| Age | Commit message (Collapse) | Author |
|---|
|
The RX rings have a producer index owned by hardware, where newly
received frame buffers are placed, and a consumer index owned by
software, where newly allocated buffers are placed, in expectation of
hardware being able to place frame data in them.
Hardware increments the producer index when a frame is received, however
it is not allowed to increment the producer index to match the consumer
index (RBCIR) since the ring can hold at most RBLENR[LENGTH]-1 received
BDs. Whenever the producer index matches the value of the consumer
index, the ring has no unprocessed received frames and all BDs in the
ring have been initialized/prepared by software, i.e. hardware owns all
BDs in the ring.
The code uses the next_to_clean variable to keep track of the producer
index, and the next_to_use variable to keep track of the consumer index.
The RX rings are seeded from enetc_refill_rx_ring, which is called from
two places:
1. initially the ring is seeded until full with enetc_bd_unused(rx_ring),
i.e. with 511 buffers. This will make next_to_clean=0 and next_to_use=511:
.ndo_open
-> enetc_open
-> enetc_setup_bdrs
-> enetc_setup_rxbdr
-> enetc_refill_rx_ring
2. then during the data path processing, it is refilled with 16 buffers
at a time:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_clean_rx_ring
-> enetc_refill_rx_ring
There is just one problem: the initial seeding done during .ndo_open
updates just the producer index (ENETC_RBPIR) with 0, and the software
next_to_clean and next_to_use variables. Notably, it will not update the
consumer index to make the hardware aware of the newly added buffers.
Wait, what? So how does it work?
Well, the reset values of the producer index and of the consumer index
of a ring are both zero. As per the description in the second paragraph,
it means that the ring is full of buffers waiting for hardware to put
frames in them, which by coincidence is almost true, because we have in
fact seeded 511 buffers into the ring.
But will the hardware attempt to access the 512th entry of the ring,
which has an invalid BD in it? Well, no, because in order to do that, it
would have to first populate the first 511 entries, and the NAPI
enetc_poll will kick in by then. Eventually, after 16 processed slots
have become available in the RX ring, enetc_clean_rx_ring will call
enetc_refill_rx_ring and then will [ finally ] update the consumer index
with the new software next_to_use variable. From now on, the
next_to_clean and next_to_use variables are in sync with the producer
and consumer ring indices.
So the day is saved, right? Well, not quite. Freeing the memory
allocated for the rings is done in:
enetc_close
-> enetc_clear_bdrs
-> enetc_clear_rxbdr
-> this just disables the ring
-> enetc_free_rxtx_rings
-> enetc_free_rx_ring
-> sets next_to_clean and next_to_use to 0
but again, nothing is committed to the hardware producer and consumer
indices (yay!). The assumption is that the ring is disabled, so the
indices don't matter anyway, and it's the responsibility of the "open"
code path to set those up.
.. Except that the "open" code path does not set those up properly.
While initially, things almost work, during subsequent enetc_close ->
enetc_open sequences, we have problems. To be precise, the enetc_open
that is subsequent to enetc_close will again refill the ring with 511
entries, but it will leave the consumer index untouched. Untouched
means, of course, equal to the value it had before disabling the ring
and draining the old buffers in enetc_close.
But as mentioned, enetc_setup_rxbdr will at least update the producer
index though, through this line of code:
enetc_rxbdr_wr(hw, idx, ENETC_RBPIR, 0);
so at this stage we'll have:
next_to_clean=0 (in hardware 0)
next_to_use=511 (in hardware we'll have the refill index prior to enetc_close)
Again, the next_to_clean and producer index are in sync and set to
correct values, so the driver manages to limp on. Eventually, 16 ring
entries will be consumed by enetc_poll, and the savior
enetc_clean_rx_ring will come and call enetc_refill_rx_ring, and then
update the hardware consumer ring based upon the new next_to_use.
So.. it works?
Well, by coincidence, it almost does, but there's a circumstance where
enetc_clean_rx_ring won't be there to save us. If the previous value of
the consumer index was 15, there's a problem, because the NAPI poll
sequence will only issue a refill when 16 or more buffers have been
consumed.
It's easiest to illustrate this with an example:
ip link set eno0 up
ip addr add 192.168.100.1/24 dev eno0
ping 192.168.100.1 -c 20 # ping this port from another board
ip link set eno0 down
ip link set eno0 up
ping 192.168.100.1 -c 20 # ping it again from the same other board
One by one:
1. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 0)
2. ping 192.168.100.1 -c 20 # ping this port from another board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=15 next_to_clean 14 (in hw 15) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: enetc_refill_rx_ring(16) increments next_to_use by 16 (mod 512) and writes it to hw
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=0 next_to_clean 15 (in hw 16) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 16 (in hw 17) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 17 (in hw 18) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 18 (in hw 19) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 19 (in hw 20) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 20 (in hw 21) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 21 (in hw 22) next_to_use 15 (in hw 15)
20 packets transmitted, 20 packets received, 0% packet loss
3. ip link set eno0 down
enetc_free_rx_ring: next_to_clean 0 (in hw 22), next_to_use 0 (in hw 15)
4. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 15)
5. ping 192.168.100.1 -c 20 # ping it again from the same other board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 15)
20 packets transmitted, 12 packets received, 40% packet loss
And there it dies. No enetc_refill_rx_ring (because cleaned_cnt must be equal
to 15 for that to happen), no nothing. The hardware enters the condition where
the producer (14) + 1 is equal to the consumer (15) index, which makes it
believe it has no more free buffers to put packets in, so it starts discarding
them:
ip netns exec ns0 ethtool -S eno0 | grep -v ': 0'
NIC statistics:
Rx ring 0 discarded frames: 8
Summarized, if the interface receives between 16 and 32 (mod 512) frames
and then there is a link flap, then the port will eventually die with no
way to recover. If it receives less than 16 (mod 512) frames, then the
initial NAPI poll [ before the link flap ] will not update the consumer
index in hardware (it will remain zero) which will be ok when the buffers
are later reinitialized. If more than 32 (mod 512) frames are received,
the initial NAPI poll has the chance to refill the ring twice, updating
the consumer index to at least 32. So after the link flap, the consumer
index is still wrong, but the post-flap NAPI poll gets a chance to
refill the ring once (because it passes through cleaned_cnt=15) and
makes the consumer index be again back in sync with next_to_use.
The solution to this problem is actually simple, we just need to write
next_to_use into the hardware consumer index at enetc_open time, which
always brings it back in sync after an initial buffer seeding process.
The simpler thing would be to put the write to the consumer index into
enetc_refill_rx_ring directly, but there are issues with the MDIO
locking: in the NAPI poll code we have the enetc_lock_mdio() taken from
top-level and we use the unlocked enetc_wr_reg_hot, whereas in
enetc_open, the enetc_lock_mdio() is not taken at the top level, but
instead by each individual enetc_wr_reg, so we are forced to put an
additional enetc_wr_reg in enetc_setup_rxbdr. Better organization of
the code is left as a refactoring exercise.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Station Interface Receive Interrupt Detect Register (SIRXIDR)
contains a 16-bit wide mask of 'interrupt detected' events for each ring
associated with a port. Bit i is write-1-to-clean for RX ring i.
I have no explanation whatsoever how this line of code came to be
inserted in the blamed commit. I checked the downstream versions of that
patch and none of them have it.
The somewhat comical aspect of it is that we're writing a binary number
to the SIRXIDR register, which is derived from enetc_bd_unused(rx_ring).
Since the RX rings have 512 buffer descriptors, we end up writing 511 to
this register, which is 0x1ff, so we are effectively clearing the
'interrupt detected' event for rings 0-8.
This register is not what is used for interrupt handling though - it
only provides a summary for the entire SI. The hardware provides one
separate Interrupt Detect Register per RX ring, which auto-clears upon
read. So there doesn't seem to be any adverse effect caused by this
bogus write.
There is, however, one reason why this should be handled as a bugfix:
next_to_clean _should_ be committed to hardware, just not to that
register, and this was obscuring the fact that it wasn't. This is fixed
in the next patch, and removing the bogus line now allows the fix patch
to be backported beyond that point.
Fixes: fd5736bf9f23 ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ENETC port 0 MAC supports in-band status signaling coming from a PHY
when operating in RGMII mode, and this feature is enabled by default.
It has been reported that RGMII is broken in fixed-link, and that is not
surprising considering the fact that no PHY is attached to the MAC in
that case, but a switch.
This brings us to the topic of the patch: the enetc driver should have
not enabled the optional in-band status signaling for RGMII unconditionally,
but should have forced the speed and duplex to what was resolved by
phylink.
Note that phylink does not accept the RGMII modes as valid for in-band
signaling, and these operate a bit differently than 1000base-x and SGMII
(notably there is no clause 37 state machine so no ACK required from the
MAC, instead the PHY sends extra code words on RXD[3:0] whenever it is
not transmitting something else, so it should be safe to leave a PHY
with this option unconditionally enabled even if we ignore it). The spec
talks about this here:
https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/138/RGMIIv1_5F00_3.pdf
Fixes: 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quoting from the blamed commit:
In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Intuitive or not, there isn't any definition issued by a standards body
which says that promiscuity has anything to do with VLAN filtering - it
only has to do with accepting packets regardless of destination MAC address.
In fact people are already trying to use this misunderstanding/bug of
the enetc driver as a justification to transform promiscuity into
something it never was about: accepting every packet (maybe that would
be the "rx-all" netdev feature?):
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
This is relevant because there are use cases in the kernel (such as
tc-flower rules with the protocol 802.1Q and a vlan_id key) which do not
(yet) use the vlan_vid_add API to be compatible with VLAN-filtering NICs
such as enetc, so for those, disabling rx-vlan-filter is currently the
only right solution to make these setups work:
https://lore.kernel.org/netdev/CA+h21hoxwRdhq4y+w8Kwgm74d4cA0xLeiHTrmT-VpSaM7obhkg@mail.gmail.com/
The blamed patch has unintentionally introduced one more way for this to
work, which is to enable IFF_PROMISC, however this is non-portable
because port promiscuity is not meant to disable VLAN filtering.
Therefore, it could invite people to write broken scripts for enetc, and
then wonder why they are broken when migrating to other drivers that
don't handle promiscuity in the same way.
Fixes: 7070eea5e95a ("enetc: permit configuration of rx-vlan-filter with ethtool")
Cc: Markus Blöchl <Markus.Bloechl@ipetronik.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the enetc ports have rx-vlan-offload enabled, they report a TPID of
ETH_P_8021Q regardless of what was actually in the packet. When
rx-vlan-offload is disabled, packets have the proper TPID. Fix this
inconsistency by finishing the TODO left in the code.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The workaround for the ENETC MDIO erratum caused a performance
degradation of 82 Kpps (seen with IP forwarding of two 1Gbps streams of
64B packets). This is due to excessive locking and unlocking in the fast
path, which can be avoided.
By taking the MDIO read-side lock only once per NAPI poll cycle, we are
able to regain 54 Kpps (65%) of the performance hit. The rest of the
performance degradation comes from the TX data path, but unfortunately
it doesn't look like we can optimize that away easily, even with
netdev_xmit_more(), there just isn't any skb batching done, to help with
taking the MDIO lock less often than once per packet.
We need to change the register accessor type for enetc_get_tx_tstamp,
because it now runs under the enetc_lock_mdio as per the new call path
detailed below:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_lock_mdio
-> enetc_clean_tx_ring
-> enetc_get_tx_tstamp
-> enetc_clean_rx_ring
-> enetc_unlock_mdio
Fixes: fd5736bf9f23 ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael reports that since linux-next-20210211, the AER messages for ECC
errors have started reappearing, and this time they can be reliably
reproduced with the first ping on one of his LS1028A boards.
$ ping 1[ 33.258069] pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
72.16.0.1
PING [ 33.267050] pcieport 0000:00:1f.0: AER: can't find device of ID0000
172.16.0.1 (172.16.0.1): 56 data bytes
64 bytes from 172.16.0.1: seq=0 ttl=64 time=17.124 ms
64 bytes from 172.16.0.1: seq=1 ttl=64 time=0.273 ms
$ devmem 0x1f8010e10 32
0xC0000006
It isn't clear why this is necessary, but it seems that for the errors
to go away, we must clear the entire RFS and RSS memory, not just for
the ports in use.
Sadly the code is structured in such a way that we can't have unified
logic for the used and unused ports. For the minimal initialization of
an unused port, we need just to enable and ioremap the PF memory space,
and a control buffer descriptor ring. Unused ports must then free the
CBDR because the driver will exit, but used ports can not pick up from
where that code path left, since the CBDR API does not reinitialize a
ring when setting it up, so its producer and consumer indices are out of
sync between the software and hardware state. So a separate
enetc_init_unused_port function was created, and it gets called right
after the PF memory space is enabled.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Reported-by: Michael Walle <michael@walle.cc>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the blamed patch, all RX traffic gets hashed to CPU 0 because the
hashing indirection table set up in:
enetc_pf_probe
-> enetc_alloc_si_resources
-> enetc_configure_si
-> enetc_setup_default_rss_table
is overwritten later in:
enetc_pf_probe
-> enetc_init_port_rss_memory
which zero-initializes the entire port RSS table in order to avoid ECC errors.
The trouble really is that enetc_init_port_rss_memory really neads
enetc_alloc_si_resources to be called, because it depends upon
enetc_alloc_cbdr and enetc_setup_cbdr. But that whole enetc_configure_si
thing could have been better thought out, it has nothing to do in a
function called "alloc_si_resources", especially since its counterpart,
"free_si_resources", does nothing to unwind the configuration of the SI.
The point is, we need to pull out enetc_configure_si out of
enetc_alloc_resources, and move it after enetc_init_port_rss_memory.
This allows us to set up the default RSS indirection table after
initializing the memory.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In inet_initpeers(), struct inet_peer on IA32 uses 128 bytes in nowdays.
Get rid of the cascade and use div64_ul() and clamp_val() calculate that
will not need to be adjusted in the future as suggested by Eric Dumazet.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot found WARNING in __alloc_pages_nodemask()[1] when order >= MAX_ORDER.
It was caused by a huge length value passed from userspace to qrtr_tun_write_iter(),
which tries to allocate skb. Since the value comes from the untrusted source
there is no need to raise a warning in __alloc_pages_nodemask().
[1] WARNING in __alloc_pages_nodemask+0x5f8/0x730 mm/page_alloc.c:5014
Call Trace:
__alloc_pages include/linux/gfp.h:511 [inline]
__alloc_pages_node include/linux/gfp.h:524 [inline]
alloc_pages_node include/linux/gfp.h:538 [inline]
kmalloc_large_node+0x60/0x110 mm/slub.c:3999
__kmalloc_node_track_caller+0x319/0x3f0 mm/slub.c:4496
__kmalloc_reserve net/core/skbuff.c:150 [inline]
__alloc_skb+0x4e4/0x5a0 net/core/skbuff.c:210
__netdev_alloc_skb+0x70/0x400 net/core/skbuff.c:446
netdev_alloc_skb include/linux/skbuff.h:2832 [inline]
qrtr_endpoint_post+0x84/0x11b0 net/qrtr/qrtr.c:442
qrtr_tun_write_iter+0x11f/0x1a0 net/qrtr/tun.c:98
call_write_iter include/linux/fs.h:1901 [inline]
new_sync_write+0x426/0x650 fs/read_write.c:518
vfs_write+0x791/0xa30 fs/read_write.c:605
ksys_write+0x12d/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported-by: syzbot+80dccaee7c6630fa9dcf@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sergey Shtylyov says:
====================
Fix TRSCER masks in the Ether driver
Here are 3 patches against DaveM's 'net' repo. I'm fixing the TRSCER masks in
the driver to match the manuals...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the RZ/A2M Group User's Manual: Hardware, Rev. 2.00,
the TRSCER register has bit 9 reserved, hence we can't use the driver's
default TRSCER mask. Add the explicit initializer for sh_eth_cpu_data::
trscer_err_mask for R7S9210.
Fixes: 6e0bb04d0e4f ("sh_eth: Add R7S9210 support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d313 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver. Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...
Fixes: 86a74ff21a7a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lanai_dev_open() can fail. When it fail, lanai->base is unmapped and the
pci device is disabled. The caller, lanai_init_one(), then tries to run
atm_dev_deregister(). This will subsequently call lanai_dev_close() and
use the already released MMIO area.
To fix this issue, set the lanai->base to NULL if open fail,
and test the flag in lanai_dev_close().
[ 8.324153] lanai: lanai_start() failed, err=19
[ 8.324819] lanai(itf 0): shutting down interface
[ 8.325211] BUG: unable to handle page fault for address: ffffc90000180024
[ 8.325781] #PF: supervisor write access in kernel mode
[ 8.326215] #PF: error_code(0x0002) - not-present page
[ 8.326641] PGD 100000067 P4D 100000067 PUD 100139067 PMD 10013a067 PTE 0
[ 8.327206] Oops: 0002 [#1] SMP KASAN NOPTI
[ 8.327557] CPU: 0 PID: 95 Comm: modprobe Not tainted 5.11.0-rc7-00090-gdcc0b49040c7 #12
[ 8.328229] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd9c812dda519-4
[ 8.329145] RIP: 0010:lanai_dev_close+0x4f/0xe5 [lanai]
[ 8.329587] Code: 00 48 c7 c7 00 d3 01 c0 e8 49 4e 0a c2 48 8d bd 08 02 00 00 e8 6e 52 14 c1 48 80
[ 8.330917] RSP: 0018:ffff8881029ef680 EFLAGS: 00010246
[ 8.331196] RAX: 000000000003fffe RBX: ffff888102fb4800 RCX: ffffffffc001a98a
[ 8.331572] RDX: ffffc90000180000 RSI: 0000000000000246 RDI: ffff888102fb4000
[ 8.331948] RBP: ffff888102fb4000 R08: ffffffff8115da8a R09: ffffed102053deaa
[ 8.332326] R10: 0000000000000003 R11: ffffed102053dea9 R12: ffff888102fb48a4
[ 8.332701] R13: ffffffffc00123c0 R14: ffff888102fb4b90 R15: ffff888102fb4b88
[ 8.333077] FS: 00007f08eb9056a0(0000) GS:ffff88815b400000(0000) knlGS:0000000000000000
[ 8.333502] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8.333806] CR2: ffffc90000180024 CR3: 0000000102a28000 CR4: 00000000000006f0
[ 8.334182] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8.334557] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8.334932] Call Trace:
[ 8.335066] atm_dev_deregister+0x161/0x1a0 [atm]
[ 8.335324] lanai_init_one.cold+0x20c/0x96d [lanai]
[ 8.335594] ? lanai_send+0x2a0/0x2a0 [lanai]
[ 8.335831] local_pci_probe+0x6f/0xb0
[ 8.336039] pci_device_probe+0x171/0x240
[ 8.336255] ? pci_device_remove+0xe0/0xe0
[ 8.336475] ? kernfs_create_link+0xb6/0x110
[ 8.336704] ? sysfs_do_create_link_sd.isra.0+0x76/0xe0
[ 8.336983] really_probe+0x161/0x420
[ 8.337181] driver_probe_device+0x6d/0xd0
[ 8.337401] device_driver_attach+0x82/0x90
[ 8.337626] ? device_driver_attach+0x90/0x90
[ 8.337859] __driver_attach+0x60/0x100
[ 8.338065] ? device_driver_attach+0x90/0x90
[ 8.338298] bus_for_each_dev+0xe1/0x140
[ 8.338511] ? subsys_dev_iter_exit+0x10/0x10
[ 8.338745] ? klist_node_init+0x61/0x80
[ 8.338956] bus_add_driver+0x254/0x2a0
[ 8.339164] driver_register+0xd3/0x150
[ 8.339370] ? 0xffffffffc0028000
[ 8.339550] do_one_initcall+0x84/0x250
[ 8.339755] ? trace_event_raw_event_initcall_finish+0x150/0x150
[ 8.340076] ? free_vmap_area_noflush+0x1a5/0x5c0
[ 8.340329] ? unpoison_range+0xf/0x30
[ 8.340532] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 8.340806] ? unpoison_range+0xf/0x30
[ 8.341014] ? unpoison_range+0xf/0x30
[ 8.341217] do_init_module+0xf8/0x350
[ 8.341419] load_module+0x3fe6/0x4340
[ 8.341621] ? vm_unmap_ram+0x1d0/0x1d0
[ 8.341826] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 8.342101] ? module_frob_arch_sections+0x20/0x20
[ 8.342358] ? __do_sys_finit_module+0x108/0x170
[ 8.342604] __do_sys_finit_module+0x108/0x170
[ 8.342841] ? __ia32_sys_init_module+0x40/0x40
[ 8.343083] ? file_open_root+0x200/0x200
[ 8.343298] ? do_sys_open+0x85/0xe0
[ 8.343491] ? filp_open+0x50/0x50
[ 8.343675] ? exit_to_user_mode_prepare+0xfc/0x130
[ 8.343935] do_syscall_64+0x33/0x40
[ 8.344132] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 8.344401] RIP: 0033:0x7f08eb887cf7
[ 8.344594] Code: 48 89 57 30 48 8b 04 24 48 89 47 38 e9 1d a0 02 00 48 89 f8 48 89 f7 48 89 d6 41
[ 8.345565] RSP: 002b:00007ffcd5c98ad8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 8.345962] RAX: ffffffffffffffda RBX: 00000000008fea70 RCX: 00007f08eb887cf7
[ 8.346336] RDX: 0000000000000000 RSI: 00000000008fd9e0 RDI: 0000000000000003
[ 8.346711] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000001
[ 8.347085] R10: 00007f08eb8eb300 R11: 0000000000000246 R12: 00000000008fd9e0
[ 8.347460] R13: 0000000000000000 R14: 00000000008fddd0 R15: 0000000000000001
[ 8.347836] Modules linked in: lanai(+) atm
[ 8.348065] CR2: ffffc90000180024
[ 8.348244] ---[ end trace 7fdc1c668f2003e5 ]---
[ 8.348490] RIP: 0010:lanai_dev_close+0x4f/0xe5 [lanai]
[ 8.348772] Code: 00 48 c7 c7 00 d3 01 c0 e8 49 4e 0a c2 48 8d bd 08 02 00 00 e8 6e 52 14 c1 48 80
[ 8.349745] RSP: 0018:ffff8881029ef680 EFLAGS: 00010246
[ 8.350022] RAX: 000000000003fffe RBX: ffff888102fb4800 RCX: ffffffffc001a98a
[ 8.350397] RDX: ffffc90000180000 RSI: 0000000000000246 RDI: ffff888102fb4000
[ 8.350772] RBP: ffff888102fb4000 R08: ffffffff8115da8a R09: ffffed102053deaa
[ 8.351151] R10: 0000000000000003 R11: ffffed102053dea9 R12: ffff888102fb48a4
[ 8.351525] R13: ffffffffc00123c0 R14: ffff888102fb4b90 R15: ffff888102fb4b88
[ 8.351918] FS: 00007f08eb9056a0(0000) GS:ffff88815b400000(0000) knlGS:0000000000000000
[ 8.352343] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8.352647] CR2: ffffc90000180024 CR3: 0000000102a28000 CR4: 00000000000006f0
[ 8.353022] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8.353397] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8.353958] modprobe (95) used greatest stack depth: 26216 bytes left
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
label err_eni_release is reachable when eni_start() fail.
In eni_start() it calls dev->phy->start() in the last step, if start()
fail we don't need to call phy->stop(), if start() is never called, we
neither need to call phy->stop(), otherwise null-ptr-deref will happen.
In order to fix this issue, don't call phy->stop() in label err_eni_release
[ 4.875714] ==================================================================
[ 4.876091] BUG: KASAN: null-ptr-deref in suni_stop+0x47/0x100 [suni]
[ 4.876433] Read of size 8 at addr 0000000000000030 by task modprobe/95
[ 4.876778]
[ 4.876862] CPU: 0 PID: 95 Comm: modprobe Not tainted 5.11.0-rc7-00090-gdcc0b49040c7 #2
[ 4.877290] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd94
[ 4.877876] Call Trace:
[ 4.878009] dump_stack+0x7d/0xa3
[ 4.878191] kasan_report.cold+0x10c/0x10e
[ 4.878410] ? __slab_free+0x2f0/0x340
[ 4.878612] ? suni_stop+0x47/0x100 [suni]
[ 4.878832] suni_stop+0x47/0x100 [suni]
[ 4.879043] eni_do_release+0x3b/0x70 [eni]
[ 4.879269] eni_init_one.cold+0x1152/0x1747 [eni]
[ 4.879528] ? _raw_spin_lock_irqsave+0x7b/0xd0
[ 4.879768] ? eni_ioctl+0x270/0x270 [eni]
[ 4.879990] ? __mutex_lock_slowpath+0x10/0x10
[ 4.880226] ? eni_ioctl+0x270/0x270 [eni]
[ 4.880448] local_pci_probe+0x6f/0xb0
[ 4.880650] pci_device_probe+0x171/0x240
[ 4.880864] ? pci_device_remove+0xe0/0xe0
[ 4.881086] ? kernfs_create_link+0xb6/0x110
[ 4.881315] ? sysfs_do_create_link_sd.isra.0+0x76/0xe0
[ 4.881594] really_probe+0x161/0x420
[ 4.881791] driver_probe_device+0x6d/0xd0
[ 4.882010] device_driver_attach+0x82/0x90
[ 4.882233] ? device_driver_attach+0x90/0x90
[ 4.882465] __driver_attach+0x60/0x100
[ 4.882671] ? device_driver_attach+0x90/0x90
[ 4.882903] bus_for_each_dev+0xe1/0x140
[ 4.883114] ? subsys_dev_iter_exit+0x10/0x10
[ 4.883346] ? klist_node_init+0x61/0x80
[ 4.883557] bus_add_driver+0x254/0x2a0
[ 4.883764] driver_register+0xd3/0x150
[ 4.883971] ? 0xffffffffc0038000
[ 4.884149] do_one_initcall+0x84/0x250
[ 4.884355] ? trace_event_raw_event_initcall_finish+0x150/0x150
[ 4.884674] ? unpoison_range+0xf/0x30
[ 4.884875] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 4.885150] ? unpoison_range+0xf/0x30
[ 4.885352] ? unpoison_range+0xf/0x30
[ 4.885557] do_init_module+0xf8/0x350
[ 4.885760] load_module+0x3fe6/0x4340
[ 4.885960] ? vm_unmap_ram+0x1d0/0x1d0
[ 4.886166] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 4.886441] ? module_frob_arch_sections+0x20/0x20
[ 4.886697] ? __do_sys_finit_module+0x108/0x170
[ 4.886941] __do_sys_finit_module+0x108/0x170
[ 4.887178] ? __ia32_sys_init_module+0x40/0x40
[ 4.887419] ? file_open_root+0x200/0x200
[ 4.887634] ? do_sys_open+0x85/0xe0
[ 4.887826] ? filp_open+0x50/0x50
[ 4.888009] ? fpregs_assert_state_consistent+0x4d/0x60
[ 4.888287] ? exit_to_user_mode_prepare+0x2f/0x130
[ 4.888547] do_syscall_64+0x33/0x40
[ 4.888739] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 4.889010] RIP: 0033:0x7ff62fcf1cf7
[ 4.889202] Code: 48 89 57 30 48 8b 04 24 48 89 47 38 e9 1d a0 02 00 48 89 f8 48 89 f71
[ 4.890172] RSP: 002b:00007ffe6644ade8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 4.890570] RAX: ffffffffffffffda RBX: 0000000000f2ca70 RCX: 00007ff62fcf1cf7
[ 4.890944] RDX: 0000000000000000 RSI: 0000000000f2b9e0 RDI: 0000000000000003
[ 4.891318] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000001
[ 4.891691] R10: 00007ff62fd55300 R11: 0000000000000246 R12: 0000000000f2b9e0
[ 4.892064] R13: 0000000000000000 R14: 0000000000f2bdd0 R15: 0000000000000001
[ 4.892439] ==================================================================
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846eab ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were a few remaining tunnel drivers that didn't receive the prior
conversion to icmp{,v6}_ndo_send. Knowing now that this could lead to
memory corrution (see ee576c47db60 ("net: icmp: pass zeroed opts from
icmp{,v6}_ndo_send before sending") for details), there's even more
imperative to have these all converted. So this commit goes through the
remaining cases that I could find and does a boring translation to the
ndo variety.
The Fixes: line below is the merge that originally added icmp{,v6}_
ndo_send and converted the first batch of icmp{,v6}_send users. The
rationale then for the change applies equally to this patch. It's just
that these drivers were left out of the initial conversion because these
network devices are hiding in net/ rather than in drivers/net/.
Cc: Florian Westphal <fw@strlen.de>
Cc: Willem de Bruijn <willemb@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 803381f9f117 ("Merge branch 'icmp-account-for-NAT-when-sending-icmps-from-ndo-layer'")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 86dd9868b878 has several issues, but was accepted too soon
before anyone could take a look.
- Double free. dsa_slave_xmit() will free the skb if the xmit function
returns NULL, but the skb is already freed by eth_skb_pad(). Use
__skb_put_padto() to avoid that.
- Unnecessary allocation. It has been done by DSA core since commit
a3b0b6479700.
- A u16 pointer points to skb data. It should be __be16 for network
byte order.
- Typo in comments. "numer" -> "number".
Fixes: 86dd9868b878 ("net: dsa: tag_rtl4_a: Support also egress tags")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
shinfo already holds the result of skb_shinfo(skb) at this point - no
need to re-invoke the construct even twice.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous implementation of .handle_interrupt() did not take into
account the fact that all the interrupt status registers should be
acknowledged since multiple interrupt sources could be asserted.
Fix this by reading all the status registers before exiting with
IRQ_NONE or triggering the PHY state machine.
Fixes: 1d1ae3c6ca3f ("net: phy: ti: implement generic .handle_interrupt() callback")
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210226153020.867852-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull kmap conversion updates from David Sterba:
"This contains changes regarding kmap API use and eg conversion from
kmap_atomic to kmap_local_page.
The API belongs to memory management but to save cross-tree
dependency headaches we've agreed to take it through the btrfs tree
because there are some trivial conversions possible, while the rest
will need some time and getting the easy cases out of the way would be
convenient.
The changes can be grouped:
- function exports, new helpers
- new VM_BUG_ON for additional verification; it's been discussed if
it should be VM_BUG_ON or BUG_ON, the former was chosen due to
performance reasons
- code replaced by relevant helpers"
[ This is an updated version of a request that originally came in during
the merge window, but I asked for some updates:
https://lore.kernel.org/lkml/cover.1614090658.git.dsterba@suse.com/
which is why this got merge after the merge window closed. - Linus ]
* 'kmap-conversion-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: use copy_highpage() instead of 2 kmaps()
btrfs: use memcpy_[to|from]_page() and kmap_local_page()
mm/highmem: Add VM_BUG_ON() to mem*_page() calls
mm/highmem: Introduce memcpy_page(), memmove_page(), and memset_page()
mm/highmem: Convert memcpy_[to|from]_page() to kmap_local_page()
mm/highmem: Lift memcpy_[to|from]_page to core
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"This is the first batch of fixes that usually arrive during the merge
window code freeze. Regressions and stable material.
Regressions:
- fix deadlock in log sync in zoned mode
- fix bugs in subpage mode still wrongly assuming sectorsize == page
size
Fixes:
- fix missing kunmap of the Q stripe in RAID6
- block group fixes:
- fix race between extent freeing/allocation when using bitmaps
- avoid double put of block group when emptying cluster
- swapfile fixes:
- fix swapfile writes vs running scrub
- fix swapfile activation vs snapshot creation
- fix stale data exposure after cloning a hole with NO_HOLES enabled
- remove tree-checker check that does not work in case information
from other leaves is necessary"
* tag 'for-5.12-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix deadlock on log sync
btrfs: avoid double put of block group when emptying cluster
btrfs: fix stale data exposure after cloning a hole with NO_HOLES enabled
btrfs: tree-checker: do not error out if extent ref hash doesn't match
btrfs: fix race between swap file activation and snapshot creation
btrfs: fix race between writes to swap files and scrub
btrfs: avoid checking for RO block group twice during nocow writeback
btrfs: fix race between extent freeing/allocation when using bitmaps
btrfs: make check_compressed_csum() to be subpage compatible
btrfs: make btrfs_submit_compressed_read() subpage compatible
btrfs: fix raid6 qstripe kmap
|
|
Set err to -ENOMEM if kzalloc fails instead of 0.
Fixes: 759738537142 ("IB/mlx5: Enable subscription for device events over DEVX")
Link: https://lore.kernel.org/r/20210222122343.19720-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
When RDMA_RXE is enabled and CRYPTO is disabled, Kbuild gives the
following warning:
WARNING: unmet direct dependencies detected for CRYPTO_CRC32
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- RDMA_RXE [=y] && (INFINIBAND_USER_ACCESS [=y] || !INFINIBAND_USER_ACCESS [=y]) && INET [=y] && PCI [=y] && INFINIBAND [=y] && INFINIBAND_VIRT_DMA [=y]
This is because RDMA_RXE selects CRYPTO_CRC32, without depending on or
selecting CRYPTO, despite that config option being subordinate to CRYPTO.
Fixes: cee2688e3cd6 ("IB/rxe: Offload CRC calculation when possible")
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://lore.kernel.org/r/21525878.NYvzQUHefP@ubuntu-mate-laptop
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
ib_send_cm_sidr_rep() {
spin_lock_irqsave()
cm_send_sidr_rep_locked() {
...
spin_lock_irq()
....
spin_unlock_irq() <--- this will enable interrupts
}
spin_unlock_irqrestore()
}
spin_unlock_irqrestore() expects interrupts to be disabled but the
internal spin_unlock_irq() will always enable hard interrupts.
Fix this by replacing the internal spin_{lock,unlock}_irq() with
irqsave/restore variants.
It fixes the following kernel trace:
raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 2 PID: 20001 at kernel/locking/irqflag-debug.c:10 warn_bogus_irq_restore+0x1d/0x20
Call Trace:
_raw_spin_unlock_irqrestore+0x4e/0x50
ib_send_cm_sidr_rep+0x3a/0x50 [ib_cm]
cma_send_sidr_rep+0xa1/0x160 [rdma_cm]
rdma_accept+0x25e/0x350 [rdma_cm]
ucma_accept+0x132/0x1cc [rdma_ucm]
ucma_write+0xbf/0x140 [rdma_ucm]
vfs_write+0xc1/0x340
ksys_write+0xb3/0xe0
do_syscall_64+0x2d/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 87c4c774cbef ("RDMA/cm: Protect access to remote_sidr_table")
Link: https://lore.kernel.org/r/20210301081844.445823-1-leon@kernel.org
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
A couple of media schemas got applied without using or incorrectly
using the video-interfaces.yaml and graph.yaml schemas. Fix them up
before we have more copy-n-paste errors.
Fixes: 41b3e23376e9 ("media: dt-bindings: media: Add bindings for imx334")
Fixes: d899e5f1db7a ("media: dt-bindings: media: imx258: add bindings for IMX258 sensor")
Fixes: 918b866edfec ("media: dt-bindings: Remove old ov5647.yaml file, update ovti,ov5647.yaml")
Fixes: 22f2b47517a6 ("media: dt-bindings: media: i2c: Add OV8865 bindings documentation")
Fixes: 29a202fa7acc ("media: dt-bindings: media: i2c: Add OV5648 bindings documentation")
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: "Paul J. Murphy" <paul.j.murphy@intel.com>
Cc: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210223210127.55455-1-robh@kernel.org
|
|
We need to have our worker count updated before continuing, to avoid
cases where we repeatedly think we need a new worker, but a fork is
already in progress.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit a1ce35fa49852db60fc6e268038530be533c5b15 ("block: remove dead
elevator code") removed all users of RQF_SORTED. However it is still
defined, and there is one reference left to it (which in effect is
dead code). Clear it all up.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The DTPM framework will evolve in the next cycles. Let's add a
temporary EXPERIMENTAL tag to the option so users will be aware
the API may change over time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The root node is not set to NULL when the dtpm root node is
removed. Consequently, it is not possible to create a new root
as it is already set.
Set the root node to NULL when the last node is removed.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Because the PM-runtime status of the device is not updated in
__rpm_callback(), attempts to suspend the suppliers of the given
device triggered by rpm_put_suppliers() called by it may fail.
Fix this by making __rpm_callback() update the device's status to
RPM_SUSPENDED before calling rpm_put_suppliers() if the current
status of the device is RPM_SUSPENDING and the callback just invoked
by it has returned 0 (success).
While at it, modify the code in __rpm_callback() to always check
the device's PM-runtime status under its PM lock.
Link: https://lore.kernel.org/linux-pm/CAPDyKFqm06KDw_p8WXsM4dijDbho4bb6T4k50UqqvR1_COsp8g@mail.gmail.com/
Fixes: 21d5c57b3726 ("PM / runtime: Use device links")
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Diagnosed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Elaine Zhang <zhangiqng@rock-chips.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
set samplerate
This commit only contains the fix about the `URB_CONTROL` request
direction to set the samplerate of Pioneer DJM devices (`URB_CONTROL out`).
Fixes: 3b85f5fc75d5 ("ALSA: usb-audio: Add DJM450 to Pioneer format quirk")
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301142927.14552-1-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
entering Normal Mode
This patch prevents a potentially destructive race condition. The
device is fully operational on the bus after entering Normal Mode, so
zeroing the MRAM after entering this mode may lead to loss of
information, e.g. new received messages.
This patch fixes the problem by first initializing the MRAM, then
bringing the device into Normale Mode.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Link: https://lore.kernel.org/r/20210226163440.313628-1-torin@maxiluxsystems.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
setting skb ownership
There are two ref count variables controlling the free()ing of a socket:
- struct sock::sk_refcnt - which is changed by sock_hold()/sock_put()
- struct sock::sk_wmem_alloc - which accounts the memory allocated by
the skbs in the send path.
In case there are still TX skbs on the fly and the socket() is closed,
the struct sock::sk_refcnt reaches 0. In the TX-path the CAN stack
clones an "echo" skb, calls sock_hold() on the original socket and
references it. This produces the following back trace:
| WARNING: CPU: 0 PID: 280 at lib/refcount.c:25 refcount_warn_saturate+0x114/0x134
| refcount_t: addition on 0; use-after-free.
| Modules linked in: coda_vpu(E) v4l2_jpeg(E) videobuf2_vmalloc(E) imx_vdoa(E)
| CPU: 0 PID: 280 Comm: test_can.sh Tainted: G E 5.11.0-04577-gf8ff6603c617 #203
| Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
| Backtrace:
| [<80bafea4>] (dump_backtrace) from [<80bb0280>] (show_stack+0x20/0x24) r7:00000000 r6:600f0113 r5:00000000 r4:81441220
| [<80bb0260>] (show_stack) from [<80bb593c>] (dump_stack+0xa0/0xc8)
| [<80bb589c>] (dump_stack) from [<8012b268>] (__warn+0xd4/0x114) r9:00000019 r8:80f4a8c2 r7:83e4150c r6:00000000 r5:00000009 r4:80528f90
| [<8012b194>] (__warn) from [<80bb09c4>] (warn_slowpath_fmt+0x88/0xc8) r9:83f26400 r8:80f4a8d1 r7:00000009 r6:80528f90 r5:00000019 r4:80f4a8c2
| [<80bb0940>] (warn_slowpath_fmt) from [<80528f90>] (refcount_warn_saturate+0x114/0x134) r8:00000000 r7:00000000 r6:82b44000 r5:834e5600 r4:83f4d540
| [<80528e7c>] (refcount_warn_saturate) from [<8079a4c8>] (__refcount_add.constprop.0+0x4c/0x50)
| [<8079a47c>] (__refcount_add.constprop.0) from [<8079a57c>] (can_put_echo_skb+0xb0/0x13c)
| [<8079a4cc>] (can_put_echo_skb) from [<8079ba98>] (flexcan_start_xmit+0x1c4/0x230) r9:00000010 r8:83f48610 r7:0fdc0000 r6:0c080000 r5:82b44000 r4:834e5600
| [<8079b8d4>] (flexcan_start_xmit) from [<80969078>] (netdev_start_xmit+0x44/0x70) r9:814c0ba0 r8:80c8790c r7:00000000 r6:834e5600 r5:82b44000 r4:82ab1f00
| [<80969034>] (netdev_start_xmit) from [<809725a4>] (dev_hard_start_xmit+0x19c/0x318) r9:814c0ba0 r8:00000000 r7:82ab1f00 r6:82b44000 r5:00000000 r4:834e5600
| [<80972408>] (dev_hard_start_xmit) from [<809c6584>] (sch_direct_xmit+0xcc/0x264) r10:834e5600 r9:00000000 r8:00000000 r7:82b44000 r6:82ab1f00 r5:834e5600 r4:83f27400
| [<809c64b8>] (sch_direct_xmit) from [<809c6c0c>] (__qdisc_run+0x4f0/0x534)
To fix this problem, only set skb ownership to sockets which have still
a ref count > 0.
Fixes: 0ae89beb283a ("can: add destructor for self generated skbs")
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Andre Naujoks <nautsch2@gmail.com>
Link: https://lore.kernel.org/r/20210226092456.27126-1-o.rempel@pengutronix.de
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In the following 4 patches
| 99842c9685ab can: dev: can_rx_offload_get_echo_skb(): extend to return can frame length
| 9420e1d495e2 can: dev: can_get_echo_skb(): extend to return can frame length
| 1dcb6e57db83 can: dev: can_put_echo_skb(): extend to handle frame_len
| f0ef72febc9a can: dev: extend struct can_skb_priv to hold CAN frame length
the CAN echo SKB support was extended to hold the CAN frame
length (which is the length of the CAN frame on the wire). It is meant
as a helper for BQL support, to avoid the re-calculation of the frame
length before sending it and on TX-completion.
However if the CAN frame is send without the request to be looped back
the SKB is discarded in can_put_echo_skb() and the subsequent
can_get_echo_skb() and can_rx_offload_get_echo_skb() return 0 for the
CAN frame length. This results in BQL stalling the TX queue after a
few packages.
Until the BQL helpers can_get_echo_skb() and
can_rx_offload_get_echo_skb() are fixed, revert the BQL support for
the mcp251xfd driver.
This reverts commit 4162e18e949ba520d5116ac0323500355479a00e.
Fixes: 4162e18e949b ("can: mcp251xfd: add BQL support")
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20210228083347.28580-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Invoke flexcan_chip_freeze() to enter freeze mode, since need poll
freeze mode acknowledge.
Fixes: e955cead03117 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20210218110037.16591-4-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
RX FIFO enable failed could happen when do system reboot stress test:
[ 0.303958] flexcan 5a8d0000.can: 5a8d0000.can supply xceiver not found, using dummy regulator
[ 0.304281] flexcan 5a8d0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.314640] flexcan 5a8d0000.can: registering netdev failed
[ 0.320728] flexcan 5a8e0000.can: 5a8e0000.can supply xceiver not found, using dummy regulator
[ 0.320991] flexcan 5a8e0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.331360] flexcan 5a8e0000.can: registering netdev failed
[ 0.337444] flexcan 5a8f0000.can: 5a8f0000.can supply xceiver not found, using dummy regulator
[ 0.337716] flexcan 5a8f0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.348117] flexcan 5a8f0000.can: registering netdev failed
RX FIFO should be enabled after the FRZ/HALT are valid. But the current
code enable RX FIFO and FRZ/HALT at the same time.
Fixes: e955cead03117 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20210218110037.16591-3-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Assert HALT bit to enter freeze mode, there is a premise that FRZ bit is
asserted. This patch asserts FRZ bit in flexcan_chip_freeze, although
the reset value is 1b'1. This is a prepare patch, later patch will
invoke flexcan_chip_freeze() to enter freeze mode, which polling freeze
mode acknowledge.
Fixes: b1aa1c7a2165b ("can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze")
Link: https://lore.kernel.org/r/20210218110037.16591-2-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The Corsair Virtuoso SE RGB Wireless is a USB headset with a mic and a
sidetone feature. Assign the Corsair Virtuoso name map to the SE product
ids as well, in order to label its mixer appropriately and allow
userspace to pick the correct volume controls.
Signed-off-by: Andrea Fagiani <andfagiani@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/40bbdf55-f854-e2ee-87b4-183e6451352c@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With the removal of the skd driver, using IRQ safe locking of a bdev
bd_size_lock spinlock to protect the bdev inode size is not necessary
anymore as there is no other known driver using this lock under an IRQ
disabled context (e.g. calling set_capacity() with IRQ disabled).
Revert commit 0fe37724f8e7 ("block: fix bd_size_lock use") which
introduced the IRQ safe change.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
As reported by kernel test robot, a randconfig with high amount of
debuging options can lead to build failure for undefined reference
to replay_soft_interrupts() on ppc32.
This is due to gcc not seeing that __prep_irq_for_enabled_exit()
always returns true on ppc32 because it doesn't inline it for
some reason.
Force inlining of __prep_irq_for_enabled_exit() to fix the build.
Fixes: 344bb20b159d ("powerpc/syscall: Make interrupt.c buildable on PPC32")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/53f3a1f719441761000c41154602bf097d4350b5.1614148356.git.christophe.leroy@csgroup.eu
|
|
On book3s/32, page protection is defined by the PP bits in the PTE
which provide the following protection depending on the access
keys defined in the matching segment register:
- PP 00 means RW with key 0 and N/A with key 1.
- PP 01 means RW with key 0 and RO with key 1.
- PP 10 means RW with both key 0 and key 1.
- PP 11 means RO with both key 0 and key 1.
Since the implementation of kernel userspace access protection,
PP bits have been set as follows:
- PP00 for pages without _PAGE_USER
- PP01 for pages with _PAGE_USER and _PAGE_RW
- PP11 for pages with _PAGE_USER and without _PAGE_RW
For kernelspace segments, kernel accesses are performed with key 0
and user accesses are performed with key 1. As PP00 is used for
non _PAGE_USER pages, user can't access kernel pages not flagged
_PAGE_USER while kernel can.
For userspace segments, both kernel and user accesses are performed
with key 0, therefore pages not flagged _PAGE_USER are still
accessible to the user.
This shouldn't be an issue, because userspace is expected to be
accessible to the user. But unlike most other architectures, powerpc
implements PROT_NONE protection by removing _PAGE_USER flag instead of
flagging the page as not valid. This means that pages in userspace
that are not flagged _PAGE_USER shall remain inaccessible.
To get the expected behaviour, just mimic other architectures in the
TLB miss handler by checking _PAGE_USER permission on userspace
accesses as if it was the _PAGE_PRESENT bit.
Note that this problem only is only for 603 cores. The 604+ have
an hash table, and hash_page() function already implement the
verification of _PAGE_USER permission on userspace pages.
Fixes: f342adca3afc ("powerpc/32s: Prepare Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: Christoph Plattner <christoph.plattner@thalesgroup.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4a0c6e3bb8f0c162457bf54d9bc6fd8d7b55129f.1612160907.git.christophe.leroy@csgroup.eu
|
|
Depending on the number of online CPUs in the original kernel, it is
likely for CPU #0 to be offline in a kdump kernel. The associated IRQs
in the affinity mappings provided by irq_create_affinity_masks() are
thus not started by irq_startup(), as per-design with managed IRQs.
This can be a problem with multi-queue block devices driven by blk-mq :
such a non-started IRQ is very likely paired with the single queue
enforced by blk-mq during kdump (see blk_mq_alloc_tag_set()). This
causes the device to remain silent and likely hangs the guest at
some point.
This is a regression caused by commit 9ea69a55b3b9 ("powerpc/pseries:
Pass MSI affinity to irq_create_mapping()"). Note that this only happens
with the XIVE interrupt controller because XICS has a workaround to bypass
affinity, which is activated during kdump with the "noirqdistrib" kernel
parameter.
The issue comes from a combination of factors:
- discrepancy between the number of queues detected by the multi-queue
block driver, that was used to create the MSI vectors, and the single
queue mode enforced later on by blk-mq because of kdump (i.e. keeping
all queues fixes the issue)
- CPU#0 offline (i.e. kdump always succeed with CPU#0)
Given that I couldn't reproduce on x86, which seems to always have CPU#0
online even during kdump, I'm not sure where this should be fixed. Hence
going for another approach : fine-grained affinity is for performance
and we don't really care about that during kdump. Simply revert to the
previous working behavior of ignoring affinity masks in this case only.
Fixes: 9ea69a55b3b9 ("powerpc/pseries: Pass MSI affinity to irq_create_mapping()")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210215094506.1196119-1-groug@kaod.org
|
|
lkp reported a build error in fsp2.o:
CC arch/powerpc/platforms/44x/fsp2.o
{standard input}:577: Error: unsupported relocation against base
Which comes from:
pr_err("GESR0: 0x%08x\n", mfdcr(base + PLB4OPB_GESR0));
Where our mfdcr() macro is stringifying "base + PLB4OPB_GESR0", and
passing that to the assembler, which obviously doesn't work.
The mfdcr() macro already checks that the argument is constant using
__builtin_constant_p(), and if not calls the out-of-line version of
mfdcr(). But in this case GCC is smart enough to notice that "base +
PLB4OPB_GESR0" will be constant, even though it's not something we can
immediately stringify into a register number.
Segher pointed out that passing the register number to the inline asm
as a constant would be better, and in fact it fixes the build error,
presumably because it gives GCC a chance to resolve the value.
While we're at it, change mtdcr() similarly.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210218123058.748882-1-mpe@ellerman.id.au
|
|
|
|
Pull ide fix from Jens Axboe:
"This is a leftover fix from 5.11, where I forgot to ship it your way"
* tag 'ide-5.11-2021-02-28' of git://git.kernel.dk/linux-block:
ide/falconide: Fix module unload
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix UNUSED_KSYMS_WHITELIST for Clang LTO
- Make -s builds really silent irrespective of V= option
- Fix build error when SUBLEVEL or PATCHLEVEL is empty
* tag 'kbuild-fixes-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Fix <linux/version.h> for empty SUBLEVEL or PATCHLEVEL again
kbuild: make -s option take precedence over V=1
ia64: remove redundant READELF from arch/ia64/Makefile
kbuild: do not include include/config/auto.conf from adjust_autoksyms.sh
kbuild: fix UNUSED_KSYMS_WHITELIST for Clang LTO
kbuild: lto: add _mcount to list of used symbols
|
|
Pull arch/csky updates from Guo Ren:
"Features:
- add new memory layout 2.5G(user):1.5G(kernel)
- add kmemleak support
- reconstruct VDSO framework: add VDSO with GENERIC_GETTIMEOFDAY,
GENERIC_TIME_VSYSCALL, HAVE_GENERIC_VDSO
- add faulthandler_disabled() check
- support (fix) swapon
- add (fix) _PAGE_ACCESSED for default pgprot
- abort uaccess retries upon fatal signal (from arm)
Fixes and optimizations:
- fix perf probe failure
- fix show_regs doesn't contain regs->usp
- remove custom asm/atomic.h implementation
- fix barrier design
- fix futex SMP implementation
- fix asm/cmpxchg.h with correct ordering barrier
- cleanup asm/spinlock.h
- fix PTE global for 2.5:1.5 virtual memory
- remove prologue of page fault handler in entry.S
- fix TLB maintenance synchronization problem
- add show_tlb for CPU_CK860 debug
- fix FAULT_FLAG_XXX param for handle_mm_fault
- fix update_mmu_cache called with user io mapping
- fix do_page_fault parent irq status
- fix a size determination in gpr_get()
- pgtable.h: Coding convention
- kprobe: Fix code in simulate without 'long'
- fix pfn_valid error with wrong max_mapnr
- use free_initmem_default() in free_initmem()
- fix compile error"
* tag 'csky-for-linus-5.12-rc1' of git://github.com/c-sky/csky-linux: (30 commits)
csky: Fixup compile error
csky: use free_initmem_default() in free_initmem()
csky: Fixup pfn_valid error with wrong max_mapnr
csky: Add VDSO with GENERIC_GETTIMEOFDAY, GENERIC_TIME_VSYSCALL, HAVE_GENERIC_VDSO
csky: kprobe: Fixup code in simulate without 'long'
csky: Fixup swapon
csky: pgtable.h: Coding convention
csky: Fixup _PAGE_ACCESSED for default pgprot
csky: remove unused including <linux/version.h>
csky: Fix a size determination in gpr_get()
csky: Reconstruct VDSO framework
csky: mm: abort uaccess retries upon fatal signal
csky: Sync riscv mm/fault.c for easy maintenance
csky: Fixup do_page_fault parent irq status
csky: Add faulthandler_disabled() check
csky: Fixup update_mmu_cache called with user io mapping
csky: Fixup FAULT_FLAG_XXX param for handle_mm_fault
csky: Add show_tlb for CPU_CK860 debug
csky: Fix TLB maintenance synchronization problem
csky: Add kmemleak support
...
|
|
Huazhong Tan says:
====================
net: hns3: fixes fot -net
The patchset includes some fixes for the HNS3 ethernet driver.
====================
Link: https://lore.kernel.org/r/1614410693-8107-1-git-send-email-tanhuazhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
