| Age | Commit message (Collapse) | Author |
|---|
|
NXP LPC32xx has three interrupt controllers, namely root Main
Interrupt Controller (MIC) and two supplementary Sub Interrupt
Controllers (SIC1 and SIC2), four interrupt outputs from SIC1 and SIC2
are connected to MIC.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Fix gpio active flag for the phy reset-gpios property. The line is
active low instead of active high.
Actually, this flags was never used by the macb driver.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
As the watchdog timer needs the slow clock, add it to the currently defined
wdt node.
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add the SAMA5D2-Compatible Shutdown Controller node to sama5d2.dtsi
and the use of it in the sama5d2 Xplained board dts file.
Enable the RTC wakeup event and the "wake up" button support through the
input "0" that is present on the board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The "interrupts" property is missing from the watchdog node. Add it with
highest priority value of 7.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
There is no external dependency for Security SubSystem (SSS) block so
the nodes for Pseudo Random Number Generator and AES hardware
acceleration can be enabled always for all Exynos4 devices.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch changes the compatible of Exynos5420 fimd
to "exynos5420-fimd". To support MIC bypass from display
path, the new compatible is introduced for Exynos5420.
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Exynos5420 boards
The bindings like s2mps11,buck6-ramp-enable or s2mps11,buck2-ramp-delay
were ignored. They were never parsed by s2mps11 regulator driver. Also
the values used in these bindings were equal to default reset values of
S2MPS11 device. It is safe to remove them.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Embest MarS Board [1] is a multi-core platform based on Freescale i.MX6
Cortex-A9 Dual Core, running up to 1GHz with 1 GB of RAM, 4GB of eMMC
and with a 4MB SPI flash.
[1] http://www.embest-tech.com/shop/star/marsboard.html
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Introduce am335x-baltos.dtsi, that provides common configuration
for the whole device family based on the same SODIMM module.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DRA7 family of processors from Texas Instruments, have a hardware module
called IODELAYCONFIG Module which is expected to be configured. This
block allows very specific custom fine tuning for electrical
characteristics of IO pins that are necessary for functionality and
device lifetime requirements. IODelay module has it's own register space
with registers to configure various pins.
According to AM572x TRM SPRUHZ6E October 2014–Revised January 2016[1]
section 18.4.6.1 Pad Configuration, in addition to pinmuxing(MUXMODE),
when operating a pad in certain mode, Virtual/Manual IO Timing Mode must
also be configured to ensure that IO timings are met (DELAYMODE and
MODESELECT fields of pad's IODELAYCONFIG module register). According to
section 18.4.6.1.7 Isolation Requirements of above TRM, when
reprogramming MUXMODE, DELAYMODE, and MODESELECT fields, there is a
potential for a significant glitch on the corresponding IO. It is hence
recommended to do this with I/O isolation (which can only be done in
initial stages of bootloader). QSPI is one such module that requires
IODELAY configuration. So, this patch removes the pinmux for
QSPI for DRA74/DRA72 EVM as it needs to be done in bootloader (U-Boot)
and cannot be done in kernel.
Users should migrate to U-Boot v2016.05-rc1 or higher.
[1] http://www.ti.com/lit/ug/spruhz6e/spruhz6e.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
tested on OMP5432 EVM
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
tested on Pandaboard ES.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The boards use a TI variant of the PCF8575 so specify that
in the compatible string.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per the data sheet starting from SPRUHQ0H (Nov 2015 - Latest[1]),
VDD_CORE can vary from 0.85v to 1.15v for AVS class0. VDD GPU/DSP
et.al. can range from 0.85v to 1.25V with AVS class0
Since dynamic voltage scaling is disabled for DRA7/AM57xx SoCs for
all SoC rails other than MPU, the bootloader is responsible for
setting up the AVS class0 voltage, however, with wrong voltage machine
constraints in dtb, regulator framework will lower the voltage below
the required voltage levels for certain samples in production flow.
This can cause catastrophic failures which can be pretty hard to
identify.
Update board files which don't match required specification.
[1] http://www.ti.com/product/AM5728/datasheet/specifications#SPRT637-7340
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This aligns with the internal configuration.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
obtaining DMA memory
Doing so saves quite a bit of code in the driver.
For more information on the 'reserved-memory' bindings see:
Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
This patch supplies the Mailbox Controller nodes. In order to
request channels, these nodes will be referenced by Mailbox
Client nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
This is used for CPU Frequency Scaling.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Used for Voltage Scaling using CPUFreq.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
You'll notice that the voltage cell is populated with 0's. Voltage
information is very platform specific, even depends on 'cut' and
'substrate' versions. Thus it is left blank for a generic (safe)
implementation. If other nodes/properties are provided by the
bootloader, the ST CPUFreq driver will over-ride these generic
values.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
When compiled with "W=1", dtc complains: e.g.
"Warning (unit_address_vs_reg):
Node /soc/ipu@02800000/port@2/endpoint@0
has a unit name, but no reg property"
Endpoint nodes don't have a reg property, and the addresses
in their node names are ordinals without any special meaning
so remove them and swap them for semantic node names.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Table 8 from MX6DL datasheet (IMX6SDLCEC Rev. 5, 06/2015):
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SDLCEC.pdf
states the following:
"LDO Output Set Point (VDD_ARM_CAP) = 1.125 V minimum for operation
up to 396 MHz."
So fix the entry by adding the 25mV margin value as done in the other
entries of the table, which results in 1.15V for 396MHz operation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
198MHz is a valid operating point for mx6sx.
Add entries for VDD_ARM_CAP and VDD_SOC_CAP voltages for 198MHz according
to the imx6sx datahseet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SXIEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
These values also match the ones from the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adjust the VDD_ARM_CAP and VDD_SOC_CAP voltages according to
Table-11 from MX6UL datasheet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6ULCEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
into next/dt
Merge "ARM: dts: Add OXNAS Platform Bindings" from Neil Armstrong:
* tag 'ox810se-arm-dt-v4.6-rc3' of https://github.com/superna9999/linux:
ARM: boot: dts: Add Western Digital My Book World Edition device tree
dt-bindings: Add Western Digital to vendor prefixes
dt-bindings: Add OXNAS bindings
ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi
dt-bindings: Add Oxford Semiconductor to vendor prefixes
dt-bindings: irq: arm,versatile-fpga: add compatible string for OX810SE SoC
|
|
Application Notes 399 and 400 shares the same memory map and
features. Both are shipped with Cortex-M7 and have the same peripheral
as AN385/AN386, but with different location of PSRAM and Ethernet
controller.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Application Notes 385 and 386 shares the same memory map and features
except the CPU is used. AN385 is supplied with Cortex-M3 CPU and AN386
is supplied with Cortex-M4.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
This is a backmerge of v4.6 fixes, to avoid a merge conflict between 4.6
and our next/dt branch.
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
|
|
Fix a typo on PIN_PD24 for UTXD2 and FLEXCOM4_IO3 which were
wrongly linked to PIN_PD23).
Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Fixes: 7f16cb676c00 ("ARM: at91/dt: add sama5d2 pinmux")
Cc: stable@vger.kernel.org # v4.4+
[nicolas.ferre@atmel.com: add commit message, changed subject]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add Western Digital My Book World Edition device tree based on
Oxford Semiconductor OX810SE SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Under the OX810SE, this same controller is used as "Reference Peripheral
Specification" Interrupt Controller, so add new compatible string to support
the Oxford Semiconductor OX810SE SoC Interrupt Controller.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
