| Age | Commit message (Collapse) | Author |
|---|
|
Trivial fix to set y1 = y2 = 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We aren't using it, so no need. Save additional dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Saves lots of dwords in blit emit
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Use of HDP_*_COHERENCY_FLUSH_CNTL can cause a hang in certain
situations. Add workaround.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We used to limit the rs4xx gart aperture to 32 MB, but I suspect
that was due to not meeting the alignment requirements of the
aperture. This patch should only be applied after:
"drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics"
has been applied.
This patch should probably soak for a bit in d-r-t.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Need this to avoid conflicts with future radeon fixes
|
|
The "error" variable is unsigned so it's never less than zero. I
changed it to check if (freq < current_freq) directly.
"best_error" is also unsigned so "best_error - 100" could be a large
number instead of a negative. Since "error" is unsigned it is never
less than a negative and so the cases where "best_error" is less than or
equal to 100 are false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.
Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.
This allows kexec to work on a Power6/RN50 system.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This fixes a problem where on low VRAM cards we'd run out of space for validation.
[airlied: Tested on my M7, Thinkpad T42, compiz works with no problems.]
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is required for the NB_MISC regs on rs780/rs880 which
means HDMI/DVI/DP ports using PCIEPHY won't work without
it. It might also help with s/r (asic init) issues on other
atombios cards.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28774
and similar issues reported by Alberto Milone.
[airlied: Squash io fix patch]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We will need method of selecting encoder that should receive HDMI block. For
now we assign HDMI block to first enabled encoder. Hopefully there are not many
RS6x0 chips with two digital encoders.
[airlied: add RS740 checks as per Alex suggestion.]
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is needed to enable audio support on devices using polling. In case user
decides to disable audio (module parameter) we still will try to use timer in
r600_audio_enable_polling. This would lead to BUG in kernel/timer.c.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Userspace needs this information to access tiled
buffers via the CPU.
v2: rebased on evergreen accel changes
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Covers depth, cb, and textures. Hopefully I got this right.
v2: - fix bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=28327
https://bugs.freedesktop.org/show_bug.cgi?id=28381
- use ALIGNED(), IS_ALIGNED() macros
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Check for relocs for DB_DEPTH_INFO, CB_COLOR*_INFO, and texture
resources.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Needed for scanning out of a tiled buffer.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Needed for scanning out of a tiled buffer.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
rv6xx/rv7xx/evergreen families supported; older asics did
not have an internal thermal sensor.
Note, not all oems use the internal thermal sensor, so it's
only exposed in cases where it is used.
Note also, that most laptops use an oem specific ACPI solution for
GPU thermal information rather than using the internal thermal
sensor directly.
v2: export millidegrees celsius, use hwmon device properly.
v3: fix Kconfig
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
By calling the ATIF method in the radeon driver we can make sure
that hotkeys such as the video switch key emit ACPI events when
pressed.
agd5f: fix warning
Signed-off-by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some tables have delays that can cause the timeout to hit
even when not intended.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=27744
and related bugs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
- Make the logic in r100_pll_errata_after_index() match the other
errata functions
- Use rdev->family rather than rdev->flags & RADEON_FAMILY_MASK for kms
- replace rn50 check using ids with ASIC_IS_RN50 convenience macro
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch improves the recovery of the MPC's I2C bus from errors like bus
hangs resulting in timeouts:
1. make the bus timeout configurable, as it depends on the bus clock and
the attached slave chip(s); default is still 1 second;
2. detect any of the cases indicated by the CF, BB and RXAK MSR flags if a
timeout occurs, and add a missing (required) MAL reset;
3. use a more reliable method to fixup the bus if a hang has been detected.
The sequence is sent 9 times which seems to be necessary if a slave
"misses" more than one clock cycle. For 400 kHz bus speed, the fixup is
also ~70us (81us vs. 150us) faster.
Tested on a custom Lite5200b derived board, with a Dallas RTC, AD sensors
and NXP IO expander chips attached to the i2c.
Changes vs. v1:
- use improved bus fixup sequence for all chips (not only the 5200)
- calculate real clock from defaults if no clock is given in the device tree
- better description (I hope) of the changes.
I didn't split the changes in this file into three parts as recommended by
Grant, as they actually belong together (i.e. they address one single
problem, just in three places of one single source file).
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
[grant.likely@secretlab.ca: fixup for ->node to ->dev.of_node transition]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* Add tft display module compatibility for new
hardware modules
Signed-off-by: Adrian Alonso <aalonso00@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Adds support for encoding display mode information
in the device tree using verbatim EDID block.
If the EDID entry in the DIU node is present, the
driver will build mode database using EDID data
and allow setting the display modes from this database.
Otherwise display mode will be set using mode
entries from driver's internal database as usual.
This patch also updates device tree bindings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Update compatible and interrupt properties description.
Furthermore an example for the MPC5121 has been added.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
MPC5121 DIU configuration/setup as initialized by the boot
loader currently will get lost while booting Linux. As a
result displaying the boot splash is not possible through
the boot process.
To prevent this we reserve configured DIU frame buffer
address range while booting and preserve AOI descriptor
and gamma table so that DIU continues displaying through
the whole boot process. On first open from user space
DIU frame buffer driver releases the reserved frame
buffer area and continues to operate as usual.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Some DIU structures will be used in platform code in
subsequent MPC5121 DIU patch, so we move this header
to be able to include it elsewhere.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
On MPC5121e Rev 2.0 re-configuring the DIU area descriptor
by writing new descriptor address doesn't always work.
As a result, DIU continues to display using old area descriptor
even if the new one has been written to the descriptor register of
the plane.
Add the code from Freescale MPC5121EADS BSP for writing descriptor
addresses properly. This fixes the problem for Rev 2.0 silicon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Allows using clk_get()/clk_enable()/clk_disable() for VIU
clock in the v4l2 video driver.
Signed-off-by: Hongjun Chen <hong-jun.chen@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Adds IFM PDM360NG device tree and platform code.
Currently following is supported:
- Spansion S29GL512P 256 MB NOR flash
- ST Micro NAND 1 GiB flash
- DIU, please use "fbcon=map:5 video=fslfb:800x480-32@60"
at the kernel command line to enable PrimeView PM070WL3
Display support.
- FEC
- I2C
- RTC, EEPROM
- MSCAN
- PSC UART, please pass "console=tty0 console=ttyPSC5,115200"
on the kernel command line.
- SPI, ADS7845 Touchscreen
- USB0/1 Host
- USB0 OTG Host/Device
- VIU, Overlay/Capture support
Signed-off-by: Markus Fischer <markus.fischer.ec@ifm.com>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Allow board selection in a drop-down board sub-menu
like many other platforms do.
Before the patch:
...
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
Patched:
...
[*] 512x-based boards
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
This is a cleanup before adding new board selection entry.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
|
|
nfs_commit_inode() needs to be defined irrespectively of whether or not
we are supporting NFSv3 and NFSv4.
Allow the compiler to optimise away code in the NFSv2-only case by
converting it into an inlined stub function.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch converts unnecessary divide and modulo operations
in the KVM large page related code into logical operations.
This allows to convert gfn_t to u64 while not breaking 32
bit builds.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
This patch fixes the following warning.
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
include/linux/kvm_host.h:259 invoked rcu_dereference_check() without
protection!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
no locks held by qemu-system-x86/29679.
stack backtrace:
Pid: 29679, comm: qemu-system-x86 Not tainted 2.6.35-rc3+ #200
Call Trace:
[<ffffffff810a224e>] lockdep_rcu_dereference+0xa8/0xb1
[<ffffffffa018a06f>] kvm_iommu_unmap_memslots+0xc9/0xde [kvm]
[<ffffffffa018a0c4>] kvm_iommu_unmap_guest+0x40/0x4e [kvm]
[<ffffffffa018f772>] kvm_arch_destroy_vm+0x1a/0x186 [kvm]
[<ffffffffa01800d0>] kvm_put_kvm+0x110/0x167 [kvm]
[<ffffffffa0180ecc>] kvm_vcpu_release+0x18/0x1c [kvm]
[<ffffffff81156f5d>] fput+0x22a/0x3a0
[<ffffffff81152288>] filp_close+0xb4/0xcd
[<ffffffff8106599f>] put_files_struct+0x1b7/0x36b
[<ffffffff81065830>] ? put_files_struct+0x48/0x36b
[<ffffffff8131ee59>] ? do_raw_spin_unlock+0x118/0x160
[<ffffffff81065bc0>] exit_files+0x6d/0x75
[<ffffffff81068348>] do_exit+0x47d/0xc60
[<ffffffff8177e7b5>] ? _raw_spin_unlock_irq+0x30/0x36
[<ffffffff81068bfa>] do_group_exit+0xcf/0x134
[<ffffffff81080790>] get_signal_to_deliver+0x732/0x81d
[<ffffffff81095996>] ? cpu_clock+0x4e/0x60
[<ffffffff81002082>] do_notify_resume+0x117/0xc43
[<ffffffff810a2fa3>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff81080d79>] ? sys_rt_sigtimedwait+0x2b5/0x3bf
[<ffffffff8177d9f2>] ? trace_hardirqs_off_thunk+0x3a/0x3c
[<ffffffff81003221>] ? sysret_signal+0x5/0x3d
[<ffffffff8100343b>] int_signal+0x12/0x17
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
We just introduced generic functions to handle shadow pages on PPC.
This patch makes the respective backends make use of them, getting
rid of a lot of duplicate code along the way.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Currently the shadow paging code keeps an array of entries it knows about.
Whenever the guest invalidates an entry, we loop through that entry,
trying to invalidate matching parts.
While this is a really simple implementation, it is probably the most
ineffective one possible. So instead, let's keep an array of lists around
that are indexed by a hash. This way each PTE can be added by 4 list_add,
removed by 4 list_del invocations and the search only needs to loop through
entries that share the same hash.
This patch implements said lookup and exports generic functions that both
the 32-bit and 64-bit backend can use.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Cleanup this function that we are already get the direct sp's access
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
If the mapping is writable but the dirty flag is not set, we will find
the read-only direct sp and setup the mapping, then if the write #PF
occur, we will mark this mapping writable in the read-only direct sp,
now, other real read-only mapping will happily write it without #PF.
It may hurt guest's COW
Fixed by re-install the mapping when write #PF occur.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
In no-direct mapping, we mark sp is 'direct' when we mapping the
guest's larger page, but its access is encoded form upper page-struct
entire not include the last mapping, it will cause access conflict.
For example, have this mapping:
[W]
/ PDE1 -> |---|
P[W] | | LPA
\ PDE2 -> |---|
[R]
P have two children, PDE1 and PDE2, both PDE1 and PDE2 mapping the
same lage page(LPA). The P's access is WR, PDE1's access is WR,
PDE2's access is RO(just consider read-write permissions here)
When guest access PDE1, we will create a direct sp for LPA, the sp's
access is from P, is W, then we will mark the ptes is W in this sp.
Then, guest access PDE2, we will find LPA's shadow page, is the same as
PDE's, and mark the ptes is RO.
So, if guest access PDE1, the incorrect #PF is occured.
Fixed by encode the last mapping access into direct shadow page
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
While we sync many unsync sp at one time(in mmu_sync_children()),
we may mapping the spte writable, it's dangerous, if one unsync
sp's mapping gfn is another unsync page's gfn.
For example:
SP1.pte[0] = P
SP2.gfn's pfn = P
[SP1.pte[0] = SP2.gfn's pfn]
First, we write protected SP1 and SP2, but SP1 and SP2 are still the
unsync sp.
Then, sync SP1 first, it will detect SP1.pte[0].gfn only has one unsync-sp,
that is SP2, so it will mapping it writable, but we plan to sync SP2 soon,
at this point, the SP2->unsync is not reliable since later we sync SP2 but
SP2->gfn is already writable.
So the final result is: SP2 is the sync page but SP2.gfn is writable.
This bug will corrupt guest's page table, fixed by mark read-only mapping
if the mapped gfn has shadow pages.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Some guest device driver may leverage the "Non-Snoop" I/O, and explicitly
WBINVD or CLFLUSH to a RAM space. Since migration may occur before WBINVD or
CLFLUSH, we need to maintain data consistency either by:
1: flushing cache (wbinvd) when the guest is scheduled out if there is no
wbinvd exit, or
2: execute wbinvd on all dirty physical CPUs when guest wbinvd exits.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
No need to reload the mmu in between two different vcpu->requests checks.
kvm_mmu_reload() may trigger KVM_REQ_TRIPLE_FAULT, but that will be caught
during atomic guest entry later.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Older versions of 32-bit linux have a "Checking 'hlt' instruction"
test where they repeatedly call the 'hlt' instruction, and then
expect a timer interrupt to kick the CPU out of halt. This happens
before any LAPIC or IOAPIC setup happens, which means that all of
the APIC's are in virtual wire mode at this point. Unfortunately,
the current implementation of virtual wire mode is hardcoded to
only kick the BSP, so if a crash+kexec occurs on a different
vcpu, it will never get kicked.
This patch makes pic_unlock() do the equivalent of
kvm_irq_delivery_to_apic() for the IOAPIC code. That is, it runs
through all of the vcpus looking for one that is in virtual wire
mode. In the normal case where LAPICs and IOAPICs are configured,
this won't be used at all. In the bootstrap phase of a modern
OS, before the LAPICs and IOAPICs are configured, this will have
exactly the same behavior as today; VCPU0 is always looked at
first, so it will always get out of the loop after the first
iteration. This will only go through the loop more than once
during a kexec/kdump, in which case it will only do it a few times
until the kexec'ed kernel programs the LAPIC and IOAPIC.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
