| Age | Commit message (Collapse) | Author |
|---|
|
AM437x IDK has a TPS386000 supply voltage supervisor on the VDD_MPU rail
set to trigger undervoltage condition at 0.96V. Because of this, OPP50,
which is normally configured to 300MHz at 0.95V, must be disabled to
avoid triggering the undervoltage condition. Also mark OPP100 as the
suspend-opp as it is now our lowest OPP.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can remove the unnecessary "omapdss," prefix because
the omapdrm driver takes care of it when matching with
the driver table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM64 Based SoC DT Updates for v4.16" from Simon Horman:
* Use r8a77970 (V3M) CPG core clock and SYSC power domain macros
These may be used in place of numeric constants now that they
are present in Linus's tree.
* Add r8a77970 (V3M) Starter Kit board support
This includes basic support to bring up the board with a serial
console and EtherAVB support
* Add IPMMU nodes and connections to on-chip devices
on r8a7795 (H3), r8a7796 (M3-W), r8a77970 (V3M) and r8a77995 (D3) SoCs
Simon Horman says "With these patches applied a white list enabled IPMMU
driver may be used to check silicon revision and then enable IPMMU in the
known working cases."
* Enable DMA for SCIF2 on r8a77995 (D2) SoC
* Increase the number of GPIO bank 1 ports to 29 on r8a7795 (H3) SoC
This adds support for the GP-1-28 port pin of the r8a7795 (H3) ES2.0 SoC
* Add support for CAN to r8a77995 (D3) SoC
Ulrich Hecht says "This is a by-the-datasheet implementation, with the
datasheet missing some bits, namely the pin map. I filled in the gaps...
by deducing the information from pin numbers already in the PFC driver,
so careful scrutiny is advised."
* Add support for SDHI to r8a77995 (D3) SoC
* Add SoC name to file header of r8a7795 (H3) and r8a7796 (M3-W)
Salvator-X and Salvator-XS board files
Geert Uytterhoeven says "With the proliferation of Salvator-X and
Salvator-XS boards carrying different R-Car Gen3 SoCs variants, several
DTS files ended up having the same file headers.
Add the SoC names to the file headers to avoid confusion."
* Add device note for ROHM BD9571MWV PMIC to
r8a7795 (H3) and r8a7796 (M3-W) Salvator-X and Salvator-XS boards.
Geert Uytterhoeven says "This was based on the example in the DT binding
documentation, but using IRQ0 instead of a GPIO interrupt, as that
matches the schematics, and because INTC-EX is a simpler block."
* Enable USB2.0 channel 0 on r8a77970 (V3M) ULCB Kingfisher board
Vladimir Barinov says "The dedicated USB0_PWEN pin is used to control
CN13 VBUS source from U43 power supply. MAX3355 can also provide VBUS,
hence it should be disabled via OTG_OFFVBUSn node coming from gpio
expander TCA9539. Set MAX3355 enabled using OTG_EXTLPn node to be able
to read OTG ID of CN13."
* Add support for r8a7795 (M3-W) Salvator-XS board
Geert Uytterhoeven says "This patch series adds support for the version
of the Salvator-XS development board equipped with an R-Car M3-W SiP.
The DT was based on work for the Salvator-X and -XS boards with M3-W
resp. H3 SiPs."
* Add watchdog timer support to r8a77970 (V3M) eagle board
Geert Uytterhoven says "This allows to use the watchdog timer to reset
the board, until PSCI is enhanced to include such functionality."
* Use Use R-Car SDHI Gen3 fallback on r8a7795 (H3) and r8a7796 (M3-W) SoCs
* Set driver type for MMC on r8a7795 (H3) and r8a7796 (M3-W) Salvator-X and
Salvator-XS boards.
Wolfram Sang says "These boards are known to have eMMC issues with the
default driver type. Specify a working one."
* tag 'renesas-arm64-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (54 commits)
arm64: dts: renesas: r8a77970: use SYSC power domain macros
arm64: dts: renesas: r8a77970: use CPG core clock macros
arm64: dts: renesas: v3msk: add EtherAVB support
arm64: dts: renesas: initial V3MSK board device tree
arm64: dts: renesas: r8a77995: Connect Ethernet-AVB to IPMMU-RT
arm64: dts: renesas: r8a77995: Add IPMMU device nodes
arm64: dts: renesas: r8a77970: Enable IPMMU-DS1, RT and MM
arm64: dts: renesas: r8a77970: Connect Ethernet-AVB to IPMMU-RT
arm64: dts: renesas: r8a77970: Tie SYS-DMAC to IPMMU-DS1
arm64: dts: renesas: r8a77970: Add IPMMU device nodes
arm64: dts: renesas: r8a77995: add DMA for SCIF2
arm64: dts: renesas: r8a77970: sort includes
arm64: dts: renesas: r8a7795: Increase the number of GPIO bank 1 ports to 29
arm64: dts: renesas: r8a77995: Add CAN FD support
arm64: dts: renesas: r8a77995: Add CAN support
arm64: dts: renesas: r8a77995: Add CAN external clock support
arm64: dts: renesas: r8a7795-salvator-xs: Add SoC name to file header
arm64: dts: renesas: r8a7796-salvator-x: Add SoC name to file header
arm64: dts: renesas: r8a7795-salvator-x: Add SoC name to file header
arm64: dts: renesas: r8a7795-es1-salvator-x: Add SoC name to file header
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.16" from Simon Horman:
* Convert to named i2c-gpio bindings
Geert Uytterhoeven says "Commits 7d29f509d2cfd807 ("dt-bindings: i2c:
i2c-gpio: Add support for named gpios") and 05c74778858d7d99 ("i2c: gpio:
Add support for named gpios in DT") introduced named i2c-gpio DT
bindings, and deprecated the more error-prone unnamed variant.
This patch series switches all Renesas boards to the new bindings, and
adds the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly
assumed before..."
... Note that after this series is applied, the i2c-gpio buses are no
longer detected when booting new DTBs on old (v4.14 and older) kernels,
which should not be an issue. Booting old DTBs on new kernels is not
affected."
* Update DTS for CMT DT binding rework
Geert Uytterhoeven says "This patch series updates the CMT device nodes
in the various Renesas DTS files sh_cmt clocksource driver for the recent
DT binding rework that was merged in v4.14-rc1 and v4.15-rc1..."
* Add SMP support to r8a7794 (R-Car E2) SoC
Sergei Shtylyov says "Add the device tree node for the Advanced Power
Management Unit (APMU). Use the "enable-method" prop to point out that
the APMU should be used for the SMP support."
* Correct primary compatible value for eeprom
on r7s72100 (RZ/A1H) genmai and r8a7791 (R-Car M2-W) koelsh boards
Geert Uytterhoeven says "The Renesas part numbers of the two-wire serial
interface EEPROMs do not follow the 24Cxx pattern, but the R1EX24xxx
pattern.
Hence change the primary compatible values to the appropriate variant of
"renesas,r1ex24xxx", like is already done on Gose.""
* Move cec_clock to root node on r8a7791 (R-Car M2-W) koelsh board
r8a7791 (R-Car M2-W) koelsh board
* Use R-Car SDHI and Ether Gen1 and 2 fallback compat strings
Use recently posted R-Car SDHI and Ether Gen 1 and 2 fallback
compat strings in the DT of Renesas ARM based SoCs.
* Add IIC cores to dtsi of r8a7745 (RZ/G1E) SoC
* Rework DT architecture for r8a7745 (RZ/G1E) iW-RainboW-G22D development
platform and add serial support.
Fabrizio Castro says "... define a new DT architecture for the
iW-RainboW-G22D SODIMM Development Platform to include the configuration
with the HDMI daughter board and to define the serial interfaces."
* Add USB function support to
r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
* Add PCIEC and ttySC3 support to r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
* Add VIN support to r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
* Add CAN and HDMI support to r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
* tag 'renesas-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (61 commits)
ARM: dts: alt: Convert to named i2c-gpio bindings
ARM: dts: koelsch: Convert to named i2c-gpio bindings
ARM: dts: lager: Convert to named i2c-gpio bindings
ARM: dts: armadillo800eva: Convert to named i2c-gpio bindings
ARM: dts: sh73a0: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Remove CMT renesas,channels-mask
ARM: dts: r8a7793: Remove CMT renesas,channels-mask
ARM: dts: r8a7791: Remove CMT renesas,channels-mask
ARM: dts: r8a7790: Remove CMT renesas,channels-mask
ARM: dts: r8a7740: Remove CMT renesas,channels-mask
ARM: dts: r8a73a4: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Update CMT compat strings
ARM: dts: r8a7793: Update CMT compat strings
ARM: dts: r8a7791: Update CMT compat strings
ARM: dts: r8a7790: Update CMT compat strings
ARM: dts: r8a73a4: Update CMT compat string
ARM: dts: r8a7794: Add SMP support
ARM: dts: genmai: Correct primary compatible value for eeprom
ARM: dts: koelsch: Correct primary compatible value for eeprom
ARM: dts: r8a7745: add VIN dt support
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Bindings Updates for v4.16" from Simon Horman:
* Document V3MSK board bindings
These are the bindings for the R-Car V3M Starter Kit
* Document M3-W-based Salvator-XS board bingigns
Geert Uytterhoeven says "The Renesas Salvator-XS (Salvator-X 2nd version)
development board can be equipped with either an R-Car H3 ES2.0 or M3-W
ES1.x SiP, which are pin-compatible."
* tag 'renesas-dt-bindings-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: document V3MSK board bindings
ARM: shmobile: Document Renesas M3-W-based Salvator-XS board DT bindings
|
|
Blink the LED on a kernel panic.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Blink the LED on a kernel panic.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Guodong Xu <guodong.xu@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Blink the LED on a kernel panic.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ARCH_S3C24XX is a very exceptional platform that some DT files in
arch/arm/boot/dts/, but does not select USE_OF.
All the other platforms with DT files correctly select USE_OF
directly or indirectly (Most of them are either ARCH_MULTIPLATFORM
or ARM_SINGLE_ARMV7M).
With ARCH_S3C24XX fixed, "ifeq ($(CONFIG_OF),y)" in DT Makefile
can be deleted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Official vendor string is now "tpo" and not "toppoly".
Requires patch "omapdrm: panel: fix compatible vendor string for td028ttec1"
so that the driver understands both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add basic panel support for the Nokia N950. It must be tweaked a
little bit later, since the panel was built into the device
upside-down. Also the first 5 and the last 5 pixels are covered
by plastic.
Signed-off-By: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This improves LCD support for the Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DMA transfer uses DVC
DMA DMApp
[MEM] -> [SRC] -> [DVC] -> [SSIU] -> [SSI]
DMA DMApp
[MEM] <- [DVC] <- [SRC] <- [SSIU] <- [SSI]
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
DMA transfer to/from SRC
DMA DMApp
[MEM] -> [SRC] -> [SSIU] -> [SSI]
DMA DMApp
[MEM] <- [SRC] <- [SSIU] <- [SSI]
Current sound driver is supporting SSI/SRC random connection.
So, this patch is trying
SSI3 -> SRC3
SSI4 <- SRC4
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
DMA transfer to/from SSIU
DMA
[MEM] -> [SSIU] -> [SSI]
DMA
[MEM] <- [SSIU] <- [SSI]
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
DMA transfer to/from SSI
DMA
[MEM] -> [SSI]
DMA
[MEM] <- [SSI]
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable sound PIO support on carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables SGTL5000 audio codec on the carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the generic r8a7745(RZ/G1E) part of the sound device node.
This patch is based on the r8a7794 sound work by Sergei Shtylyov.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Instantiate the audio DMA controller on the r8a7745 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Describe the external audio clocks required by the sound driver.
Boards that provide audio clocks need to override the clock frequencies.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
add power controller node for MT2712
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
v4.15-next/dts64
|
|
Add opp v2 information,
and also add clocks, regulators and opp information into cpu nodes
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add clock controller nodes for MT2712, include topckgen, infracfg,
pericfg, mcucfg and apmixedsys. This patch also add six oscillators that
provide clocks for MT2712.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add opp v2 information,
and also add clocks, regulators and opp information into cpu nodes
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add power dt-bindings for MT2712.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The Timer Pulse Unit has registers that lie outside the declared
register block. Enlarge the register block size to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables usb3_peri0 that uses usb3_phy0 to enable VBUS
detection for the USB3.0 peripheral.
The Salvator-X[S] has USB3.0 type-A connector and supplies VBUS
if USB3.0 host runs. So, you need a special cable for it, and
to stop the VBUS supplies from the board, after you installs
a gadget driver, you should run the following command to avoid
conflict VBUS supply:
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables usb3_phy0 node for Salvator-X[S].
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds USB3.0 PHY node for r8a7796.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds USB3.0 PHY node for r8a7795.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Fixes a warning when building with W=1.
All of the ASPEED device trees build without warnings now.
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The OpenBMC flash layout is used by Palmetto systems.
Add the unit name to the memory node to fix a warning with W=1.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
- Fix incorrect RAM size
- Remove alias; these are now specified in the dtsi
- Add newly upstreamed devices
- Include OpenBMC flash layout
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The Qanta Q71L BMC is an ASPEED ast2400 based BMC that is part of a
Qanta x86 server.
This adds the device tree description for most upstream components. It
is a squashed commit from the OpenBMC kernel tree.
Signed-off-by: Peter Hanson <peterh@google.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Rick Altherr <raltherr@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Zaius is a POWER9 platform announced at OpenPOWER Summit 2016. This adds
basic DTS support for its AST2500 BMC.
This adds the device tree description for most upstream components. It
is a squashed commit of all of the patches from the OpenBMC kernel tree.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Peter Hanson <peterh@google.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Rick Altherr <raltherr@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The Witherspoon BMC is an ASPEED ast2500 based BMC that is part of an
OpenPower Power9 server.
This adds the device tree description for most upstream components. It
is a squashed commit from the OpenBMC kernel tree.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
In preperation for adding more boards.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This is a layout used by OpenBMC systems. It describes the fixed flash
layout of a 32MB mtd device.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
In b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier
to files with no license") these files had the GPL-2.0 licence added
automatically. Update them to be GPL 2.0+ in line with other IBM kernel
contributions.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
We don't require it for any of the ASPEED systems.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
LPC snoop hardware on the ASPEED BMC, used for monitoring
host I/O port activity.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The PWM/tach unit has a clock and reset phandle. It needs both in order
to function correctly.
Signed-off-by: Joel Stanley <joel@jms.id.au>
--
v3:
Add the pwm reset phandle
|
|
This enables a feature where the driver can debounce inputs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
