| Age | Commit message (Collapse) | Author |
|---|
|
blk_mq_can_use_cached_rq doesn't just check if we can use the request,
but also performs the work to actually use it. Remove the _can in the
naming, and improve the comment describing the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240111135705.2155518-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Utilize the %pe print specifier to get the symbolic error name as a
string (i.e "-ENOMEM") in the log message instead of the error code to
increase its readablility.
This change was suggested in
https://lore.kernel.org/all/92972476-0b1f-4d0a-9951-af3fc8bc6e65@suswa.mountain/
Signed-off-by: Christian Heusel <christian@heusel.eu>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240111231521.1596838-1-christian@heusel.eu
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered
with the following blk_mq_get_driver_tag() in case of getting driver
tag failure.
Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe
the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime
blk_mq_mark_tag_wait() can't get driver tag successfully.
This issue can be reproduced by running the following test in loop, and
fio hang can be observed in < 30min when running it on my test VM
in laptop.
modprobe -r scsi_debug
modprobe scsi_debug delay=0 dev_size_mb=4096 max_queue=1 host_max_queue=1 submit_queues=4
dev=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename`
fio --filename=/dev/"$dev" --direct=1 --rw=randrw --bs=4k --iodepth=1 \
--runtime=100 --numjobs=40 --time_based --name=test \
--ioengine=libaio
Fix the issue by adding one explicit barrier in blk_mq_mark_tag_wait(), which
is just fine in case of running out of tag.
Cc: Jan Kara <jack@suse.cz>
Cc: Kemeng Shi <shikemeng@huaweicloud.com>
Reported-by: Changhui Zhong <czhong@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240112122626.4181044-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It's not easy to let go responsibility for a subsystem that one cared
for for a long time, but Thierry realized that his heart isn't in the
pwm framework any more.
Thierry cared for the pwm subsystem (commit 200efedd8766 ("pwm: Take
over maintainership of the PWM subsystem")) as a maintainer during
nearly 12 years. A big thanks for the time, effort and dedication spend
during that time.
Uwe takes over maintenance.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add a missing mutex_unlock(&thermal_dbg->lock) to this error path.
Fixes: 7ef01f228c9f ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The kernel allocates a memory buffer and provides its location to the
hardware, which uses it to update the HFI table. This allocation occurs
during boot and remains constant throughout runtime.
When resuming from hibernation, the restore kernel allocates a second
memory buffer and reprograms the HFI hardware with the new location as
part of a normal boot. The location of the second memory buffer may
differ from the one allocated by the image kernel.
When the restore kernel transfers control to the image kernel, its HFI
buffer becomes invalid, potentially leading to memory corruption if the
hardware writes to it (the hardware continues to use the buffer from the
restore kernel).
It is also possible that the hardware "forgets" the address of the memory
buffer when resuming from "deep" suspend. Memory corruption may also occur
in such a scenario.
To prevent the described memory corruption, disable HFI when preparing to
suspend or hibernate. Enable it when resuming.
Add syscore callbacks to handle the package of the boot CPU (packages of
non-boot CPUs are handled via CPU offline). Syscore ops always run on the
boot CPU. Additionally, HFI only needs to be disabled during "deep" suspend
and hibernation. Syscore ops only run in these cases.
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
[ rjw: Comment adjustment, subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 0952177f2a1f ("thermal/core/power_allocator: Update once
cooling devices when temp is low") adds an update flag to avoid
triggering a thermal event when there is no need, and the thermal
cdev is updated once when the temperature is low.
But when the trips are writable, and switch_on_temp is set to be a
higher value, the cooling device state may not be reset to 0,
because last_temperature is smaller than switch_on_temp.
For example:
First:
switch_on_temp=70 control_temp=85;
Then userspace change the trip_temp:
switch_on_temp=45 control_temp=55 cur_temp=54
Then userspace reset the trip_temp:
switch_on_temp=70 control_temp=85 cur_temp=57 last_temp=54
At this time, the cooling device state should be reset to 0.
However, because cur_temp(57) < switch_on_temp(70)
last_temp(54) < switch_on_temp(70) ----> update = false,
update is false, the cooling device state can not be reset.
Using the observation that tz->passive can also be regarded as the
temperature status, set the update flag to the tz->passive value.
When the temperature drops below switch_on for the first time, the
states of cooling devices can be reset once, and tz->passive is updated
to 0. In the next round, because tz->passive is 0, cdev->state will not
be updated.
By using the tz->passive value as the "update" flag, the issue above
can be solved, and the cooling devices can be updated only once when the
temperature is low.
Fixes: 0952177f2a1f ("thermal/core/power_allocator: Update once cooling devices when temp is low")
Cc: 5.13+ <stable@vger.kernel.org> # 5.13+
Suggested-by: Wei Wang <wvw@google.com>
Signed-off-by: Di Shen <di.shen@unisoc.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Change the code layout in thermal_cdev_set_cur_state() so it returns
early on errors which is more consistent with what happens elsewhere.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In analogy with some previous thermal netlink API changes, redefine
thermal_notify_cdev_state_update(), thermal_notify_cdev_add() and
thermal_notify_cdev_delete() to take a const cdev pointer as their
first argument and let them extract the requisite information from
there by themselves.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Some *thermal_cooling_device_register() calls pass a string literal as
the 'type' parameter, so kstrdup_const() can be used instead of
kstrdup() to avoid a memory allocation in such cases.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The mitigation episodes are recorded. A mitigation episode happens
when the first trip point is crossed the way up and then the way
down. During this episode other trip points can be crossed also and
are accounted for this mitigation episode. The interesting information
is the average temperature at the trip point, the undershot and the
overshot. The standard deviation of the mitigated temperature will be
added later.
The thermal debugfs directory structure tries to stay consistent with
the sysfs one but in a very simplified way:
thermal/
`-- thermal_zones
|-- 0
| `-- mitigations
`-- 1
`-- mitigations
The content of the mitigations file has the following format:
,-Mitigation at 349988258us, duration=130136ms
| trip | type | temp(°mC) | hyst(°mC) | duration | avg(°mC) | min(°mC) | max(°mC) |
| 0 | passive | 65000 | 2000 | 130136 | 68227 | 62500 | 75625 |
| 1 | passive | 75000 | 2000 | 104209 | 74857 | 71666 | 77500 |
,-Mitigation at 272451637us, duration=75000ms
| trip | type | temp(°mC) | hyst(°mC) | duration | avg(°mC) | min(°mC) | max(°mC) |
| 0 | passive | 65000 | 2000 | 75000 | 68561 | 62500 | 75000 |
| 1 | passive | 75000 | 2000 | 60714 | 74820 | 70555 | 77500 |
,-Mitigation at 238184119us, duration=27316ms
| trip | type | temp(°mC) | hyst(°mC) | duration | avg(°mC) | min(°mC) | max(°mC) |
| 0 | passive | 65000 | 2000 | 27316 | 73377 | 62500 | 75000 |
| 1 | passive | 75000 | 2000 | 19468 | 75284 | 69444 | 77500 |
,-Mitigation at 39863713us, duration=136196ms
| trip | type | temp(°mC) | hyst(°mC) | duration | avg(°mC) | min(°mC) | max(°mC) |
| 0 | passive | 65000 | 2000 | 136196 | 73922 | 62500 | 75000 |
| 1 | passive | 75000 | 2000 | 91721 | 74386 | 69444 | 78125 |
More information for a better understanding of the thermal behavior
will be added after. The idea is to give detailed statistics
information about the undershots and overshots, the temperature speed,
etc... As all the information in a single file is too much, the idea
would be to create a directory named with the mitigation timestamp
where all data could be added.
Please note this code is immune against trip ordering but not against
a trip temperature change while a mitigation is happening. However,
this situation should be extremely rare, perhaps not happening and we
might question ourselves if something should be done in the core
framework for other components first.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: White space fixups, rebase ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The thermal framework does not have any debug information except a
sysfs stat which is a bit controversial. This one allocates big chunks
of memory for every cooling devices with a high number of states and
could represent on some systems in production several megabytes of
memory for just a portion of it. As the sysfs is limited to a page
size, the output is not exploitable with large data array and gets
truncated.
The patch provides the same information than sysfs except the
transitions are dynamically allocated, thus they won't show more
events than the ones which actually occurred. There is no longer a
size limitation and it opens the field for more debugging information
where the debugfs is designed for, not sysfs.
The thermal debugfs directory structure tries to stay consistent with
the sysfs one but in a very simplified way:
thermal/
-- cooling_devices
|-- 0
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
|-- 1
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
|-- 2
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
|-- 3
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
`-- 4
|-- clear
|-- time_in_state_ms
|-- total_trans
`-- trans_table
The content of the files in the cooling devices directory is the same
as the sysfs one except for the trans_table which has the following
format:
Transition Hits
1->0 246
0->1 246
2->1 632
1->2 632
3->2 98
2->3 98
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: White space fixups, rebase ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The depency of FANOTIFY_ACCESS_PERMISSIONS on SECURITY made sure that
the fsnotify permission hooks were never called when SECURITY was
disabled.
Moving the fsnotify permission hook out of the secutiy hook broke that
optimisation.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Closes: https://lore.kernel.org/linux-fsdevel/53682ece-f0e7-48de-9a1c-879ee34b0449@kernel.dk/
Fixes: d9e5d31084b0 ("fsnotify: optionally pass access range in file permission hooks")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20240109182245.38884-1-amir73il@gmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
commit d685aea5e0a8 ("ASoC: audio-graph-card2: fix off by one in
graph_parse_node_multi_nm()") uses ">=" instead of ">" for index check,
but it was wrong. The nm_idx will be increment at end of loop,
thus, ">" is correct.
while (1) {
...
=> if (*nm_idx > nm_max)
break;
...
(*nm_idx)++;
}
Without this patch, "Multi-Codec-1" sample on
${LINUX}/sound/soc/generic/audio-graph-card2-custom-sample.dtsi
will be error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://msgid.link/r/87o7drdqux.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The offending patch introduces memory leak when there is no error, the
memory allocated for the temporary storage is not freed up.
As I have commented, the original code was correct and cleaner to
follow but it was not obvious from the patch that it will introduce
regression.
Fixes: 8c91ca76f448 ("ASoC: SOF: icp3-dtrace: Fix wrong kfree() usage")
Link: https://lore.kernel.org/all/aec61f67-6b4f-49e6-b458-c332983a0ad6@linux.intel.com/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240112132749.28970-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Split function paiext_push_sample() into two parts. The first part
determines the number of bytes to store as raw data in the perf sample
record. This is now function paiext_have_sample().
The second part stores the raw data in the perf event's ring buffer.
No functional change.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Change the function paiext_copy() parameter from a pointer to a
structure to two pointers to memory areas referenced. The other
members of that structure are not needed.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
The PAI crypto counter and PAI NNPA counters start and stop functions
are streamlined. Move the conditions to invoke start and stop functions
to its respective function body and call them unconditionally.
The start and stop functions now determine how to proceed.
No functional change.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Split function paicrypt_push_sample() into two parts. The first part
determines the number of bytes to store as raw data in the perf sample
record. The second part stores the raw data in the perf event's
ring buffer.
No functional change.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Simplify the interface for functions paicrypt_getctr() and
paiext_getctr(). Change the first parameter from a pointer to a
structure to a pointer to a structure member. The other members
of the structure are not needed.
No functional change.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Implement the workaround for ARM Cortex-A510 erratum 3117295. On an
affected Cortex-A510 core, a speculatively executed unprivileged load
might leak data from a privileged load via a cache side channel. The
issue only exists for loads within a translation regime with the same
translation (e.g. same ASID and VMID). Therefore, the issue only affects
the return to EL0.
The erratum and workaround are the same as ARM Cortex-A520 erratum
2966298, so reuse the existing workaround.
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240110-arm-errata-a510-v1-2-d02bc51aeeee@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In preparation to apply ARM64_WORKAROUND_2966298 for multiple errata,
rename the kconfig and capability. No functional change.
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240110-arm-errata-a510-v1-1-d02bc51aeeee@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We no longer disable softirqs or preemption when doing kernel mode SIMD,
and so for fully preemptible kernels, there is no longer a need to do any
explicit yielding (and for non-preemptible kernels, yielding is not
needed either).
That leaves voluntary preemption, where only explicit yield calls may
result in a reschedule. To retain the existing behavior for such a
configuration, we should take the new situation into account, where the
preempt count will be zero rather than one, and yielding to pending
softirqs is unnecessary.
Fixes: aefbab8e77eb ("arm64: fpsimd: Preserve/restore kernel mode NEON at context switch")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240111112447.577640-2-ardb+git@google.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Full LTO takes the '-mbranch-protection=none' passed to the compiler
when generating the dynamic shadow call stack patching code as a hint to
stop emitting PAC instructions altogether. (Thin LTO appears unaffected
by this)
Work around this by stripping unwind tables from the object in question,
which should be sufficient to prevent the patching code from attempting
to patch itself.
Fixes: 3b619e22c460 ("arm64: implement dynamic shadow call stack for Clang")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240110132619.258809-2-ardb+git@google.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Sorting include files in alphabetic order in
drivers/tty/serial/samsung.c revealed the following error:
In file included from drivers/tty/serial/samsung_tty.c:24:
./arch/arm64/include/asm/irq.h:9:43: error: unknown type name ‘cpumask_t’
9 | void arch_trigger_cpumask_backtrace(const cpumask_t *mask, int exclude_cpu);
| ^~~~~~~~~
Include cpumask.h to avoid unknown type errors for parents of irq.h that
don't include cpumask.h.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240110074007.4020016-1-tudor.ambarus@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add a description to Wangxun's common code lib.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From looking at the PCI IDs, every device supported by intelfb is
also supported by i915. Anyone still using intelfb should please
move on to i915, which does everything intelfb does but better.
Removing intelfb is motivated by the driver's excessive use of the
global screen_info state. The state belongs to architecture and
firmware code; device drivers should not attempt to access it. But
fixing intelfb would require a significant change in the driver's
probing logic. As intelfb has been obsolete for nearly 2 decades,
it is probably not worth the effort. Let's just remove it. Also
remove the related documentation.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maik Broemme <mbroemme@libmpq.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Do not clear the global instance of screen_info. If necessary, clearing
fields in screen_info should be done by architecture or firmware code
that maintains the firmware framebuffer.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
After consuming the global screen_info_state in sysfb_init(), the
created platform device maintains the firmware framebuffer. Clear
screen_info to avoid conflicting access. Subsequent kexec reboots
now ignore the firmware framebuffer.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Replace use of screen_info state with the correct interfaces from
the aperture helpers. The state is only for architecture and firmware
code. It is not guaranteed to contain valid data. Drivers are thus
not allowed to use it.
For removing conflicting firmware framebuffers, there are aperture
helpers. Hence replace screen_info with the correct functions that will
remove conflicting framebuffers for the hypervfb driver. For GEN1 PCI
devices, the driver reads the framebuffer base and size from the PCI
BAR, and uses the range for removing the firmware framebuffer. For
GEN2 VMBUS devices no range can be detected, so the driver clears all
firmware framebuffers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Replace use of screen_info state with the correct interface from
the aperture helpers. The state is only for architecture and firmware
code. It is not guaranteed to contain valid data. Drivers are thus
not allowed to use it.
For removing conflicting firmware framebuffers, there are aperture
helpers. Hence replace screen_info with the correct function that will
remove conflicting framebuffers for the hyperv-drm driver. Also
move the call to the correct place within the driver.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When built-in, the sis driver tries to detect the current display mode
from the global screen_info state. That state is only for architecture
and firmware code. Drivers should not use it directly as it's not
guaranteed to contain valid information.
Remove the mode-detection code from sis. Drivers that want to detect a
pre-set mode on probe should read the hardware registers directly.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Currently the %d format specifier is being used for unsigned int values.
Fix this by using the correct %u format specifier. Cleans up cppcheck
warnings:
warning: %d in format string (no. 1) requires 'int' but the argument
type is 'unsigned int'. [invalidPrintfArgType_sint]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The info field in struct sti_struct was used to detect the default
display device. That test is now done with the respective Linux device
and the info field is unused. Remove it.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Update fb_is_primary device() on parisc to detect the primary display
device from the Linux device instance. Aligns the code with the other
architectures. A later patch will remove the fbdev dependency from the
function's interface.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Allocate stifb's instance of fb_info with framebuffer_alloc(). This
is the preferred way of creating fb_info with associated driver data
stored in struct fb_info.par. Requires several, but minor, changes
through out the driver's code.
The intended side effect of this patch is that the new instance of
struct fb_info now has its device field correctly set to the parent
device of the STI ROM. A later patch can detect if the device is the
firmware's primary output. It is also now correctly located within
the Linux device hierarchy.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Helge Deller <deller@gmx.de>
Reviewed-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Store the ROM's parent device in each STI struct, so we can associate
the STI framebuffer with a device.
The new field will eventually replace the fbdev subsystem's info field,
which the function fb_is_primary_device() currently requires to detect
the firmware's output. By using the device instead of the framebuffer
info, a later patch can generalize the helper for use in non-fbdev code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When framebuffer gets closed, the queued deferred IO gets cancelled. This
can cause some last display data to vanish. This is problematic for users
who send a still image to the framebuffer, then close the file: the image
may never appear.
To ensure none of display data get lost, flush the queued deferred IO
first before closing.
Another possible solution is to delete the cancel_delayed_work_sync()
instead. The difference is that the display may appear some time after
closing. However, the clearing of page mapping after this needs to be
removed too, because the page mapping is used by the deferred work. It is
not completely obvious whether it is okay to not clear the page mapping.
For a patch intended for stable trees, go with the simple and obvious
solution.
Fixes: 60b59beafba8 ("fbdev: mm: Deferred IO support")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The driver's fsync() is supposed to flush any pending operation to
hardware. It is implemented in this driver by cancelling the queued
deferred IO first, then schedule it for "immediate execution" by calling
schedule_delayed_work() again with delay=0. However, setting delay=0
only means the work is scheduled immediately, it does not mean the work
is executed immediately. There is no guarantee that the work is finished
after schedule_delayed_work() returns. After this driver's fsync()
returns, there can still be pending work. Furthermore, if close() is
called by users immediately after fsync(), the pending work gets
cancelled and fsync() may do nothing.
To ensure that the deferred IO completes, use flush_delayed_work()
instead. Write operations to this driver either write to the device
directly, or invoke schedule_delayed_work(); so by flushing the
workqueue, it can be guaranteed that all previous writes make it to the
device.
Fixes: 5e841b88d23d ("fb: fsync() method for deferred I/O flush.")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
We have managed to ascertain that all users of the old FBDEV
code that are out of tree are now gone.
The new DRM driver can be found in drivers/gpu/drm/pl111/.
The remaining out of tree user was the ARM FVP emulation
platform, running Android. Thanks to changes in Android
versions 13 and 14, Android can now use the DRM driver when
being emulated under FVP. Some final patches are being put
in place to make it fully featured.
This is essentially a revert of the partial revert in
commit 112c35237c72 ("Partially revert "video: fbdev: amba-clcd: Retire elder CLCD driver"")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
As far as anybody can tell, this product never shipped. If it did,
it shipped in 2007 and nobody has access to one any more. Remove the
fbdev driver and the backlight driver.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
There was a typo in oxygen mixer code that didn't update the right
channel value properly for the capture volume. Let's fix it.
This trivial fix was originally reported on Bugzilla.
Fixes: a3601560496d ("[ALSA] oxygen: add front panel controls")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=156561
Link: https://lore.kernel.org/r/20240112111023.6208-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP.
Fix this issue by removing this check so the userspace can decide on this.
Fixes: cafc3662ee3f ("net: micrel: Add PHC support for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a use case that playback stream of a loopback cable works on
RW_INTERLEAVED mode while capture stream works on MMAP_INTERLEAVED mode:
aplay -Dhw:Loopback,0,0 S32_48K_2ch.wav;
arecord -Dplughw:Loopback,1,0 -fS32_LE -r16000 -c2 cap.wav;
The plug plugin handles only slave PCM support MMAP mode. Not only plug
plugin but also other plugins like direct plugins(dmix/dsnoop/dshare)
work on MMAP access mode. In this case capture stream is the slave
PCM works on MMAP_INTERLEAVED mode. However loopback_check_format()
rejects this access setting and return:
arecord: pcm_read:2240: read error: Input/output error
To fix it a function called is_access_interleaved() is introduced to
get if access is interleaved mode. If both access of capture stream and
playback stream is interleaved mode loopback_check_format() will allow
this kind of access setting.
Fixes: 462494565c27 ("ALSA: aloop: Add support for the non-interleaved access mode")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://lore.kernel.org/r/20240111025219.2678764-1-chancel.liu@nxp.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs update from Jaegeuk Kim:
"In this series, we've some progress to support Zoned block device
regarding to the power-cut recovery flow and enabling
checkpoint=disable feature which is essential for Android OTA.
Other than that, some patches touched sysfs entries and tracepoints
which are minor, while several bug fixes on error handlers and
compression flows are good to improve the overall stability.
Enhancements:
- enable checkpoint=disable for zoned block device
- sysfs entries such as discard status, discard_io_aware, dir_level
- tracepoints such as f2fs_vm_page_mkwrite(), f2fs_rename(),
f2fs_new_inode()
- use shared inode lock during f2fs_fiemap() and f2fs_seek_block()
Bug fixes:
- address some power-cut recovery issues on zoned block device
- handle errors and logics on do_garbage_collect(),
f2fs_reserve_new_block(), f2fs_move_file_range(),
f2fs_recover_xattr_data()
- don't set FI_PREALLOCATED_ALL for partial write
- fix to update iostat correctly in f2fs_filemap_fault()
- fix to wait on block writeback for post_read case
- fix to tag gcing flag on page during block migration
- restrict max filesize for 16K f2fs
- fix to avoid dirent corruption
- explicitly null-terminate the xattr list
There are also several clean-up patches to remove dead codes and
better readability"
* tag 'f2fs-for-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (33 commits)
f2fs: show more discard status by sysfs
f2fs: Add error handling for negative returns from do_garbage_collect
f2fs: Constrain the modification range of dir_level in the sysfs
f2fs: Use wait_event_freezable_timeout() for freezable kthread
f2fs: fix to check return value of f2fs_recover_xattr_data
f2fs: don't set FI_PREALLOCATED_ALL for partial write
f2fs: fix to update iostat correctly in f2fs_filemap_fault()
f2fs: fix to check compress file in f2fs_move_file_range()
f2fs: fix to wait on block writeback for post_read case
f2fs: fix to tag gcing flag on page during block migration
f2fs: add tracepoint for f2fs_vm_page_mkwrite()
f2fs: introduce f2fs_invalidate_internal_cache() for cleanup
f2fs: update blkaddr in __set_data_blkaddr() for cleanup
f2fs: introduce get_dnode_addr() to clean up codes
f2fs: delete obsolete FI_DROP_CACHE
f2fs: delete obsolete FI_FIRST_BLOCK_WRITTEN
f2fs: Restrict max filesize for 16K f2fs
f2fs: let's finish or reset zones all the time
f2fs: check write pointers when checkpoint=disable
f2fs: fix write pointers on zoned device after roll forward
...
|
|
Pull smb server updates from Steve French:
- memory allocation fix
- three lease fixes, including important rename fix
- read only share fix
- thread freeze fix
- three cleanup fixes (two kernel doc related)
- locking fix in setting EAs
- packet header validation fix
* tag '6.8-rc-smb-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: Add missing set_freezable() for freezable kthread
ksmbd: free ppace array on error in parse_dacl
ksmbd: send lease break notification on FILE_RENAME_INFORMATION
ksmbd: don't allow O_TRUNC open on read-only share
ksmbd: vfs: fix all kernel-doc warnings
ksmbd: auth: fix most kernel-doc warnings
ksmbd: Remove usage of the deprecated ida_simple_xx() API
ksmbd: don't increment epoch if current state and request state are same
ksmbd: fix potential circular locking issue in smb2_set_ea()
ksmbd: set v2 lease version on lease upgrade
ksmbd: validate the zero field of packet header
|
|
Pull misc filesystem updates from Al Viro:
"Misc cleanups (the part that hadn't been picked by individual fs
trees)"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
apparmorfs: don't duplicate kfree_link()
orangefs: saner arguments passing in readdir guts
ocfs2_find_match(): there's no such thing as NULL or negative ->d_parent
reiserfs_add_entry(): get rid of pointless namelen checks
__ocfs2_add_entry(), ocfs2_prepare_dir_for_insert(): namelen checks
ext4_add_entry(): ->d_name.len is never 0
befs: d_obtain_alias(ERR_PTR(...)) will do the right thing
affs: d_obtain_alias(ERR_PTR(...)) will do the right thing
/proc/sys: use d_splice_alias() calling conventions to simplify failure exits
hostfs: use d_splice_alias() calling conventions to simplify failure exits
udf_fiiter_add_entry(): check for zero ->d_name.len is bogus...
udf: d_obtain_alias(ERR_PTR(...)) will do the right thing...
udf: d_splice_alias() will do the right thing on ERR_PTR() inode
nfsd: kill stale comment about simple_fill_super() requirements
bfs_add_entry(): get rid of pointless ->d_name.len checks
nilfs2: d_obtain_alias(ERR_PTR(...)) will do the right thing...
zonefs: d_splice_alias() will do the right thing on ERR_PTR() inode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull dcache updates from Al Viro:
"Change of locking rules for __dentry_kill(), regularized refcounting
rules in that area, assorted cleanups and removal of weird corner
cases (e.g. now ->d_iput() on child is always called before the parent
might hit __dentry_kill(), etc)"
* tag 'pull-dcache' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (40 commits)
dcache: remove unnecessary NULL check in dget_dlock()
kill DCACHE_MAY_FREE
__d_unalias() doesn't use inode argument
d_alloc_parallel(): in-lookup hash insertion doesn't need an RCU variant
get rid of DCACHE_GENOCIDE
d_genocide(): move the extern into fs/internal.h
simple_fill_super(): don't bother with d_genocide() on failure
nsfs: use d_make_root()
d_alloc_pseudo(): move setting ->d_op there from the (sole) caller
kill d_instantate_anon(), fold __d_instantiate_anon() into remaining caller
retain_dentry(): introduce a trimmed-down lockless variant
__dentry_kill(): new locking scheme
d_prune_aliases(): use a shrink list
switch select_collect{,2}() to use of to_shrink_list()
to_shrink_list(): call only if refcount is 0
fold dentry_kill() into dput()
don't try to cut corners in shrink_lock_dentry()
fold the call of retain_dentry() into fast_dput()
Call retain_dentry() with refcount 0
dentry_kill(): don't bother with retain_dentry() on slow path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull rename updates from Al Viro:
"Fix directory locking scheme on rename
This was broken in 6.5; we really can't lock two unrelated directories
without holding ->s_vfs_rename_mutex first and in case of same-parent
rename of a subdirectory 6.5 ends up doing just that"
* tag 'pull-rename' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
rename(): avoid a deadlock in the case of parents having no common ancestor
kill lock_two_inodes()
rename(): fix the locking of subdirectories
f2fs: Avoid reading renamed directory if parent does not change
ext4: don't access the source subdirectory content on same-directory rename
ext2: Avoid reading renamed directory if parent does not change
udf_rename(): only access the child content on cross-directory rename
ocfs2: Avoid touching renamed directory if parent does not change
reiserfs: Avoid touching renamed directory if parent does not change
|
