| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds SCTP_PR_ASSOC_STATUS to sctp sockopt, which is used
to dump the prsctp statistics info from the asoc. The prsctp statistics
includes abandoned_sent/unsent from the asoc. abandoned_sent is the
count of the packets we drop packets from retransmit/transmited queue,
and abandoned_unsent is the count of the packets we drop from out_queue
according to the policy.
Note: another option for prsctp statistics dump described in rfc is
SCTP_PR_STREAM_STATUS, which is used to dump the prsctp statistics
info from each stream. But by now, linux doesn't yet have per stream
statistics info, it needs rfc6525 to be implemented. As the prsctp
statistics for each stream has to be based on per stream statistics,
we will delay it until rfc6525 is done in linux.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds SCTP_DEFAULT_PRINFO to sctp sockopt. It is used
to set/get sctp Partially Reliable Policies' default params,
which includes 3 policies (ttl, rtx, prio) and their values.
Still, if we set policy params in sndinfo, we will use the params
of sndinfo against chunks, instead of the default params.
In this patch, we will use 5-8bit of sp/asoc->default_flags
to store prsctp policies, and reuse asoc->default_timetolive
to store their values. It means if we enable and set prsctp
policy, prior ttl timeout in sctp will not work any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to section 4.5 of rfc7496, prsctp_enable should be per asoc.
We will add prsctp_enable to both asoc and ep, and replace the places
where it used net.sctp->prsctp_enable with asoc->prsctp_enable.
ep->prsctp_enable will be initialized with net.sctp->prsctp_enable, and
asoc->prsctp_enable will be initialized with ep->prsctp_enable. We can
also modify it's value through sockopt SCTP_PR_SUPPORTED.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LPM can be enabled via a DDC write command at specific DDC ID.
As any other DDC value, this is up to the DDC config file to
include (or not) the low power mode configuration.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This reverts commit 4386f5662e63 ("net: ethernet: bcmgenet: use
phy_ethtool_{get|set}_link_ksettings")
This patch is wrong, the function phy_ethtool_{get|set}_link_ksettings
don't check if the device is running, but the driver bcmgenet need this
check.
The function {get|set}_settings need to access the mdio bus, and this
bus may only be used when the device is running. Otherwise, the clock
is disable and a mdio access will fail.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
net: dsa: b53: Add Broadcom NSP switch support
This patch series updates the B53 driver to support Broadcom's Northstar Plus
Soc integrated switch.
Unlike the version of the core present in BCM5301x/Northstar, we cannot read the
full chip id of the switch, so we need to get the information about our switch
id from Device Tree.
Other than that, this is a regular Broadcom Ethernet switch which is register
compatible for all practical purposes with the existing switch driver.
Since DSA requires a working CPU Ethernet MAC driver this depends on Jon
Mason's AMAC/BGMAC driver changes to support NSP. Board specific changes depend
on patches present in Broadcom's ARM SoC branches and will be posted in a short
while.
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For Northstart Plus SoCs, we cannot detect the switch because only the
revision information is provied in the Management page, instead, rely on
Device Tree to tell us the chip id, and pass it down using the
b53_platform_data structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If socket filter truncates an udp packet below the length of UDP header
in udpv6_queue_rcv_skb() or udp_queue_rcv_skb(), it will trigger a
BUG_ON in skb_pull_rcsum(). This BUG_ON (and therefore a system crash if
kernel is configured that way) can be easily enforced by an unprivileged
user which was reported as CVE-2016-6162. For a reproducer, see
http://seclists.org/oss-sec/2016/q3/8
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
Here are a couple batman-adv bugfix patches, all by Sven Eckelmann:
- Fix possible NULL pointer dereference for vlan_insert_tag (two patches)
- Fix reference handling in some features, which may lead to reference
leaks or invalid memory access (four patches)
- Fix speedy join: DHCP packets handled by the gateway feature should
be sent with 4-address unicast instead of 3-address unicast to make
speedy join work. This fixes/speeds up DHCP assignment for clients
which join a mesh for the first time. (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
register_vga_switcheroo() sets the PM ops from the hda structure which
is freed later in azx_free. Make sure that these ops are cleared.
Caught by KASAN, initially noticed due to a general protection fault.
Fixes: 246efa4a072f ("snd/hda: add runtime suspend/resume on optimus support (v4)")
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently the two are unioned together, but I don't think that's safe.
It looks like get_cached_acl could race with the last put in
posix_acl_release. get_cached_acl calls atomic_inc_not_zero on
a_refcount, but that field could have already been clobbered by
call_rcu, and may no longer be zero. Fix this by de-unioning the two
fields.
Fixes: b8a7a3a66747 (posix_acl: Inode acl caching fixes)
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Variable "now" seems to be genuinely used unintialized
if branch
if (CPUCLOCK_PERTHREAD(timer->it_clock)) {
is not taken and branch
if (unlikely(sighand == NULL)) {
is taken. In this case the process has been reaped and the timer is marked as
disarmed anyway. So none of the postprocessing of the sample is
required. Return right away.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160707223911.GA26483@p183.telecom.by
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If/Else/While execution to per-table basis"
Revert commit 3d4b7ae96d81 (ACPI 2.0 / AML: Improve module level
execution by moving the If/Else/While execution to per-table basis)
that enabled the execution of module-level AML after loading each
table (rather than after all AML tables have been loaded), but
overlooked locking issues resulting from that change.
Fixes: 3d4b7ae96d81 (ACPI 2.0 / AML: Improve module level execution by moving the If/Else/While execution to per-table basis)
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
table loading"
Revert commit 2f38b1b16d92 (ACPICA: Namespace: Fix deadlock triggered by
MLC support in dynamic table loading) that attempted to fix a deadlock
issue introduced by a previous commit, but it led to a lock ordering
inconsistency that caused further problems to appear.
Fixes: 2f38b1b16d92 (ACPICA: Namespace: Fix deadlock triggered by MLC support in dynamic table loading)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Revert commit 45209046c47b (ACPICA: Namespace: Fix namespace/interpreter
lock ordering) that renders Dell Precision 5510 with the latest (1.2.10)
BIOS applied unable to boot.
Fixes: 45209046c47b (ACPICA: Namespace: Fix namespace/interpreter lock ordering)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121701
Reported-by: Greg White <gwhite@kupulau.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The driver is now ready to load the new firmware versions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This patch corrects an off-by-one error in the DecodeQ931 function in
the nf_conntrack_h323 module. This error could result in reading off
the end of a Q.931 frame.
Signed-off-by: Toby DiPasquale <toby@cbcg.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-next
Simon Horman says:
====================
IPVS Updates for v4.8
please consider these enhancements to the IPVS. This alters the behaviour
of the "least connection" schedulers such that pre-established connections
are included in the active connection count. This avoids overloading
servers when a large number of new connections arrive in a short space of
time - e.g. when clients reconnect after a node or network failure.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We can pass the netns pointer as parameter to the functions that need to
gain access to it. From basechains, I didn't find any client for this
field anymore so let's remove this too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If we want to use ct packets expr, and add a rule like follows:
# nft add rule filter input ct packets gt 1 counter
We will find that no packets will hit it, because
nf_conntrack_acct is disabled by default. So It will
not work until we enable it manually via
"echo 1 > /proc/sys/net/netfilter/nf_conntrack_acct".
This is not friendly, so like xt_connbytes do, if the user
want to use ct byte/packet expr, enable nf_conntrack_acct
automatically.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
physdev_mt() will check skb->nf_bridge first, which was alloced in
br_nf_pre_routing. So if we want to use --physdev-out and physdev-is-out,
we need to match it in FORWARD or POSTROUTING chain. physdev_mt_check()
only checked physdev-out and missed physdev-is-out. Fix it and update the
debug message to make it clearer.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Marcelo R Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
It did use a fixed-size bucket list plus single lock to protect add/del.
Unlike the main conntrack table we only need to add and remove keys.
Convert it to rhashtable to get table autosizing and per-bucket locking.
The maximum number of entries is -- as before -- tied to the number of
conntracks so we do not need another upperlimit.
The change does not handle rhashtable_remove_fast error, only possible
"error" is -ENOENT, and that is something that can happen legitimetely,
e.g. because nat module was inserted at a later time and no src manip
took place yet.
Tested with http-client-benchmark + httpterm with DNAT and SNAT rules
in place.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs
Simon Horman says:
====================
Second Round of IPVS Fixes for v4.7
The fix from Quentin Armitage allows the backup sync daemon to
be bound to a link-local mcast IPv6 address as is already the case
for IPv4.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The nat extension structure is 32bytes in size on x86_64:
struct nf_conn_nat {
struct hlist_node bysource; /* 0 16 */
struct nf_conn * ct; /* 16 8 */
union nf_conntrack_nat_help help; /* 24 4 */
int masq_index; /* 28 4 */
/* size: 32, cachelines: 1, members: 4 */
/* last cacheline: 32 bytes */
};
The hlist is needed to quickly check for possible tuple collisions
when installing a new nat binding. Storing this in the extension
area has two drawbacks:
1. We need ct backpointer to get the conntrack struct from the extension.
2. When reallocation of extension area occurs we need to fixup the bysource
hash head via hlist_replace_rcu.
We can avoid both by placing the hlist_head in nf_conn and place nf_conn in
the bysource hash rather than the extenstion.
We can also remove the ->move support; no other extension needs it.
Moving the entire nat extension into nf_conn would be possible as well but
then we have to add yet another callback for deletion from the bysource
hash table rather than just using nat extension ->destroy hook for this.
nf_conn size doesn't increase due to aligment, followup patch replaces
hlist_node with single pointer.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We don't need to acquire the bucket lock during early drop, we can
use lockless traveral just like ____nf_conntrack_find.
The timer deletion serves as synchronization point, if another cpu
attempts to evict same entry, only one will succeed with timer deletion.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
From: Liping Zhang <liping.zhang@spreadtrum.com>
Similar to ctnl_untimeout, when hash resize happened, we should try
to do unhelp from the 0# bucket again.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Imagine such situation, nf_conntrack_htable_size now is 4096, we are doing
ctnl_untimeout, and iterate on 3000# bucket.
Meanwhile, another user try to reduce hash size to 2048, then all nf_conn
are removed to the new hashtable. When this hash resize operation finished,
we still try to itreate ct begin from 3000# bucket, find nothing to do and
just return.
We may miss unlinking some timeout objects. And later we will end up with
invalid references to timeout object that are already gone.
So when we find that hash resize happened, try to unlink timeout objects
from the 0# bucket again.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When we do "cat /proc/net/nf_conntrack", and meanwhile resize the conntrack
hash table via /sys/module/nf_conntrack/parameters/hashsize, race will
happen, because reader can observe a newly allocated hash but the old size
(or vice versa). So oops will happen like follows：
BUG: unable to handle kernel NULL pointer dereference at 0000000000000017
IP: [<ffffffffa0418e21>] seq_print_acct+0x11/0x50 [nf_conntrack]
Call Trace:
[<ffffffffa0412f4e>] ? ct_seq_show+0x14e/0x340 [nf_conntrack]
[<ffffffff81261a1c>] seq_read+0x2cc/0x390
[<ffffffff812a8d62>] proc_reg_read+0x42/0x70
[<ffffffff8123bee7>] __vfs_read+0x37/0x130
[<ffffffff81347980>] ? security_file_permission+0xa0/0xc0
[<ffffffff8123cf75>] vfs_read+0x95/0x140
[<ffffffff8123e475>] SyS_read+0x55/0xc0
[<ffffffff817c2572>] entry_SYSCALL_64_fastpath+0x1a/0xa4
It is very easy to reproduce this kernel crash.
1. open one shell and input the following cmds:
while : ; do
echo $RANDOM > /sys/module/nf_conntrack/parameters/hashsize
done
2. open more shells and input the following cmds:
while : ; do
cat /proc/net/nf_conntrack
done
3. just wait a monent, oops will happen soon.
The solution in this patch is based on Florian's Commit 5e3c61f98175
("netfilter: conntrack: fix lookup race during hash resize"). And
add a wrapper function nf_conntrack_get_ht to get hash and hsize
suggested by Florian Westphal.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This adds support for TSE PCS that uses SGMII adapter when the phy-mode of
the dwmac is set to sgmii.
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The well-spotted fallocate undo fix is good in most cases, but not when
fallocate failed on the very first page. index 0 then passes lend -1
to shmem_undo_range(), and that has two bad effects: (a) that it will
undo every fallocation throughout the file, unrestricted by the current
range; but more importantly (b) it can cause the undo to hang, because
lend -1 is treated as truncation, which makes it keep on retrying until
every page has gone, but those already fully instantiated will never go
away. Big thank you to xfstests generic/269 which demonstrates this.
Fixes: b9b4bb26af01 ("tmpfs: don't undo fallocate past its last page")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the target needs more time to process the received PDU, it sends
Response Timeout Extension (RTOX) PDU.
When the initiator receives a RTOX PDU, it must reply with a RTOX PDU
and extends the current rwt value with the formula:
rwt_int = rwt * rtox
This patch takes care of the rtox value passed by the target in the RTOX
PDU and extends the timeout for the next response accordingly.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When sending an ATR_REQ, the initiator must wait for the ATR_RES at
least 'RWT(nfcdep,activation) + dRWT(nfcdep)' and no more than
'RWT(nfcdep,activation) + dRWT(nfcdep) + dT(nfcdep,initiator)'. This
gives a timeout value between 1237 ms and 1337 ms. This patch defines
DIGITAL_ATR_RES_RWT to 1337 used for the timeout value of ATR_REQ
command.
For other DEP PDUs, the initiator must wait between 'RWT + dRWT(nfcdep)'
and 'RWT + dRWT(nfcdep) + dT(nfcdep,initiator)' where RWT is given by
the following formula: '(256 * 16 / f(c)) * 2^wt' where wt is the value
of the TO field in the ATR_RES response and is in the range between 0
and 14. This patch declares a mapping table for wt values and gives RWT
max values between 100 ms and 5049 ms.
This patch also defines DIGITAL_ATR_RES_TO_WT, the maximum wt value in
target mode, to 8.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch frees the RTOX resp sk_buff in initiator mode. It also makes
use of the free_resp exit point for ATN supervisor PDUs in both
initiator and target mode.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With this patch, ACK PDU sk_buffs are now freed and code has been
refactored for better errors handling.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When the target receives a NACK PDU, it re-sends the last sent PDU.
ACK PDUs are received by the target as a reply from the initiator to
chained I-PDUs. There are 3 cases to handle:
- If the target has previously received 1 or more ATN PDUs and the PNI
in the ACK PDU is equal to the target PNI - 1, then it means that the
initiator did not received the last issued PDU from the target. In
this case it re-sends this PDU.
- If the target has received 1 or more ATN PDUs but the ACK PNI is not
the target PNI - 1, then this means that this ACK is the reply of the
previous chained I-PDU sent by the target. The target did not received
it on the first attempt and it is being re-sent by the initiator. The
process continues as usual.
- No ATN PDU received before this ACK PDU. This is the reply of a
chained I-PDU. The target keeps on processing its chained I-PDU.
The code has been refactored to avoid too many indentation levels.
Also, ACK and NACK PDUs were not freed. This is now fixed.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When the initiator sends a DEP_REQ I-PDU, the target device may not
reply in a timely manner. In this case the initiator device must send an
attention PDU (ATN) and if the recipient replies with an ATN PDU in
return, then the last I-PDU must be sent again by the initiator.
This patch fixes how the target handles I-PDU received after an ATN PDU
has been received.
There are 2 possible cases:
- The target has received the initial DEP_REQ and sends back the DEP_RES
but the initiator did not receive it. In this case, after the
initiator has sent an ATN PDU and the target replied it (with an ATN
as well), the initiator sends the saved skb of the initial DEP_REQ
again and the target replies with the saved skb of the initial
DEP_RES.
- Or the target did not even received the initial DEP_REQ. In this case,
after the ATN PDUs exchange, the initiator sends the saved skb and the
target simply passes it up, just as usual.
This behavior is controlled using the atn_count and the PNI field of the
digital device structure.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When allocating chained I-PDUs, there is no need to call skb_reserve()
since it's already done by digital_alloc_skb() and contains enough room
for the driver head and tail data.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch fixes the way an I-PDU is saved in case it needs to be sent
again. It is now copied using pskb_copy() and not simply referenced
using skb_get() since it could be modified by the driver.
digital_in_send_saved_skb() and digital_tg_send_saved_skb() still get a
reference on the saved skb which is re-sent but release it if the send
operation fails. That way the caller doesn't have to take care about skb
ref in case of error.
RTOX supervisor PDU must not be saved as this can override a previously
saved I-PDU that should be re-sent later on.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.
The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.
The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.
When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56
This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.
Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.
Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.
The following should be a comprehensive list of affected models:
iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16]
iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16]
Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12]
Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12]
MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):
irq 17: nobody cared (try booting with the "irqpoll" option)
handlers:
[<ffffffff81374370>] pcie_isr
[<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci]
[<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec]
Disabling IRQ #17
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732
Tested-by: Konstantin Simanov <k.simanov@stlk.ru> # [MacBookPro8,1]
Tested-by: Lukas Wunner <lukas@wunner.de> # [MacBookPro9,1]
Tested-by: Bryan Paradis <bryan.paradis@gmail.com> # [MacBookPro9,2]
Tested-by: Andrew Worsley <amworsley@gmail.com> # [MacBookPro10,1]
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris Milsted <cmilsted@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: b43-dev@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Apply nvidia_bugs quirk only on root bus
Cc: stable@vger.kernel.org # 123456789abc: x86/quirks: Reintroduce scanning of secondary buses
Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de
[ Did minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We used to scan secondary buses until the following commit that
was applied in 2009:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.
We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.
The commit message of 8659c406ade3 notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406ade3 was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.
Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.
If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since the following commit:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
... early quirks are only applied to devices on the root bus.
The motivation was to prevent application of the nvidia_bugs quirk on
secondary buses.
We're about to reintroduce scanning of secondary buses for a quirk to
reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent
regressions, open code the requirement to apply nvidia_bugs only on the
root bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4d5477c1d76b2f0387a780f2142bbcdd9fee869b.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This is to fix some conflicts in iwlwifi.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
drivers/net/wireless/intel/iwlwifi/mvm/scan.c
|
|
This showed up as "6Failed to access..." here.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 1b74dde7c47c ("x86/cpu: Convert printk(KERN_<LEVEL> ...) to pr_<level>(...)")
Link: http://lkml.kernel.org/r/1468170841-17045-1-git-send-email-vegard.nossum@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull MIPS fix from Ralf Baechle:
"Another week with just a single 4.7 fix.
This fixes a possible 'loss' of the huge page bit from pmd on
permission change"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix page table corruption on THP permission changes.
|
|
Mathieu Desnoyers reported that the STACK_FRAME_NON_STANDARD macro
wasn't working with the lttng_filter_interpret_bytecode() function in
the lttng-modules code.
Usually the relocation created by STACK_FRAME_NON_STANDARD creates a
reference to a section symbol like this:
Offset Type Value Addend Name
000000000000000000 X86_64_64 000000000000000000 +3136 .text
But in this case it created a reference to a function symbol:
Offset Type Value Addend Name
000000000000000000 X86_64_64 0x00000000000003a0 +0 lttng_filter_interpret_bytecode
To be honest I have no idea what causes gcc to decide to do one over the
other. But both are valid ELF, so add support for the function symbol.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: lttng-dev@lists.lttng.org
Link: http://lkml.kernel.org/r/9cee42843bc6d94e990a152e4e0319cfdf6756ef.1466023450.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In the prep work I did before enabling BH while handling socket backlog,
I missed two points in DCCP :
1) dccp_v4_ctl_send_reset() uses bh_lock_sock(), assuming BH were
blocked. It is not anymore always true.
2) dccp_v4_route_skb() was using __IP_INC_STATS() instead of
IP_INC_STATS()
A similar fix was done for TCP, in commit 47dcc20a39d0
("ipv4: tcp: ip_send_unicast_reply() is not BH safe")
Fixes: 7309f8821fd6 ("dccp: do not assume DCCP code is non preemptible")
Fixes: 5413d1babe8f ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
