| Age | Commit message (Collapse) | Author |
|---|
|
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.
Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.
Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.
Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit ad260ab32a4d94fa974f58262f8000472d34fd5b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Two commits to fix the following subtle cgroup2 behavior bugs:
- cpu.max was rejecting config when it shouldn't
- thread mode enable was allowed when it shouldn't"
* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix rule checking for threaded mode switching
sched, cgroup: Don't reject lower cpu.max on ancestors
|
|
The resource allocation in WDAT watchdog has off-one-by error, it sets
one byte more than the actual end address. This may eventually lead
to unexpected resource conflicts.
Fixes: 058dfc767008 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"Two low-impact workqueue commits.
One fixes workqueue creation error path and the other removes the
unused cancel_work()"
* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove unused cancel_work()
workqueue: use put_device() instead of kfree()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fixes from Tejun Heo:
"Late percpu pull request for v4.16-rc6.
- percpu allocator pool replenishing no longer triggers OOM or
warning messages.
Also, the alloc interface now understands __GFP_NORETRY and
__GFP_NOWARN. This is to allow avoiding OOMs from userland
triggered actions like bpf map creation.
Also added cond_resched() in alloc loop.
- perpcu allocation now can be interrupted by kill sigs to avoid
deadlocking OOM killer.
- Added Dennis Zhou as a co-maintainer.
He has rewritten the area map allocator, understands most of the
code base and has been responsive for all bug reports"
* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu_ref: Update doc to dissuade users from depending on internal RCU grace periods
mm: Allow to kill tasks doing pcpu_alloc() and waiting for pcpu_balance_workfn()
percpu: include linux/sched.h for cond_resched()
percpu: add a schedule point in pcpu_balance_workfn()
percpu: allow select gfp to be passed to underlying allocators
percpu: add __GFP_NORETRY semantics to the percpu balancing path
percpu: match chunk allocator declarations with definitions
percpu: add Dennis Zhou as a percpu co-maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"I sat on them too long and it's quite a few this late, but nothing has
a wide blast area. The changes are...
- Fix corner cases in SG command handling.
- Recent introduction of default powersaving mode config option
exposed several devices with broken powersaving behaviors. A number
of patches to update the blacklist accordingly.
- Fix a kernel panic on SAS hotplug.
- Other misc and device specific updates"
* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Modify quirks for MX100 to limit NCQ_TRIM quirk to MU01 version
libata: Make Crucial BX100 500GB LPM quirk apply to all firmware versions
libata: Apply NOLPM quirk to Crucial M500 480 and 960GB SSDs
libata: Enable queued TRIM for Samsung SSD 860
PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L
ahci: Add PCI-id for the Highpoint Rocketraid 644L card
ata: do not schedule hot plug if it is a sas host
libata: disable LPM for Crucial BX100 SSD 500GB drive
libata: Apply NOLPM quirk to Crucial MX100 512GB SSDs
libata: update documentation for sysfs interfaces
ata: sata_rcar: Remove unused variable in sata_rcar_init_controller()
libata: transport: cleanup documentation of sysfs interface
sata_rcar: Reset SATA PHY when Salvator-X board resumes
libata: don't try to pass through NCQ commands to non-NCQ devices
libata: remove WARN() for DMA or PIO command without data
libata: fix length validation of ATAPI-relayed SCSI commands
ata: libahci: fix comment indentation
ahci: Add check for device presence (PCIe hot unplug) in ahci_stop_engine()
libata: Fix compile warning with ATA_DEBUG enabled
|
|
We had some reports of panics in nfsd4_lm_notify, and that showed a
nfs4_lockowner that had outlived its so_client.
Ensure that we walk any leftover lockowners after tearing down all of
the stateids, and remove any blocked locks that they hold.
With this change, we also don't need to walk the nbl_lru on nfsd_net
shutdown, as that will happen naturally when we tear down the clients.
Fixes: 76d348fadff5 (nfsd: have nfsd4_lock use blocking locks for v4.1+ locks)
Reported-by: Frank Sorenson <fsorenso@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@vger.kernel.org # 4.9
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
XRCD object is not implemented in the restrack, so lets remove it.
Fixes: 02d8883f520e ("RDMA/restrack: Add general infrastructure to track RDMA resources")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The error in ucma_create_id() left ctx in the list of contexts belong
to ucma file descriptor. The attempt to close this file descriptor causes
to use-after-free accesses while iterating over such list.
Fixes: 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
Reported-by: <syzbot+dcfd344365a56fbebd0f@syzkaller.appspotmail.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
grace periods
percpu_ref internally uses sched-RCU to implement the percpu -> atomic
mode switching and the documentation suggested that this could be
depended upon. This doesn't seem like a good idea.
* percpu_ref uses sched-RCU which has different grace periods regular
RCU. Users may combine percpu_ref with regular RCU usage and
incorrectly believe that regular RCU grace periods are performed by
percpu_ref. This can lead to, for example, use-after-free due to
premature freeing.
* percpu_ref has a grace period when switching from percpu to atomic
mode. It doesn't have one between the last put and release. This
distinction is subtle and can lead to surprising bugs.
* percpu_ref allows starting in and switching to atomic mode manually
for debugging and other purposes. This means that there may not be
any grace periods from kill to release.
This patch makes it clear that the grace periods are percpu_ref's
internal implementation detail and can't be depended upon by the
users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In case of memory deficit and low percpu memory pages,
pcpu_balance_workfn() takes pcpu_alloc_mutex for a long
time (as it makes memory allocations itself and waits
for memory reclaim). If tasks doing pcpu_alloc() are
choosen by OOM killer, they can't exit, because they
are waiting for the mutex.
The patch makes pcpu_alloc() to care about killing signal
and use mutex_lock_killable(), when it's allowed by GFP
flags. This guarantees, a task does not miss SIGKILL
from OOM killer.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
microblaze build broke due to missing declaration of the
cond_resched() invocation added recently. Let's include linux/sched.h
explicitly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
|
|
CM_PLLx and A2W_XOSC_CTRL registers are accessed by different clock
handlers and must be accessed with ->regs_lock held.
Update the sections where this protection is missing.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
ana->maskX values are already '~'-ed in bcm2835_pll_set_rate(). Remove
the '~' in the definition to fix ANA setup.
Note that this commit fixes a long standing bug preventing one from
using an HDMI display if it's plugged after the FW has booted Linux.
This is because PLLH is used by the HDMI encoder to generate the pixel
clock.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch fixes static checker warning caused by
"36cc549d5986: "drm/amd/display: disable CRTCs with
NULL FB on their primary plane (V2)"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
bad case won't follow normal sense, it will not enable vga1 as usual, but vga2,3,4 is on.
Signed-off-by: Clark Zheng <clark.zheng@amd.com>
Reviewed-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently, the offsets in the UAC2 processing unit descriptor are
calculated incorrectly. It causes an issue when connecting the device which
provides such a feature:
~~~~
[84126.724420] usb 1-1.3.1: invalid Processing Unit descriptor (id 18)
~~~~
After this patch is applied, the UAC2 processing unit inits w/o this error.
Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When commit 9c7be59fc519af ("libata: Apply NOLPM quirk to Crucial MX100
512GB SSDs") was added it inherited the ATA_HORKAGE_NO_NCQ_TRIM quirk
from the existing "Crucial_CT*MX100*" entry, but that entry sets model_rev
to "MU01", where as the entry adding the NOLPM quirk sets it to NULL.
This means that after this commit we no apply the NO_NCQ_TRIM quirk to
all "Crucial_CT512MX100*" SSDs even if they have the fixed "MU02"
firmware. This commit splits the "Crucial_CT512MX100*" quirk into 2
quirks, one for the "MU01" firmware and one for all other firmware
versions, so that we once again only apply the NO_NCQ_TRIM quirk to the
"MU01" firmware version.
Fixes: 9c7be59fc519af ("libata: Apply NOLPM quirk to ... MX100 512GB SSDs")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Commit b17e5729a630 ("libata: disable LPM for Crucial BX100 SSD 500GB
drive"), introduced a ATA_HORKAGE_NOLPM quirk for Crucial BX100 500GB SSDs
but limited this to the MU02 firmware version, according to:
http://www.crucial.com/usa/en/support-ssd-firmware
MU02 is the last version, so there are no newer possibly fixed versions
and if the MU02 version has broken LPM then the MU01 almost certainly
also has broken LPM, so this commit changes the quirk to apply to all
firmware versions.
Fixes: b17e5729a630 ("libata: disable LPM for Crucial BX100 SSD 500GB...")
Cc: stable@vger.kernel.org
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
There have been reports of the Crucial M500 480GB model not working
with LPM set to min_power / med_power_with_dipm level.
It has not been tested with medium_power, but that typically has no
measurable power-savings.
Note the reporters Crucial_CT480M500SSD3 has a firmware version of MU03
and there is a MU05 update available, but that update does not mention any
LPM fixes in its changelog, so the quirk matches all firmware versions.
In my experience the LPM problems with (older) Crucial SSDs seem to be
limited to higher capacity versions of the SSDs (different firmware?),
so this commit adds a NOLPM quirk for the 480 and 960GB versions of the
M500, to avoid LPM causing issues with these SSDs.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Martin Steigerwald <martin@lichtvoll.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If the server is malicious then *bytes_read could be larger than the
size of the "target" buffer. It would lead to memory corruption when we
do the memcpy().
Reported-by: Dr Silvio Cesare of InfoSect <Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.16 cycle.
A slightly fiddly revert then fix pair in here as the bug lead to
an unused local variable that was then removed without us noticing
the bug. The revert should only be needed on 4.16 - the fix
goes back futher.
* ccs811
- Fix the transition from 'boot' to 'application' mode. Fixes the case
where the power is not cut between boot cycles.
* meson-saradc
- Fix missing mutex_unlock in an error path.
* sd-modulator
- Fix bindings doc to have the right value of io-channel-cells to reflect
that this device type only ever outputs one channel.
* st-accel
- Revert drop of redundant pointer patch.
- Use the now available pointer to avoid overwriting the platform data
pointer and causing trouble on reprobing the driver.
* st-pressure
- Use local copy of the platform data pointer to avoid overwriting the
one associated with the device, which would cause issues on reprobing
the driver.
* stm32-dfsdm
- Use the right regmap_cfg for the type of device.
- Correct the ID passed to stop channel to be the channel one.
- Correct which clock is used to allow for the 'audio' clock.
- Fix allocation of channels when more than one is enabled.
|
|
This fixes use after free introduced by the last cc770 patch.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Fixes: 746201235b3f ("can: cc770: Fix queue stall & dropped RTR reply")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Section was not properly computed. The value of OOB region definition is
always ECC section 0 information in the OOB area, but we want to get all
the ECC bytes information, so we should call
mtd_ooblayout_ecc(mtd, section++, &oobregion) until it returns -ERANGE.
Fixes: c2b78452a9db ("mtd: use mtd_ooblayout_xxx() helpers where appropriate")
Cc: <stable@vger.kernel.org>
Signed-off-by: OuYang ZhiZhong <ouyzz@yealink.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Revert commit c68f0676ef7d ("ACPI / battery: Add quirk for Asus
GL502VSK and UX305LA") and commit 4446823e2573 ("ACPI / battery: Add
quirk for Asus UX360UA and UX410UAK").
On many many Asus products, the battery is sometimes reported as
charging or discharging even when it is full and you are on AC power.
This change quirked the kernel to avoid advertising the discharging
state when this happens on 4 laptop models, under the belief that
this was incorrect information. I presume it originates from user
reports who are confused that their battery status icon says that it
is discharging.
However, the reported information is indeed correct, and the quirk
approach taken is inadequate and more thought is needed first.
Specifically:
1. It only quirks discharging state, not charging
2. There are so many different Asus products and DMI naming variants
within those product families that behave this way; Linux could
grow to quirk hundreds of products and still not even be close at
"winning" this battle.
3. Asus previously clarified that this behaviour is intentional. The
platform will periodically do a partial discharge/charge cycle
when the battery is full, because this is one way to extend the
lifetime of the battery (leaving a battery at 100% charge and
unused will decrease its usable capacity over time).
My understanding is that any decent consumer product will have
this behaviour, but it appears that Asus is different in that
they expose this info through ACPI.
However, the behaviour seems correct. The ACPI spec does not
suggest in that the platform should hide the truth. It lets you
report that the battery is full of charge, and discharging, and
with external power connected; and Asus does this.
4. In terms of not confusing the user, this seems like something that
could/should be handled by userspace, which can also detect these
same (accurate) conditions in the general case.
Revert this quirk before it gets included in a release, while we look
for better approaches.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since commit 846c7dfc1193 ("drm/atomic: Try to preserve the crtc enabled
state in drm_atomic_remove_fb, v2."), removing the last framebuffer will
no longer disable the corresponding pipeline, which causes the KMS core
to complain about leaked connectors on driver unbind.
Fix this by calling drm_atomic_helper_shutdown() on driver unbind, which
will cause all display pipelines to be shut down and therefore drop the
extra references on the connectors.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The regulator is controlled as part of runtime PM, so it should not be
additionally disabled from the ->exit() callback.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Detaching from an IOMMU group multiple times can lead to a crash. This
could potentially be fixed in the IOMMU driver, but it's easy to avoid
the subsequent detach operations in this driver, so do that as well.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When driver register its component to ALSA SoC, almost all drivers are
using snd_soc_register_component(), but soc-generic-dmaengine-pcm is
using snd_soc_add_component().
Existing component function had been assumed that registered component
was allocated, and it calling kfree() for it.
But, the user who used snd_soc_add_component() doesn't.
This patch uses devm_kzalloc() instead of kzalloc() for component,
and doesn't call kree() anymore.
This patch fixes commit be7ee5f32a9a ("ASoC: soc-generic-dmaengine-pcm:
replace platform to component").
Allwinner H3 SoC will crash without this patch.
Thanks Jernej report.
Reported-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
glibc keeps getting cleverer, and my version now turns raise() into
more than one syscall. Since the test relies on ptrace seeing an
exact set of syscalls, this breaks the test. Replace raise(SIGSTOP)
with syscall(SYS_tgkill, ...) to force glibc to get out of our way.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/bc80338b453afa187bc5f895bd8e2c8d6e264da2.1521300271.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Validate the topology input before we dereference the pointer.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Improve the DPCM BE search debug output to make it easier to debug
issues in topologies.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now when a helper for unreferencing device nodes is available
we can get rid of the local implementation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
hw_params()
The I2S controller can handle sample rates only up to 96000 and the CPU DAI
has already related constraint set so drop the impossible 176400, 192000
switch cases.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case of sample rates lower than 44100 currently there is too low MCLK
frequency set for the CODEC. Playback fails with following errors:
$ speaker-test -c2 -t sine -f 1500 -l2 -r 32000
Sine wave rate is 1500.0000Hz
Rate set to 32000Hz (requested 32000Hz)
Buffer size range from 128 to 131072
Period size range from 64 to 65536
Using max buffer size 131072
Periods = 4
Unable to set hw params for playback: Invalid argument
Setting of hwparams failed: Invalid argument
[ 497.883700] max98090 1-0010: Invalid master clock frequency
To fix this the I2S root clock's frequency is increased, depending
on sampling rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Component driver for the tda7419 audio processor.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DeviceTree binding for the tda7419 audio processor.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a device-tree binding for Texas Instrument's PCM1789 codec.
For the moment, only I2C bus is supported but SPI could be added
in future.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add Texas Instruments's PCM1789 DAC support.
It is a simple DAC and does not have many registers.
One particularity about this DAC is that the clocks must be
always enabled. Also, an entire software reset is necessary
while starting to play a sound otherwise, the clocks are not
synchronized (so the DAC is not able to send data).
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document support for the sound modules in the Renesas M3-W (r8a7796)
SoC.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: d06f33aed85c ("ASoC: da7210: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Compatible for XU4 audio is not being used. Instead the board uses the
same compatible as XU3. The devices are now just compatible so they
should use the same value. Mark "hardkernel,odroid-xu4-audio" as being
deprecated so in this future could be removed to limit useless
properties.
Additionally add older compatibles appearing in the bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: 10dc44c6462d ("ASoC: wm8400: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's not necessary to unregister a component registered
with devm_snd_soc_register_component().
Fixes: f1b5bf07365d ("ASoC: mt2701/mt8173: replace platform to componen")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds syscon property for specifying soc-glue core.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state. After
resetting of SoC Hi-Z state is selected. This driver set to signal
output state when syscon property is available.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds syscon property for specifying soc-glue core into
DT binding documentation.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state. If you don't
need to use features on soc-glue described above you can ommit this
property.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
