| Age | Commit message (Collapse) | Author |
|---|
|
Command queue descriptor page size is 4KB and not the page size used by the
kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5 requires at least one interrupt vector for completions so fix the minvec
argument to pci_enable_msix_range() accordingly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call request module on mlx5_ib so it will be available for applications
requiring it, such as installers that require boot over IB.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chunhao Lin says:
====================
r8169:change hardware setting
This patch series contains two hardware setting modification to prevent
hardware become abnormal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cmac engine is the bridge between driver and dash firmware.
Other os may not disable cmac when leave. And r8169 did not allocate any
resources for cmac engine. Disable it to prevent abnormal system behavior.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start
function. This will prevent enable tx/rx before complete hardware tx/rx
setting.
Tx/Rx will be enabled in the end of function rtl_hw_start_8168.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ying Xue says:
====================
tipc: convert name table read-write lock to RCU
Now TIPC name table is statically allocated and is protected with a
Read-Write lock. To enhance the performance of TIPC name table lookup,
we are going to involve RCU lock to protect the name table. As a
consequence, it becomes lockless to concurrently look up name table on
read side. However, before the conversion can be successfully made,
the following two things must be first done:
- change allocation way of name table from static to dynamic
- fix several incorrect locking policy issues
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert tipc name table read-write lock to RCU. After this change,
a new spin lock is used to protect name table on write side while
RCU is applied on read side.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a list_head variable is seen as a new entry to be added to a
list head, it's unnecessary to be initialized with INIT_LIST_HEAD().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tipc name sequence is published, name table lock is released
before name sequence buffer is delivered to remote nodes through its
underlying unicast links. However, when name sequence is withdrawn,
the name table lock is held until the transmission of the removal
message of name sequence is finished. During the process, node lock
is nested in name table lock. To prevent node lock from being nested
in name table lock, while withdrawing name, we should adopt the same
locking policy of publishing name sequence: name table lock should
be released before message is sent.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As tipc_nametbl_lock is used to protect name_table structure, the lock
must be held while all members of name_table structure are accessed.
However, the lock is not obtained while a member of name_table
structure - local_publ_count is read in tipc_nametbl_publish(), as
a consequence, an inconsistent value of local_publ_count might be got.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC internally created a name table which is used to store name
sequences. Now there is a read-write lock - tipc_nametbl_lock to
protect the table, and each name sequence saved in the table is
protected with its private lock. When a name sequence is inserted
or removed to or from the table, its members might need to change.
Therefore, in normal case, the two locks must be held while TIPC
operates the table. However, there are still several places where
we only hold tipc_nametbl_lock without proprerly obtaining name
sequence lock, which might cause the corruption of name sequence.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As TIPC subscriber server is terminated before name table, no user
depends on subscription list of name sequence when name table is
stopped. Therefore, all name sequences stored in name table should
be released whatever their subscriptions lists are empty or not,
otherwise, memory leak might happen.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Name table locking policy is going to be adjusted from read-write
lock protection to RCU lock protection in the future commits. But
its essential precondition is to convert the allocation way of name
table from static to dynamic mode.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size variable is introduced in publ_list struct to help us exactly
calculate SKB buffer sizes needed by publications when all publications
in name table are delivered in bulk in named_distribute(). But if
publication SKB buffer size is assumed to MTU, the size variable in
publ_list struct can be completely eliminated at the cost of wasting
a bit memory space for last SKB.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tero Aho <tero.aho@coriant.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The compute_score functions are a bit difficult to read.
Neaten them a bit to reduce object sizes and make them a
bit more intelligible.
Return early to avoid indentation and avoid unnecessary
initializations.
(allyesconfig, but w/ -O2 and no profiling)
$ size net/ipv[46]/udp.o.*
text data bss dec hex filename
28680 1184 25 29889 74c1 net/ipv4/udp.o.new
28756 1184 25 29965 750d net/ipv4/udp.o.old
17600 1010 2 18612 48b4 net/ipv6/udp.o.new
17632 1010 2 18644 48d4 net/ipv6/udp.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify bcmgenet driver so that it can be used on Broadcom 7xxx
MIPS-based STB platforms without a device tree.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BTW, do we want memcpy_nocache()?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
initialization of kvec-backed iov_iter
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This patch adds proper handling of the vNIC hot removal event, which includes
a rescind-channel-offer message from the host side that triggers vNIC close and
removal. In this case, the notices to the host during close and removal is not
necessary because the channel is rescinded. This patch blocks these unnecessary
messages, and lets vNIC removal process complete normally.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expand DIV_KX to use BPF_MOD operation in the
DIV_KX bpf 'classic' test.
CC: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove optimize_div() from BPF_MOD | BPF_K case
since we don't know the dividend and fix the
emit_mod() by reading the mod operation result from HI register
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Willem de Bruijn says:
====================
timestamping updates
The main goal for this patchset is to allow correlating timestamps
with the egress interface. Also introduce a warning, as discussed
previously, and update the tests to verify the new feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation:
expand explanation of timestamp counter
Test:
new: flag -I requests and prints PKTINFO
new: flag -x prints payload (possibly truncated)
fix: remove pretty print that breaks common flag '-l 1'
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow reading of timestamps and cmsg at the same time on all relevant
socket families. One use is to correlate timestamps with egress
device, by asking for cmsg IP_PKTINFO.
on AF_INET sockets, call the relevant function (ip_cmsg_recv). To
avoid changing legacy expectations, only do so if the caller sets a
new timestamping flag SOF_TIMESTAMPING_OPT_CMSG.
on AF_INET6 sockets, IPV6_PKTINFO and all other recv cmsg are already
returned for all origins. only change is to set ifindex, which is
not initialized for all error origins.
In both cases, only generate the pktinfo message if an ifindex is
known. This is not the case for ACK timestamps.
The difference between the protocol families is probably a historical
accident as a result of the different conditions for generating cmsg
in the relevant ip(v6)_recv_error function:
ipv4: if (serr->ee.ee_origin == SO_EE_ORIGIN_ICMP) {
ipv6: if (serr->ee.ee_origin != SO_EE_ORIGIN_LOCAL) {
At one time, this was the same test bar for the ICMP/ICMP6
distinction. This is no longer true.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
v1 -> v2
large rewrite
- integrate with existing pktinfo cmsg generation code
- on ipv4: only send with new flag, to maintain legacy behavior
- on ipv6: send at most a single pktinfo cmsg
- on ipv6: initialize fields if not yet initialized
The recv cmsg interfaces are also relevant to the discussion of
whether looping packet headers is problematic. For v6, cmsgs that
identify many headers are already returned. This patch expands
that to v4. If it sounds reasonable, I will follow with patches
1. request timestamps without payload with SOF_TIMESTAMPING_OPT_TSONLY
(http://patchwork.ozlabs.org/patch/366967/)
2. sysctl to conditionally drop all timestamps that have payload or
cmsg from users without CAP_NET_RAW.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One line change, in response to catching an occurrence of this bug.
See also fix f4713a3dfad0 ("net-timestamp: make tcp_recvmsg call ...")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
... without bothering with copy_..._user()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Replace PAGE_KERNEL with PAGE_KERNEL_EXEC to allow copy_to_user_page
invalidate icache for pages mapped with kmap.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
This allows using runtime power management feature on Xtensa.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
drm-next
Merge mst tiling patches and MST fixes
* 'drm-mst-next' of ssh://people.freedesktop.org/~/linux:
drm/fb: add support for tiled monitor configurations. (v2)
drm/tile: expose the tile property to userspace (v3)
drm/connector: store tile information from displayid (v3)
drm/mst: cached EDID for logical ports (v2)
drm: add tile_group support. (v3)
drm/displayid: add displayid defines and edid extension (v2)
drm/dp-mst: Remove branches before dropping the reference
drm/fb_helper: move deferred fb checking into restore mode (v2)
drm/dp: retry AUX transactions 32 times (v1.1)
|
|
This adds fbdev/con support for tiled monitors, so that we
only set a mode on the correct half of the monitor, or
span the two halves if needed.
v2: remove unneeded ERROR, fix | vs ||
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This takes the tiling info from the connector and
exposes it to userspace, as a blob object in a
connector property.
The contents of the blob is ABI.
v2: add property + function documentation.
v3: move property setup from previous patch.
add boilerplate + fix long line (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This creates a tile group from DisplayID block, and
stores the pieces of parsed info from the DisplayID block
into the connector.
v2: add missing signoff, add new connector bits to docs.
v3: remove some debugging.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Logical ports are never going to have EDID changes,
they are used for the internal ports on MST monitors.
We cache the EDIDs from these to save time at MST probe.
v2: drop misplace tile property line, meant for other patch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
A tile group is an identifier shared by a single monitor,
DisplayID topology has 8 bytes we can use for this, just
use those for now until something else comes up in the
future. We assign these to an idr and use the idr to
tell userspace what connectors are in the same tile group.
DisplayID v1.3 says the serial number must be unique for
displays from the same manufacturer.
v2:
destroy idr (dvdhrm)
add docbook (danvet)
airlied:- not sure how to make docbook add fns to tile group section.
v3: fix missing unlock.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
These are just taken from the DisplayID v1.3 spec, and the
DDC spec.
v2: use __packed (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When we unplug a dp mst branch we unreference the entire tree from
the root towards the leaves. Which is ok, since that's the way the
pointers and so also the refcounts go.
But when we drop the reference we must make sure that we remove the
branches/ports from the lists/pointers before dropping the reference.
Otherwise the get_validated functions will still return it instead
of returning NULL (which indicates a potentially on-going unplug).
The mst branch destroy gets this right for ports: First it deletes
the port from the ports list, then it unrefs. But the ports destroy
function gets it wrong: First it unrefs, then it drops the ref. Which
means a zombie mst branch can still be validate with get_validated_mstb_ref
when it shouldn't.
Fix this.
This should address a backtrace Dave dug out somewhere on unplug:
[<ffffffffa00cc262>] drm_dp_mst_get_validated_mstb_ref_locked+0x92/0xa0 [drm_kms_helper]
[<ffffffffa00cc211>] drm_dp_mst_get_validated_mstb_ref_locked+0x41/0xa0 [drm_kms_helper]
[<ffffffffa00cc2aa>] drm_dp_get_validated_mstb_ref+0x3a/0x60 [drm_kms_helper]
[<ffffffffa00cc2fb>] drm_dp_payload_send_msg.isra.14+0x2b/0x100 [drm_kms_helper]
[<ffffffffa00cc547>] drm_dp_update_payload_part1+0x177/0x360 [drm_kms_helper]
[<ffffffffa015c52e>] intel_mst_disable_dp+0x3e/0x80 [i915]
[<ffffffffa013d60b>] haswell_crtc_disable+0x1cb/0x340 [i915]
[<ffffffffa0136739>] intel_crtc_control+0x49/0x100 [i915]
[<ffffffffa0136857>] intel_crtc_update_dpms+0x67/0x80 [i915]
[<ffffffffa013fa59>] intel_connector_dpms+0x59/0x70 [i915]
[<ffffffffa015c752>] intel_dp_destroy_mst_connector+0x32/0xc0 [i915]
[<ffffffffa00cb44b>] drm_dp_destroy_port+0x6b/0xa0 [drm_kms_helper]
[<ffffffffa00cb588>] drm_dp_destroy_mst_branch_device+0x108/0x130 [drm_kms_helper]
[<ffffffffa00cb3cd>] drm_dp_port_teardown_pdt+0x3d/0x50 [drm_kms_helper]
[<ffffffffa00cdb79>] drm_dp_mst_handle_up_req+0x499/0x540 [drm_kms_helper]
[<ffffffff810d9ead>] ? trace_hardirqs_on_caller+0x15d/0x200 [<ffffffffa00cdc73>]
drm_dp_mst_hpd_irq+0x53/0xa00 [drm_kms_helper] [<ffffffffa00c7dfb>]
? drm_dp_dpcd_read+0x1b/0x20 [drm_kms_helper] [<ffffffffa0153ed8>]
? intel_dp_dpcd_read_wake+0x38/0x70 [i915] [<ffffffffa015a225>]
intel_dp_check_mst_status+0xb5/0x250 [i915] [<ffffffffa015ac71>]
intel_dp_hpd_pulse+0x181/0x210 [i915] [<ffffffffa01104f6>]
i915_digport_work_func+0x96/0x120 [i915]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
On MST systems the monitors don't appear when we set the fb up,
but plymouth opens the drm device and holds it open while they
come up, when plymouth finishes and lastclose gets called we
don't do the delayed fb probe, so the monitor never appears on the
console.
Fix this by moving the delayed checking into the mode restore.
v2: Daniel suggested that ->delayed_hotplug is set under
the mode_config mutex, so we should check it under that as
well, while we are in the area.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
At least on two MST devices I've tested with, when
they are link training downstream, they are totally
unable to handle aux ch msgs, so they defer like nuts.
I tried 16, it wasn't enough, 32 seems better.
This fixes one Dell 4k monitor and one of the
MST hubs.
v1.1: fixup comment (Tom).
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
To improve recovery speed, f2fs try to readahead many contiguous blocks in warm
node segment, but for most time, abnormal power-off do not occur frequently, so
when mount a normal power-off f2fs image, by contrary ra so many blocks and then
invalid them will hurt the performance of mount.
It's better to just ra the first next-block for normal condition.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
This patch does cleanup work, it introduces is_valid_blkaddr() to include
verification code for blkaddr with upper and down boundary value which were in
ra_meta_pages previous.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
1.We use zero as upper boundary value for ra SSA/CP blocks, we will skip
readahead as verification failure with max number, it causes low performance.
2.Low boundary value is not accurate for SSA/CP/POR region verification, so
these values need to be redefined.
This patch fixes above issues.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
* pm-runtime: (25 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
PM / Kconfig: Do not select PM directly from Kconfig files
PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
...
|
|
* pm-cpufreq: (21 commits)
intel_pstate: skip this driver if Sun server has _PPC method
cpufreq: arm_big_little: free OPP table created during ->init()
imx6q: free OPP table created during ->init()
exynos5440: free OPP table created during ->init()
cpufreq-dt: free OPP table created during ->init()
cpufreq-dt: register cooling device from ->ready() callback
cpufreq: Introduce ->ready() callback for cpufreq drivers
cpufreq-dt: pass 'policy->related_cpus' to of_cpufreq_cooling_register()
cpufreq: Fix formatting issues in 'struct cpufreq_driver'
cpufreq: pxa2xx: Add Kconfig entry
cpufreq: Ref the policy object sooner
cpufreq: Kconfig: Remove architecture specific menu entries
cpufreq: pcc: Enable autoload of pcc-cpufreq for ACPI processors
intel_pstate: Add CPUID for BDW-H CPU
intel_pstate: Add support for HWP
x86: Add support for Intel HWP feature detection.
cpufreq: respect the min/max settings from user space
cpufreq: cpufreq-dt: Handle regulator_get_voltage() failure
cpufreq: cpufreq-dt: Improve debug about matching OPP
cpufreq: Loongson1: Add cpufreq driver for Loongson1B
...
|
|
* pm-cpuidle:
cpuidle: add MAINTAINERS entry for ARM Exynos cpuidle driver
drivers: cpuidle: Remove cpuidle-arm64 duplicate error messages
drivers: cpuidle: Add idle-state-name description to ARM idle states
drivers: cpuidle: Add status property to ARM idle states
cpuidle: Invert CPUIDLE_FLAG_TIME_VALID logic
|
|
* pm-domains:
ARM: shmobile: Convert to genpd flags for PM clocks for R-mobile
ARM: shmobile: Convert to genpd flags for PM clocks for r8a7779
PM / Domains: Initial PM clock support for genpd
PM / Domains: Power on the PM domain right after attach completes
PM / Domains: Move struct pm_domain_data to pm_domain.h
PM / Domains: Extract code to power off/on a PM domain
PM / Domains: Make genpd parameter of pm_genpd_present() const
* pm-sleep:
PM / hibernate: Deletion of an unnecessary check before the function call "vfree"
PM / Hibernate: Migrate to ktime_t
* pm-tools:
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
