| Age | Commit message (Collapse) | Author |
|---|
|
Add serial port aliases for consoles > 6.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.
For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page
Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6
Just add basic support for the moment, the following updates are needed:
i) Ethernet - depends on SoC dts fixes
ii) USB Client (USB2) - depends on GPIO extcon
ii) HDMI - additional driver fixes pending
iii) Audio - additional driver fixes pending
NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can't suppose that the i2c2 pins are configured as I2C bus, these pins are
connected to expansion connectors.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the omap3-igep0020-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEPv2 hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for the new hardware revision of the IGEP COM MODULE. Basically,
the new revision G replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the omap3-igep0030-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEP COM MODULE hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
New IGEP boards revisions will use another Wifi module, so this patch moves
the DT nodes outside the common omap3-igep.dtsi file to specific DT for every
board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
At this moment all supported boards use same NAND chip, so has more sense
move the GPMC and NAND configuration to the omap3-igep.dtsi common place.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
UART2 is used to connect the processor with the bluetooth chip, these pins
are not common between IGEPv2 boards and IGEP COM MODULE boards. This patch
muxes the correct pins for every board and removes UART2 configuration from
common omap3-igep.dtsi file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pcibios_msi_controller() to get the msi_controller associated with a
PCI device. This is to allow arches to store the msi_controller in the
arch-specific PCI sysdata.
[bhelgaas: changelog, take pci_dev instead of pci_bus]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
"msi_chip" isn't very descriptive, so rename it to "msi_controller". That
tells a little more about what it does and is already used in device tree
bindings.
No functional change.
[bhelgaas: changelog, change *only* the struct name so it's reviewable]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
New Fam15h models carry extra feature bits and extend
the MSR register space for IBS ops. Adding them here.
While at it, add functionality to read IbsBrTarget and
OpData4 depending on their availability if user wants a
PERF_SAMPLE_RAW.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <paulus@samba.org>
Cc: <acme@kernel.org>
Link: http://lkml.kernel.org/r/1415651066-13523-1-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
On the LeMaker Banana Pi, probing the external ethernet PHY connected
to the SoC's internal GMAC module sometimes fails. The PHY power
supply is handled via a GPIO-controlled regulator, and the existing
regulator startup-delay of 50000us is too short to make sure that the
PHY is always fully powered up when it is queried by phylib. Tests
have shown that to provide a reliable PHY detection, the startup-delay
has to be increased to at least 60000us. To have a certain safety margin
and to cater for manufacturing variations between different boards,
the delay gets set to 100000us as discussed on the linux-arm-kernel
mailinglist.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The existing xtables matches and targets, when used from nft_compat, may
sleep from the destroy path, ie. when removing rules. Since the objects
are released via call_rcu from softirq context, this results in lockdep
splats and possible lockups that may be hard to reproduce.
Patrick also indicated that delayed object release via call_rcu can
cause us problems in the ordering of event notifications when anonymous
sets are in place.
So, this patch restores the synchronous object release from the commit
and abort paths. This includes a call to synchronize_rcu() to make sure
that no packets are walking on the objects that are going to be
released. This is slowier though, but it's simple and it resolves the
aforementioned problems.
This is a partial revert of c7c32e7 ("netfilter: nf_tables: defer all
object release via rcu") that was introduced in 3.16 to speed up
interaction with userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Instead of the match->name, which is of course not relevant.
Fixes: f3f5dde ("netfilter: nft_compat: validate chain type in match/target")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Check for nat chain dependency only, which is the one that can
actually crash the kernel. Don't care if mangle, filter and security
specific match and targets are used out of their scope, they are
harmless.
This restores iptables-compat with mangle specific match/target when
used out of the OUTPUT chain, that are actually emulated through filter
chains, which broke when performing strict validation.
Fixes: f3f5dde ("netfilter: nft_compat: validate chain type in match/target")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Instead of init_net when using xtables over nftables compat.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We should be returning an error code here instead of success. Either
-ENODEV or -ENOMEM would work. There is also a failure message in
printk().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The bnx2fc_if_create() function returns NULL on failure, it never
returns an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
At least LID reassignment can trigger a race condition in the SRP
initiator driver, namely the receive completion handler trying to
post a request on a QP during or after QP destruction and before
the CQ's have been destroyed. Avoid this race by modifying a QP
into the error state and by waiting until all receive completions
have been processed before destroying a QP.
Reported-by: Max Gurtuvoy <maxg@mellanox.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Improve performance by using multiple RDMA/RC channels per SCSI
host for communication with an SRP target. About the
implementation:
- Introduce a loop over all channels in the code that uses
target->ch.
- Set the SRP_MULTICHAN_MULTI flag during login for the creation
of the second and subsequent channels.
- RDMA completion vectors are chosen such that RDMA completion
interrupts are handled by the CPU socket that submitted the I/O
request. As one can see in this patch it has been assumed if a
system contains n CPU sockets and m RDMA completion vectors
have been assigned to an RDMA HCA that IRQ affinity has been
configured such that completion vectors [i*m/n..(i+1)*m/n) are
bound to CPU socket i with 0 <= i < n.
- Modify srp_free_ch_ib() and srp_free_req_data() such that it
becomes safe to invoke these functions after the corresponding
allocation function failed.
- Add a ch_count sysfs attribute per target port.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Since the block layer already contains functionality to assign
a tag to each request, use that functionality instead of
reimplementing that functionality in the SRP initiator driver.
This change makes the free_reqs list superfluous. Hence remove
that list.
[hch: updated to use .use_blk_tags instead scsi_activate_tcq]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This will fix no sound in Linux system after reboot from windows.
Change log:
- alc662_fill_coef() is replaced with alc_fill_eapd_coef_idx()
and move into alc_auto_init_amp().
- For ALC262, ALC267, ALC268, ALC269, ALC233, ALC255, ALC280, ALC282,
ALC283, ALC284, ALC285, ALC286, ALC288, ALC290, ALC292, ALC293, ALC294,
ALC668, ALC888VC, ALC888VD, ALC891, ALC892, ALC898 and ALC1150, add update
COEF control for EAPD setting.
- Remove alc269_fill_coef() for update EAPD control line.
ADDITIONAL NOTE:
Many Realtek cdoecs have a COEF bit to switch the master amp control
between COEF and EAPD. Windows drivers seem using COEF while we use
EAPD, which is more standard. As a result, some system suffer from
the silent output when booting after Windows. This patch sets the
COEF bits on the relevant codecs properly to switch to EAPD control.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87771
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Changes in this patch:
- Move channel variables into a new structure (struct srp_rdma_ch).
- Add an srp_target_port pointer, 'lock' and 'comp_vector' members
in struct srp_rdma_ch.
- Add code to initialize these three new member variables.
- Many boring "target->" into "ch->" changes.
- The cm_id and completion handler context pointers are now of type
srp_rdma_ch * instead of srp_target_port *.
- Three kzalloc(a * b, f) calls have been changed into kcalloc(a, b, f)
to avoid that this patch would trigger a checkpatch warning.
- Two casts from u64 into unsigned long long have been left out
because these are superfluous. Since considerable time u64 is
defined as unsigned long long for all architectures supported by
the Linux kernel.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Introduce the srp_target_port member variables 'sgid' and 'pkey'.
Change the type of 'orig_dgid' from __be16[8] into union ib_gid.
This patch does not change any functionality but makes the
"Separate target and channel variables" patch easier to verify.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If a cable is pulled during LUN scanning it can happen that the
SRP rport and the SCSI host have been created but no LUNs have been
added to the SCSI host. Since multipathd only sends SCSI commands
to a SCSI target if one or more SCSI devices are present and since
there is no keepalive mechanism for IB queue pairs this means that
after a LUN scan failed and after a reconnect has succeeded no
data will be sent over the QP and hence that a subsequent cable
pull will not be detected. Avoid this by not creating an rport or
SCSI host if a cable is pulled during a SCSI LUN scan.
Note: so far the above behavior has only been observed with the
kernel module parameter ch_count set to a value >= 2.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Attempting to connect three times may be insufficient after an
initiator system tries to relogin, especially if the relogin
attempt occurs before the SRP target service ID has been
registered. Since the srp_daemon retries a failed login attempt
anyway, remove the stale connection retry mechanism.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The patch that adds multichannel support into the SRP initiator
driver introduces an additional call to srp_free_ch_ib(). This
patch helps to keep that later patch simple.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Remove 2 redundant extern inline functions: qla8044_set_qsnt_ready() and
qla8044_need_reset_handler(). At present, within upstream next kernel
source code, they are only used within "drivers/scsi/qla2xxx/qla_nx2.c".
The related error and warnings (with allmodconfig under tile):
CC [M] drivers/scsi/qla2xxx/qla_nx2.o
drivers/scsi/qla2xxx/qla_nx2.c:1633:1: error: static declaration of 'qla8044_need_reset_handler' follows non-static declaration
qla8044_need_reset_handler(struct scsi_qla_host *vha)
^
In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
from drivers/scsi/qla2xxx/qla_nx2.c:11:
drivers/scsi/qla2xxx/qla_gbl.h:756:20: note: previous declaration of 'qla8044_need_reset_handler' was here
extern inline void qla8044_need_reset_handler(struct scsi_qla_host *vha);
^
drivers/scsi/qla2xxx/qla_gbl.h:756:20: warning: inline function 'qla8044_need_reset_handler' declared but never defined
make[3]: *** [drivers/scsi/qla2xxx/qla_nx2.o] Error 1
make[2]: *** [drivers/scsi/qla2xxx] Error 2
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2
CC [M] drivers/scsi/qla2xxx/qla_tmpl.o
In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
from drivers/scsi/qla2xxx/qla_tmpl.c:7:
drivers/scsi/qla2xxx/qla_gbl.h:755:20: warning: inline function 'qla8044_set_qsnt_ready' declared but never defined
extern inline void qla8044_set_qsnt_ready(struct scsi_qla_host *vha);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Use dma_set_mask_and_coherent() to set both the DMA and coherent
DMA mask.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Even though the ipr driver is only used on PCI, convert it
to use the generic DMA API.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The request (and SCSI command) tag is the tag number assigned
by the generic block-tagging code, not the SCSI-II tag messages.
Those are represented by the device flags 'tagged_supported',
'simple_tags', and 'ordered_tags'.
(The SCSI midlayer doesn't use HEAD_OF_QUEUE tags).
So fixup vmw_pvscsi to assign the correct tag type.
[hch: fixed up to never set MSG_ORDERED_TAG]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Arvind Kumar <arvindkumar@vmware.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This macro is only used in the NCR5380 drivers and they don't include
this header.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
ufs never looks at the tag type, so there is no need to set it either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Now that we also get proper values in cmd->request->tag for untagged
commands, there is no need to force tagged_supported to on in drivers
that need host-wide tags.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This function shouldn't change the queue type, just the depth.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Unless we want to build a SPI tag message we should just check SCMD_TAGGED
instead of reverse engineering a tag type through the use of
scsi_populate_tag_msg.
Also rename the function to spi_populate_tag_msg, make it behave like the
other spi message helpers, and move it to the spi transport class.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Remove the ordered_tags field, we haven't been issuing ordered tags based
on it since the big barrier rework in 2010.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently scsi piggy backs on the block layer to define the concept
of a tagged command. But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them. Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.
We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.
Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Move all code to set up and tear down sdev->scsi_dh_data to common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
