| Age | Commit message (Collapse) | Author |
|---|
|
|
|
The audio DMA request for hdmi is crossbar 76 and we use sDMA
to handle the data transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently, a nlmon link inside a child namespace can observe systemwide
netlink activity. Filter the traffic so that nlmon can only sniff
netlink messages from its own netns.
Test case:
vpnns -- bash -c "ip link add nlmon0 type nlmon; \
ip link set nlmon0 up; \
tcpdump -i nlmon0 -q -w /tmp/nlmon.pcap -U" &
sudo ip xfrm state add src 10.1.1.1 dst 10.1.1.2 proto esp \
spi 0x1 mode transport \
auth sha1 0x6162633132330000000000000000000000000000 \
enc aes 0x00000000000000000000000000000000
grep --binary abc123 /tmp/nlmon.pcap
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all variants of the sh_eth hardware have Gigabit
support. Unfortunately, the current driver doesn't tell the PHY about
the limited MAC capabilities. Due to this, if you have a Gigabit
capable PHY, the PHY will advertise its Gigabit capability and
establish a link at 1Gbit/s, even though the MAC doesn't support it.
In order to avoid this, we use the recently introduced
phy_set_max_speed() to tell the PHY to not advertise speed higher than
100 MBit/s.
Tested on a SH7786 platform, with a Gigabit PHY.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The metastability workaround causes Erratic errors [1]
on the HighSpeed USB PHY which can cause upto 2 seconds
delay in enumerating to a USB host while in Gadget mode.
Disable the Run/Stop metastability workaround to avoid this
ill effect. We are aware that this opens up the opportunity
for Run/Stop metastability, however this issue has never been
observed in TI releases so we think that Run/Stop metastability
is a lesser evil than the PHY Erratic errors. So disable it.
[1] USB controller trace during gadget enumeration
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event
(00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event
(00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux/intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since U-Boot passes this information to the kernel, let's remove
the partition information from the device tree for
logicpd-torpedo-37xx-devkit and logicpd-som-lv-37xx-devkit
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Set powerhold property for tps65917
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for DM816x SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for DM814x SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for AM43xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for AM33xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for DRA7 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for OMAP5 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for OMAP4 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add simple-bus compatibility and ranges properties to prcm node. This is
done in preparation of adding the support for clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add simple-bus compatibility and ranges properties to prcm node. This is
done in preparation of adding the support for clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add simple-bus compatibility and ranges properties to prcm node. This is
done in preparation of adding the support for clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add simple-bus compatibility and ranges properties to cm1, cm2 and prm
nodes. This is done in preparation of adding the support for clkctrl
nodes.
SPLIT: timer1 fck setup
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add simple-bus compatibility and ranges properties to cm1, cm2 and prm
nodes. This is done in preparation of adding the support for clkctrl
nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add simple-bus compatibility and ranges properties to cm_core_aon, cm_core
and prm nodes. This is done in preparation of adding the support for
clkctrl nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the functional clock definition for timers1/2. This is needed so that
the clock rate claculations continue to function properly once dm816x
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the functional clock definition for timers1/2. This is needed so that
the clock rate claculations continue to function properly once dm814x
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the functional clock definition for timer1. This is needed so that
the clock rate calculations continue to function properly once dra7
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the functional clock definition for timers1/2. This is needed so that
the clock rate calculations continue to function properly once am33xx
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the functional clock definition for timers1/2. This is needed so that
the clock rate calculations continue to function properly once am33xx
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the functional clock definition for timer1. This is needed so that
the clock rate calculations continue to function properly once omap4
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the functional clock definition for timer1. This is needed so that
the clock rate calculations continue to function properly once omap5
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
Fixes: 7334b3e47aee ("net: phy: Add Meson GXL Internal PHY driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On systems with hardware dirty bit management, the ltp madvise09 unit
test fails due to dirty bit information being lost and pages being
incorrectly freed.
This was bisected to:
arm64: Ignore hardware dirty bit updates in ptep_set_wrprotect()
Reverting this commit leads to a separate problem, that the unit test
retains pages that should have been dropped due to the function
madvise_free_pte_range(.) not cleaning pte's properly.
Currently pte_mkclean only clears the software dirty bit, thus the
following code sequence can appear:
pte = pte_mkclean(pte);
if (pte_dirty(pte))
// this condition can return true with HW DBM!
This patch also adjusts pte_mkclean to set PTE_RDONLY thus effectively
clearing both the SW and HW dirty information.
In order for this to function on systems without HW DBM, we need to
also adjust pte_mkdirty to remove the read only bit from writable pte's
to avoid infinite fault loops.
Cc: <stable@vger.kernel.org>
Fixes: 64c26841b349 ("arm64: Ignore hardware dirty bit updates in ptep_set_wrprotect()")
Reported-by: Bhupinder Thakur <bhupinder.thakur@linaro.org>
Tested-by: Bhupinder Thakur <bhupinder.thakur@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The high_memory global variable is used by
cma_declare_contiguous(.) before it is defined.
We don't notice this as we compute __pa(high_memory - 1), and it looks
like we're processing a VA from the direct linear map.
This problem becomes apparent when we flip the kernel virtual address
space and the linear map is moved to the bottom of the kernel VA space.
This patch moves the initialisation of high_memory before it used.
Cc: <stable@vger.kernel.org>
Fixes: f7426b983a6a ("mm: cma: adjust address limit to avoid hitting low/high memory boundary")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
After commit 4d3a57f23dec ("netfilter: conntrack: do not enable connection
tracking unless needed") conntrack is disabled by default unless some
module explicitly declares dependency in particular network namespace.
Fixes: a357b3f80bc8 ("netfilter: nat: add dependencies on conntrack module")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add efuse node for UniPhier LD4, Pro4, sLD8, Pro5 and PXs2.
This efuse node is included in soc-glue.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Users of ptr_ring expect that it's safe to give the
data structure a pointer and have it be available
to consumers, but that actually requires an smb_wmb
or a stronger barrier.
In absence of such barriers and on architectures that reorder writes,
consumer might read an un=initialized value from an skb pointer stored
in the skb array. This was observed causing crashes.
To fix, add memory barriers. The barrier we use is a wmb, the
assumption being that producers do not need to read the value so we do
not need to order these reads.
Reported-by: George Cherian <george.cherian@cavium.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is code that probably should never have made it into the kernel in
the first place: it depends on a driver that hadn't been reviewed yet.
During the HVC_SBI_RISCV review process a better way of doing this was
suggested, but that means this code is defunct. It's compile-time
disabled in 4.15 because the driver isn't in, so I think it's safe to
just remove this for now.
CC: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
I removed this last week because of an incorrect comment:
smp_mb__after_spinlock() is actually still used, and is necessary on
RISC-V. It's been resurrected, with a comment that describes what it
actually does this time. Thanks to Andrea for finding the bug!
Fixes: 3343eb6806f3 ("RISC-V: Remove smb_mb__{before,after}_spinlock()")
CC: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
In the current code, there is a ! logical NOT where a bitwise ~ NOT was
intended. It means that we never return -EINVAL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Commit 15e85695e500 ("arm64: dts: uniphier: add GPIO hog definition")
missed to update the PXs3 DTS for some reason. Do it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The dt-bindings header was applied to the driver subsystem. I had to
wait for a merge window to use it from DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The dt-bindings header was applied to the driver subsystem. I had to
wait for a merge window to use it from DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
https://github.com/t-kristo/linux-pm into omap-for-v4.16/soc
|
|
Make these const as they are only getting passed to the functions
cm_register and cm_unregister having the arguments as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Make the pointer cm_ll_data of type cm_ll_data as const as it does not
modify the fields of the structure it points too.
After this change, make the argument of cm_register function as const as
it is used to initialise cm_ll_data or used inside an if condition.
Make the pointer argument of cm_unregister function as const as it is only
used inside an if condition.
Add const to the function prototypes too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The filw was converted from print_symbol() to %pf some time
ago (044c782ce3a901fb "workqueue: fix checkpatch issues").
kallsyms does not seem to be needed anymore.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Fix the following kernel-doc warnings after code restructuring:
../kernel/sched/core.c:5113: warning: No description found for parameter 't'
../kernel/sched/core.c:5113: warning: Excess function parameter 'interval' description in 'sched_rr_get_interval'
get rid of set_fs()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: abca5fc535a3e ("sched_rr_get_interval(): move compat to native,
Link: http://lkml.kernel.org/r/995c6ded-b32e-bbe4-d9f5-4d42d121aff1@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three fixes:
* for certificate C file generation, don't use hexdump as it's
not always installed by default, use pure posix instead (od/sed)
* for certificate C file generation, don't write the file if
anything fails, so the build abort will not cause a bad build
upon a second attempt
* fix locking in ieee80211_sta_tear_down_BA_sessions() which had
been causing lots of locking warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If something calls ioremap() with an address not aligned to PAGE_SIZE, the
returned address might be not aligned as well. This led to a probe
registered on exactly the returned address, but the entire page was armed
for mmiotracing.
On calling iounmap() the address passed to unregister_kmmio_probe() was
PAGE_SIZE aligned by the caller leading to a complete freeze of the
machine.
We should always page align addresses while (un)registerung mappings,
because the mmiotracer works on top of pages, not mappings. We still keep
track of the probes based on their real addresses and lengths though,
because the mmiotrace still needs to know what are mapped memory regions.
Also move the call to mmiotrace_iounmap() prior page aligning the address,
so that all probes are unregistered properly, otherwise the kernel ends up
failing memory allocations randomly after disabling the mmiotracer.
Tested-by: Lyude <lyude@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Acked-by: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: nouveau@lists.freedesktop.org
Link: http://lkml.kernel.org/r/20171127075139.4928-1-kherbst@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
earlyprintk=efi,keep does not work any more with a warning
in mm/early_ioremap.c: WARN_ON(system_state != SYSTEM_BOOTING):
Boot just hangs because of the earlyprintk within the earlyprintk
implementation code itself.
This is caused by a new introduced middle state in:
69a78ff226fe ("init: Introduce SYSTEM_SCHEDULING state")
early_ioremap() is fine in both SYSTEM_BOOTING and SYSTEM_SCHEDULING
states, original condition should be updated accordingly.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: bp@suse.de
Cc: linux-efi@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20171209041610.GA3249@dhcp-128-65.nay.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch fixes ipmi crash on parisc introduced in the kernel 4.15-rc.
The pointer io.io_setup is not initialized and thus it causes crash in
try_smi_init when attempting to call new_smi->io.io_setup.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
When the IPMI PCI code was split out, some code was consolidated for
setting the io_setup field in the io structure. The PCI code needed
this set before registration to probe register spacing, though, so
restore the old code for that function.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197999
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Meelis Roos <mroos@linux.ee>
|
