Roskin <proski@gnu.org>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131113113418.167b8ffd@IRBT4585
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove mpc85xx_pci_err_remove(...) which is obsolete, this removes the
compiler warning which can be seen when building the driver either
statically or as a module.
Signed-off-by: Johannes Thumshirn <morbidrsa@gmail.com>
Link: https://lkml.kernel.org/r/20131112161901.GA15637@jtlinux
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Add drivers/edac/mpc85xx_edac.[ch] to MAINTAINERS file and me as
maintainer.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Link: https://lkml.kernel.org/r/20131112161901.GA15637@jtlinux
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Dave Jiang <dave.jiang@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
As CSR SiRF is converted to multi platform CLOCK_TICK_RATE is a dummy
value that seems to match the right value is used.
(arch/arm/mach-prima2/include/mach/timex.h which defined CLOCK_TICK_RATE
to 1000000 was removed in commit cf82e0e (ARM: sirf: enable
multiplatform support); marco used the same file.)
To not depend on that dummy value use a local #define instead.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
We changed "buf" from being an array of 6 chars to being a pointer this
sizeof(buf) needs to be updated as well.
Fixes: 2ddb8089a7e5 ('watchdog: pcwd_usb: Use allocated buffer for usb_control_msg')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
In case of error, the function devm_request_and_ioremap() returns NULL
pointer not ERR_PTR(). Fix it by using devm_ioremap_resource() instead
of devm_request_and_ioremap().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Fixed a trivial typo.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add device tree support to the DW watchdog timer.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
|
|
I just can't find any value in MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR)
and MODULE_ALIAS_MISCDEV(TEMP_MINOR) statements.
Either the device is enumerated and the driver already has a module
alias (e.g. PCI, USB etc.) that will get the right driver loaded
automatically.
Or the device is not enumerated and loading its driver will lead to
more or less intrusive hardware poking. Such hardware poking should be
limited to a bare minimum, so the user should really decide which
drivers should be tried and in what order. Trying them all in
arbitrary order can't do any good.
On top of that, loading that many drivers at once bloats the kernel
log. Also many drivers will stay loaded afterward, bloating the output
of "lsmod" and wasting memory. Some modules (cs5535_mfgpt which gets
loaded as a dependency) can't even be unloaded!
If defining char-major-10-130 is needed then it should happen in
user-space.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Jim Cromie <jim.cromie@gmail.com>
|
|
timeout_to_regval() returns a valid error code. Might as well use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
usb_control_msg() must use a dma-capable buffer.
This fixes the following error reported by smatch:
drivers/watchdog/pcwd_usb.c:257 usb_pcwd_send_command() error: doing dma on the
stack (buf)
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d0631001288a5974afc0b2a5f568bcdecb4d)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
On CSR SiRFprimaII and SiRFatlasVI, the 6th timer can act as a watchdog
timer when the Watchdog mode is enabled.
watchdog occur when TIMER watchdog counter matches the value software
pre-set, when this event occurs, the effect is the same as the system
software reset.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
of_match_ptr() is a macro used to avoid undefined reference error if
CONFIG_OF is used to selectively compile in or out the
data structure. It is defined as follows:
#ifdef CONFIG_OF
#define of_match_ptr(ptr) ptr
#else
#define of_match_ptr(ptr) NULL
#endif
In the case of this series, none of the drivers use CONFIG_OF macro to
compile out the data structure (i.e., the data structure is always
defined).
Hence the use of of_match_ptr() does not make any sense. Thus removing
it to make the code look simpler for readability.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
There seems to be some confusion here which functions return positive
numbers and which return negative error codes.
copy_to_user() returns the number of bytes remaining to be copied but we
want to return -EFAULT.
The rest is just clean up. get_user() actually returns zero on success
and -EFAULT on error so we can preserve the error code. The
timeout_to_regval() function returns -EINVAL on failure, but we can
propogate that back instead of hardcoding -EINVAL ourselves.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
--
|
|
I accidently put the devicetree bindings for the MEN A21 watchdog driver in
Documentation/devicetree/bindings/gpio instead of
Documentation/devicetree/bindings/watchdog, this patch addresses this error.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Rob Landley <rob@landley.net>
|
|
Add a driver for the watchdog timer found on Ralink SoC
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
|
|
This patch adds a watchdog driver for the main hardware watchdog timer
found on MOXA ART SoCs.
The MOXA ART SoC provides one writable timer register, restarting
the hardware once it reaches zero. The register is auto decremented
every APB clock cycle.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Added __user annotation to fix the following sparse warnings.
Also, it makes 'kempld_prescaler' static because it is used
only in this file.
drivers/watchdog/kempld_wdt.c:70:11: warning: symbol 'kempld_prescaler' was not declared. Should it be static?
drivers/watchdog/kempld_wdt.c:364:23: warning: incorrect type in initializer (different address spaces)
drivers/watchdog/kempld_wdt.c:364:23: expected int const [noderef] <asn:1>*register __p
drivers/watchdog/kempld_wdt.c:364:23: got int *<noident>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Added __user annotation to fix the following sparse warnings.
drivers/watchdog/dw_wdt.c:206:38: warning: incorrect type in argument 1 (different address spaces)
drivers/watchdog/dw_wdt.c:206:38: expected void [noderef] <asn:1>*to
drivers/watchdog/dw_wdt.c:206:38: got struct watchdog_info *<noident>
drivers/watchdog/dw_wdt.c:211:24: warning: incorrect type in initializer (different address spaces)
drivers/watchdog/dw_wdt.c:211:24: expected int const [noderef] <asn:1>*register __p
drivers/watchdog/dw_wdt.c:211:24: got int *<noident>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Enable auto loading by udev when imx2_wdt is compiled as a module.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This is necessary to make the driver work with platforms using the
common clock framework.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
