| Age | Commit message (Collapse) | Author |
|---|
|
Added support for 1000BASE-BX, i.e. Gigabit Ethernet over single strand
of single-mode fiber.
The initialization of a 1000BASE-BX SFP is the same as 1000BASE-SX/LX
with the only difference that the Bit Rate Nominal Value must be
checked to make sure it is a Gigabit Ethernet transceiver, as described
by the SFF-8472 specification.
This was tested with the FS.com SFP-GE-BX 1310/1490nm 10km transceiver:
$ ethtool -m eth4
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x40 0x00 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: BASE-BX10
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 10km
Length (SMF) : 10000m
Length (50um) : 0m
Length (62.5um) : 0m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 1310nm
Vendor name : FS
Vendor OUI : 64:9d:99
Vendor PN : SFP-GE-BX
Vendor rev :
Option values : 0x20 0x0a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : Power level 3 requirement
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : S2202359108
Date code : 220307
Optical diagnostics support : Yes
Laser bias current : 17.650 mA
Laser output power : 0.2132 mW / -6.71 dBm
Receiver signal average optical power : 0.2740 mW / -5.62 dBm
Module temperature : 47.30 degrees C / 117.13 degrees F
Module voltage : 3.2576 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : Off
Laser rx power high warning : Off
Laser rx power low warning : Off
Laser bias current high alarm threshold : 110.000 mA
Laser bias current low alarm threshold : 1.000 mA
Laser bias current high warning threshold : 100.000 mA
Laser bias current low warning threshold : 1.000 mA
Laser output power high alarm threshold : 0.7079 mW / -1.50 dBm
Laser output power low alarm threshold : 0.0891 mW / -10.50 dBm
Laser output power high warning threshold : 0.6310 mW / -2.00 dBm
Laser output power low warning threshold : 0.1000 mW / -10.00 dBm
Module temperature high alarm threshold : 90.00 degrees C / 194.00 degrees F
Module temperature low alarm threshold : -45.00 degrees C / -49.00 degrees F
Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
Module temperature low warning threshold : -40.00 degrees C / -40.00 degrees F
Module voltage high alarm threshold : 3.7950 V
Module voltage low alarm threshold : 2.8050 V
Module voltage high warning threshold : 3.4650 V
Module voltage low warning threshold : 3.1350 V
Laser rx power high alarm threshold : 0.7079 mW / -1.50 dBm
Laser rx power low alarm threshold : 0.0028 mW / -25.53 dBm
Laser rx power high warning threshold : 0.6310 mW / -2.00 dBm
Laser rx power low warning threshold : 0.0032 mW / -24.95 dBm
Signed-off-by: Ernesto Castellotti <ernesto@castellotti.net>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Linux users sometimes need an easy way to check current values of module
parameters. For example the module may be manually reloaded with different
parameters. Make these visible and readable in the /sys filesystem to allow
that. But don't make the "debug" module parameter visible as debugging is
enabled via ethtool msglvl.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stephen Rothwell and kernel test robot reported that some arches
(parisc, hexagon) and/or compilers would not like blamed commit.
Lets make sure tcp_sock_write_rx group does not start with a hole.
While we are at it, correct tcp_sock_write_tx CACHELINE_ASSERT_GROUP_SIZE()
since after the blamed commit, we went to 105 bytes.
Fixes: 99123622050f ("tcp: remove some holes in struct tcp_sock")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/netdev/20240301121108.5d39e4f9@canb.auug.org.au/
Closes: https://lore.kernel.org/oe-kbuild-all/202403011451.csPYOS3C-lkp@intel.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20240301171945.2958176-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Based on the static analyzis of the code it looks like when an entry
from the MAC table was removed, the entry was still used after being
freed. More precise the vid of the mac_entry was used after calling
devm_kfree on the mac_entry.
The fix consists in first using the vid of the mac_entry to delete the
entry from the HW and after that to free it.
Fixes: b37a1bae742f ("net: sparx5: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240301080608.3053468-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Also remove related log messages.
Signed-off-by: Matthew Sakai <msakai@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Remove obsolete function vdo_perform_once. Instead, initialize
necessary module state when loading the module.
Signed-off-by: Matthew Sakai <msakai@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Add the dependsOn test check for all the mirred blockcast tests.
It will prevent the issue reported by LKFT which happens when an older
iproute2 is used to run the current tdc.
Tests are skipped if the dependsOn check fails.
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Link: https://lore.kernel.org/r/20240229143825.1373550-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Changes :
- "excercise" is corrected to "exercise" in drivers/net/mlxsw/spectrum-2/tc_flower.sh
- "mutliple" is corrected to "multiple" in drivers/net/netdevsim/ethtool-fec.sh
Signed-off-by: Prabhav Kumar Vaish <pvkumar5749404@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240228120701.422264-1-pvkumar5749404@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We will save allocated tag in the object header to indicate that it's
allocated.
handle |= OBJ_ALLOCATED_TAG;
So the object header needs to reserve LSB for this tag bit.
But the handle itself doesn't need to reserve LSB to save tag, since it's
only used to find the position of object, by (pfn + obj_idx). So remove
LSB reserve from handle, one more bit can be used as obj_idx.
Link: https://lkml.kernel.org/r/20240228023854.3511239-1-chengming.zhou@linux.dev
Signed-off-by: Chengming Zhou <chengming.zhou@linux.dev>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Yosry Ahmed <yosryahmed@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
do_numa_page() is reading from the same page table entry, twice, while
holding the page table lock: once while checking that the pte hasn't
changed, and again in order to modify the pte.
Instead, just read the pte once, and save it in the same old_pte variable
that already exists. This has no effect on behavior, other than to
provide a tiny potential improvement to performance, by avoiding the
redundant memory read (which the compiler cannot elide, due to
READ_ONCE()).
Also improve the associated comments nearby.
Link: https://lkml.kernel.org/r/20240228034151.459370-1-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
alloc_contig_migrate_range has every information to be able to understand
big contiguous allocation latency. For example, how many pages are
migrated, how many times they were needed to unmap from page tables.
This patch adds the trace event to collect the allocation statistics. In
the field, it was quite useful to understand CMA allocation latency.
[akpm@linux-foundation.org: a/trace_mm_alloc_config_migrate_range_info_enabled/trace_mm_alloc_contig_migrate_range_info_enabled]
Link: https://lkml.kernel.org/r/20240228051127.2859472-1-richardycc@google.com
Signed-off-by: Richard Chang <richardycc@google.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org.
Cc: Martin Liu <liumartin@google.com>
Cc: "Masami Hiramatsu (Google)" <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We already have a folio; use it instead of the head page where reasonable.
Saves a couple of calls to compound_head() and elimimnates a few
references to page->mapping.
Link: https://lkml.kernel.org/r/20240228164326.1355045-1-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
In memory_model.h, if CONFIG_SPARSEMEM_VMEMMAP is configed, kernel will
use vmemmap to do the __pfn_to_page/page_to_pfn, and kernel will not use
the "classic sparse" to do the __pfn_to_page/page_to_pfn.
So export the vmemmap when CONFIG_SPARSEMEM_VMEMMAP is configed. This
makes the user applications (crash, etc) get faster
pfn_to_page/page_to_pfn operations too.
Link: https://lkml.kernel.org/r/20240227014952.3184-1-shijie@os.amperecomputing.com
Signed-off-by: Huang Shijie <shijie@os.amperecomputing.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Kazuhito Hagio <k-hagio-ab@nec.com>
Cc: Lianbo Jiang <lijiang@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The synchronization here is to ensure the ordering of freeing of a module
init so that it happens before W+X checking. It is worth noting it is not
that the freeing was not happening, it is just that our sanity checkers
raced against the permission checkers which assume init memory is already
gone.
Commit 1a7b7d922081 ("modules: Use vmalloc special flag") moved calling
do_free_init() into a global workqueue instead of relying on it being
called through call_rcu(..., do_free_init), which used to allowed us call
do_free_init() asynchronously after the end of a subsequent grace period.
The move to a global workqueue broke the gaurantees for code which needed
to be sure the do_free_init() would complete with rcu_barrier(). To fix
this callers which used to rely on rcu_barrier() must now instead use
flush_work(&init_free_wq).
Without this fix, we still could encounter false positive reports in W+X
checking since the rcu_barrier() here can not ensure the ordering now.
Even worse, the rcu_barrier() can introduce significant delay. Eric
Chanudet reported that the rcu_barrier introduces ~0.1s delay on a
PREEMPT_RT kernel.
[ 0.291444] Freeing unused kernel memory: 5568K
[ 0.402442] Run /sbin/init as init process
With this fix, the above delay can be eliminated.
Link: https://lkml.kernel.org/r/20240227023546.2490667-1-changbin.du@huawei.com
Fixes: 1a7b7d922081 ("modules: Use vmalloc special flag")
Signed-off-by: Changbin Du <changbin.du@huawei.com>
Tested-by: Eric Chanudet <echanude@redhat.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Xiaoyi Su <suxiaoyi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
All but one caller already has a folio, so convert
free_page_and_swap_cache() to have a folio and remove the call to
page_folio().
Link: https://lkml.kernel.org/r/20240227174254.710559-19-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
These pages are all chained together through the lru list, so we know
they're folios. Use the folio APIs to save three hidden calls to
compound_head().
Link: https://lkml.kernel.org/r/20240227174254.710559-18-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Process the pages in batch-sized quantities instead of all-at-once.
Link: https://lkml.kernel.org/r/20240227174254.710559-17-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The last user was removed over a year ago; remove the definition.
Link: https://lkml.kernel.org/r/20240227174254.710559-16-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
All callers now use free_unref_folios() so we can delete this function.
Link: https://lkml.kernel.org/r/20240227174254.710559-15-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
All users have been converted to mem_cgroup_uncharge_folios() so we can
remove this API.
Link: https://lkml.kernel.org/r/20240227174254.710559-14-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The few folios which can't be moved to the LRU list (because their
refcount dropped to zero) used to be returned to the caller to dispose of.
Make this simpler to call by freeing the folios directly through
free_unref_folios().
Link: https://lkml.kernel.org/r/20240227174254.710559-13-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Use free_unref_page_batch() to free the folios. This may increase the
number of IPIs from calling try_to_unmap_flush() more often, but that's
going to be very workload-dependent. It may even reduce the number of
IPIs as we now batch-free large folios instead of freeing them one at a
time.
Link: https://lkml.kernel.org/r/20240227174254.710559-12-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Hugetlb folios still get special treatment, but normal large folios can
now be freed by free_unref_folios(). This should have a reasonable
performance impact, TBD.
Link: https://lkml.kernel.org/r/20240227174254.710559-11-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Call folio_undo_large_rmappable() if needed. free_unref_page_prepare()
destroys the ability to call folio_order(), so stash the order in
folio->private for the benefit of the second loop.
Link: https://lkml.kernel.org/r/20240227174254.710559-10-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Pass a pointer to the lruvec so we can take advantage of the
folio_lruvec_relock_irqsave(). Adjust the calling convention of
folio_lruvec_relock_irqsave() to suit and add a page_cache_release()
wrapper.
Link: https://lkml.kernel.org/r/20240227174254.710559-9-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Break up the list of folios into batches here so that the folios are more
likely to be cache hot when doing the rest of the processing.
Link: https://lkml.kernel.org/r/20240227174254.710559-8-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Instead of putting the interesting folios on a list, delete the
uninteresting one from the folio_batch.
Link: https://lkml.kernel.org/r/20240227174254.710559-7-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Almost identical to mem_cgroup_uncharge_list(), except it takes a
folio_batch instead of a list_head.
Link: https://lkml.kernel.org/r/20240227174254.710559-6-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
There's no need to indirect through release_pages() and iterate over this
batch of folios an extra time; we can just use the batch that we have.
Link: https://lkml.kernel.org/r/20240227174254.710559-5-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Iterate over a folio_batch rather than a linked list. This is easier for
the CPU to prefetch and has a batch count naturally built in so we don't
need to track it. Again, this lowers the maximum lock hold time from
32 folios to 15, but I do not expect this to have a significant effect.
Link: https://lkml.kernel.org/r/20240227174254.710559-4-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Most of its callees are not yet ready to accept a folio, but we know all
of the pages passed in are actually folios because they're linked through
->lru.
Link: https://lkml.kernel.org/r/20240227174254.710559-3-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "Rearrange batched folio freeing", v3.
Other than the obvious "remove calls to compound_head" changes, the
fundamental belief here is that iterating a linked list is much slower
than iterating an array (5-15x slower in my testing). There's also an
associated belief that since we iterate the batch of folios three times,
we do better when the array is small (ie 15 entries) than we do with a
batch that is hundreds of entries long, which only gives us the
opportunity for the first pages to fall out of cache by the time we get to
the end.
It is possible we should increase the size of folio_batch. Hopefully the
bots let us know if this introduces any performance regressions.
This patch (of 3):
By making release_pages() call folios_put(), we can get rid of the calls
to compound_head() for the callers that already know they have folios. We
can also get rid of the lock_batch tracking as we know the size of the
batch is limited by folio_batch. This does reduce the maximum number of
pages for which the lruvec lock is held, from SWAP_CLUSTER_MAX (32) to
PAGEVEC_SIZE (15). I do not expect this to make a significant difference,
but if it does, we can increase PAGEVEC_SIZE to 31.
Link: https://lkml.kernel.org/r/20240227174254.710559-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20240227174254.710559-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Previously, we removed the mm from mm_slot and dropped mm_count
if the MMF_THP_DISABLE flag was set. However, we didn't re-add
the mm back after clearing the MMF_THP_DISABLE flag. Additionally,
We add a check for the MMF_THP_DISABLE flag in hugepage_vma_revalidate().
Link: https://lkml.kernel.org/r/20240227035135.54593-1-ioworker0@gmail.com
Fixes: 879c6000e191 ("mm/khugepaged: bypassing unnecessary scans with MMF_DISABLE_THP check")
Signed-off-by: Lance Yang <ioworker0@gmail.com>
Suggested-by: Yang Shi <shy828301@gmail.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Use an unsigned long constant instead of an int constant and a cast. This
fixes the checkpatch warning
WARNING: Unnecessary typecast of c90 int constant - '(unsigned long) 1' could be '1UL'
+ align = ((unsigned long) 1) << i;
Link: https://lkml.kernel.org/r/20240226191159.39509-4-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The module is never loaded successfully. Therefore, it'll never be
unloaded and we can remove the exit function.
Link: https://lkml.kernel.org/r/20240226191159.39509-3-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Fix a typo and change the function name to init_test_configuration. Both
caller and definition have the same typo, so the current code already
works.
Link: https://lkml.kernel.org/r/20240226191159.39509-2-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
All users of total_mapcount() are gone, let's remove it.
Link: https://lkml.kernel.org/r/20240226141324.278526-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "mm: remove total_mapcount()", v2.
Let's remove the remaining user from mm/memfd.c so we can get rid of
total_mapcount().
This patch (of 2):
Both functions are the remaining users of total_mapcount(). Let's get rid
of the calls by converting the code to folios.
As it turns out, the code is unnecessarily complicated, especially:
1) We can query the number of pagecache references for a folio simply via
folio_nr_pages(). This will handle other folio sizes in the future
correctly.
2) The xas_set(xas, page->index + cache_count) call to increment the
iterator for large folios is not required. Remove it.
Further, simplify the XA_CHECK_SCHED check, counting each entry exactly
once.
Memfd pages can be swapped out when using shmem; leave xa_is_value()
checks in place.
Link: https://lkml.kernel.org/r/20240226141324.278526-1-david@redhat.com
Link: https://lkml.kernel.org/r/20240226141324.278526-2-david@redhat.com
Co-developed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
It is used to test split_huge_page_to_list_to_order for pagecache THPs.
Also add test cases for split_huge_page_to_list_to_order via both debugfs.
[ziy@nvidia.com: fix issue discovered with NFS]
Link: https://lkml.kernel.org/r/262E4DAA-4A78-4328-B745-1355AE356A07@nvidia.com
Link: https://lkml.kernel.org/r/20240226205534.1603748-9-zi.yan@sent.com
Signed-off-by: Zi Yan <ziy@nvidia.com>
Tested-by: Aishwarya TCV <aishwarya.tcv@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Cc: Aishwarya TCV <aishwarya.tcv@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
To split a THP to any lower order pages, we need to reform THPs on
subpages at given order and add page refcount based on the new page order.
Also we need to reinitialize page_deferred_list after removing the page
from the split_queue, otherwise a subsequent split will see list
corruption when checking the page_deferred_list again.
Note: Anonymous order-1 folio is not supported because _deferred_list,
which is used by partially mapped folios, is stored in subpage 2 and an
order-1 folio only has subpage 0 and 1. File-backed order-1 folios are
fine, since they do not use _deferred_list.
[ziy@nvidia.com: fixup per discussion with Ryan]
Link: https://lkml.kernel.org/r/494F48CD-1F0F-4CAD-884E-6D48F40AF990@nvidia.com
Link: https://lkml.kernel.org/r/20240226205534.1603748-8-zi.yan@sent.com
Signed-off-by: Zi Yan <ziy@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
It adds a new_order parameter to set new page order in page owner. It
prepares for upcoming changes to support split huge page to any lower
order.
Link: https://lkml.kernel.org/r/20240226205534.1603748-7-zi.yan@sent.com
Signed-off-by: Zi Yan <ziy@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
It sets memcg information for the pages after the split. A new parameter
new_order is added to tell the order of subpages in the new page, always 0
for now. It prepares for upcoming changes to support split huge page to
any lower order.
Link: https://lkml.kernel.org/r/20240226205534.1603748-6-zi.yan@sent.com
Signed-off-by: Zi Yan <ziy@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We do not have non power of two pages, using nr is error prone if nr is
not power-of-two. Use page order instead.
Link: https://lkml.kernel.org/r/20240226205534.1603748-5-zi.yan@sent.com
Signed-off-by: Zi Yan <ziy@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We do not have non power of two pages, using nr is error prone if nr is
not power-of-two. Use page order instead.
Link: https://lkml.kernel.org/r/20240226205534.1603748-4-zi.yan@sent.com
Signed-off-by: Zi Yan <ziy@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Folios of order 1 have no space to store the deferred list. This is not a
problem for the page cache as file-backed folios are never placed on the
deferred list. All we need to do is prevent the core MM from touching the
deferred list for order 1 folios and remove the code which prevented us
from allocating order 1 folios.
Link: https://lore.kernel.org/linux-mm/90344ea7-4eec-47ee-5996-0c22f42d6a6a@google.com/
Link: https://lkml.kernel.org/r/20240226205534.1603748-3-zi.yan@sent.com
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Zi Yan <ziy@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "Split a folio to any lower order folios", v5.
File folio supports any order and multi-size THP is upstreamed[1], so both
file and anonymous folios can be >0 order. Currently, split_huge_page()
only splits a huge page to order-0 pages, but splitting to orders higher
than 0 might better utilize large folios, if done properly. In addition,
Large Block Sizes in XFS support would benefit from it during truncate[2].
This patchset adds support for splitting a large folio to any lower order
folios.
In addition to this implementation of split_huge_page_to_list_to_order(),
a possible optimization could be splitting a large folio to arbitrary
smaller folios instead of a single order. As both Hugh and Ryan pointed
out [3,5] that split to a single order might not be optimal, an order-9
folio might be better split into 1 order-8, 1 order-7, ..., 1 order-1, and
2 order-0 folios, depending on subsequent folio operations. Leave this as
future work.
[1] https://lore.kernel.org/all/20231207161211.2374093-1-ryan.roberts@arm.com/
[2] https://lore.kernel.org/linux-mm/20240226094936.2677493-1-kernel@pankajraghav.com/
[3] https://lore.kernel.org/linux-mm/9dd96da-efa2-5123-20d4-4992136ef3ad@google.com/
[4] https://lore.kernel.org/linux-mm/cbb1d6a0-66dd-47d0-8733-f836fe050374@arm.com/
[5] https://lore.kernel.org/linux-mm/20240213215520.1048625-1-zi.yan@sent.com/
This patch (of 8):
As multi-size THP support is added, not all THPs are PMD-mapped, thus
during a huge page split, there is no need to always split PMD mapping in
unmap_folio(). Make it conditional.
Link: https://lkml.kernel.org/r/20240226205534.1603748-1-zi.yan@sent.com
Link: https://lkml.kernel.org/r/20240226205534.1603748-2-zi.yan@sent.com
Signed-off-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Koutny <mkoutny@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Introduce GFP bits enumeration to let compiler track the number of used
bits (which depends on the config options) instead of hardcoding them.
That simplifies __GFP_BITS_SHIFT calculation.
Link: https://lkml.kernel.org/r/20240224015800.2569851-1-surenb@google.com
Suggested-by: Petr Tesařík <petr@tesarici.cz>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Petr Tesarik <petr@tesarici.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
While doing MADV_PAGEOUT, the current code will clear PTE young so that
vmscan won't read young flags to allow the reclamation of madvised folios
to go ahead. It seems we can do it by directly ignoring references, thus
we can remove tlb flush in madvise and rmap overhead in vmscan.
Regarding the side effect, in the original code, if a parallel thread runs
side by side to access the madvised memory with the thread doing madvise,
folios will get a chance to be re-activated by vmscan (though the time gap
is actually quite small since checking PTEs is done immediately after
clearing PTEs young). But with this patch, they will still be reclaimed.
But this behaviour doing PAGEOUT and doing access at the same time is
quite silly like DoS. So probably, we don't need to care. Or ignoring
the new access during the quite small time gap is even better.
For DAMON's DAMOS_PAGEOUT based on physical address region, we still keep
its behaviour as is since a physical address might be mapped by multiple
processes. MADV_PAGEOUT based on virtual address is actually much more
aggressive on reclamation. To untouch paddr's DAMOS_PAGEOUT, we simply
pass ignore_references as false in reclaim_pages().
A microbench as below has shown 6% decrement on the latency of
MADV_PAGEOUT,
#define PGSIZE 4096
main()
{
int i;
#define SIZE 512*1024*1024
volatile long *p = mmap(NULL, SIZE, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS, -1, 0);
for (i = 0; i < SIZE/sizeof(long); i += PGSIZE / sizeof(long))
p[i] = 0x11;
madvise(p, SIZE, MADV_PAGEOUT);
}
w/o patch w/ patch
root@10:~# time ./a.out root@10:~# time ./a.out
real 0m49.634s real 0m46.334s
user 0m0.637s user 0m0.648s
sys 0m47.434s sys 0m44.265s
Link: https://lkml.kernel.org/r/20240226005739.24350-1-21cnbao@gmail.com
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: SeongJae Park <sj@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Make clear the atmicity/consistency requirements of the API and how we
achieve them.
Link: https://lore.kernel.org/linux-mm/Zc-Tqqfksho3BHmU@arm.com/
Link: https://lkml.kernel.org/r/20240226120321.1055731-3-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "Address some contpte nits".
These 2 patches address some nits raised by Catalin late in the review cycle for
my contpte series [1].
[1] https://lore.kernel.org/linux-mm/20240215103205.2607016-1-ryan.roberts@arm.com/
This patch (of 2):
The contpte symbols must be exported since some of the public inline
ptep_* APIs are called from modules and these inlines now call the contpte
functions. Originally they were exported as EXPORT_SYMBOL() for fear of
breaking out-of-tree modules. But we subsequently concluded that
EXPORT_SYMBOL_GPL() should be safe since these functions are deeply core
mm routines, and any module operating at this level is not going to be
able to survive on EXPORT_SYMBOL alone.
Link: https://lkml.kernel.org/r/20240226120321.1055731-1-ryan.roberts@arm.com
Link: https://lore.kernel.org/linux-mm/f9fc2b31-11cb-4969-8961-9c89fea41b74@nvidia.com/
Link: https://lkml.kernel.org/r/20240226120321.1055731-2-ryan.roberts@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
