| Age | Commit message (Collapse) | Author |
|---|
|
Because we write pipestat before iir, it's possible that a pipestat
interrupt will occur between the pipestat write and the iir write. This
leaves pipestat with an interrupt status not visible in iir. This may cause
an interrupt flood as we never clear the pipestat event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The old code was wandering through the active list looking for pinned
buffers; there may be other pinned buffers around. Fortunately, we keep a
count of the total amount of pinned memory and can use that instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Instead, just warn that bad things are happening and do our best to clean up
the mess without the GPU's help.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The IMR masking was a technique recommended for avoiding getting stuck with
no interrupts generated again in MSI mode. It kept new IIR bits from getting
set between the IIR read and the IIR write, which would have otherwise
prevented an MSI from ever getting generated again. However, this caused a
problem for vblank as the IMR mask would keep the pipe event interrupt from
getting reflected in IIR, even after the IMR mask was brought back down.
Instead, just check the state of IIR after we ack the interrupts we're going
to handle, and restart if we didn't get IIR all the way to zero.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
ml_ff_playback() uses spin_(un)lock_bh. However this function is
called with interrupts disabled from erase_effect() in
drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom
half handling code. This patch changes this function to just use
spin_lock_irqsave() instead, solving the problem and simplifying
the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Often we do things like put BUG() in the default clause of a case
statement. Since it was not declared __noreturn, this could sometimes
lead to bogus compiler warnings that variables were used
uninitialized.
There is a small problem in that we have to put a magic while(1); loop to
fool GCC into really thinking it is noreturn. This makes the new
BUG() function 3 instructions long instead of just 1, but I think it
is worth it as it is now unnecessary to do extra work to silence the
'used uninitialized' warnings.
I also re-wrote BUG_ON so that if it is given a constant condition, it
just does BUG() instead of loading a constant value in to a register
and testing it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Instead of using a spinlock, it is better to call the proper pcm stream
locking schema.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
New firmware image brings enhanced tuning performance.
Firmware is available for download at the following location:
http://www.steventoth.net/linux/sms1xxx
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The video device was part of the gspca device. On device disconnection
while streaming, the device structure is freed at close time.
In this case, the remaining close job on the video device run out of
allocated memory.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The previous subdriver protection against rmmod was done via the
file operations table in the device descriptor. On device disconnection
while streaming, the device structure was freed at close time, and the
module_put still used the module name in the freed area.
Now, explicit module get/put are done on open and close.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As a side effect, the sd routine stop0 is called on disconnect.
This permits the subdriver to free its resources.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jk/spufs into merge
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx into merge
|
|
|
|
Impact: update documentation
Update to reflect the current state of the tracing framework:
- "none" tracer has been replaced by "nop" tracer
- tracing_enabled must be toggled when changing buffer size
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix mmiotrace overrun tracing
When ftrace framework moved to use the ring buffer facility, the buffer
overrun detection was broken after 2.6.27 by commit
| commit 3928a8a2d98081d1bc3c0a84a2d70e29b90ecf1c
| Author: Steven Rostedt <rostedt@goodmis.org>
| Date: Mon Sep 29 23:02:41 2008 -0400
|
| ftrace: make work with new ring buffer
|
| This patch ports ftrace over to the new ring buffer.
The detection is now fixed by using the ring buffer API.
When mmiotrace detects a buffer overrun, it will report the number of
lost events. People reading an mmiotrace log must know if something was
missed, otherwise the data may not make sense.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
the use of is_blah() suggests a 1 or 0 return. This assumption is made in
pxa25x_udc code such as:
dev->vbus = is_vbus_present();
where dev->vbus is a bitfield. This fix allows pxa25x_udc_probe to correctly
detect vbus. Other changes were to make its use consistent in the rest of
the code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Impact: fix Xen guest boot failure
commit eefb47f6a1e855653d275cb90592a3587ea93a09 ("xen: use
spin_lock_nest_lock when pinning a pagetable") changed xen_pgd_walk to
walk over mm->pgd rather than taking pgd as an argument.
This breaks xen_mm_(un)pin_all() because it makes init_mm.pgd readonly
instead of the pgd we are interested in and therefore the pin subsequently
fails.
(XEN) mm.c:2280:d15 Bad type (saw 00000000e8000001 != exp 0000000060000000) for mfn bc464 (pfn 21ca7)
(XEN) mm.c:2665:d15 Error while pinning mfn bc464
[ 14.586913] 1 multicall(s) failed: cpu 0
[ 14.586926] Pid: 14, comm: kstop/0 Not tainted 2.6.28-rc5-x86_32p-xenU-00172-gee2f6cc #200
[ 14.586940] Call Trace:
[ 14.586955] [<c030c17a>] ? printk+0x18/0x1e
[ 14.586972] [<c0103df3>] xen_mc_flush+0x163/0x1d0
[ 14.586986] [<c0104bc1>] __xen_pgd_pin+0xa1/0x110
[ 14.587000] [<c015a330>] ? stop_cpu+0x0/0xf0
[ 14.587015] [<c0104d7b>] xen_mm_pin_all+0x4b/0x70
[ 14.587029] [<c022bcb9>] xen_suspend+0x39/0xe0
[ 14.587042] [<c015a330>] ? stop_cpu+0x0/0xf0
[ 14.587054] [<c015a3cd>] stop_cpu+0x9d/0xf0
[ 14.587067] [<c01417cd>] run_workqueue+0x8d/0x150
[ 14.587080] [<c030e4b3>] ? _spin_unlock_irqrestore+0x23/0x40
[ 14.587094] [<c014558a>] ? prepare_to_wait+0x3a/0x70
[ 14.587107] [<c0141918>] worker_thread+0x88/0xf0
[ 14.587120] [<c01453c0>] ? autoremove_wake_function+0x0/0x50
[ 14.587133] [<c0141890>] ? worker_thread+0x0/0xf0
[ 14.587146] [<c014509c>] kthread+0x3c/0x70
[ 14.587157] [<c0145060>] ? kthread+0x0/0x70
[ 14.587170] [<c0109d1b>] kernel_thread_helper+0x7/0x10
[ 14.587181] call 1/3: op=14 arg=[c0415000] result=0
[ 14.587192] call 2/3: op=14 arg=[e1ca2000] result=0
[ 14.587204] call 3/3: op=26 arg=[c1808860] result=-22
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile into x86/urgent
|
|
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Impact: fix MSIx not enough irq numbers available regression
The manual revert of the sparse_irq patches missed to bring the number
of possible irqs back to the .27 status. This resulted in a regression
when two multichannel network cards were placed in a system with only
one IO_APIC - causing the networking driver to not have the right
IRQ and the device not coming up.
Remove the dynamic allocation logic leftovers and simply return
NR_IRQS in probe_nr_irqs() for now.
Fixes: http://lkml.org/lkml/2008/11/19/354
Reported-by: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jesper Dangaard Brouer <hawk@diku.dk>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix kernel-doc build
Fix missing & excess irq.h kernel-doc:
Warning(include/linux/irq.h:182): No description found for parameter 'irq'
Warning(include/linux/irq.h:182): Excess struct/union/enum/typedef member 'affinity_entry' description in 'irq_desc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
|
|
|
|
Impact: prettify /proc/lockdep_info
Just feel odd that not all lines of lockdep info are aligned.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: make output of stack_trace complete if buffer overruns
When read buffer overruns, the output of stack_trace isn't complete.
When printing records with seq_printf in t_show, if the read buffer
has overruned by the current record, then this record won't be
printed to user space through read buffer, it will just be dropped in
this printing.
When next printing, t_start should return the "*pos"th record, which
is the one dropped by previous printing, but it just returns
(m->private + *pos)th record.
Here we use a more sane method to implement seq_operations which can
be found in kernel code. Thus we needn't initialize m->private.
About testing, it's not easy to overrun read buffer, but we can use
seq_printf to print more padding bytes in t_show, then it's easy to
check whether or not records are lost.
This commit has been tested on both condition of overrun and non
overrun.
Signed-off-by: Liming Wang <liming.wang@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
Added the matching model=dell-m6 for Dell Studio 15 laptop.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added STAC_DELL_M4_3 quirk for Dell systems, also reorganized the
board config switch to assign number of digital muxes, microphones,
and SPDIF muxes via the PCI quirk defined.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the following sparse warnings:
sound/sound_core.c:460:2: warning: returning void-valued expression
sound/sound_core.c:477:2: warning: returning void-valued expression
sound/sound_core.c:510:5: warning: symbol 'soundcore_open' was not
declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
|
|
|
|
Currently, we can end up in an infinite loop if we get a signal
while the kernel has faulted in spufs_ps_fault. Eg:
alarm(1);
write(fd, some_spu_psmap_register_address, 4);
- the write's copy_from_user will fault on the ps mapping, and
signal_pending will be non-zero. Because returning from the fault
handler will never clear TIF_SIGPENDING, so we'll just keep faulting,
resulting in an unkillable process using 100% of CPU.
This change returns VM_FAULT_SIGBUS if there's a fatal signal pending,
letting us escape the loop.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] xen: fix xen_get_eflags.
[IA64] ia64/pv_ops/pv_cpu_ops: fix _IA64_REG_IP case.
[IA64] remove duplicate include iommu.h
[IA64] use mprintk instead of printk, in ia64_mca_modify_original_stack
[IA64] Rationalize kernel mode alignment checking
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ACE1001 patch for cp2101.c
USB: usbmon: fix read(2)
USB: gadget rndis: send notifications
USB: gadget rndis: stop windows self-immolation
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
USB: storage: updates unusual_devs entry for the Nokia 6300
usb: musb: fix bug in musb_schedule
USB: fix SB700 usb subsystem hang bug
|
|
fix xen_get_eflags. It doesn't take any argument.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
arch/ia64/kernel/pci-dma.c only needs to include iommu once.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Using printk from MCA/INIT context is unsafe since it can cause deadlock.
The ia64_mca_modify_original_stack is called from both of mca handler and
init handler, so it should use mprintk instead of printk.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Itanium processors can handle some misaligned data accesses. They
also provide a mode where all such accesses are forced to trap. The
kernel was schizophrenic about use of this mode:
* Base kernel code ran in permissive mode where the only traps
generated were from those cases that the h/w could not handle.
* Interrupt, syscall and trap code ran in strict mode where all
unaligned accesses caused traps to the 0x5a00 unaligned reference
vector.
Use strict alignment checking throughout the kernel, but make
sure that we continue to let user mode use more relaxed mode
as the default.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
When we migrate an interrupt from one CPU to another, we set the
move_in_progress flag and clean up the vectors later once they're not
being used. If you're unlucky and call destroy_irq() before the vectors
become un-used, the move_in_progress flag is never cleared, which causes
the interrupt to become unusable.
This was discovered by Jesse Brandeburg for whom it manifested as an
MSI-X device refusing to use MSI-X mode when the driver was unloaded
and reloaded repeatedly.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a regression reported by Max Kellermann whereby kernel profiling
showed that his clients were spending 45% of their time in
rpcauth_lookup_credcache.
It turns out that although his processes had identical uid/gid/groups,
generic_match() was failing to detect this, because the task->group_info
pointers were not shared. This again lead to the creation of a huge number
of identical credentials at the RPC layer.
The regression is fixed by comparing the contents of task->group_info
if the actual pointers are not identical.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Do not attempt to close invalidated file handles
[CIFS] fix check for dead tcon in smb_init
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: csrc-r4k: Fix declaration depending on the wrong CONFIG_ symbol.
MIPS: csrc-r4k: Fix spelling mistake.
MIPS: RB532: Provide functions for gpio configuration
MIPS: IP22: Make indy_sc_ops variable static
MIPS: RB532: GPIO register offsets are relative to GPIOBASE
MIPS: Malta: Fix include paths in malta-amon.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
intel-iommu: fix compile warnings
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
net: fix tiny output corruption of /proc/net/snmp6
atl2: don't request irq on resume if netif running
ipv6: use seq_release_private for ip6mr.c /proc entries
pkt_sched: fix missing check for packet overrun in qdisc_dump_stab()
smc911x: Fix printf format typo in smc911x driver.
asix: Fix asix-based cards connecting to 10/100Mbs LAN.
mv643xx_eth: fix recycle check bound
mv643xx_eth: fix the order of mdiobus_{unregister, free}() calls
sh: sh_eth: Update to change of mii_bus
TPROXY: supply a struct flowi->flags argument in inet_sk_rebuild_header()
TPROXY: fill struct flowi->flags in udp_sendmsg()
net: ipg.c fix bracing on endian swapping
phylib: Fix auto-negotiation restart avoidance
net: jme.c rxdesc.flags is __le16, other missing endian swaps
phylib: fix phy name example in documentation
net: Do not fire linkwatch events until the device is registered.
phonet: fix compilation with gcc-3.4
ixgbe: fix compilation with gcc-3.4
pktgen: fix multiple queue warning
net: fix ip_mr_init() error path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: fix dyn ftrace filter selection
ftrace: make filtered functions effective on setting
ftrace: fix set_ftrace_filter
trace: introduce missing mutex_unlock()
tracing: kernel/trace/trace.c: introduce missing kfree()
|
