| Age | Commit message (Collapse) | Author |
|---|
|
The BA16 module has a PMIC that uses the WDOG_B output from iMX6 to
reset the system on a watchdog timeout. Configure the watchdog to assert
the external reset signal (WDOG_B) using fsl,ext-reset-output property.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Previously the LDB_DIx clocks could be specified in the ldb node. With
the ERR009219 errata fix applied, the ldb_di clocks now needs to be
specified in the clks node to ensure the clocks are setup early in the
boot process.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The default monitor that ships with B850v3 requires a 65MHz pixel clock.
65MHz can not be achieved using PLL3 (480MHz/7=68.5MHz). Hence set the
LDB_DIx clock source to PLL5. Since PLL5 is already in use by IPU1_DIx,
set the clock source for IPU1_DIx to PLL2_PFD2 to allow simultaneous
display on both LVDS and HDMI interface.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove ldb panel entry for the following reasons:
- The b850v3 has an onboard LVDS to DisplayPort converter (STDP4028). So
we should not limit the monitors that can be connected by hardcoding the
auo,b133htn01 1080p panel.
- The default resolution on the LVDS interface needs to be WXGA or less.
Otherwise when a 1080p monitor is connected to the HDMI port there is no
output on both the LVDS and HDMI ports since a single IPU on i.MX6 can
not handle two 1080p displays. With the panel entry removed from the
devicetree, drm driver defaults the resolution on LVDS interface to XGA.
Once in userspace, applications can set the desired resolution on LVDS
interface over IPU2 CRTC.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "ARM: Keystone DTS for 4.7" from Santosh Shilimkar:
- Remainder k2-* rename to keystone-*
- PSCI node info
- SPI alias nodes for bootloaders
* tag 'keystone_dts_for_4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: dts: add psci command definition
ARM: dts: keystone: Add aliases for SPI nodes
ARM: dts: k2*: Rename the k2* files to keystone-k2* files
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Merge "ARMv7 Vexpress updates/fixes for v4.7" from Sudeep Holla:
1. Support for external expansion bus useful for additional hardware
e.g. LogicTile Express daughterboards (Brian Starkey)
2. Fix for device node name unit-address presence/absence warnings
enabled in recently update DTC (Sudeep Holla)
* tag 'vexpress-for-v4.7/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: Add external expansion bus to DT
ARM: dts: vexpress: fix node name unit-address presence warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.7" from Simon Horman:
* Configure NMI key as wakeup source in DT of kzm9g board
* Add SDHI support to DT of gose board
* Add support of UHS-I SDR-50 for SDHI to DT of r8a7790 SoC
* Correct interrupt type for ARM TWD in DT of r8a7779 and sh73a0 SoCs
* Add IIC support to DT of r8a7794 SoC
* Add CAN support to DT of r8a7793 and r8a7794 SoCs
* Add SCIF2 support to r8a7790 device tree
* Use CAN, JPU and USB3.0 fallback compatibility string
in DT of r8a7791 and r8a7790 SoCs
* tag 'renesas-dt-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: gose: Enable SDHI controllers
ARM: dts: r8a7793: Add SDHI controllers
ARM: dts: r8a7790: fix max-frequency for SDHI
ARM: dts: kzm9g: Configure NMI key as wake-up source
ARM: dts: r8a7790: lager: Enable UHS-I SDR-50
ARM: dts: r8a7790: Set maximum frequencies for SDHI clocks
ARM: dts: r8a7791: Use USB3.0 fallback compatibility string
ARM: dts: r8a7790: Use USB3.0 fallback compatibility string
ARM: dts: r8a7779: Correct interrupt type for ARM TWD
ARM: dts: sh73a0: Correct interrupt type for ARM TWD
ARM: dts: r8a7794: Add IIC nodes
ARM: dts: r8a7794: add IIC clocks
ARM: dts: r8a7793: add CAN nodes to device tree
ARM: dts: r8a7793: add CAN clocks to device tree
ARM: dts: r8a7794: add CAN nodes to device tree
ARM: dts: r8a7794: add CAN clocks to device tree
ARM: dts: r8a7790: use fallback can compatibility string
ARM: dts: r8a7791: use fallback can compatibility string
ARM: dts: r8a7790: Add SCIF2 device node
ARM: dts: r8a7790: Add SCIF2 clock
...
|
|
Fix off by one error in da850 device tree in
the number of INTC interrupts.
Signed-off-by: David Lechner <david@lechnology.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: commit message update]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Disable mdio and eth0 in da850.dtsi file. All other
devices are disabled by default and not all boards
will use these devices, so these should be disabled too.
da850-evm.dtb already had status = "okay" for these devices.
da850-enbw-cmc.dts did not, so they were added.
Signed-off-by: David Lechner <david@lechnology.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: commit description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add AUXDATA needed to match the device-tree node for spi0 to the
non-device-tree clock.
Signed-off-by: David Lechner <david@lechnology.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: commit description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add device node and pinmux for SoC spi0.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The VExpress development platform has an external expansion bus which
can be used for additional hardware (e.g. LogicTile Express daughter
boards).
Add this bus to the VExpress CoreTile device-trees.The bus is described
for a CoreTile occupying site 1.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Commit b993734718c0 ("scripts/dtc: Update to upstream version 53bf130b1cdd")
added warnings on node name unit-address presence/absence mismatch in
the device trees.
This patch fixes those warning on all the vexpress platforms where
unit-address is present in node name while the reg/ranges property is
not present.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Enable the S/PDIF transmitter present on the Cubietruck.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
In order to be standard to manage for rockchip SoCs, move the thermal
data into rk3288 dtsi, we needn't to add a new file for thermal.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Includes regulator and pin assignments.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Same as on r8a7791.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The wrong values come from an old datasheet (H2 v0.6). Anything later
has the fixed value of 195MHz (H2 v0.7 up to Gen2-common V2.0).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add a GPIO key with wake-up capability for the NMI button.
This allows to wake up the system from s2ram without relying on the
buttons on the optional switch board.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,2}.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The clock binding for the main clock controller was changed to an
indexed controller style binding on request of the clk
maintainers. This updates the dtsi to use the new bindings.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Merge "Qualcomm Device Tree Changes for v4.7" from Andy Gross:
* Add DB600C support
* Add IPQ4019 support
* Add additional nodes for APQ8064
* Fix APQ8064 pinctrls for i2c/spi
* Add MSM8974 nodes for smp2p and smd
* Modify MSM8974 memory reserve for rfsa and rmtfs
* Add support for BQ27541 on Nexus7
* tag 'qcom-dt-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (30 commits)
device-tree: nexus7: Add bq27541 battery interface to dts
ARM: dts: db600c: add support to magnetometer
ARM: dts: db600c: add spi support
ARM: dts: db600c: add i2c support
ARM: dts: db600c: Add on board leds support
ARM: dts: db600c: add on board sata support.
ARM: dts: db600c: add pcie support
ARM: dts: db600c: add usb support
ARM: dts: db600c: Add eMMC and SD card support
ARM: dts: db600c: add pmic regulator supplies
ARM: dts: db600c: add board support with serial
ARM: dts: apq8064: add gsbi7 i2c support
ARM: dts: apq8064: add support to gsbi1 uart
ARM: dts: apq8064: fix the pinctrls for i2c and spi
ARM: dts: qcom: apq8064: Add smd node and all edges
ARM: dts: qcom: apq8064: Add complete smsm node
ARM: dts: qcom: apq8064: Add syscon for sic-non-secure
ARM: dts: msm8974: Add modem smp2p and smd nodes
ARM: dts: msm8974: Add node for second i2c from blsp1
ARM: dts: msm8974: Split efs in rfsa and rmtfs
...
|
|
http://github.com/Broadcom/stblinux into next/dt
Merge "Broadcom ARM-based SoC Device Tree changes" from Florian Fainelli:
- Rafal adds proper VCC GPIO to be fed to the USB host controllers for known
BCM5301x devices needing that, he also enables earlycon, and enables the
SPI-NOR flashes on relevant devices
- Eric adds the VideoCore 4 Device Tree nodes to the BCM283x Device Tree and
provides a DRM patch to kick out the simplefb framebuffer to avoid conflicts
- Stephan adds proper CPU nodes for the ARM processor on the BCM2835 SoC Device
Tree
- Martin provides a binding fix for the DMA channel interrupt numbers and
description
* tag 'arm-soc/for-4.7/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM5301X: Add DT entry for SPI controller and NOR flash
dt/bindings: bcm2835: correct description for DMA-int
ARM: bcm2835: add CPU node for ARM core
ARM: bcm2835: Add VC4 to the device tree.
drm/vc4: Kick out the simplefb framebuffer before we set up KMS.
ARM: BCM5301X: Enable earlycon on tested devices
ARM: BCM5301X: Set vcc-gpio for USB controllers of few devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "First set of device tree changes for omaps for v4.7 merge window" from Tony Lindgren:
- Two sets of name and unit address check fixes for dts files.
- DMA, McASP, and timer and regulator related dts changes for dra7
- Add more devices for Nokia N9/N950
- Initial support for am335x ICEv2
- Initial support for am572x-IDK
- Pinctrl changes for am335x-baltos-ir5221
- Initial support for Amazon Kindle Fire (first generation)
- A series of changes to add GPIO controller support for the
GPMC driver. The driver changes will be merged separately.
- Support for am43xx clkout1
- Pinctrl and RTC changes for am335x-chili
- Add support for dra72-evm rev C (SR2.0)
* tag 'omap-for-v4.7/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (61 commits)
ARM: dts: Add support for dra72-evm rev C (SR2.0)
ARM: dts: am335x-chilisom: Enable poweroff PMIC sequence using RTC signal
ARM: dts: am335x-chili*: Move Ethernet MAC description from SOM to board
ARM: dts: am335x-chili*: Move uart0 description from SOM to board
ARM: dts: am43xx: add support for clkout1 clock
ARM: dts: omap3-beagle: Provide NAND ready pin
ARM: dts: am335x: Provide NAND ready pin
ARM: dts: am437x: Provide NAND ready pin
ARM: dts: dra7x-evm: Provide NAND ready pin
ARM: dts: dm816x: Enable gpio controller for GPMC
ARM: dts: dm814x: Enable gpio controller for GPMC
ARM: dts: omap3: Enable gpio controller for GPMC
ARM: dts: am4372: Enable gpio controller for GPMC
ARM: dts: am335x: Enable gpio controller for GPMC
ARM: dts: dra7: Enable gpio controller for GPMC
ARM: dts: omap5: Enable gpio and interrupt controller for GPMC
ARM: dts: omap4: Enable gpio and interrupt controller for GPMC
ARM: dts: omap24xx: Enable gpio and interrupt controller for GPMC
ARM: dts: omap4-kc1: Power off support
ARM: dts: omap4-kc1: LEDs support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC R-Car SYSC Updates for v4.7" from Simon Horman:
* Add DT bindings for the R-Car System Controller.
An implementation is intended to follow.
* tag 'renesas-rcar-sysc-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: Add r8a7795 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7794 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7793 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7791 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7790 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7779 SYSC PM Domain Binding Definitions
PM / Domains: Add DT bindings for the R-Car System Controller
|
|
This commit adds pin-mux nodes for the NAND controller.
Some SoCs support 2 chip selects and the others only support
1 chip select.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "The i.MX device tree updates for 4.7" from Shawn Guo:
- More i.MX6 System-on-Module board support from Ka-Ro electronics:
tx6s-8xxx, tx6u-8xxx, tx6q-1xxx, tx6ul-00xx.
- Nitrogen6_MAX QP and Nitrogen6_SoloX board support from Boundary
Devices.
- VF610 based ZII development board support.
- Add SAI interface audio support for i.MX6SX SDB board.
- A number of random updates on LS1021A and VF610 dts files.
- A couple of pinumx updates on i.MX25 and i.MX28.
* tag 'imx-dt-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (36 commits)
ARM: dts: imx6qdl-udoo: add 7 inch LCD touchscreen panel support
ARM: dts: i.MX3x: add keypad port devicetree nodes
ARM: dts: ls1021a: add pix clock to DCU dts node
ARM: dts: ls1021a: DSPI has 6 chip-selects
ARM: dts: ls1021a: Add gpio support for ls1021a platform
ARM: dts: imx6q-ba16: Remove unused vqmmc-supply
ARM: dts: ls1021a: add SCFG MSI dts node
ARM: dts: imx28: add alternative pinmuxing for mac0
ARM: dts: imx6q-tbs2910: fix fec reset polarity
ARM: dts: vf610-zii-dev: Add ZII development board.
ARM: dts: vfxxx: add missing reg properties
ARM: dts: vf-colibri: increase NAND clock speed
ARM: dts: vf-colibri: alias the primary FEC as ethernet0
ARM: dts: imx6sx-sdb: Add SAI support
bindings: fsl-imx-sdma: Document 'fsl,sdma-event-remap' property
ARM: dts: imx6sx: Remove unused property
ARM: dts: imx6sx: Fix SAI DMA index
ARM: dts: imx6q-ba16: Disable pwm2 by default
ARM: dts: imx: add Boundary Devices Nitrogen6_SoloX board
ARM: dts: imx6qdl-sabresd: Pass the hannstar panel compatible string
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Changes for v4.7-rc1" from Thierry Reding:
A couple of patches that cleanup some Kconfig, enable various features,
use stdout-path to define the debug serial port (so that it doesn't have
to be manually specified on the kernel command-line) and cleanup and fix
some minor device trees bugs.
* tag 'tegra-for-4.7-arm' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Correct interrupt type for ARM TWD
ARM: tegra: Add stdout-path for various boards
ARM: tegra: Replace legacy *,wakeup property with wakeup-source
ARM: tegra: Enable watchdog support for Tegra114 and Tegra124
ARM: tegra: Add high speed UARTs to Jetson TK1 device tree
ARM: tegra: Fix copy/paste typo in several DTS includes
ARM: tegra: Remove redundant ARM_L1_CACHE_SHIFT_6 select
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Merge "Device-Tree updates for DaVinci" from Sekhar Nori:
This contains some clean-up and fixes of device-tree data and addition
of i2c1 node for DA850.
* tag 'davinci-for-v4.7/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for i2c1
ARM: DTS: da850: add node for i2c1
ARM: dts: davinci: use proper address after @
ARM: DTS: da850: fix missing #gpio-cells in gpio node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Merge "Nomadik DTS changes for v4.7" from Linus Walleij:
- Add accelerometer for NHK15
- Add DMA engine definitions and UART channels
* tag 'nomadik-dts-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: nomadik: add DMA engine and some channels
ARM: dts: nomadik: add accelerometer IRQ and pin setting
|
|
Merge "mvebu dt for 4.7 (part 1)" from Gregory CLEMENT:
- add hardware monitor support in the NSA320 device tree
- update makefile with kirkwood-ds112.dtb and kirkwood-nsa320.dtb
- fix GPIO config on the Linksys boards
- various Kirkwood DT warning fixup from the newer DT compiler
* tag 'mvebu-dt-4.7-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Add DTS for Linksys EA4200v2/EA4500
ARM: dts: orion5x: add device tree for kurobox-pro
ARM: dts: kirkwood: Add address go regulator unit name
ARM: dts: kirkwood: Add address to mbus unit name
ARM: dts: kirkwood: Remove address from gpio-i2c unit name
ARM: dts: kirkwood: Fixup pcie DT warnings
ARM: dts: kirkwood: Add address to ethernet-phy unit name
ARM: dts: kirkwood: Remove address from dsa unit name
ARM: dts: kirkwood: Remove node address from leds
ARM: dts: kirkwood: Remove button address and fixup names
ARM: dts: kirkwood: add kirkwood-nsa320.dtb to Makefile
ARM: dts: kirkwood: add kirkwood-ds112.dtb to Makefile
ARM: mvebu: fix GPIO config on the Linksys boards
ARM: dts: kirkwood: Add the hardware monitor to the NSA320 device tree
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Samsung Device Tree updates and improvements for v4.7" from Krzysztof Kozlowski:
1. Enable accelerated AES (Security SubSystem) on Exynos4412-based boards.
2. Enable HDMI CEC on Exynos4412-based Odroid.
3. Add regulator supplies for eMMC/SD on Odroid XU3/XU4.
4. Fix DTC unit name warnings.
5. Merge topic branch of new Artik5 board.
* tag 'samsung-dt-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5p: Fix DTC unit name warnings in SMDKv210 board
ARM: dts: exynos: Fix DTC unit name warnings in Exynos5440
ARM: dts: exynos: Fix DTC unit name warnings in SMDK5420
ARM: dts: exynos: Fix DTC unit name warnings in Peach Pit
ARM: dts: exynos: Fix DTC unit name warnings in Exynos542x
ARM: dts: exynos: Fix DTC unit name warnings in Exynos5250
ARM: dts: exynos: Fix DTC unit name warnings in Exynos4x12
ARM: dts: exynos: Fix DTC unit name warnings in Trats2 board
ARM: dts: exynos: Fix DTC unit name warnings in Exynos4
ARM: dts: exynos: Fix DTC unit name warnings in Exynos3250
ARM: dts: exynos: Fix DTC unit name warnings in cros-adc-thermistors
ARM: dts: exynos: Add eMMC and SD regulator supplies to Odroid XU3/XU4
ARM: dts: exynos: Enable the HDMI CEC device on Exynos4412 Odroid boards
ARM: dts: exynos: Add node for the HDMI CEC device to exynos4
ARM: dts: exynos: Add HDMI CEC pin definition to exynos4 pinctrl
ARM: dts: exynos: Enable SSS on Odroid X/X2/U3 family
ARM: dts: exynos: Enable SSS on Trats2
ARM: dts: exynos: Add Security SubSystem node to Exynos4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Topic branch for Device Tree changes for Exynos 3250 for v4.7" from Krzysztof Kozlowski:
Merge necessary new clocks from Sylwester (used by new board) and add support
for Exynos3250-based Artik5 board.
* tag 'samsung-dt-exynos3250-artik5-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add MSHC2 DT node for SD card for exynos3250-artik5-eval board
ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module
ARM: dts: exynos: Add MSHC2 DT node for Exynos3250 SoC
ARM: dts: exynos: Add UART2 DT node for Exynos3250 SoC
ARM: dts: exynos: Add initial gpio setting of MMC2 device for exynos3250-monk
ARM: dts: exynos: Add initial pin configuration for exynos3250-rinato
clk: samsung: exynos3250: Add MMC2 clock
clk: samsung: exynos3250: Add UART2 clock
dt-bindings: Add the clock id of UART2 and MMC2 for Exynos3250
|
|
The MiQi is a rk3288-based devboard from Shenzen based mqmaker, with a
footprint the size of a credit card.
Main available outside connections are 4 usb ports, hdmi, gigabit
ethernet and two expansion headers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add vendor-prefix for Shenzen-based mqmaker Inc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
|
|
This pull request brings in VC4 devicetree support and the other minor
DT changes for 4.7.
Also included is a DRM patch necessary to prevent regressions when
simplefb and vc4 drivers are both present. The patch was suggested by
the simplefb maintainer as the solution agreed upon at ELCE 2014, and
was acked by the DRM maintainer for merging through this tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Controller is present on every BCM4708* board but only few devices have
serial flash attached so mark it as disabled by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
- 1 GiB of DRAM
- 1 Gigabit ethernet
- 1 USB gadget port
- 1 USB host port with an on-board hub
- 2 QSPI NORs connected to the Cadence QSPI core
- Multiple I2C EEPROMs and one I2C temperature sensor
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
The SSP0/SPI1 and SSP1/SPI2 shared pinout and should be disable by
default.
Board specific dts should enable them, as needed.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Preparatory change prior to disabling SSPx controllers
by default in the shared LPC32xx DTSI file.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change adds clock properties to spi peripheral devices,
clock ids are taken from dt-bindings/clock/lpc32xx-clock.h
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Taken from the datasheet.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for battery level reading on the Nexus7 by
enabling the bq27541 driver in the nexus7 dts
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Vinay Simha BN <simhavcs@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds support to on board LIS3MDLTR magnetometer.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds spi nodes required to provide spi bus support on LS
expansion.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds nodes required to enable 4 i2c buses on the board which
are connected to various sensors and eeprom.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds support to 4 user leds, wlan and bt led on board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch enables sata and regulators required to get on board sata
working.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds pcie and regulators required to get on board ATL1C
ethernet working.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
