summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-09-23usb: musb: Fix session based PM for first invalid VBUSTony Lindgren
With the session bit based PM runtime working on musb, we've implemented few quirks to attempt to detect the current state of the hardware. One of the quirks is for invalid VBUS as peripheral, but it is not working in all cases. If we start musb on dm3730 as a peripheral with no cable connected, we will get the devctl 91 state once and will never idle as there are not further interrupts from musb. So we need to ignore the first devctl 91 state as there will be more interrupts if we're connected. The invalid VBUS state also can happen always when connected to certain USB hubs. Looks like musb on dm3730 can claim invalid VBUS with some hubs while 3717-evm and BeagleBone don't. This causes session as peripheral to fail for dm3730 with some hubs. This too is fixed by ignoring only the first invalid VBUS. When connected, we can just look at the session bit as that will clear automatically when the session ends. Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23usb: musb: Fix PM runtime for disconnect after unconfigureTony Lindgren
If we unconfigure musb as a USB peripheral with cable connected, and then remove the cable, no interrupts will happen. And musb thinks we're still connected keeping the device active. Now with the session bit based PM runtime working for musb, we can fix this issue by calling musb irq_work. That rechecks the devctl register and reconfigures PM runtime based on the devctl. Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23arm64: kgdb: handle read-only text / modulesAKASHI Takahiro
Handle read-only cases when CONFIG_DEBUG_RODATA (4.0) or CONFIG_DEBUG_SET_MODULE_RONX (3.18) are enabled by using aarch64_insn_write() instead of probe_kernel_write() as introduced by commit 2f896d586610 ("arm64: use fixmap for text patching") in 4.0. Fixes: 11d91a770f1f ("arm64: Add CONFIG_DEBUG_SET_MODULE_RONX support") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2016-09-23EDAC, altera: Add IRQ Flags to disable IRQ while handlingThor Thayer
Add the IRQF_ONESHOT and IRQF_TRIGGER_HIGH flags to disable the IRQ while executing the IRQ handler. Remove the IRQF_SHARED because these are not shared IRQs in the domain. Exposed when flooding IRQs. Signed-off-by: Thor Thayer <tthayer@opensource.altera.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/1474582419-7053-2-git-send-email-tthayer@opensource.altera.com Signed-off-by: Borislav Petkov <bp@suse.de>
2016-09-23EDAC, altera: Correct EDAC IRQ error messageThor Thayer
Correct the error message sent out in the case of a single bit error IRQ allocation. Signed-off-by: Thor Thayer <tthayer@opensource.altera.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/1474582419-7053-1-git-send-email-tthayer@opensource.altera.com Signed-off-by: Borislav Petkov <bp@suse.de>
2016-09-23arm64: Call numa_store_cpu_info() earlier.David Daney
The wq_numa_init() function makes a private CPU to node map by calling cpu_to_node() early in the boot process, before the non-boot CPUs are brought online. Since the default implementation of cpu_to_node() returns zero for CPUs that have never been brought online, the workqueue system's view is that *all* CPUs are on node zero. When the unbound workqueue for a non-zero node is created, the tsk_cpus_allowed() for the worker threads is the empty set because there are, in the view of the workqueue system, no CPUs on non-zero nodes. The code in try_to_wake_up() using this empty cpumask ends up using the cpumask empty set value of NR_CPUS as an index into the per-CPU area pointer array, and gets garbage as it is one past the end of the array. This results in: [ 0.881970] Unable to handle kernel paging request at virtual address fffffb1008b926a4 [ 1.970095] pgd = fffffc00094b0000 [ 1.973530] [fffffb1008b926a4] *pgd=0000000000000000, *pud=0000000000000000, *pmd=0000000000000000 [ 1.982610] Internal error: Oops: 96000004 [#1] SMP [ 1.987541] Modules linked in: [ 1.990631] CPU: 48 PID: 295 Comm: cpuhp/48 Tainted: G W 4.8.0-rc6-preempt-vol+ #9 [ 1.999435] Hardware name: Cavium ThunderX CN88XX board (DT) [ 2.005159] task: fffffe0fe89cc300 task.stack: fffffe0fe8b8c000 [ 2.011158] PC is at try_to_wake_up+0x194/0x34c [ 2.015737] LR is at try_to_wake_up+0x150/0x34c [ 2.020318] pc : [<fffffc00080e7468>] lr : [<fffffc00080e7424>] pstate: 600000c5 [ 2.027803] sp : fffffe0fe8b8fb10 [ 2.031149] x29: fffffe0fe8b8fb10 x28: 0000000000000000 [ 2.036522] x27: fffffc0008c63bc8 x26: 0000000000001000 [ 2.041896] x25: fffffc0008c63c80 x24: fffffc0008bfb200 [ 2.047270] x23: 00000000000000c0 x22: 0000000000000004 [ 2.052642] x21: fffffe0fe89d25bc x20: 0000000000001000 [ 2.058014] x19: fffffe0fe89d1d00 x18: 0000000000000000 [ 2.063386] x17: 0000000000000000 x16: 0000000000000000 [ 2.068760] x15: 0000000000000018 x14: 0000000000000000 [ 2.074133] x13: 0000000000000000 x12: 0000000000000000 [ 2.079505] x11: 0000000000000000 x10: 0000000000000000 [ 2.084879] x9 : 0000000000000000 x8 : 0000000000000000 [ 2.090251] x7 : 0000000000000040 x6 : 0000000000000000 [ 2.095621] x5 : ffffffffffffffff x4 : 0000000000000000 [ 2.100991] x3 : 0000000000000000 x2 : 0000000000000000 [ 2.106364] x1 : fffffc0008be4c24 x0 : ffffff0ffffada80 [ 2.111737] [ 2.113236] Process cpuhp/48 (pid: 295, stack limit = 0xfffffe0fe8b8c020) [ 2.120102] Stack: (0xfffffe0fe8b8fb10 to 0xfffffe0fe8b90000) [ 2.125914] fb00: fffffe0fe8b8fb80 fffffc00080e7648 . . . [ 2.442859] Call trace: [ 2.445327] Exception stack(0xfffffe0fe8b8f940 to 0xfffffe0fe8b8fa70) [ 2.451843] f940: fffffe0fe89d1d00 0000040000000000 fffffe0fe8b8fb10 fffffc00080e7468 [ 2.459767] f960: fffffe0fe8b8f980 fffffc00080e4958 ffffff0ff91ab200 fffffc00080e4b64 [ 2.467690] f980: fffffe0fe8b8f9d0 fffffc00080e515c fffffe0fe8b8fa80 0000000000000000 [ 2.475614] f9a0: fffffe0fe8b8f9d0 fffffc00080e58e4 fffffe0fe8b8fa80 0000000000000000 [ 2.483540] f9c0: fffffe0fe8d10000 0000000000000040 fffffe0fe8b8fa50 fffffc00080e5ac4 [ 2.491465] f9e0: ffffff0ffffada80 fffffc0008be4c24 0000000000000000 0000000000000000 [ 2.499387] fa00: 0000000000000000 ffffffffffffffff 0000000000000000 0000000000000040 [ 2.507309] fa20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 [ 2.515233] fa40: 0000000000000000 0000000000000000 0000000000000000 0000000000000018 [ 2.523156] fa60: 0000000000000000 0000000000000000 [ 2.528089] [<fffffc00080e7468>] try_to_wake_up+0x194/0x34c [ 2.533723] [<fffffc00080e7648>] wake_up_process+0x28/0x34 [ 2.539275] [<fffffc00080d3764>] create_worker+0x110/0x19c [ 2.544824] [<fffffc00080d69dc>] alloc_unbound_pwq+0x3cc/0x4b0 [ 2.550724] [<fffffc00080d6bcc>] wq_update_unbound_numa+0x10c/0x1e4 [ 2.557066] [<fffffc00080d7d78>] workqueue_online_cpu+0x220/0x28c [ 2.563234] [<fffffc00080bd288>] cpuhp_invoke_callback+0x6c/0x168 [ 2.569398] [<fffffc00080bdf74>] cpuhp_up_callbacks+0x44/0xe4 [ 2.575210] [<fffffc00080be194>] cpuhp_thread_fun+0x13c/0x148 [ 2.581027] [<fffffc00080dfbac>] smpboot_thread_fn+0x19c/0x1a8 [ 2.586929] [<fffffc00080dbd64>] kthread+0xdc/0xf0 [ 2.591776] [<fffffc0008083380>] ret_from_fork+0x10/0x50 [ 2.597147] Code: b00057e1 91304021 91005021 b8626822 (b8606821) [ 2.603464] ---[ end trace 58c0cd36b88802bc ]--- [ 2.608138] Kernel panic - not syncing: Fatal exception Fix by moving call to numa_store_cpu_info() for all CPUs into smp_prepare_cpus(), which happens before wq_numa_init(). Since smp_store_cpu_info() now contains only a single function call, simplify by removing the function and out-lining its contents. Suggested-by: Robert Richter <rric@kernel.org> Fixes: 1a2db300348b ("arm64, numa: Add NUMA support for arm64 platforms.") Cc: <stable@vger.kernel.org> # 4.7.x- Signed-off-by: David Daney <david.daney@cavium.com> Reviewed-by: Robert Richter <rrichter@cavium.com> Tested-by: Yisheng Xie <xieyisheng1@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2016-09-23devpts: Change the owner of /dev/pts/ptmx to the mounter of /dev/ptsEric W. Biederman
In 99.99% of the cases only root in a user namespace can mount /dev/pts and in those cases the owner of /dev/pts/ptmx will remain root.root In the oddball case where someone else has CAP_SYS_ADMIN this code modifies the /dev/pts mount code to use current_fsuid and current_fsgid as the values to use when creating the /dev/ptmx inode. As is done when any other file is created. This is a code simplification, and it allows running without a root user entirely. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23devpts: Remove sync_filesystemsEric W. Biederman
devpts does not and never will have anything to sync so don't bother calling sync_filesystems on remount. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23devpts: Make devpts_kill_sb safe if fsi is NULLEric W. Biederman
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23devpts: Simplify devpts_mount by using mount_nodevEric W. Biederman
Now that all of the work of setting up a superblock has been moved to devpts_fill_super simplify devpts_mount by calling mount_nodev instead of rolling mount_nodev by hand. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23devpts: Move the creation of /dev/pts/ptmx into fill_superEric W. Biederman
The code makes more sense here and things are just clearer. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23devpts: Move parse_mount_options into fill_superEric W. Biederman
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-23initramfs: Escape colons in depfileMichal Marek
Special characters are problematic in depfiles, but we can fix colons easily. Reported-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michal Marek <mmarek@suse.com>
2016-09-23mtd: nand: Provide nand_cleanup() function to free NAND related resourcesRichard Weinberger
Provide a nand_cleanup() function to free all nand related resources without unregistering the mtd device. This should allow drivers to call mtd_device_unregister() and handle its return value and still being able to cleanup all nand related resources. Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Daniel Walter <dwalter@sigma-star.at> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: Kill the OF_MTD Kconfig optionBoris Brezillon
Commit d48f62b9a0a0 ("mtd: nand: move of_get_nand_xxx() helpers into nand_base.c") removed the drivers/of/of_mtd.c file but did not remove the associated OF_MTD Kconfig option. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: mxc: Test CONFIG_OF instead of CONFIG_OF_MTDBoris Brezillon
We are about to drop the OF_MTD Kconfig option. Test CONFIG_OF activation instead of CONFIG_OF_MTD. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Fix nand_command_lp() for 8bits opcodesBoris Brezillon
8 bits opcodes should be followed by a single address cycle. Make the 2nd address cycle dependent of !nand_opcode_8bits(command). Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: sunxi: Support ECC maximizationBoris Brezillon
Setup the maximum ECC config when NAND_ECC_MAXIMIZE is set. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Support maximizing ECC when using software BCHBoris Brezillon
Add support for ECC maximization when software BCH with nand_ooblayout_lp_ops layout is used. Other cases should be handled by the NAND controller driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Add an option to maximize the ECC strengthBoris Brezillon
The generic NAND DT bindings allows one to tweak the ECC strength and step size to their need. It can be used to lower the ECC strength to match a bootloader/firmware config, but might also be used to get a better reliability. In the latter case, the user might want to use the maximum ECC strength without having to explicitly calculate the exact value (this value not only depends on the OOB size, but also on the NAND controller, and can be tricky to extract). Add a generic 'nand-ecc-maximize' DT property and the associated NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best ECC strength and step-size on their own. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Rob Herring <robh@kernel.org>
2016-09-23mtd: nand: mxc: Add timing setup for v2 controllersSascha Hauer
So far we relied on reset default or the bootloader to configure a suitable clk rate for the Nand controller. This works but we can optimize the timing for better performance. This sets the clk rate for v2 controllers (i.MX25/35) based on the timing mode read from the ONFI parameter page. This may also enable the symmetric mode (aks EDO mode) if necessary which reads one word per clock cycle. Tested on an i.MX25 with a Micron MT29F4G08ABBDAHC attached. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: mxc: implement onfi get/set featuresSascha Hauer
To be able to support different ONFI timing modes we have to implement the onfi_set_features and onfi_get_features. Tested on an i.MX25 SoC. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: sunxi: switch from manual to automated timing configSascha Hauer
The NAND framework is now able to select the best NAND timings for us. All we have to do is implement a ->setup_data_interface() function to apply those timings and remove the timing selection code from the sunxi driver. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: automate NAND timings selectionBoris Brezillon
The NAND framework provides several helpers to query timing modes supported by a NAND chip, but this implies that all NAND controller drivers have to implement the same timings selection dance. Also currently NAND devices can be resetted at arbitrary places which also resets the timing for ONFI chips to timing mode 0. Provide a common logic to select the best timings based on ONFI or ->onfi_timing_mode_default information. Hook this into nand_reset() to make sure the new timing is applied each time during a reset. NAND controller willing to support timings adjustment should just implement the ->setup_data_interface() method. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2016-09-23mtd: nand: Expose data interface for ONFI mode 0Sascha Hauer
The nand layer will need ONFI mode 0 to use it as timing mode before and right after reset. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Add function to convert ONFI mode to data_interfaceSascha Hauer
onfi_init_data_interface() initializes a data interface with values from a given ONFI mode. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: convert ONFI mode into data interfaceSascha Hauer
struct nand_data_interface is the designated type to pass to the NAND drivers to configure the timing. To simplify further patches convert the onfi_sdr_timings array from type struct nand_sdr_timings nand_data_interface. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Introduce nand_data_interfaceSascha Hauer
Currently we have no data structure to fully describe a NAND timing. We only have struct nand_sdr_timings for NAND timings in SDR mode, but nothing for DDR mode and also no container to store both types of timing. This patch adds struct nand_data_interface which stores the timing type and a union of different timings. This can be used to pass to drivers in order to configure the timing. Add kerneldoc for struct nand_sdr_timings while touching it anyway. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Create a NAND reset functionSascha Hauer
When NAND devices are resetted some initialization may have to be done, like for example they have to be configured for the timing mode that shall be used. To get a common place where this initialization can be implemented create a nand_reset() function. This currently only issues a NAND_CMD_RESET to the NAND device. The places issuing this command manually are replaced with a call to nand_reset(). Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: remove unnecessary 'extern' from function declarationsSascha Hauer
'extern' is not necessary for function declarations. To prevent people from adding the keyword to new declarations remove the existing ones. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23MAINTAINERS: Add maintainer entry for Ingenic JZ4780 NAND driverHarvey Hunt
Signed-off-by: Harvey Hunt <harveyhuntnexus@gmail.com> Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Cc: linux-mtd@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Allow MTD_NAND_OMAP2 to be usable on Keystone devicesRoger Quadros
Some Keystone devices (e.g. K2G) include a OMAP NAND IP. Allow the NAND driver to be usable for both Keystone and OMAP devices. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: brcmnand: iProc big endian and ONFI supportRay Jui
This patch adds big endian and ONFI support for various iProc based SoCs that use the core brcmstb NAND controller This patch was originally implemented by Prafulla Kota <prafulla.kota@broadcom.com> and fully tested on iProc based NS2 SVK Signed-off-by: Prafulla Kota <prafulla.kota@broadcom.com> Signed-off-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com> Acked-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand_bbt: scan for next free bbt block if writing bbt failsKyle Roeschley
If erasing or writing the BBT fails, we should mark the current BBT block as bad and use the BBT descriptor to scan for the next available unused block in the BBT. We should only return a failure if there isn't any space left. Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com> Suggested-by: Jeff Westfahl <jeff.westfahl@ni.com> Tested-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand_bbt: Move BBT block selection logic out of write_bbt()Boris Brezillon
This clarifies the write_bbt() function by removing the write label and simplifying the error/exit path. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
2016-09-23mtd: nand: timings: Reorder tRR_min def in mode 0Boris Brezillon
In the ONFI spec, the tRR_min entry is defined before the tRST_max one. Reoder the definition to make it easier to review. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: timings: Fix tADL_min for ONFI 4.0 chipsBoris Brezillon
ONFI 4.0 spec defines different values for the tADL_min timing. Since we don't want to have different timings depending on the ONFI version, we just set tADL_min to the maximum value (the one specified in the ONFI 4.0 spec). Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: gpmi: get correct free oob spaceHan Xu
change the way to calculate pagesize to get correct free oob space for legacy_set_geometry function. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: sh_flctl: handle dma_submit() errorsBrian Norris
Some build tools noticed that 'cookie' is being set but not used. Might as well catch the errors here and handle them the same way we handle other DMA prep steps. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: s3c2410: Register cpufreq notifier only on S3C24xxKrzysztof Kozlowski
The driver registered for CPU frequency transitions to recalculate its clock when ARM clock frequency changes (ratio between frequencies of ARM's parent clock (fclk) and clock for peripherals remains fixed). This is needed only on S3C24xx platform when cpufreq driver is enabled so limit the ifdef to respective cpufreq Kconfig. Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Get rid of needless 'goto'Andrey Smirnov
Using "goto" and "switch" statement only makes it harder to follow control flow and doesn't bring any advantages. Rewrite the code to avoid using "goto". Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: Error out if cmd_ctrl() is missingAndrey Smirnov
If no user specified chip->select_chip() function is provided, code in nand_base.c will automatically set this hook to nand_select_chip(), which in turn depends on chip->cmd_ctrl() hook being valid. Not providing both of those functions in NAND controller driver (for example by mistake) will result in a bit cryptic segfault. Same is true for chip->cmdfunc(). To avoid the above scenario add a check in nand_scan_dent and error out if cmd_ctrl() is not provided. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Suggested-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23Kconfig: nand: Remove redundant dependency on MTD_NANDAndrey Smirnov
Config MTD_NAND_FSL_IFC is already located inside 'if MTD_NAND' statment, so there's no need to explicitly specify it as a dependency. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23Kconfig: nand: Make MTD_NAND_FSL_ELBC depend on FSL_SOCAndrey Smirnov
MTD_NAND_FSL_ELBC selects FSL_LBC that in turn depends on FSL_SOC, so depending on PPC instead of FSL_SOC leads to this message: warning: (MPC836x_RDK && MTD_NAND_FSL_ELBC && MTD_NAND_FSL_UPM) selects FSL_LBC which has unmet direct dependencies (FSL_SOC) when doing make ARCH=powerpc \ CROSS_COMPILE=powerpc-e500v2-linux-gnuspe- \ allmodconfig" Changing dependency to FSL_SOC fixes that. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23mtd: nand: import nand_hw_control_init()Marc Gonzalez
The code to initialize a struct nand_hw_control is duplicated across several drivers. Factorize it using an inline function. Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-09-23netfilter: nft_lookup: remove superfluous element found checkPablo Neira Ayuso
We already checked for !found just a bit before: if (!found) { regs->verdict.code = NFT_BREAK; return; } if (found && set->flags & NFT_SET_MAP) ^^^^^ So this redundant check can just go away. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2016-09-23netfilter: xt_helper: Use sizeof(variable) instead of literal numberGao Feng
It's better to use sizeof(info->name)-1 as index to force set the string tail instead of literal number '29'. Signed-off-by: Gao Feng <fgao@ikuai8.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2016-09-23netfilter: Enhance the codes used to get random onceGao Feng
There are some codes which are used to get one random once in netfilter. We could use net_get_random_once to simplify these codes. Signed-off-by: Gao Feng <fgao@ikuai8.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2016-09-23netfilter: nf_tables: check tprot_set first when we use xt.thoffLiping Zhang
pkt->xt.thoff is not always set properly, but we use it without any check. For payload expr, it will cause wrong results. For nftrace, we may notify the wrong network or transport header to the user space, furthermore, input the following nft rules, warning message will be printed out: # nft add rule arp filter output meta nftrace set 1 WARNING: CPU: 0 PID: 13428 at net/netfilter/nf_tables_trace.c:263 nft_trace_notify+0x4a3/0x5e0 [nf_tables] Call Trace: [<ffffffff813d58ae>] dump_stack+0x63/0x85 [<ffffffff810a4c0b>] __warn+0xcb/0xf0 [<ffffffff810a4d3d>] warn_slowpath_null+0x1d/0x20 [<ffffffffa0589703>] nft_trace_notify+0x4a3/0x5e0 [nf_tables] [ ... ] [<ffffffffa05690a8>] nft_do_chain_arp+0x78/0x90 [nf_tables_arp] [<ffffffff816f4aa2>] nf_iterate+0x62/0x80 [<ffffffff816f4b33>] nf_hook_slow+0x73/0xd0 [<ffffffff81732bbf>] arp_xmit+0x8f/0xb0 [ ... ] [<ffffffff81732d36>] arp_solicit+0x106/0x2c0 So before we use pkt->xt.thoff, check the tprot_set first. Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2016-09-23netfilter: nf_tables: improve nft payload fast evalLiping Zhang
There's an off-by-one issue in nft_payload_fast_eval, skb_tail_pointer and ptr + priv->len all point to the last valid address plus 1. So if they are equal, we can still fetch the valid data. It's unnecessary to fall back to nft_payload_eval. Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
generated by cgit (git 2.34.1) at 2025-09-30 15:27:53 +0000