| Age | Commit message (Collapse) | Author |
|---|
|
Support for reducing the number of nodes and memory consumption of the rbtree
cache by allowing for small unused holes in the node's register cache block was
initially added in commit 0c7ed856 ("regmap: Cut down on the average # of nodes
in the rbtree cache"). But the commit had problems and so its effect was
reverted again in commit 4e67fb5 ("regmap: rbtree: Fix overlapping rbnodes.").
This patch brings the feature back of reducing the average number of nodes,
which will speedup node look-up, while at the same time also reducing the memory
usage of the rbtree cache. This patch takes a slightly different approach than
the original patch though. It modifies the adjacent node look-up to not only
consider nodes that are just one to the left or the right of the register but
any node that falls in a certain range around the register. The range is
calculated based on how much memory it would take to allocate a new node
compared to how much memory it takes adding a set of unused registers to an
existing node. E.g. if a node takes up 24 bytes and each register in a block
uses 1 byte the range will be from the register address - 24 to the register
address + 24. If we find a node that falls within this range it is cheaper or as
expensive to add the register to the existing node and have a couple of unused
registers in the node's cache compared to allocating a new node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
A register which is adjacent to a node will either be left to the first
register or right to the last register. It will not be within the node's range,
so there is no point in checking for each register cached by the node whether
the new register is next to it. It is sufficient to check whether the register
comes before the first register or after the last register of the node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch implements a device-tree-only machine driver for Freescale
i.MX series Soc. It works with spdif_transmitter/spdif_receiver and
fsl_spdif.c drivers.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The last remaining use for the storage key of the s390 architecture
is reference counting. The alternative is to make page table entries
invalid while they are old. On access the fault handler marks the
pte/pmd as young which makes the pte/pmd valid if the access rights
allow read access. The pte/pmd invalidations required for software
managed reference bits cost a bit of performance, on the other hand
the RRBE/RRBM instructions to read and reset the referenced bits are
quite expensive as well.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch adds support for QSFP active direct attach (DA) cables which
pre-date SFF-8436 v3.6.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch makes sure that QSFP+ modules use the SFP+ code path for
setting up link.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds GB speed support for QSFP+ modules.
Autonegotiation is not supported with QSFP+. The user will have to set
the desired speed on both link partners using ethtool advertise setting.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes the read loop for the I2C data to account for the offset.
Also includes a whitespace cleanup and removes ret_val as it is not needed.
CC: Ben Hutchings <bhutchings@solarflare.com>
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Some minor log messages cleanup, changing the level one message is logged,
adding a bit of detail to another and put all the text on one line.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch initializes the msgbuf array to 0 in order to avoid using random
numbers from the memory as MAC address for the VF.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
* Don't install scripting files files when perl/python support is disabled.
* Support ! in -e expressions in 'perf trace', to filter a list of syscalls.
* Add --verbose and -o/--output options to 'perf trace'.
* Introduce better formatting of syscall arguments in 'perf trace',
including so far beautifiers for mmap, madvise, syscall return
values.
* Fixup jobserver setup in libtraceevent makefile.
* Debug improvements from Adrian Hunter.
* Try to increase the file descriptor limits on EMFILE, from Andi Kleen.
* Remove unused force option in 'perf kvm', from David Ahern.
* Make 'perf trace' command line arguments consistent with 'perf record',
from David Ahern.
* Fix correlation of samples coming after PERF_RECORD_EXIT event, from
David Ahern.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pick up the latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch is a partial reverse of:
commit dfcc4615f09c33454bc553567f7c7506cae60cb9
Author: Jacob Keller <jacob.e.keller@intel.com>
Date: Thu Nov 8 07:07:08 2012 +0000
ixgbe: ethtool ixgbe_diag_test cleanup
Specifically forcing the laser before the link check can lead to
inconsistent results because it does not guarantee that the link will be
negotiated correctly. Such is the case when dual speed SFP+ module is
connected to a gigabit link partner.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were transversing the tx_ring with IXGBE_NUM_RX_QUEUES. Now this define
happens to have the correct value but this is misleading and a change later
could easily make this no longer true. I updated it to netdev->num_tx_queues
like we use in ixgbe_get_strings().
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes the possible use of uninitialized memory by checking the
return value on eeprom reads. These issues were identified by static
analysis. In many cases error messages will be produced so that corrupted
eeprom issues will be more visible.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes an issue with the 82599 adapter where it can potentially keep
link lights up when the adapter has gone down. The patch adds a function which
ensures link is disabled, and calls this function when the adapter transitions
to a down state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The "Report ID" field of a HID report is used to build indexes of
reports. The kernel's index of these is limited to 256 entries, so any
malicious device that sets a Report ID greater than 255 will trigger
memory corruption on the host:
[ 1347.156239] BUG: unable to handle kernel paging request at ffff88094958a878
[ 1347.156261] IP: [<ffffffff813e4da0>] hid_register_report+0x2a/0x8b
CVE-2013-2888
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
It does not make sense to show ti prefix in pinconf_generic_dt_subnode_to_map()
dev_err messages.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Merged in this to avoid conflicts with the big locking fixes
from upstream.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/pinctrl/pinctrl-sunxi.c
|
|
vcpu in page_fault_can_be_fast() is not used so remove it
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
Implement .request() and .free() callbacks on the GPIO chips to
inform pinctrl when a GPIO is requested or freed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
1. Further cleanup and refactoring in preparation for EF10.
2. Remove ethtool stats that are always zero on Falcon boards.
3. Add an ethtool stat for merged TX completions.
4. Prepare to support merged RX completions.
5. Prepare to support more hwmon sensors.
6. Add support for new events that are generated by EF10 firmware.
7. Update MC reboot detection for EF10.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Included changes:
- set the protocol field in the skb structure according to the encapsulated
payload
- make the gateway component send a uevent in case of "gw client mode"
de-selection
- increment version number
- minor code rearrangement
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function checks the upper bound but it doesn't check for negative
numbers:
if (txq > QLCNIC_MAX_TX_RINGS) {
I've solved this by making "txq" a u32 type. I chose that because
->tx_count in the ethtool_channels struct is a __u32.
This bug was added in aa4a1f7df7 ('qlcnic: Enable Tx queue changes using
ethtool for 82xx Series adapter.').
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wei Liu says:
====================
xen-netback: switch to NAPI + kthread 1:1 model
This series implements NAPI + kthread 1:1 model for Xen netback.
This model
- provides better scheduling fairness among vifs
- is prerequisite for implementing multiqueue for Xen network driver
The second patch has the real meat:
- make use of NAPI to mitigate interrupt
- kthreads are not bound to CPUs any more, so that we can take
advantage of backend scheduler and trust it to do the right thing
Benchmark is done on a Dell T3400 workstation with 4 cores, running 4
DomUs. Netserver runs in Dom0. DomUs do netperf to Dom0 with
following command: /root/netperf -H Dom0 -fm -l120
IRQs are distributed to 4 cores by hand in the new model, while in the
old model vifs are automatically distributed to 4 kthreads.
* New model
%Cpu0 : 0.5 us, 20.3 sy, 0.0 ni, 28.9 id, 0.0 wa, 0.0 hi, 24.4 si, 25.9 st
%Cpu1 : 0.5 us, 17.8 sy, 0.0 ni, 28.8 id, 0.0 wa, 0.0 hi, 27.7 si, 25.1 st
%Cpu2 : 0.5 us, 18.8 sy, 0.0 ni, 30.7 id, 0.0 wa, 0.0 hi, 22.9 si, 27.1 st
%Cpu3 : 0.0 us, 20.1 sy, 0.0 ni, 30.4 id, 0.0 wa, 0.0 hi, 22.7 si, 26.8 st
Throughputs: 2027.89 2025.95 2018.57 2016.23 aggregated: 8088.64
* Old model
%Cpu0 : 0.5 us, 68.8 sy, 0.0 ni, 16.1 id, 0.5 wa, 0.0 hi, 2.8 si, 11.5 st
%Cpu1 : 0.4 us, 45.1 sy, 0.0 ni, 31.1 id, 0.4 wa, 0.0 hi, 2.1 si, 20.9 st
%Cpu2 : 0.9 us, 44.8 sy, 0.0 ni, 30.9 id, 0.0 wa, 0.0 hi, 1.3 si, 22.2 st
%Cpu3 : 0.8 us, 46.4 sy, 0.0 ni, 28.3 id, 1.3 wa, 0.0 hi, 2.1 si, 21.1 st
Throughputs: 1899.14 2280.43 1963.33 1893.47 aggregated: 8036.37
We can see that the impact is mainly on CPU usage. The new model moves
processing from kthread to NAPI (software interrupt).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we move to 1:1 model and melt xen_netbk and xenvif together, it would
be better to use single prefix for all functions in xen-netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements 1:1 model netback. NAPI and kthread are utilized
to do the weight-lifting job:
- NAPI is used for guest side TX (host side RX)
- kthread is used for guest side RX (host side TX)
Xenvif and xen_netbk are made into one structure to reduce code size.
This model provides better scheduling fairness among vifs. It is also
prerequisite for implementing multiqueue for Xen netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data flow from DomU to DomU on the same host in current copying
scheme with tracking facility:
copy
DomU --------> Dom0 DomU
| ^
|____________________________|
copy
The page in Dom0 is a page with valid MFN. So we can always copy from
page Dom0, thus removing the need for a tracking facility.
copy copy
DomU --------> Dom0 -------> DomU
Simple iperf test shows no performance regression (obviously we copy
twice either way):
W/ tracking: ~5.3Gb/s
W/o tracking: ~5.4Gb/s
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Matt Wilson <msw@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
padata_cpu_callback() takes pinst->lock, to avoid taking
an uninitialized lock, register the notifier after it's
initialization.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
CPU_DOWN_PREPARE and CPU_UP_CANCELED
Share code between CPU_ONLINE and CPU_DOWN_FAILED, same to
CPU_DOWN_PREPARE and CPU_UP_CANCELED.
It will fix 2 bugs:
"not check the return value of __padata_remove_cpu() and __padata_add_cpu()".
"need add 'break' between CPU_UP_CANCELED and CPU_DOWN_FAILED".
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Don't allow mounting sysfs unless the caller has CAP_SYS_ADMIN rights
over the net namespace. The principle here is if you create or have
capabilities over it you can mount it, otherwise you get to live with
what other people have mounted.
Instead of testing this with a straight forward ns_capable call,
perform this check the long and torturous way with kobject helpers,
this keeps direct knowledge of namespaces out of sysfs, and preserves
the existing sysfs abstractions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
This hooks nouveau up to the runtime PM system to enable
dynamic power management for secondary GPUs in switchable
and optimus laptops.
a) rewrite suspend/resume printks to hide them during dynamic s/r
to avoid cluttering logs
b) add runtime pm suspend to irq handler, crtc display, ioctl handler,
connector status,
c) handle hdmi audio dynamic power on/off using magic register.
v0.5:
make sure we hit D3 properly
fix fbdev_set_suspend locking interaction, we only will poweroff if we have no
active crtcs/fbcon anyways.
add reference for active crtcs.
sprinkle mark last busy for autosuspend timeout
v0.6:
allow more flexible debugging - to avoid log spam
add option to enable/disable dynpm
got to D3Cold
v0.7:
add hdmi audio support.
v0.8:
call autosuspend from idle, so pci config space access doesn't go straight
back to sleep, this makes starting X faster.
only signal usage if we actually handle the irq, otherwise usb keeps us awake.
fix nv50 display active powerdown
v0.9:
use masking function to enable hdmi audio
set busy when we fail to suspend
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Add support for HDMI audio device on VGA cards that powerdown
to D3cold using non-standard ACPI/PCI infrastructure (optimus).
This does a couple of things to make it work:
a) add a set of power ops for the hdmi domain, and enables them
via vga_switcheroo when we are a switcheroo controlled card. This
just replaces the runtime resume operation so that when the card
is in D3cold the userspace pci config space access via sysfs,
the vga switcheroon runtime resume gets called first and it calls
the GPU resume callback before calling the sound card runtime
resume.
b) standard ACPI/PCI stacks won't put a device into D3cold without
an ACPI handle, but since the hdmi audio devices on gpus don't have
an ACPI handle, we need to manually force the device into D3cold
after suspend from the switcheroo path only.
c) don't try and do runtime s/r when the GPU is off.
d) call runtime suspend/resume during switcheroo suspend/resume
this is to make sure the runtime stack knows to try and resume
the hdmi audio device for pci config space access.
v2: fix incorrect runtime call suspend->resume.
v3: rework irq handler to avoid false irq when we are resuming
but haven't runtime resumed yet, don't bother trying D3cold,
it won't work, just set it manually ourselves, move runtime s/r
calls outside the main s/r hook. enable dnyamic pm properly by
dropping reference.
v4: put back irq handler check just wrap it with cap check
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
For optimus and powerxpress muxless we really want the GPU
driver deciding when to power up/down the GPU, not userspace.
This adds the ability for a driver to dynamically power up/down
the GPU and remove the switcheroo from controlling it, the
switcheroo reports the dynamic state to userspace also.
It also adds 2 power domains, one for machine where the power
switch is controlled outside the GPU D3 state, so the powerdown
ordering is done correctly, and the second for the hdmi audio
device to make sure it can resume for PCI config space accesses.
v1.1: fix build with switcheroo off
v2: add power domain support for radeon and v1 nvidia dsms
v2.1: fix typo in off case
v3: add audio power domain for hdmi audio + misc audio fixes
v4: use PCI_SLOT macro, drop power reference on hdmi audio resume
failure also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* pci/misc:
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
|
|
pcie_cap_has_devctl() does nothing, so remove it. Simplicity over
consistency in this case. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
|
|
Previously we allowed callers to access Slot Capabilities, Status, and
Control for Root Ports even if the Root Port did not implement a slot.
This seems dubious because the spec only requires these registers if a
slot is implemented.
It's true that even Root Ports without slots must have *space* for these
slot registers, because the Root Capabilities, Status, and Control
registers are after the slot registers in the capability. However,
for a v1 PCIe Capability, the *semantics* of the slot registers are
undefined unless a slot is implemented.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
|
|
Previously we relied on the PCIe r3.0, sec 7.8, spec language that says
"For Functions that do not implement the [Link, Slot, Root] registers,
these spaces must be hardwired to 0b," which means that for v2 PCIe
capabilities, we don't need to check the device type at all.
But it's simpler if we don't need to check the capability version at all,
and I think the spec is explicit enough about which registers are required
for which types that we can remove the version checks.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Jiang Liu <jiang.liu@huawei.com>
|
|
Merge fixes from Andrew Morton:
"Five fixes.
err, make that six. let me try again"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
fs/ocfs2/super.c: Use bigger nodestr to accomodate 32-bit node numbers
memcg: check that kmem_cache has memcg_params before accessing it
drivers/base/memory.c: fix show_mem_removable() to handle missing sections
IPC: bugfix for msgrcv with msgtyp < 0
Omnikey Cardman 4000: pull in ioctl.h in user header
timer_list: correct the iterator for timer_list
|
|
While using pacemaker/corosync, the node numbers are generated using IP
address as opposed to serial node number generation. This may not fit
in a 8-byte string. Use a bigger string to print the complete node
number.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the system had a few memory groups and all of them were destroyed,
memcg_limited_groups_array_size has non-zero value, but all new caches
are created without memcg_params, because memcg_kmem_enabled() returns
false.
We try to enumirate child caches in a few places and all of them are
potentially dangerous.
For example my kernel is compiled with CONFIG_SLAB and it crashed when I
tryed to mount a NFS share after a few experiments with kmemcg.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff8118166a>] do_tune_cpucache+0x8a/0xd0
PGD b942a067 PUD b999f067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: fscache(+) ip6table_filter ip6_tables iptable_filter ip_tables i2c_piix4 pcspkr virtio_net virtio_balloon i2c_core floppy
CPU: 0 PID: 357 Comm: modprobe Not tainted 3.11.0-rc7+ #59
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task: ffff8800b9f98240 ti: ffff8800ba32e000 task.ti: ffff8800ba32e000
RIP: 0010:[<ffffffff8118166a>] [<ffffffff8118166a>] do_tune_cpucache+0x8a/0xd0
RSP: 0018:ffff8800ba32fb70 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000006
RDX: 0000000000000000 RSI: ffff8800b9f98910 RDI: 0000000000000246
RBP: ffff8800ba32fba0 R08: 0000000000000002 R09: 0000000000000004
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000010
R13: 0000000000000008 R14: 00000000000000d0 R15: ffff8800375d0200
FS: 00007f55f1378740(0000) GS:ffff8800bfa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f24feba57a0 CR3: 0000000037b51000 CR4: 00000000000006f0
Call Trace:
enable_cpucache+0x49/0x100
setup_cpu_cache+0x215/0x280
__kmem_cache_create+0x2fa/0x450
kmem_cache_create_memcg+0x214/0x350
kmem_cache_create+0x2b/0x30
fscache_init+0x19b/0x230 [fscache]
do_one_initcall+0xfa/0x1b0
load_module+0x1c41/0x26d0
SyS_finit_module+0x86/0xb0
system_call_fastpath+0x16/0x1b
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
"cat /sys/devices/system/memory/memory*/removable" crashed the system.
The problem is that show_mem_removable() is passing a
bad pfn to is_mem_section_removable(), which causes
if (!node_online(page_to_nid(page)))
to blow up. Why is it passing in a bad pfn?
The reason is that show_mem_removable() will loop sections_per_block
times. sections_per_block is 16, but mem->section_count is 8,
indicating holes in this memory block. Checking that the memory section
is present before checking to see if the memory section is removable
fixes the problem.
harp5-sys:~ # cat /sys/devices/system/memory/memory*/removable
0
1
1
1
1
1
1
1
1
1
1
1
1
1
BUG: unable to handle kernel paging request at ffffea00c3200000
IP: [<ffffffff81117ed1>] is_pageblock_removable_nolock+0x1/0x90
PGD 83ffd4067 PUD 37bdfce067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: autofs4 binfmt_misc rdma_ucm rdma_cm iw_cm ib_addr ib_srp scsi_transport_srp scsi_tgt ib_ipoib ib_cm ib_uverbs ib_umad iw_cxgb3 cxgb3 mdio mlx4_en mlx4_ib ib_sa mlx4_core ib_mthca ib_mad ib_core fuse nls_iso8859_1 nls_cp437 vfat fat joydev loop hid_generic usbhid hid hwperf(O) numatools(O) dm_mod iTCO_wdt ipv6 iTCO_vendor_support igb i2c_i801 ioatdma i2c_algo_bit ehci_pci pcspkr lpc_ich i2c_core ehci_hcd ptp sg mfd_core dca rtc_cmos pps_core mperf button xhci_hcd sd_mod crc_t10dif usbcore usb_common scsi_dh_emc scsi_dh_hp_sw scsi_dh_alua scsi_dh_rdac scsi_dh gru(O) xvma(O) xfs crc32c libcrc32c thermal sata_nv processor piix mptsas mptscsih scsi_transport_sas mptbase megaraid_sas fan thermal_sys hwmon ext3 jbd ata_piix ahci libahci libata scsi_mod
CPU: 4 PID: 5991 Comm: cat Tainted: G O 3.11.0-rc5-rja-uv+ #10
Hardware name: SGI UV2000/ROMLEY, BIOS SGI UV 2000/3000 series BIOS 01/15/2013
task: ffff88081f034580 ti: ffff880820022000 task.ti: ffff880820022000
RIP: 0010:[<ffffffff81117ed1>] [<ffffffff81117ed1>] is_pageblock_removable_nolock+0x1/0x90
RSP: 0018:ffff880820023df8 EFLAGS: 00010287
RAX: 0000000000040000 RBX: ffffea00c3200000 RCX: 0000000000000004
RDX: ffffea00c30b0000 RSI: 00000000001c0000 RDI: ffffea00c3200000
RBP: ffff880820023e38 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000001 R12: ffffea00c33c0000
R13: 0000160000000000 R14: 6db6db6db6db6db7 R15: 0000000000000001
FS: 00007ffff7fb2700(0000) GS:ffff88083fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffea00c3200000 CR3: 000000081b954000 CR4: 00000000000407e0
Call Trace:
show_mem_removable+0x41/0x70
dev_attr_show+0x2a/0x60
sysfs_read_file+0xf7/0x1c0
vfs_read+0xc8/0x130
SyS_read+0x5d/0xa0
system_call_fastpath+0x16/0x1b
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to 'man msgrcv': "If msgtyp is less than 0, the first message of
the lowest type that is less than or equal to the absolute value of msgtyp
shall be received."
Bug: The kernel only returns a message if its type is 1; other messages
with type < abs(msgtype) will never get returned.
Fix: After having traversed the list to find the first message with the
lowest type, we need to actually return that message.
This regression was introduced by commit daaf74cf0867 ("ipc: refactor
msg list search into separate function")
Signed-off-by: Svenning Soerensen <sss@secomea.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This file uses the ioctl helpers (_IOR/_IOW/etc...), so include ioctl.h
for the definitions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Correct an issue with /proc/timer_list reported by Holger.
When reading from the proc file with a sufficiently small buffer, 2k so
not really that small, there was one could get hung trying to read the
file a chunk at a time.
The timer_list_start function failed to account for the possibility that
the offset was adjusted outside the timer_list_next.
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Reported-by: Holger Hans Peter Freyther <holger@freyther.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Berke Durak <berke.durak@xiphos.com>
Cc: Jeff Layton <jlayton@redhat.com>
Tested-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
