| Age | Commit message (Collapse) | Author |
|---|
|
The WRSTBI bit (disabled by default but enabled by bootloader), when
set, is responsible for resetting voltages to default values of
certain bucks on falling edge of Warm Reset Input pin from AP.
However on some boards (with S2MPS13) the pin is pulled down so any
suspend will effectively trigger the reset of bucks supplying the power
to the little and big cores. In the same time when resuming, these bucks
must provide voltage greater or equal to voltage before suspend to match
the frequency chosen by cpufreq. If voltage (default value of voltage
after reset) is lower than one set by cpufreq before suspend, then
system will hang during resuming.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There are different revisions of the same chipset. For example S2MPS13 has
more than 2 revisions. They differ slightly in regulator constraints.
Print the revision number to easily find which PMIC is used on the board.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In the case of a device tree config the code uses the device ID
from the DT entry to check which codec is required but when storing
the ID into struct arizona it was always using the non-DT SPI device
table to get an ID.
This patch changes the code to store the correct ID into struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Remove the use of #ifdefs around each case statement of the chip ID
and type validation switches.
We must ensure that the contained code still compiles to nothing if
support for that codec was not built into the kernel, to prevent
creation of link references to missing functions. So the ifdefs are
replaced with a use of the IS_ENABLED() macro.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The code was using a switch on the code type to execute
one of several mfd_add_devices() calls. We're already
switching on the code type earlier in the function to
select the correct patch function so we can roll selection
of the mfd device table into the same switch.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If the declared codec type doesn't match the detected type
we issue a log message but carry on registering the device,
so a dev_warn() is appropriate rather than a dev_err()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Currently runtime_suspend will fully power off the codec if
the jack detection is not enabled. Not all future codecs will
have jack detection so to prepare for these codecs this patch
factors out the check so that it be called as needed in the
existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Currently DCVDD isolation is enabled and disabled for
runtime_suspend and runtime_resume. Future codecs will not
have the isolation control so to prepare for these codecs
this patch factors out the isolation control allowing it to
be called as needed in the existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is required since
commit 7e5071199355 ("mfd: tps6105x: Use i2c regmap to access registers").
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We were getting build warning about unused variable 'ret'.
The commit c749db571dcf has removed the use of ret but missed removing
the variable which is unused now.
Fixes: c749db571dcf ("mfd: lm3533: Simplify function return logic")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
rts522a(rts5227s) is derived from rts5227, and mainly same with rts5227.
Add it to file mfd/rts5227.c to support this chip.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Rename get_device_type() to da9062_get_device_type().
This function is only used in this file so make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver depends on ARCH_NOMADIK but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Definitions for GPIO registers 8, 9, 10, 11, 12 and 13 are added into
the register header file.
- DA9052_GPIO_8_9_REG 25
- DA9052_GPIO_10_11_REG 26
- DA9052_GPIO_12_13_REG 27
A modification is also made to the MFD core code to define these registers
as readable and writable. The functions for da9052_reg_readable() and
da9052_reg_writeable() have had their case statements altered to include
these new registers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch documents the DT bindings for the Atmel Flexcom which will be
introduced by sama5d2x SoCs. These bindings will be used by the actual
Flexcom driver to be sent in another patch.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch defines some macros to be used as value for the
"atmel,flexcom-mode" DT property. This value is then written into
the Operating Mode (OPMODE) bit field of the Flexcom Mode Register.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The call to kstrtoul() will corrupt memory on 64 bit systems because an
int is 4 bytes and a long is 8.
Also it's not a good idea to let users trigger a dev_err() because it
just ends up flooding /var/log/messages so I removed the printk.
Fixes: 2ddd2086ea9c ('mfd: add Intel Broxton Whiskey Cove PMIC driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
tps6105 driver provides two cells. One is for GPIO and another one is
for selected mode depending on platform data. When tps6105x is used in
GPIO-only mode, this driver calls mfd_add_devices() with mfd_cell
.name == NULL. This value causes an oops in platform_device_register()
later.
The following patch adds a mfd_cell for each possible mode thereby
excluding .name assignment in runtime.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver handles wakeup irq correctly using irq_set_irq_wake. There's
no need to use IRQF_NO_SUSPEND while registering the interrupt.
This patch removes the use of IRQF_NO_SUSPEND flag.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch solves:
on x86_64:
when CONFIG_ACPI is not enabled:
../drivers/mfd/intel_soc_pmic_bxtwc.c: In function 'bxtwc_probe':
../drivers/mfd/intel_soc_pmic_bxtwc.c:342:2:
error: implicit declaration of function 'acpi_evaluate_integer' [-Werror=implicit-function-declaration]
status = acpi_evaluate_integer(handle, "_HRV", NULL, &hrv);
^
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some EC implementations include a small nvram space used to store
verified boot context data. This boolean property lets us indicate
whether this space is available or not on a specific EC implementation.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The lpc_ich_cells array gives the wrong impression about the
relationship between the watchdog and GPIO devices. They are
completely distinct devices, so this patch separates the
array into distinct mfd_cell structs per device.
A side effect of removing the array, is that the lpc_cells enum
is no longer needed.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add MFD core driver for Intel Broxton Whiskey Cove PMIC,
which is specially accessed by hardware IPC, not a generic
I2C device
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
IRQ control registers of Intel Broxton Whisky Cove PMIC are
separated in two parts, so add secondary IRQ chip.
And the new member of device will be used in PMC IPC regmap APIs.
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
no need to initialise static variable with 0, hence correcting it.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This worked before the dw-hdmi bridge code was changed to validate
the setup data more strictly. Add back support for modes with a
pixel clock up to 216MHz. Even higher clocks should work, but we
are missing the required setup data for now.
Also change the mode validate callbacks to disallow modes with
higher pixelclocks, so we don't end up failing the modeset later
on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The variable can be negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Enable the MEDIA_BUS_FMT_Y8_1X8 format.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This patch allows to use the ARGB4444 color format on planes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This patch adds support for the ARGB4444 color format.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This patch allows to use the RGBX and RGBA 8:8:8:8 formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This patch adds support for the RGBA8888, RGBX8888, BGRA8888, and
BGRX8888 in-memory formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This patch enables the ARGB1555, ABGR1555, RGBA5551,
and BGRA5551 formats to be used on planes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This patch adds support for ARGB1555, ABGR1555, RGBA5551, and BGRA5551
in-memory formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The ipu-v3 core driver is maintained in and merged through
the same trees as the imx-drm drivers that are using it.
This patch adds the drivers/gpu/ipu-v3/ directory to the
i.MX DRM driver section.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Bool initializations should use true and false. Bool tests don't need
comparisons. Based on contributions from Joe Perches, Rusty Russell
and Bruce W Allan.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/boolinit.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Make sure that the task scheduler domain hierarchy is set-up correctly
on systems with single or multi-cluster topology.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Now that we added special handling to the C files in libstub, move
the one remaining arm64 specific EFI stub C file to libstub as
well, so that it gets the same treatment. This should prevent future
changes from resulting in binaries that may execute incorrectly in
UEFI context.
With efi-entry.S the only remaining EFI stub source file under
arch/arm64, we can also simplify the Makefile logic somewhat.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This was introduced by mistake in commit 0f7d9052fb70 ("drm/tegra: Use
new drm_fb_helper functions"). Remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because this value is alreadytaken care by devm_ioremap_resource()
Signed-off-by: Sanjeev Sharma <sanjeev_sharma@mentor.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
