summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-01-23bcache: avoid unnecessary btree nodes flushing in btree_flush_write()Coly Li
the commit 91be66e1318f ("bcache: performance improvement for btree_flush_write()") was an effort to flushing btree node with oldest btree node faster in following methods, - Only iterate dirty btree nodes in c->btree_cache, avoid scanning a lot of clean btree nodes. - Take c->btree_cache as a LRU-like list, aggressively flushing all dirty nodes from tail of c->btree_cache util the btree node with oldest journal entry is flushed. This is to reduce the time of holding c->bucket_lock. Guoju Fang and Shuang Li reported that they observe unexptected extra write I/Os on cache device after applying the above patch. Guoju Fang provideed more detailed diagnose information that the aggressive btree nodes flushing may cause 10x more btree nodes to flush in his workload. He points out when system memory is large enough to hold all btree nodes in memory, c->btree_cache is not a LRU-like list any more. Then the btree node with oldest journal entry is very probably not- close to the tail of c->btree_cache list. In such situation much more dirty btree nodes will be aggressively flushed before the target node is flushed. When slow SATA SSD is used as cache device, such over- aggressive flushing behavior will cause performance regression. After spending a lot of time on debug and diagnose, I find the real condition is more complicated, aggressive flushing dirty btree nodes from tail of c->btree_cache list is not a good solution. - When all btree nodes are cached in memory, c->btree_cache is not a LRU-like list, the btree nodes with oldest journal entry won't be close to the tail of the list. - There can be hundreds dirty btree nodes reference the oldest journal entry, before flushing all the nodes the oldest journal entry cannot be reclaimed. When the above two conditions mixed together, a simply flushing from tail of c->btree_cache list is really NOT a good idea. Fortunately there is still chance to make btree_flush_write() work better. Here is how this patch avoids unnecessary btree nodes flushing, - Only acquire c->journal.lock when getting oldest journal entry of fifo c->journal.pin. In rested locations check the journal entries locklessly, so their values can be changed on other cores in parallel. - In loop list_for_each_entry_safe_reverse(), checking latest front point of fifo c->journal.pin. If it is different from the original point which we get with locking c->journal.lock, it means the oldest journal entry is reclaim on other cores. At this moment, all selected dirty nodes recorded in array btree_nodes[] are all flushed and clean on other CPU cores, it is unncessary to iterate c->btree_cache any longer. Just quit the list_for_each_entry_safe_reverse() loop and the following for-loop will skip all the selected clean nodes. - Find a proper time to quit the list_for_each_entry_safe_reverse() loop. Check the refcount value of orignial fifo front point, if the value is larger than selected node number of btree_nodes[], it means more matching btree nodes should be scanned. Otherwise it means no more matching btee nodes in rest of c->btree_cache list, the loop can be quit. If the original oldest journal entry is reclaimed and fifo front point is updated, the refcount of original fifo front point will be 0, then the loop will be quit too. - Not hold c->bucket_lock too long time. c->bucket_lock is also required for space allocation for cached data, hold it for too long time will block regular I/O requests. When iterating list c->btree_cache, even there are a lot of maching btree nodes, in order to not holding c->bucket_lock for too long time, only BTREE_FLUSH_NR nodes are selected and to flush in following for-loop. With this patch, only btree nodes referencing oldest journal entry are flushed to cache device, no aggressive flushing for unnecessary btree node any more. And in order to avoid blocking regluar I/O requests, each time when btree_flush_write() called, at most only BTREE_FLUSH_NR btree nodes are selected to flush, even there are more maching btree nodes in list c->btree_cache. At last, one more thing to explain: Why it is safe to read front point of c->journal.pin without holding c->journal.lock inside the list_for_each_entry_safe_reverse() loop ? Here is my answer: When reading the front point of fifo c->journal.pin, we don't need to know the exact value of front point, we just want to check whether the value is different from the original front point (which is accurate value because we get it while c->jouranl.lock is held). For such purpose, it works as expected without holding c->journal.lock. Even the front point is changed on other CPU core and not updated to local core, and current iterating btree node has identical journal entry local as original fetched fifo front point, it is still safe. Because after holding mutex b->write_lock (with memory barrier) this btree node can be found as clean and skipped, the loop will quite latter when iterate on next node of list c->btree_cache. Fixes: 91be66e1318f ("bcache: performance improvement for btree_flush_write()") Reported-by: Guoju Fang <fangguoju@gmail.com> Reported-by: Shuang Li <psymon@bonuscloud.io> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: add code comments for state->pool in __btree_sort()Coly Li
To explain the pages allocated from mempool state->pool can be swapped in __btree_sort(), because state->pool is a page pool, which allocates pages by alloc_pages() indeed. Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23lib: crc64: include <linux/crc64.h> for 'crc64_be'Ben Dooks (Codethink)
The crc64_be() is declared in <linux/crc64.h> so include this where the symbol is defined to avoid the following warning: lib/crc64.c:43:12: warning: symbol 'crc64_be' was not declared. Should it be static? Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: use read_cache_page_gfp to read the superblockChristoph Hellwig
Avoid a pointless dependency on buffer heads in bcache by simply open coding reading a single page. Also add a SB_OFFSET define for the byte offset of the superblock instead of using magic numbers. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: store a pointer to the on-disk sb in the cache and cached_dev structuresChristoph Hellwig
This allows to properly build the superblock bio including the offset in the page using the normal bio helpers. This fixes writing the superblock for page sizes larger than 4k where the sb write bio would need an offset in the bio_vec. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: return a pointer to the on-disk sb from read_superChristoph Hellwig
Returning the properly typed actual data structure insteaf of the containing struct page will save the callers some work going forward. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: transfer the sb_page reference to register_{bdev,cache}Christoph Hellwig
Avoid an extra reference count roundtrip by transferring the sb_page ownership to the lower level register helpers. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: fix use-after-free in register_bcache()Coly Li
The patch "bcache: rework error unwinding in register_bcache" introduces a use-after-free regression in register_bcache(). Here are current code, 2510 out_free_path: 2511 kfree(path); 2512 out_module_put: 2513 module_put(THIS_MODULE); 2514 out: 2515 pr_info("error %s: %s", path, err); 2516 return ret; If some error happens and the above code path is executed, at line 2511 path is released, but referenced at line 2515. Then KASAN reports a use- after-free error message. This patch changes line 2515 in the following way to fix the problem, 2515 pr_info("error %s: %s", path?path:"", err); Signed-off-by: Coly Li <colyli@suse.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: properly initialize 'path' and 'err' in register_bcache()Coly Li
Patch "bcache: rework error unwinding in register_bcache" from Christoph Hellwig changes the local variables 'path' and 'err' in undefined initial state. If the code in register_bcache() jumps to label 'out:' or 'out_module_put:' by goto, these two variables might be reference with undefined value by the following line, out_module_put: module_put(THIS_MODULE); out: pr_info("error %s: %s", path, err); return ret; Therefore this patch initializes these two local variables properly in register_bcache() to avoid such issue. Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: rework error unwinding in register_bcacheChristoph Hellwig
Split the successful and error return path, and use one goto label for each resource to unwind. This also fixes some small errors like leaking the module reference count in the reboot case (which seems entirely harmless) or printing the wrong warning messages for early failures. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: use a separate data structure for the on-disk super blockChristoph Hellwig
Split out an on-disk version struct cache_sb with the proper endianness annotations. This fixes a fair chunk of sparse warnings, but there are some left due to the way the checksum is defined. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23bcache: cached_dev_free needs to put the sb pageLiang Chen
Same as cache device, the buffer page needs to be put while freeing cached_dev. Otherwise a page would be leaked every time a cached_dev is stopped. Signed-off-by: Liang Chen <liangchen.linux@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-23readdir: make user_access_begin() use the real access rangeLinus Torvalds
In commit 9f79b78ef744 ("Convert filldir[64]() from __put_user() to unsafe_put_user()") I changed filldir to not do individual __put_user() accesses, but instead use unsafe_put_user() surrounded by the proper user_access_begin/end() pair. That make them enormously faster on modern x86, where the STAC/CLAC games make individual user accesses fairly heavy-weight. However, the user_access_begin() range was not really the exact right one, since filldir() has the unfortunate problem that it needs to not only fill out the new directory entry, it also needs to fix up the previous one to contain the proper file offset. It's unfortunate, but the "d_off" field in "struct dirent" is _not_ the file offset of the directory entry itself - it's the offset of the next one. So we end up backfilling the offset in the previous entry as we walk along. But since x86 didn't really care about the exact range, and used to be the only architecture that did anything fancy in user_access_begin() to begin with, the filldir[64]() changes did something lazy, and even commented on it: /* * Note! This range-checks 'previous' (which may be NULL). * The real range was checked in getdents */ if (!user_access_begin(dirent, sizeof(*dirent))) goto efault; and it all worked fine. But now 32-bit ppc is starting to also implement user_access_begin(), and the fact that we faked the range to only be the (possibly not even valid) previous directory entry becomes a problem, because ppc32 will actually be using the range that is passed in for more than just "check that it's user space". This is a complete rewrite of Christophe's original patch. By saving off the record length of the previous entry instead of a pointer to it in the filldir data structures, we can simplify the range check and the writing of the previous entry d_off field. No need for any conditionals in the user accesses themselves, although we retain the conditional EINTR checking for the "was this the first directory entry" signal handling latency logic. Fixes: 9f79b78ef744 ("Convert filldir[64]() from __put_user() to unsafe_put_user()") Link: https://lore.kernel.org/lkml/a02d3426f93f7eb04960a4d9140902d278cab0bb.1579697910.git.christophe.leroy@c-s.fr/ Link: https://lore.kernel.org/lkml/408c90c4068b00ea8f1c41cca45b84ec23d4946b.1579783936.git.christophe.leroy@c-s.fr/ Reported-and-tested-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-01-23readdir: be more conservative with directory entry namesLinus Torvalds
Commit 8a23eb804ca4 ("Make filldir[64]() verify the directory entry filename is valid") added some minimal validity checks on the directory entries passed to filldir[64](). But they really were pretty minimal. This fleshes out at least the name length check: we used to disallow zero-length names, but really, negative lengths or oevr-long names aren't ok either. Both could happen if there is some filesystem corruption going on. Now, most filesystems tend to use just an "unsigned char" or similar for the length of a directory entry name, so even with a corrupt filesystem you should never see anything odd like that. But since we then use the name length to create the directory entry record length, let's make sure it actually is half-way sensible. Note how POSIX states that the size of a path component is limited by NAME_MAX, but we actually use PATH_MAX for the check here. That's because while NAME_MAX is generally the correct maximum name length (it's 255, for the same old "name length is usually just a byte on disk"), there's nothing in the VFS layer that really cares. So the real limitation at a VFS layer is the total pathname length you can pass as a filename: PATH_MAX. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-01-23drm/amdgpu: remove the experimental flag for renoirAlex Deucher
Should work properly with the latest sbios on 5.5 and newer kernels. Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-23ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1Raag Jadav
Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux. Signed-off-by: Raag Jadav <raagjadav@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2020-01-23Merge back new material related to system-wide PM for v5.6.Rafael J. Wysocki
2020-01-23fou: Fix IPv6 netlink policyKristian Evensen
When submitting v2 of "fou: Support binding FoU socket" (1713cb37bf67), I accidentally sent the wrong version of the patch and one fix was missing. In the initial version of the patch, as well as the version 2 that I submitted, I incorrectly used ".type" for the two V6-attributes. The correct is to use ".len". Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: 1713cb37bf67 ("fou: Support binding FoU socket") Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23Merge tag 'wireless-drivers-2020-01-23' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.5 Second set of fixes for v5.5. There are quite a few patches, especially on iwlwifi, due to me being on a long break. Libertas also has a security fix and mt76 a build fix. iwlwifi * don't send the PPAG command when PPAG is disabled, since it can cause problems * a few fixes for a HW bug * a fix for RS offload; * a fix for 3168 devices where the NVM tables where the wrong tables were being read * fix a couple of potential memory leaks in TXQ code * disable L0S states in all hardware since our hardware doesn't officially support them anymore (and older versions of the hardware had instability in these states) * remove lar_disable parameter since it has been causing issues for some people who erroneously disable it * force the debug monitor HW to stop also when debug is disabled, since it sometimes stays on and prevents low system power states * don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems libertas * fix two buffer overflows mt76 * build fix related to CONFIG_MT76_LEDS * fix off by one in bitrates handling ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23Merge branch 'spi-5.6' into spi-nextMark Brown
2020-01-23Merge branch 'spi-5.5' into spi-linusMark Brown
2020-01-23Merge remote-tracking branch 'regulator/topic/equal' into regulator-nextMark Brown
2020-01-23Merge branch 'regulator-5.6' into regulator-nextMark Brown
2020-01-23Merge branch 'regulator-5.5' into regulator-linusMark Brown
2020-01-23dt-binding: spi: add NPCM PSPI reset bindingTomer Maimon
Add NPCM Peripheral SPI reset binding documentation, Removing unnecessary aliases use. Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200115162301.235926-4-tmaimon77@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-01-23dmaengine: ti: k3-udma: fix spelling mistake "limted" -> "limited"Colin Ian King
There are spelling mistakes in dev_err messages. Fix them. Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20200122093818.2800743-1-colin.king@canonical.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-23dmaengine: s3c24xx-dma: fix spelling mistake "to" -> "too"Colin Ian King
There is a spelling mistake in a dev_err message. Fix it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20200122235237.2830344-1-colin.king@canonical.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-23tun: add mutex_unlock() call and napi.skb clearing in tun_get_user()Eric Dumazet
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program consumes the skb, we need to clear the napi.skb (or risk a use-after-free) and release the mutex (or risk a deadlock) WARNING: lock held when returning to user space! 5.5.0-rc6-syzkaller #0 Not tainted ------------------------------------------------ syz-executor.0/455 is leaving the kernel with locks still held! 1 lock held by syz-executor.0/455: #0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835 Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Petar Penkov <ppenkov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23mlxsw: spectrum_acl: Fix use-after-free during reloadIdo Schimmel
During reload (or module unload), the router block is de-initialized. Among other things, this results in the removal of a default multicast route from each active virtual router (VRF). These default routes are configured during initialization to trap packets to the CPU. In Spectrum-2, unlike Spectrum-1, multicast routes are implemented using ACL rules. Since the router block is de-initialized before the ACL block, it is possible that the ACL rules corresponding to the default routes are deleted while being accessed by the ACL delayed work that queries rules' activity from the device. This can result in a rare use-after-free [1]. Fix this by protecting the rules list accessed by the delayed work with a lock. We cannot use a spinlock as the activity read operation is blocking. [1] [ 123.331662] ================================================================== [ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0 [ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78 [ 123.357080] [ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209 [ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 [ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work [ 123.385970] Call Trace: [ 123.388734] dump_stack+0xc6/0x11e [ 123.392568] print_address_description.constprop.4+0x21/0x340 [ 123.403236] __kasan_report.cold.8+0x76/0xb1 [ 123.414884] kasan_report+0xe/0x20 [ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0 [ 123.444034] process_one_work+0xb06/0x19a0 [ 123.453731] worker_thread+0x91/0xe90 [ 123.467348] kthread+0x348/0x410 [ 123.476847] ret_from_fork+0x24/0x30 [ 123.480863] [ 123.482545] Allocated by task 73: [ 123.486273] save_stack+0x19/0x80 [ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0 [ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230 [ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0 [ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820 [ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690 [ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0 [ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990 [ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60 [ 123.532752] process_one_work+0xb06/0x19a0 [ 123.537352] worker_thread+0x91/0xe90 [ 123.541471] kthread+0x348/0x410 [ 123.545103] ret_from_fork+0x24/0x30 [ 123.549113] [ 123.550795] Freed by task 518: [ 123.554231] save_stack+0x19/0x80 [ 123.557958] __kasan_slab_free+0x125/0x170 [ 123.562556] kfree+0xd7/0x3a0 [ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0 [ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130 [ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260 [ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290 [ 123.588091] mlxsw_sp_vr_put+0x1db/0x350 [ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0 [ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360 [ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470 [ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120 [ 123.612260] mlxsw_sp_router_fini+0x137/0x384 [ 123.617152] mlxsw_sp_fini+0x30a/0x4a0 [ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600 [ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0 [ 123.634176] devlink_reload+0xb4/0x380 [ 123.638391] devlink_nl_cmd_reload+0x610/0x700 [ 123.643382] genl_rcv_msg+0x6a8/0xdc0 [ 123.647497] netlink_rcv_skb+0x134/0x3a0 [ 123.651904] genl_rcv+0x29/0x40 [ 123.655436] netlink_unicast+0x4d4/0x700 [ 123.659843] netlink_sendmsg+0x7c0/0xc70 [ 123.664251] __sys_sendto+0x265/0x3c0 [ 123.668367] __x64_sys_sendto+0xe2/0x1b0 [ 123.672773] do_syscall_64+0xa0/0x530 [ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 123.682552] [ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500 [ 123.684238] which belongs to the cache kmalloc-128 of size 128 [ 123.698261] The buggy address is located 32 bytes inside of [ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580) [ 123.711303] The buggy address belongs to the page: [ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0 [ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500 [ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 [ 123.743315] page dumped because: kasan: bad access detected [ 123.749562] [ 123.751241] Memory state around the buggy address: [ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 123.780904] ^ [ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 123.801883] ================================================================== Fixes: cf7221a4f5a5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23powerpc/mm/hash: Fix sharing context ids between kernel & userspaceAneesh Kumar K.V
Commit 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range") has a bug in the definition of MIN_USER_CONTEXT. The result is that the context id used for the vmemmap and the lowest context id handed out to userspace are the same. The context id is essentially the process identifier as far as the first stage of the MMU translation is concerned. This can result in multiple SLB entries with the same VSID (Virtual Segment ID), accessible to the kernel and some random userspace process that happens to get the overlapping id, which is not expected eg: 07 c00c000008000000 40066bdea7000500 1T ESID= c00c00 VSID= 66bdea7 LLP:100 12 0002000008000000 40066bdea7000d80 1T ESID= 200 VSID= 66bdea7 LLP:100 Even though the user process and the kernel use the same VSID, the permissions in the hash page table prevent the user process from reading or writing to any kernel mappings. It can also lead to SLB entries with different base page size encodings (LLP), eg: 05 c00c000008000000 00006bde0053b500 256M ESID=c00c00000 VSID= 6bde0053b LLP:100 09 0000000008000000 00006bde0053bc80 256M ESID= 0 VSID= 6bde0053b LLP: 0 Such SLB entries can result in machine checks, eg. as seen on a G5: Oops: Machine check, sig: 7 [#1] BE PAGE SIZE=64K MU-Hash SMP NR_CPUS=4 NUMA Power Mac NIP: c00000000026f248 LR: c000000000295e58 CTR: 0000000000000000 REGS: c0000000erfd3d70 TRAP: 0200 Tainted: G M (5.5.0-rcl-gcc-8.2.0-00010-g228b667d8ea1) MSR: 9000000000109032 <SF,HV,EE,ME,IR,DR,RI> CR: 24282048 XER: 00000000 DAR: c00c000000612c80 DSISR: 00000400 IRQMASK: 0 ... NIP [c00000000026f248] .kmem_cache_free+0x58/0x140 LR [c088000008295e58] .putname 8x88/0xa Call Trace: .putname+0xB8/0xa .filename_lookup.part.76+0xbe/0x160 .do_faccessat+0xe0/0x380 system_call+0x5c/ex68 This happens with 256MB segments and 64K pages, as the duplicate VSID is hit with the first vmemmap segment and the first user segment, and older 32-bit userspace maps things in the first user segment. On other CPUs a machine check is not seen. Instead the userspace process can get stuck continuously faulting, with the fault never properly serviced, due to the kernel not understanding that there is already a HPTE for the address but with inaccessible permissions. On machines with 1T segments we've not seen the bug hit other than by deliberately exercising it. That seems to be just a matter of luck though, due to the typical layout of the user virtual address space and the ranges of vmemmap that are typically populated. To fix it we add 2 to MIN_USER_CONTEXT. This ensures the lowest context given to userspace doesn't overlap with the VMEMMAP context, or with the context for INVALID_REGION_ID. Fixes: 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range") Cc: stable@vger.kernel.org # v5.2+ Reported-by: Christian Marillat <marillat@debian.org> Reported-by: Romain Dolbeau <romain@dolbeau.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> [mpe: Account for INVALID_REGION_ID, mostly rewrite change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200123102547.11623-1-mpe@ellerman.id.au
2020-01-23Merge branch 'r8152-serial-fixes'David S. Miller
Hayes Wang says: ==================== r8152: serial fixes v3: 1. Fix the typos for patch #5 and #6. 2. Modify the commit message of patch #9. v2: For patch #2, move declaring the variable "ocp_data". v1: These patches are used to fix some issues for RTL8153. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: disable DelayPhyPwrChgHayes Wang
When enabling this, the device would wait an internal signal which wouldn't be triggered. Then, the device couldn't enter P3 mode, so the power consumption is increased. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: avoid the MCU to clear the lanwakeHayes Wang
Avoid the MCU to clear the lanwake after suspending. It may cause the WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it and reset the lanwake status when resuming or initializing. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: don't enable U1U2 with USB_SPEED_HIGH for RTL8153BHayes Wang
For certain platforms, it causes USB reset periodically. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: disable test IO for RTL8153BHayes Wang
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause abnormal behavior for the device randomly. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: Disable PLA MCU clock speed downHayes Wang
PLA MCU clock speed down could only be enabled when tx/rx are disabled. Otherwise, the packet loss may occur. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: disable U2P3 for RTL8153BHayes Wang
Enable U2P3 may miss zero packet for bulk-in. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: get default setting of WOL before initializingHayes Wang
Initailization would reset runtime suspend by tp->saved_wolopts, so the tp->saved_wolopts should be set before initializing. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: reset flow control patch when linking on for RTL8153BHayes Wang
When linking ON, the patch of flow control has to be reset. This makes sure the patch works normally. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23r8152: fix runtime resume for linking changeHayes Wang
Fix the runtime resume doesn't work normally for linking change. 1. Reset the settings and status of runtime suspend. 2. Sync the linking status. 3. Poll the linking change. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23gtp: make sure only SOCK_DGRAM UDP sockets are acceptedEric Dumazet
A malicious user could use RAW sockets and fool GTP using them as standard SOCK_DGRAM UDP sockets. BUG: KMSAN: uninit-value in udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline] BUG: KMSAN: uninit-value in setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85 CPU: 0 PID: 11262 Comm: syz-executor613 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline] setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85 gtp_encap_enable_socket+0x37f/0x5a0 drivers/net/gtp.c:827 gtp_encap_enable drivers/net/gtp.c:844 [inline] gtp_newlink+0xfb/0x1e50 drivers/net/gtp.c:666 __rtnl_newlink net/core/rtnetlink.c:3305 [inline] rtnl_newlink+0x2973/0x3920 net/core/rtnetlink.c:3363 rtnetlink_rcv_msg+0x1153/0x1570 net/core/rtnetlink.c:5424 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x441359 Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fff1cd0ac28 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441359 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8 R10: 00000000004002c8 R11: 0000000000000246 R12: 00000000004020d0 R13: 0000000000402160 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags+0x3c/0x90 mm/kmsan/kmsan.c:144 kmsan_internal_alloc_meta_for_pages mm/kmsan/kmsan_shadow.c:307 [inline] kmsan_alloc_page+0x12a/0x310 mm/kmsan/kmsan_shadow.c:336 __alloc_pages_nodemask+0x57f2/0x5f60 mm/page_alloc.c:4800 alloc_pages_current+0x67d/0x990 mm/mempolicy.c:2207 alloc_pages include/linux/gfp.h:534 [inline] alloc_slab_page+0x111/0x12f0 mm/slub.c:1511 allocate_slab mm/slub.c:1656 [inline] new_slab+0x2bc/0x1130 mm/slub.c:1722 new_slab_objects mm/slub.c:2473 [inline] ___slab_alloc+0x1533/0x1f30 mm/slub.c:2624 __slab_alloc mm/slub.c:2664 [inline] slab_alloc_node mm/slub.c:2738 [inline] slab_alloc mm/slub.c:2783 [inline] kmem_cache_alloc+0xb23/0xd70 mm/slub.c:2788 sk_prot_alloc+0xf2/0x620 net/core/sock.c:1597 sk_alloc+0xf0/0xbe0 net/core/sock.c:1657 inet_create+0x7c7/0x1370 net/ipv4/af_inet.c:321 __sock_create+0x8eb/0xf00 net/socket.c:1420 sock_create net/socket.c:1471 [inline] __sys_socket+0x1a1/0x600 net/socket.c:1513 __do_sys_socket net/socket.c:1522 [inline] __se_sys_socket+0x8d/0xb0 net/socket.c:1520 __x64_sys_socket+0x4a/0x70 net/socket.c:1520 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pablo Neira <pablo@netfilter.org> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23net: rtnetlink: validate IFLA_MTU attribute in rtnl_create_link()Eric Dumazet
rtnl_create_link() needs to apply dev->min_mtu and dev->max_mtu checks that we apply in do_setlink() Otherwise malicious users can crash the kernel, for example after an integer overflow : BUG: KASAN: use-after-free in memset include/linux/string.h:365 [inline] BUG: KASAN: use-after-free in __alloc_skb+0x37b/0x5e0 net/core/skbuff.c:238 Write of size 32 at addr ffff88819f20b9c0 by task swapper/0/0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.5.0-rc1-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x197/0x210 lib/dump_stack.c:118 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374 __kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506 kasan_report+0x12/0x20 mm/kasan/common.c:639 check_memory_region_inline mm/kasan/generic.c:185 [inline] check_memory_region+0x134/0x1a0 mm/kasan/generic.c:192 memset+0x24/0x40 mm/kasan/common.c:108 memset include/linux/string.h:365 [inline] __alloc_skb+0x37b/0x5e0 net/core/skbuff.c:238 alloc_skb include/linux/skbuff.h:1049 [inline] alloc_skb_with_frags+0x93/0x590 net/core/skbuff.c:5664 sock_alloc_send_pskb+0x7ad/0x920 net/core/sock.c:2242 sock_alloc_send_skb+0x32/0x40 net/core/sock.c:2259 mld_newpack+0x1d7/0x7f0 net/ipv6/mcast.c:1609 add_grhead.isra.0+0x299/0x370 net/ipv6/mcast.c:1713 add_grec+0x7db/0x10b0 net/ipv6/mcast.c:1844 mld_send_cr net/ipv6/mcast.c:1970 [inline] mld_ifc_timer_expire+0x3d3/0x950 net/ipv6/mcast.c:2477 call_timer_fn+0x1ac/0x780 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x6c3/0x1790 kernel/time/timer.c:1786 __do_softirq+0x262/0x98c kernel/softirq.c:292 invoke_softirq kernel/softirq.c:373 [inline] irq_exit+0x19b/0x1e0 kernel/softirq.c:413 exiting_irq arch/x86/include/asm/apic.h:536 [inline] smp_apic_timer_interrupt+0x1a3/0x610 arch/x86/kernel/apic/apic.c:1137 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829 </IRQ> RIP: 0010:native_safe_halt+0xe/0x10 arch/x86/include/asm/irqflags.h:61 Code: 98 6b ea f9 eb 8a cc cc cc cc cc cc e9 07 00 00 00 0f 00 2d 44 1c 60 00 f4 c3 66 90 e9 07 00 00 00 0f 00 2d 34 1c 60 00 fb f4 <c3> cc 55 48 89 e5 41 57 41 56 41 55 41 54 53 e8 4e 5d 9a f9 e8 79 RSP: 0018:ffffffff89807ce8 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13 RAX: 1ffffffff13266ae RBX: ffffffff8987a1c0 RCX: 0000000000000000 RDX: dffffc0000000000 RSI: 0000000000000006 RDI: ffffffff8987aa54 RBP: ffffffff89807d18 R08: ffffffff8987a1c0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: dffffc0000000000 R13: ffffffff8a799980 R14: 0000000000000000 R15: 0000000000000000 arch_cpu_idle+0xa/0x10 arch/x86/kernel/process.c:690 default_idle_call+0x84/0xb0 kernel/sched/idle.c:94 cpuidle_idle_call kernel/sched/idle.c:154 [inline] do_idle+0x3c8/0x6e0 kernel/sched/idle.c:269 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:361 rest_init+0x23b/0x371 init/main.c:451 arch_call_rest_init+0xe/0x1b start_kernel+0x904/0x943 init/main.c:784 x86_64_start_reservations+0x29/0x2b arch/x86/kernel/head64.c:490 x86_64_start_kernel+0x77/0x7b arch/x86/kernel/head64.c:471 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:242 The buggy address belongs to the page: page:ffffea00067c82c0 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 raw: 057ffe0000000000 ffffea00067c82c8 ffffea00067c82c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88819f20b880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88819f20b900: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff88819f20b980: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff88819f20ba00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88819f20ba80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23airo: Add missing CAP_NET_ADMIN check in AIROOLDIOCTL/SIOCDEVPRIVATEMichael Ellerman
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c), implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl(). The ioctl handler copies an aironet_ioctl struct from userspace, which includes a command. Some of the commands are handled in readrids(), where the user controlled command is converted into a driver-internal value called "ridcode". There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM respectively. These commands both have checks that the user has CAP_NET_ADMIN, with the comment that "Only super-user can read WEP keys", otherwise they return -EPERM. However there is another command value, AIRORRID, that lets the user specify the ridcode value directly, with no other checks. This means the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and AIROGWEPKNV. Fix it by moving the CAP_NET_ADMIN check out of the command handling and instead do it later based on the ridcode. That way regardless of whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed in using AIRORID, we always do the CAP_NET_ADMIN check. Found by Ilja by code inspection, not tested as I don't have the required hardware. Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23airo: Fix possible info leak in AIROOLDIOCTL/SIOCDEVPRIVATEMichael Ellerman
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c), implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl(). The ioctl handler copies an aironet_ioctl struct from userspace, which includes a command and a length. Some of the commands are handled in readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes. That buffer is then passed to PC4500_readrid(), which has two cases. The else case does some setup and then reads up to RIDSIZE bytes from the hardware into the kmalloc()'ed buffer. Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer: // read the rid length field bap_read(ai, pBuf, 2, BAP1); // length for remaining part of rid len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2; ... // read remainder of the rid rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1); PC4500_readrid() then returns to readrids() which does: len = comp->len; if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) { Where comp->len is the user controlled length field. So if the "rid length field" returned by the hardware is < 2048, and the user requests 2048 bytes in comp->len, we will leak the previous contents of the kmalloc()'ed buffer to userspace. Fix it by kzalloc()'ing the buffer. Found by Ilja by code inspection, not tested as I don't have the required hardware. Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23tee: optee: Fix compilation issue with nommuVincenzo Frascino
The optee driver uses specific page table types to verify if a memory region is normal. These types are not defined in nommu systems. Trying to compile the driver in these systems results in a build error: linux/drivers/tee/optee/call.c: In function ‘is_normal_memory’: linux/drivers/tee/optee/call.c:533:26: error: ‘L_PTE_MT_MASK’ undeclared (first use in this function); did you mean ‘PREEMPT_MASK’? return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC; ^~~~~~~~~~~~~ PREEMPT_MASK linux/drivers/tee/optee/call.c:533:26: note: each undeclared identifier is reported only once for each function it appears in linux/drivers/tee/optee/call.c:533:44: error: ‘L_PTE_MT_WRITEALLOC’ undeclared (first use in this function) return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC; ^~~~~~~~~~~~~~~~~~~ Make the optee driver depend on MMU to fix the compilation issue. Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> [jw: update commit title] Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
2020-01-23MAINTAINERS: Make Russell King designated reviewer of phylibAndrew Lunn
phylink and phylib are interconnected. It makes sense for phylib and phy driver patches to be also reviewed by the phylink maintainer. So add Russell King as a designed reviewer of phylib. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23Merge tag 'drm-misc-fixes-2020-01-22-1' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes -mst: Fix SST branch device handling (Wayne) -panfrost: Fix mapping of globally visible BO's (Boris) Cc: Wayne Lin <Wayne.Lin@amd.com> CC: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Dave Airlie <airlied@redhat.com> From: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200122213725.GA22099@art_vandelay
2020-01-23cpufreq: loongson2_cpufreq: adjust cpufreq uses of LOONGSON_CHIPCFGAlexandre Oliva
The post-fork cleanup of loongson2ef from loongson64 changed LOONGSON_CHIPCFG from a single-argument functional macro to a non-functional macro with an mmio address in loongson2ef, but loongson2_cpufreq still uses the notation of a functional macro call expecting it to be an lvalue. Fixed based on loongson_suspend_enter. Signed-off-by: Alexandre Oliva <lxoliva@fsfla.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Clean up irtl_2_usec()Rafael J. Wysocki
Move the irtl_ns_units[] definition into irtl_2_usec() which is the only user of it, use div_u64() for the division in there (as the divisor is small enough) and use the NSEC_PER_USEC symbol for the divisor. Also convert the irtl_2_usec() comment to a proper kerneldo one. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-01-23intel_idle: Move 3 functions closer to their callersRafael J. Wysocki
Move intel_idle_verify_cstate(), auto_demotion_disable() and c1e_promotion_disable() closer to their callers. While at it, annotate intel_idle_verify_cstate() with __init, as it is only used during the initialization of the driver. No intentional functional impact. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
generated by cgit (git 2.34.1) at 2025-09-12 02:41:54 +0000