| Age | Commit message (Collapse) | Author |
|---|
|
Platform data support has been removed from the DU driver, drop DU
support from the legacy Marzen board file. The multiplatform DT-based
Marzen support should be used instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Platform data support has been removed from the DU driver, drop DU
support from the legacy Lager board file. The multiplatform DT-based
Lager support should be used instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Hardware doesn't place any restrictions on the buffer alignment,
consider this TODO resolved.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In the wil_tx_ring, error message printed when tx attempted
while vring has no space to accommodate all fragments of frame.
Normally, such situation handled by stopping tx queue.
But, if tx queue is by-passed (like pktgen does), this error
will be triggered at high rate and dmesg will be flooded with
this message. Whole system may become unstable and hang with
no possible recover except power cycle.
Rate-limit it to prevent dmesg flooding.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In some compilation environments, result of pointer arithmetic interpreted as int
while in others it is long int. Force conversion to long.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is no need to obtain physical device through
wil->pdev->dev path, as it is done by this macro.
The same device already stored as wiphy's device, thus
wil_to_dev() returns the same device as wil_to_pcie_dev()
Remove unnecessary macros, this allows to drop dependency
by pci.h in the firmware download code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Scan timeout treated as indication for firmware error;
and should be handled in the same way.
Recovery state machine does not perform as designed because
its state is not updated in case of scan timeout.
Fix is to set recovery state machine into the proper state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
RX_HTRSH interrupt is handled in exactly the same manner
as RX_DONE interrupt - fetching accumulated packets from RX
ring. In addition there's a rate limitted warning message.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Propagate reason for the disconnect through the relevant call chains:
- report to cfg80211 reason as reported by the firmware
- provide to the firmware reason as requested by cfg80211
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of killing interrupts during reset when the first one happens,
kill them before issuing the reset.
This fixes an easy to reproduce crash with multiple cards sharing the
same IRQ.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Closes another small IRQ handler race
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
IRQs are suppressed if ah == NULL and ATH_OP_INVALID being set in
common->op_flags. Close a short time window between those two.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Cc: stable@vger.kernel.org
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The brcms_c_attach_malloc() function can call this with a NULL
"wlc->corestate" or "wlc->hw".
Also I threw in a bonus cleanup by deleting an obvious comment and a
no-op NULL assignment. :)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit 2ad69ac5976191e9bb7dc4044204a504653ad1bb. It
causes wireless device disappear when we get -EPROTO error form USB
request. I encounter such situation occasionally when resume form
suspend with RT3070 adapter:
[ 289.619985] ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x0404 with error -71
[ 289.639368] ieee80211 phy0: rt2800_wait_bbp_ready: Error - BBP register access failed, aborting
[ 289.639374] ieee80211 phy0: rt2800usb_set_device_state: Error - Device failed to enter state 4 (-5)
Without the patch, except printing error, device works just fine after
resume.
Currently after timeouts and REGISTER_BUSY_COUNT tuning, we should
not have any "endless loop", though we can wait quite long when driver
is trying to communicate with the device through non functioning USB
connection. Generally the problem that commit 2ad69ac597619 solves
is kinda artificial.
Cc: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Waiting 500ms for register access is too long, decrease this value
to 100ms.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Because of delays on USB we do not have to iterate so many times on
USB hardware when waiting for H/W register become valid.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use provided timeout value in rt2x00usb_vendor_request() instead
of iterating REGISTER_BUSY_COUNT times.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The hardware info now also include radio and phy information, which
can be helpful in debugging issues.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The board revision that is available in hardware can be translated
so it matches the labelling on the board. This is accomplished by
this helper function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently implemented temperature compensation is only valid on some of
supported chips. Other chips do not need temperature compensation or
need different way to do this (not yet implemented in the rt2800
driver). Trying to do run rt2800_get_gain_calibration_delta() when this
is not appropriate on particular chip gives bogus result of TX power
and can make connection unstable.
This is follow up to commit 8c8d2017ba25c510ddf093419048460db1109bc4
"rt2800: fix RT5390 & RT3290 TX power settings regression". On that
commit we avoid setting BBP_R1 register, but the real problem is wrong
temperature compensation calculation.
Reported-and-tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Debugged-by: Ronald Wahl <ronald.wahl@raritan.com>
Cc: Mike Romberg <mike-romberg@comcast.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix missing memory deallocation on error paths in wil_write_file_wmi()
and wil_write_file_txmgmt().
Reported-by: Ahmed Tamrawi <ahmedtamrawi@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
sound/firewire/dice/dice-transaction.c:34:2-3: Unneeded semicolon
Removes unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In several hid drivers it is necessary to calculate the length of an
hid_report. This patch exports the existing static function hid_report_len of
hid-core.c as an inline function in hid.h
Signed-off-by: Mathieu Magnaudet <mathieu.magnaudet@enac.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Proper operation with the rewritten PCI mini driver requires that a flag be set
when interrupts are enabled. This flag was missed. This patch is one of three needed to
fix the kernel regression reported at https://bugzilla.kernel.org/show_bug.cgi?id=88951.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Catalin Iacob <iacobcatalin@gmail.com>
Tested-by: Catalin Iacob <iacobcatalin@gmail.com>
Cc: Catalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In the major update of the rtlwifi-family of drivers, one of the callback entries
was missed, which leads to memory corruption. Unfortunately, this corruption
never caused a kernel oops, but showed up in other parts of the system.
This patch is one of three needed to fix the kernel regression reported at
https://bugzilla.kernel.org/show_bug.cgi?id=88951.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Catalin Iacob <iacobcatalin@gmail.com>
Tested-by: Catalin Iacob <iacobcatalin@gmail.com>
Cc: Catalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In the major update of the rtlwifi-family of drivers, there was an editing
mistake. Unfortunately, this particular error leads to memory corruption that
silently leads to failure of the system. This patch is one of three needed to
fix the kernel regression reported at https://bugzilla.kernel.org/show_bug.cgi?id=88951.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Catalin Iacob <iacobcatalin@gmail.com>
Tested-by: Catalin Iacob <iacobcatalin@gmail.com>
Cc: Catalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
misspellings
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It reverts commit a4b4e0461ec5 ("of: Add standard property for poweroff capability").
As discussed on the mailing list, it makes more sense to rename back to the
old established property name, without the vendor prefix. Problem being that
the word "source" usually tends to be used for inputs and that is out of control
of the OS. The poweroff capability is an output which simply turns the
system-power off. Also, this property might be used by drivers which power-off
the system and power back on subsequent RTC alarms. This seems to suggest to
remove "poweroff" from the property name and to choose "system-power-controller"
as the more generic name. This patchs adds the required renaming changes and
defines an helper function which checks if this property is set.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
"clk_disable"
The clk_disable() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During the removal of all AT91 !DT boards, we removed the AFEB9260. This driver
is !DT and was only used by this board, so we delete it as well.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function graph helper function prepare_ftrace_return() which does the work
to hijack the parent pointer has that parent pointer as its first parameter.
Instead, if we make it the second parameter and have ip as the first parameter
(self_addr), then it can use the %rdi from save_mcount_regs that loads it
already.
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Move all the work from ftrace_caller_setup into save_mcount_regs. This
simplifies the code and makes it easier to understand.
Link: http://lkml.kernel.org/r/CA+55aFxUTUbdxpjVMW8X9c=o8sui7OB_MYPfcbJuDyfUWtNrNg@mail.gmail.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The save_mcount_regs macro saves and restores the required mcount regs that
need to be saved before calling C code. It is done for all the function hook
utilities (static tracing, dynamic tracing, regs, function graph).
When frame pointers are enabled, the ftrace trampolines need to set up
frames and pointers such that a back trace (dump stack) can continue passed
them. Currently, a separate macro is used (create_frame) to do this, but
it's only done for the ftrace_caller and ftrace_reg_caller functions. It
is not done for the static tracer or function graph tracing.
Instead of having a separate macro doing the recording of the frames,
have the save_mcount_regs perform this task. This also has all tracers
saving the frame pointers when needed.
Link: http://lkml.kernel.org/r/CA+55aFwF+qCGSKdGaEgW4p6N65GZ5_XTV=1NbtWDvxnd5yYLiw@mail.gmail.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
mcount regs
The macro save_mcount_regs saves regs onto the stack. But to uncouple the
amount of stack used in that macro from the users of the macro, we need
to have a define that tells all the users how much stack is used by that
macro. This way we can change the amount of stack the macro uses without
breaking its users.
Also remove some dead code that was left over from commit fdc841b58cf5
"ftrace: x86: Remove check of obsolete variable function_trace_stop".
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Currently save_mcount_regs is passed a "skip" parameter to know how much
stack updated the pt_regs, as it tries to keep the saved pt_regs in the
same location for all users. This is rather stupid, especially since the
part stored on the pt_regs has nothing to do with what is suppose to be
in that location.
Instead of doing that, just pass in an "added" parameter that lets that
macro know how much stack was added before it was called so that it
can get to the RIP. But the difference is that it will now offset the
pt_regs by that "added" count. The caller now needs to take care of
the offset of the pt_regs.
This will make it easier to simplify the code later.
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Instead of having save_mcount_regs store the RIP in %rdx as a temp register
to place it in the proper location of the pt_regs on the stack. Use the
%rdi register as the temp register. This lets us remove the extra store
in the ftrace_caller_setup macro.
Link: http://lkml.kernel.org/r/CA+55aFwF+qCGSKdGaEgW4p6N65GZ5_XTV=1NbtWDvxnd5yYLiw@mail.gmail.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The name MCOUNT_SAVE_FRAME is rather confusing as it really isn't a
function frame that is saved, but just the required mcount registers
that are needed to be saved before C code may be called. The word
"frame" confuses it as being a function frame which it is not.
Rename MCOUNT_SAVE_FRAME and MCOUNT_RESTORE_FRAME to save_mcount_regs
and restore_mcount_regs respectively. Noticed the lower case, which
keeps it from screaming at the reviewers.
Link: http://lkml.kernel.org/r/CA+55aFwF+qCGSKdGaEgW4p6N65GZ5_XTV=1NbtWDvxnd5yYLiw@mail.gmail.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Linus pointed out that MCOUNT_SAVE_FRAME is used in only a single file
and that there's no reason that it should be in a header file.
Move the macro to the code that uses it.
Link: http://lkml.kernel.org/r/CA+55aFwF+qCGSKdGaEgW4p6N65GZ5_XTV=1NbtWDvxnd5yYLiw@mail.gmail.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Linus pointed out that there were locations that did the hard coded
update of the parent and rip parameters. One of them was the static tracer
which could also use the ftrace_caller_setup to do that work. In fact,
because it did not use it, it is prone to bugs, and since the static
tracer is hardly ever used (who wants function tracing code always being
called?) it doesn't get tested very often. I only run a few "does it still
work" tests on it. But I do not run stress tests on that code. Although,
since it is never turned off, just having it on should be stressful enough.
(especially for the performance folks)
There's no reason that the static tracer can't also use ftrace_caller_setup.
Have it do so.
Link: http://lkml.kernel.org/r/CA+55aFwF+qCGSKdGaEgW4p6N65GZ5_XTV=1NbtWDvxnd5yYLiw@mail.gmail.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1411262304010.3961@nanos
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The colorspace chapter in the V4L2 Specification was always poorly
written. This patch rewrites it, documenting the new Y'CbCr encoding
and quantization defines and going into much more detail with respect
to how colorspaces are used and what it all means.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Log the new ycbcr_enc and quantization fields. Note that it now
also logs the flags field for the multiplanar buffer type. This was
forgotten when the flags field was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add and copy the new ycbcr_enc and quantization fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add support for the new AdobeRGB and BT.2020 colorspaces as needed for
HDMI 2.0.
Add support to specify the Y'CbCr encoding and quantization range explicitly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
