| Age | Commit message (Collapse) | Author |
|---|
|
In order to align with st21nfca, dts configuration properties
ese_present and uicc_present are made available in st-nci driver.
So far, in early development firmware, because
nci_nfcee_mode_set(DISABLE) was not supported we had to try to
enable it during the secure element discovery phase.
After several trials on commercial and qualified firmware it appears
that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are
properly supported.
Such feature also help us to eventually save some time (~5ms) when
only one secure element is connected.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFC_CMD_ACTIVATE_TARGET and NFC_ATTR_SE_PARAMS comments are missing.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Potentially an unexpected HCI event may occur because of a
firmware bug. It could be transparent for the user but we need to
at least log it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add support for proprietary commands useful mainly for
factory testings. Here is a list:
- FACTORY_MODE: Allow to set the driver into a mode where
no secure element are activated. It does not consider any
NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry
like for example RF trimmings or low level drivers
configurations (I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
low level drivers configurations or RF trimmings.
- HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF.
A complete packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
connectivity.
- HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied
on the CLF antenna. A value between 0 and 0x0f is returned. 0 is
maximum.
- HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode.
It is a specific CLF command as there is no GPIO for this.
- HCI_DM_FWUPD_END: Allow to complete firmware update.
- HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied
on the CLF antenna to a reference value.
- MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data
received during a NCI_CORE_INIT_CMD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When rebasing my patchset, I forgot to pick up a cleanup patch to remove
old hotfix in 4.2 release.
Witouth the cleanup, it will screw up new qgroup reserve framework and
always cause minus reserved number.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Between btrfs_allocerved_file_extent() and
btrfs_add_delayed_qgroup_reserve(), there is a window that delayed_refs
are run and delayed ref head maybe freed before
btrfs_add_delayed_qgroup_reserve().
This will cause btrfs_dad_delayed_qgroup_reserve() to return -ENOENT,
and cause transaction to be aborted.
This patch will record qgroup reserve space info into delayed_ref_head
at btrfs_add_delayed_ref(), to eliminate the race window.
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
cleaner_kthread() kthread calls try_to_freeze() at the beginning of every
cleanup attempt. This operation can't ever succeed though, as the kthread
hasn't marked itself as freezable.
Before (hopefully eventually) kthread freezing gets converted to fileystem
freezing, we'd rather mark cleaner_kthread() freezable (as my
understanding is that it can generate filesystem I/O during suspend).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Ancient qgroup code call memcpy() on a extent buffer and use it for leaf
iteration.
As extent buffer contains lock, pointers to pages, it's never sane to do
such copy.
The following bug may be caused by this insane operation:
[92098.841309] general protection fault: 0000 [#1] SMP
[92098.841338] Modules linked in: ...
[92098.841814] CPU: 1 PID: 24655 Comm: kworker/u4:12 Not tainted
4.3.0-rc1 #1
[92098.841868] Workqueue: btrfs-qgroup-rescan btrfs_qgroup_rescan_helper
[btrfs]
[92098.842261] Call Trace:
[92098.842277] [<ffffffffc035a5d8>] ? read_extent_buffer+0xb8/0x110
[btrfs]
[92098.842304] [<ffffffffc0396d00>] ? btrfs_find_all_roots+0x60/0x70
[btrfs]
[92098.842329] [<ffffffffc039af3d>]
btrfs_qgroup_rescan_worker+0x28d/0x5a0 [btrfs]
Where btrfs_qgroup_rescan_worker+0x28d is btrfs_disk_key_to_cpu(),
called in reading key from the copied extent_buffer.
This patch will use btrfs_clone_extent_buffer() to a better copy of
extent buffer to deal such case.
Reported-by: Stephane Lesimple <stephane_btrfs@lesimple.fr>
Suggested-by: Filipe Manana <fdmanana@kernel.org>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Enable the extended 'limit' syntax (a range), the new 'stripes' and
extended 'usage' syntax (a range) filters in the filters mask. The patch
comes separate and not within the series that introduced the new filters
because the patch adding the mask was merged in a late rc. The
integration branch was based on an older rc and could not merge the
patch due to the missing changes.
Prerequisities:
* btrfs: check unsupported filters in balance arguments
* btrfs: extend balance filter limit to take minimum and maximum
* btrfs: add balance filter for stripes
* btrfs: extend balance filter usage to take minimum and maximum
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Similar to the 'limit' filter, we can enhance the 'usage' filter to
accept a range. The change is backward compatible, the range is applied
only in connection with the BTRFS_BALANCE_ARGS_USAGE_RANGE flag.
We don't have a usecase yet, the current syntax has been sufficient. The
enhancement should provide parity with other range-like filters.
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Balance block groups which have the given number of stripes, defined by
a range min..max. This is useful to selectively rebalance only chunks
that do not span enough devices, applies to RAID0/10/5/6.
Signed-off-by: Gabríel Arthúr Pétursson <gabriel@system.is>
[ renamed bargs members, added to the UAPI, wrote the changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
The 'limit' filter is underdesigned, it should have been a range for
[min,max], with some relaxed semantics when one of the bounds is
missing. Besides that, using a full u64 for a single value is a waste of
bytes.
Let's fix both by extending the use of the u64 bytes for the [min,max]
range. This can be done in a backward compatible way, the range will be
interpreted only if the appropriate flag is set
(BTRFS_BALANCE_ARGS_LIMIT_RANGE).
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
The code for btrfs inode-resolve has never worked properly for
files with enough hard links to trigger extrefs. It was trying to
get the leaf out of a path after freeing the path:
btrfs_release_path(path);
leaf = path->nodes[0];
item_size = btrfs_item_size_nr(leaf, slot);
The fix here is to use the extent buffer we cloned just a little higher
up to avoid deadlocks caused by using the leaf in the path.
Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org # v3.7+
cc: Mark Fasheh <mfasheh@suse.de>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
We don't verify that all the balance filter arguments supplemented by
the flags are actually known to the kernel. Thus we let it silently pass
and do nothing.
At the moment this means only the 'limit' filter, but we're going to add
a few more soon so it's better to have that fixed. Also in older stable
kernels so that it works with newer userspace tools.
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
The commit 1bab0de0274f ("dm-mpath, scsi_dh: don't let dm detach device
handlers") removed reference counting of attached scsi device handler.
As a result, handler data is freed immediately via scsi_dh->detach()
in the context of scsi_remove_device() where activation request can be
still in flight.
This patch moves scsi_dh_handler_detach() to sdev releasing function,
scsi_device_dev_release_usercontext(), at that point the device
is already in quiesced state.
Fixes: 1bab0de0274f ("dm-mpath, scsi_dh: don't let dm detach device handlers")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays
NULL but it's later used in mvs_abort_task as slot which is passed
to mvs_slot_task_free causing NULL pointer dereference.
Just return from mvs_slot_task_free when passed with NULL slot.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891
Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In kernel-doc annotations parameters need to start with a @ for them to be
properly recognized. Add those where missing for virt-dma.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The "compatible" matching algorithm used for looking up old-style
blacklist entries in a scsi_dev_info_list is buggy. The core of the
algorithm looks like this:
if (memcmp(devinfo->vendor, vendor,
min(max, strlen(devinfo->vendor))))
/* not a match */
where max is the length of the device's vendor string after leading
spaces have been removed but trailing spaces have not. Because of the
min() computation, either entry could be a proper substring of the
other and the code would still think that they match.
In the case originally reported, the device's vendor and product
strings were "Inateck " and " ". These matched against
the following entry in the global device list:
{"", "Scanner", "1.80", BLIST_NOLUN}
because "" is a substring of "Inateck " and "" (the result of removing
leading spaces from the device's product string) is a substring of
"Scanner". The mistaken match prevented the system from scanning and
finding the device's second Logical Unit.
This patch fixes the problem by making two changes. First, the code
for leading-space removal is hoisted out of the loop. (This means it
will sometimes run unnecessarily, but since a large percentage of all
lookups involve the "compatible" entries in global device list, this
should be an overall improvement.) Second and more importantly, the
patch removes trailing spaces and adds a check to verify that the two
resulting strings are exactly the same length. This prevents matches
where one entry is a proper substring of the other.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Giulio Bernardi <ugilio@gmail.com>
Tested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In drivers/scsi/scsi_devinfo.c, the scsi_dev_info_list_del_keyed() and
scsi_get_device_flags_keyed() routines contain a large amount of
duplicate code for finding vendor/product matches in a
scsi_dev_info_list. This patch factors out the duplicate code and
puts it in a separate function, scsi_dev_info_list_find().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Hardware manufacturers group keys in the weirdest way possible. This may
cause a power-key to be grouped together with normal keyboard keys and
thus be reported on the same kernel interface.
However, user-space is often only interested in specific sets of events.
For instance, daemons dealing with system-reboot (like systemd-logind)
listen for KEY_POWER, but are not interested in any main keyboard keys.
Usually, power keys are reported via separate interfaces, however,
some i8042 boards report it in the AT matrix. To avoid waking up those
system daemons on each key-press, we had two ideas:
- split off KEY_POWER into a separate interface unconditionally
- allow filtering a specific set of events on evdev FDs
Splitting of KEY_POWER is a rather weird way to deal with this and may
break backwards-compatibility. It is also specific to KEY_POWER and might
be required for other stuff, too. Moreover, we might end up with a huge
set of input-devices just to have them properly split.
Hence, this patchset implements the second idea: An event-mask to specify
which events you're interested in. Two ioctls allow setting this mask for
each event-type. If not set, all events are reported. The type==0 entry is
used same as in EVIOCGBIT to set the actual EV_* mask of filtered events.
This way, you have a two-level filter.
We are heavily forward-compatible to new event-types and event-codes. So
new user-space will be able to run on an old kernel which doesn't know the
given event-codes or event-types.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
the kernel prints some warnings when compiled with CONFIG_DMA_API_DEBUG.
This is because the fnic driver doesn't check the return value of
pci_map_single().
[ 11.942770] scsi host12: fnic
[ 11.950811] ------------[ cut here ]------------
[ 11.950818] WARNING: at lib/dma-debug.c:937 check_unmap+0x47b/0x920()
[ 11.950821] fnic 0000:0c:00.0: DMA-API: device driver failed to check map error[device address=0x0000002020a30040] [size=44 bytes] [mapped as single]
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed By: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Due to wrong assumption in ofpart ofpart fails on Exynos on SPI chips
with no partitions because the subnode containing controller data
confuses the ofpart parser.
Thus compiling in ofpart support automatically fails probing any SPI NOR
flash without partitions on Exynos.
Compiling in a partitioning scheme should not cause probe of otherwise
valid device to fail.
Instead, let's do the following:
* try parsers until one succeeds
* if no parser succeeds, report the first error we saw
* even in the failure case, allow MTD to probe, with fallback
partitions or no partitions at all -- the master device will still be
registered
Issue report and comments initially by Michal Suchanek.
Reported-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
We would like to get the following updates in:
Revert ownership to "Emulex" from "Avago Technologies"
Signed-off-by: Ketan Mukadam <ketan.mukadam@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Ketan Mukadam <ketan.mukadam@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Sergei Shtylyov says:
====================
sh_eth: RX buffer alignment fixes
Here's a set of 2 patches against DaveM's 'net.git' repo which are the
fixes to the RX buffer size calculation.
[1/2] sh_eth: fix RX buffer size alignment
[2/2] sh_eth: fix RX buffer size calculation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RX buffer size calulation failed to account for the length granularity
(which is now 32 bytes)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both Renesas R-Car and RZ/A1 manuals state that RX buffer length must be
a multiple of 32 bytes, while the driver only uses 16 byte granularity...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not log error for netevents that need no action such as
NETDEV_REGISTER 0x0005, NETDEV_CHANGEADDR, and NETDEV_CHANGENAME.
It results in logging error messages such as these
[ 35.315872] bnx2fc: Unknown netevent 5
[ 35.315935] bnx2fc: Unknown netevent 8
[ 35.353866] bnx2fc: Unknown netevent 10
and generating bug reports.
Remove logging this message as an ERROR instead of turning them into
either DEBUG or INFO level messages.
Signed-off-by: Shirish Pargaonkar <spargaonkar@suse.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
With the old binding and driver architecture we had many issues:
No way to assign eDMA channels to event queues, thus not able to tune the
system by moving specific DMA channels to low/high priority servicing. We
moved the cyclic channels to high priority within the code, but that was
just a workaround to this issue.
Memcopy was fundamentally broken: even if the driver scanned the DT/devices
in the booted system for direct DMA users (which is not effective when the
events are going through a crossbar) and created a map of 'used' channels,
this information was not really usable. Since via dmaengien API the eDMA
driver will be called with _some_ channel number, we would try to request
this channel when any channel is requested for memcpy. By luck we got
channel which is not used by any device most of the time so things worked,
but if a device would have been using the given channel, but not requested
it, the memcpy channel would have been waiting for HW event.
The old code had the am33xx/am43xx DMA event router handling embedded. This
should have been done in a separate driver since it is not part of the
actual eDMA IP.
There were no way to 'lock' PaRAM slots to be used by the DSP for example
when booting with DT.
In DT boot the edma node used more than one hwmod which is not a good
practice and the kernel prints warning because of this.
With the new bindings and the changes in the driver we can:
- No regression with Legacy binding and non DT boot
- DMA channels can be assigned to any TC (to set priority)
- PaRAM slots can be reserved for other cores to use
- Dynamic power management for CC and TCs, if only TC0 is used all other TC
can be powered down for example
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since the crossbar is needed for eDMA when it is used on OMAP like
platforms (am335x/am437x and later DRA7xx), select the crossbar to be built
if ARCH_OMAP is set.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The DMA event crossbar on AM33xx/AM43xx is different from the one found in
DRA7x family.
Instead of a single event crossbar it has 64 identical mux attached to each
eDMA event line. When the 0 event mux is selected, the default mapped event
is going to be routed to the corresponding eDMA event line. If different
mux is selected, then the selected event is going to be routed to the given
eDMA event.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Instead of nesting functions just merge them since the resulting function
is still small and readable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The channel/slot reservation is not supported when booted with DT so there
is not need to allocate memory.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Move all code under one function to do the dma device and eDMA channel
related setup so they are not scattered around the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Query the number of qDMA channels from CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
edma_assign_channel_eventq() is a wrapper around edma_map_dmach_to_queue()
We can merge the content of the later so we will have only one function
to be used for mapping channels to given eventq
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
These inline functions are designed to modify parts of the PaRAM in eDMA.
Change the names accordingly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Instead of passing a pointer to struct edma_cc and the channel number,
pass only the pointer to the edma_chan structure for the given channel.
This struct contains all the information needed by the functions and the
use of this makes it obvious that most of the sanity checks can be removed
from the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If the transfer is shorted then 64K we can complete it with one ACNT burst
by configuring ACNT to the length of the copy, this require one paRAM slot.
Otherwise we use two paRAM slots for the copy:
slot1: will copy (length / 32767) number of 32767 byte long blocks
slot2: will be configured to copy the remaining data.
According to tests this patch increases the throughput of memcpy from
~3MB/s to 15MB/s
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Despite the claim by the original commit adding the memcpy
support, eDMA does not have constraint on the alignment of src, dst
or length in increment mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Initial link up defaults were not properly being tracked relative to
initial FLOGI or pt2pt PLOGI. Add code to initialize them.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Forgot to clear FCF Discovery in-progress flag upon FLOGI failures.
Thus we didn't restart FLOGI.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
aborted
Fix for discovery failure in PT2PT when FLOGI's ELS ACC response gets aborted
Change login state machine to:
- Restart FLOGI if prior is ABTS'd
- Reject incoming FLOGIs if we have one pending
The above ensures that we always finish FLOGI processing, regardless
of who initated FLOGI, before processing PLOGI's.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lpfc_send_rscn_event() allocates data for sizeof(struct
lpfc_rscn_event_header) + payload_len, but claims that the data has size
of sizeof(struct lpfc_els_event_header) + payload_len. That leads to
buffer overruns.
Signed-off-by: Ales Novak <alnovak@suse.cz>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
