| Age | Commit message (Collapse) | Author |
|---|
|
The ISR currently consumes the rx buffer data and re-enables transmission
from within interrupt context. This is bad because if the interrupt
occurs again before the ISR exits, the new interrupt will be erroneously
cleared by the still completing ISR.
Simplified the ISR by just setting the completion variable and exiting with
no action. Then just looped the transmit functionality in
xilinx_spi_txrx_bufs().
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The code uses
return foo;
goto err_type;
when instead the form should have been
ret = foo;
goto err_type;
Here this causes a useful iio_device_put to be skipped.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
If we pass an invalid clock type then "ts" is never set. We need to
check for errors earlier, otherwise we end up passing uninitialized
stack data to userspace.
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The register access to enable hardware flow control depends on the
device port number and not the port minor number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the no longer used endpoint-array access completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
And make the lines easier to read.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In summary, the symptom is intermittent key events lost after resume
on some machines with synaptics touchpad (seems this is synaptics _only_),
and key events loss is due to serio port reconnect after psmouse sync lost.
Removing psmouse and inserting it back during the suspend/resume process
is able to work around the issue, so the difference between psmouse_connect()
and psmouse_reconnect() is the key to the root cause of this problem.
After comparing the two different paths, synaptics driver has its own
implementation of synaptics_reconnect(), and the missing psmouse_probe()
seems significant, the patch below added psmouse_probe() to the reconnect
process, and has been verified many times that the issue could not be reliably
reproduced.
There are two PS/2 commands in psmouse_probe():
1. PSMOUSE_CMD_GETID
2. PSMOUSE_CMD_RESET_DIS
Only the PSMOUSE_CMD_GETID seems to be significant. The
PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying
several times. So we have only implemented this patch to issue
the PSMOUSE_CMD_GETID so far.
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Signed-off-by: James M Leddy <james.leddy@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In intel_sdvo_get_lvds_modes() the wrong i2c adapter record is used
for DDC. Thus the code will always have to rely on a LVDS panel
mode supplied by VBT.
In most cases this succeeds, so this didn't get detected for quite
a while.
This regression seems to have been introduced in
commit f899fc64cda8569d0529452aafc0da31c042df2e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jul 20 15:44:45 2010 -0700
drm/i915: use GMBUS to manage i2c links
Signed-off-by: Egbert Eich <eich@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about which commit likely introduced this issue.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
... instead of applying to all interfaces.
Reference: http://forums.gentoo.org/viewtopic-p-6886404.html
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The xen_play_dead is an undead function. When the vCPU is told to
offline it ends up calling xen_play_dead wherin it calls the
VCPUOP_down hypercall which offlines the vCPU. However, when the
vCPU is onlined back, it resumes execution right after
VCPUOP_down hypercall.
That was OK (albeit the API for play_dead assumes that the CPU
stays dead and never returns) but with commit 4b0c0f294
(tick: Cleanup NOHZ per cpu data on cpu down) that is no longer safe
as said commit resets the ts->inidle which at the start of the
cpu_idle loop was set.
The net effect is that we get this warn:
Broke affinity for irq 16
installing Xen timer for CPU 1
cpu 1 spinlock event irq 48
------------[ cut here ]------------
WARNING: at /home/konrad/linux-linus/kernel/time/tick-sched.c:935 tick_nohz_idle_exit+0x195/0x1b0()
Modules linked in: dm_multipath dm_mod xen_evtchn iscsi_boot_sysfs
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.10.0-rc3upstream-00068-gdcdbe33 #1
Hardware name: BIOSTAR Group N61PB-M2S/N61PB-M2S, BIOS 6.00 PG 09/03/2009
ffffffff8193b448 ffff880039da5e60 ffffffff816707c8 ffff880039da5ea0
ffffffff8108ce8b ffff880039da4010 ffff88003fa8e500 ffff880039da4010
0000000000000001 ffff880039da4000 ffff880039da4010 ffff880039da5eb0
Call Trace:
[<ffffffff816707c8>] dump_stack+0x19/0x1b
[<ffffffff8108ce8b>] warn_slowpath_common+0x6b/0xa0
[<ffffffff8108ced5>] warn_slowpath_null+0x15/0x20
[<ffffffff810e4745>] tick_nohz_idle_exit+0x195/0x1b0
[<ffffffff810da755>] cpu_startup_entry+0x205/0x250
[<ffffffff81661070>] cpu_bringup_and_idle+0x13/0x15
---[ end trace 915c8c486004dda1 ]---
b/c ts_inidle is set to zero. Thomas suggested that we just add a workaround
to call tick_nohz_idle_enter before returning from xen_play_dead() - and
that is what this patch does and fixes the issue.
We also add the stable part b/c git commit 4b0c0f294 is on the stable
tree.
CC: stable@vger.kernel.org
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Panel fitters on ivb/hsw are not created equal since not all of them
support the new high-quality upscaling mode. To offset this the hw
allows us to freely assign the pfits to pipes.
Since our code currently doesn't support this we might fall over when
taking over firmware state. So check for this case and WARN about it.
We can then improve the code once we've hit this in the wild. Or once
we decide to support the improved upscale modes, though that requires
global arbitrage of modeset resources across crtcs.
v2: Check for IS_GEN7 instead of IS_IVB || IS_HSW as suggested by
Paulo in his review comment.
Suggested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We can get at this easily through intel_crtc->config now.
v2: Drop more stuff gcc spotted.
v3: Drop even more stuff gcc spotted.
v4: Yet more ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This prepares a bit for the next big patch, where we switch the
semantics of the different clocks in the pipe config around.
Since I've broken cpu eDP PLL handling in the first version I've
figured some refactoring is in order.
Split out on request from Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We currently mutliply the link_bw of the fdi link with the pixel
multiplier, which is wrong: The FDI link doesn't suddenly grow more
bandwidth. In reality the pixel mutliplication only happens in the PCH,
before the pixels are fed into the port.
But since we our code treats the uses the target clock after pixels
are doubled (tripled, ...) already, we need to correct this.
Semantically it's clearer to divide the target clock to get the fdi
dotclock instead of multiplying the bw, so do that instead.
Note that the target clock is already multiplied by the same factor,
so the division will never loose accuracy for the M/N computation.
The lane computation otoh used the wrong value, we also need to feed
the fdi dotclock to that.
Split out on a request from Paulo Zanoni.
v2: Also fix the lane computation, it used the target clock to compute
the bw requirements, not the fdi dotclock (i.e. adjusted with the
pixel multiplier). Since sdvo only uses the pixel multiplier for
low-res modes (with a dotclock below 100MHz) we wouldn't ever have
rejected a bogus mode, but just used an inefficient fdi config.
v3: Amend the commit message to explain better what the change for the
fdi lane config computation is all about. Requested by Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Since I stand by my rule that splitting functions should only do an
exact copy, this is a follow-up patch.
Suggested-by: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now that the DP madness is cleared out, this is all only per-platform.
So move it out from the intel clock limits structure.
While at it drop the intel prefix on the static functions, call the
vtable entry find_dpll (since it's for the display pll) and rip out
the now unnecessary forward declarations.
Note that the parameters of ->find_dpll are still unchanged, but they
eventually need to be moved over to just take in a pipe configuration.
But currently a lot of things are still missing from the pipe
configuration (reflock, output-specific dpll limits and preferences,
downclocked dotclock). So this will happen in a later step.
Note that intel_g4x_limit has a peculiar case where it selects
intel_limits_i9xx_sdvo as the limit. This is pretty bogus and also not
used since the only output types left are DP and native TV-out which
both use special pre-tuned dpll values.
v2: Re-add comment for the find_pll callback (requested by Paulo) and
elaborate on why the transformation is correct for g4x platforms (to
clarify a review question from Paulo). Double up on that by adding a
WARN as suggested by Paulo Zanoni on irc.
v3: Initialize limits to NULL since gcc is now unhappy.
v4: v2/3 will blow up with a NULL dereference in ->find_dpll for dp and
TV-out ports, spotted by Paulo on irc. So just give up on this madness for
now, and leave this to be fixed in a later patch.
v5: Since the ever-so-slight change for g4x might result in some dpll
parameter computation failing spuriously where before it didn't for
ports with preset dpll settings (DP & TV-out) override this. For
paranoia also do it in the ilk+ code.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pineview is just different.
Also split out i9xx_clock from intel_clock and drop the now redundant
struct device * parameter.
Note that in this patch I kill an XXX comment about 100MHz clocks. I
couldn't figure out what this is about, and we don't seem to have any
bug reports about this either. I suspect that it's a remnant from when
the i9xx and ilk+ modeset code was all in the same file since ilk+
does indeed have a 100MHz clock. So I've just killed it to stop the
cargo-culting.
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Since this is run in the compute config stage we need to check
the new_ pointers, i.e the stage output routing, not the current
modeset layout. Also there was a little logic bug in properly skipping
connectors: The old code did not skip any unused connectors and so
clamped to whatever was left in there (usually 0 if that connector
hasn't seen a EDID 1.4 screen ever since boot-up).
This has been broken when moving the pipe bpp selection in
commit 4e53c2e010e531b4a014692199e978482d471c7e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:44:58 2013 +0100
drm/i915: precompute pipe bpp before touching the hw
To avoid too much casting switch from drm_ to intel_ types.
Also add a bit of debug output to help reconstructing what's going
on.
v2: Try to clarify this a bit:
- s/pipe_config_set_bpp/compute_baseline_pipe_bpp/ to make it clearer
at which stage this function is run. Also add a comment about what
it does.
- Extract the sink clamping into it's own function.
v3: Actually make it compile.
v4: Split out all the prep refactoring to make the bugfix stick out
really badly. Also elaborate a bit in the commit message about the
nature of the bugfix.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
As a prep work to fix it up:
- Use intel_connector instead of drm_connector to avoid too much
upcasting in the bugfix patch.
- Extract the connector bpp clamping from the loop-over-connectors
logic.
- Bikeshed function names (to make it clearer that
acompute_baseline_pipe_bpp runs in the compute stage of the modeset
sequence) and add a comment to make it clearer what it does.
No functional change in this patch.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Update the CMT clockevent rating from 125 to 80.
This resolves a boot-failure regression for kzm9g-reference in v3.10-rc1
introduced by f7db706b132f11c79ae1d74b2382e0926cf31644 ("ARM: 7674/1: smp:
Avoid dummy clockevent being preferred over real").
The patch noted above reduces the rating of dummy clockevent from 400 to 100.
This patch reduces the rating of CMT so that it is once again less than that
of the dummy clockevent.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The USB_OVCn pins are alternate options for USB over-current detection
when using a 3.3V USB interface. As they're not mandatory they can be
used independently of the USB PENC pins. Don't group the USB_OVCn and
PENC pins to avoid conflicts when the USB_OVCn pins are used by another
function.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small fixes for v3.10, documentation things in the core and a
few driver bugs."
* tag 'regulator-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: palmas: Fix "enable_reg" to point to the correct reg for SMPS10
regulator: palmas: Fix incorrect condition
regulator: core: Correct spelling mistake in comment
regulator: dbx500: Make local symbol static
regulator: Fix kernel-doc generation warnings.
|
|
Pull jfs bugfixes from David Kleikamp:
"A couple jfs bug fixes for 3.10-rc5"
* tag 'jfs-3.10-rc5' of git://github.com/kleikamp/linux-shaggy:
fs/jfs: Add check if journaling to disk has been disabled in lbmRead()
jfs: Several bugs in jfs_freeze() and jfs_unfreeze()
|
|
Smatch complains that if we pass an invalid clock type then "ts" is
never set. We need to check for errors earlier, otherwise we end up
passing uninitialized stack data to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In certain cases, dma_alloc_coherent returns NULL. Add check for
NULL pointer.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Many debug messages missed end-of-line.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Callback .start_streaming is called once for every queue,
so v4l2_ctrl_handler_setup was called twice during stream start.
Moving v4l2_ctrl_handler_setup to context initialization
reduces numbers of calls and seems to be more consistent with API.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes a bug which caused overwriting h264 codec
parameters by mpeg4 parameters during V4L2 control setting.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
MFC uses two clocks - MFC gate clock and special clock
which is named as "sclk_mfc" in exynos4 and "aclk_333" in
exynos5 SoC. The driver was doing just a clk_prepare on
this special clock without a clk_enable call. As this
sclk is the parent of gate clock, it gets prepared and
enabled along with the gate clock. So there is no need
for the driver to use this sclk. This patch removes the
sclk usage from driver.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes following compilation warning:
CC [M] drivers/media/platform/s5p-mfc/s5p_mfc_opr_v6.o
drivers/media/platform/s5p-mfc/s5p_mfc_opr_v6.c:1733:12: warning: ‘s5p_mfc_get_decoded_status_v6’ defined but not used
It assigns existing but not used s5p_mfc_get_dec_status_v6() function to the
get_dec_status callback. It seems the get_dec_status callback is not used
anyway, as there is no corresponding s5p_mfc_hw_call().
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Save flags correctly when taking spinlocks in v4l2_m2m_try_schedule.
Signed-off-by: John Sheu <sheu@google.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The v4l2_m2m_poll() does not need to wait if there is already a buffer in
done_list of source and destination queues, but current v4l2_m2m_poll() always
waits. So done_list of each queue is checked before calling poll_wait().
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The vb2_poll() does not need to wait next vb_buffer_done() if there is already
a buffer in done_list of queue, but current vb2_poll() always waits.
So done_list is checked before calling poll_wait().
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
MFC v6 needs minimum number of output buffers to be queued
for encoder depending on the stream type and profile.
The patch modifies the driver so that encoding cannot be
started with lesser number of OUTPUT buffers than required.
This also fixes the crash happeninig during multi instance
encoder-decoder simultaneous run due to memory allocation
happening from interrupt context.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit cfcec52e9781f08948c6eb98198d65c45be75a70.
This regresses a longstanding behaviour on X86 systems, which end up with
PCI serial ports moving between ttyS4 and ttyS0 when you bisect to opposite
sides of this commit, resulting in the need to constantly modify the console
setting in order to bisect across it.
Please revert, we can work on solving this for ARM platforms in a less
disruptive way.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Karthik Manamcheri <karthik.manamcheri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure that the uart controller clock is enabled prior to writing to the
interrupt mask and pending registers in the s3c24xx_serial_init_port
function.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We only want to enable hardware flow control if RTS/CTS pins
are connected.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
|
|
This patch makes GFS2 immediately reclaim/delete all iopen glocks
as soon as they're dequeued. This allows deleters to get an
EXclusive lock on iopen so files are deleted properly instead of
being set as unlinked.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
This version has one more correction: the vmalloc calls are replaced
by __vmalloc calls to preserve the GFP_NOFS flag.
When GFS2's directory management code allocates buffers for a
directory hash table, if it can't get the memory it needs, it
currently gives a bad return code. Rather than giving an error,
this patch allows it to use virtual memory rather than kernel
memory for the hash table. This should make it possible for
directories to function properly, even when kernel memory becomes
very fragmented.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
This patch calls get_write_access in a few functions. This
merely increases inode->i_writecount for the duration of the function.
That will ensure that any file closes won't delete the inode's
multi-block reservation while the function is running.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
