| Age | Commit message (Collapse) | Author |
|---|
|
This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.
Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are needed by Thunderbolt services so move them to thunderbolt.h
to make sure they are available outside of drivers/thunderbolt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These will be needed by Thunderbolt services when sending and receiving
XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP
value to be decimal in order to be consistent with other members.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thunderbolt XDomain discovery protocol uses directories which contain
properties and other directories to exchange information about what
capabilities the remote host supports. This also includes identification
information like device ID and name.
This adds support for parsing and formatting these properties and
establishes an API drivers can use in addition to the core Thunderbolt
driver. This API is exposed in a new header: include/linux/thunderbolt.h.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These messages are all 32-bit aligned and they should be packed without
the __packed attribute just fine. It also allows compiler to generate
better code on some architectures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will be using these when communicating XDomain discovery protocol
over Thunderbolt link but they might be useful for other drivers as
well.
Make them available through byteorder/generic.h.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
mlxsw: Fixlets
Couple of small nit fixes from Petr
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
mlxsw: Fixes in GRE offloading
Petr says:
This patchset fixes a couple unrelated problems in offloading IP-in-IP tunnels
in mlxsw driver.
- The first patch fixes a potential reference-counting problem that might lead
to a kernel crash.
- The second patch associates IPIP next hops with their loopback RIFs. Besides
being the right thing to do, it also fixes a problem where offloaded IPv6
routes that forward to IP-in-IP netdevices were not flagged as such.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When considering whether to set RTNH_F_OFFLOAD flag on an IPv6 route,
mlxsw_sp_fib6_entry_offload_set() looks up the mlxsw_sp_nexthop
corresponding to a given route, and decides based on whether the next
hop's offloaded flag was set. When looking for the matching next hop, it
also takes into account the device of the route, which must match next
hop's RIF.
IPIP next hops however hitherto didn't set the RIF. As a result, IPv6
routes forwarding traffic to IP-in-IP netdevices are never marked as
offloaded, even when they actually are.
Thus track RIF of IPIP next hops the same way as that of ETHERNET next
hops.
Fixes: 8f28a3097645 ("mlxsw: spectrum_router: Support IPv6 overlay encap")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating a new RIF, bumping RIF count of the containing VR is the
last thing to be done. Symmetrically, when destroying a RIF, RIF count
is first dropped and only then the rest of the cleanup proceeds.
That's a problem for loopback RIFs. Those hold two VR references: one
for overlay and one for underlay. mlxsw_sp_rif_destroy() releases the
overlay one, and the deconfigure() callback the underlay one. But if
both overlay and underlay are the same, and if there are no other
artifacts holding the VR alive, this put actually destroys the VR. Later
on, when mlxsw_sp_rif_destroy() calls mlxsw_sp_vr_put() for the same VR,
the VR will already have been released and the kernel crashes with NULL
pointer dereference.
The underlying problem is that the RIF under destruction ends up
referencing the overlay VR much longer than it claims: all the way until
the call to mlxsw_sp_vr_put(). So line up the reference counting
properly to reflect this. Make corresponding changes in
mlxsw_sp_rif_create() as well for symmetry.
Fixes: 6ddb7426a7d4 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fou test lifted from ip-fou man page.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Horman says:
====================
flow_dissector: dissect tunnel info
Move dissection of tunnel info from the flower classifier to the flow
dissector where all other dissection occurs. This should not have any
behavioural affect on other users of the flow dissector.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move dissection of tunnel info from the flower classifier to the flow
dissector where all other dissection occurs. This should not have any
behavioural affect on other users of the flow dissector.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the skb parameter of skb_metadata_dst() and skb_tunnel_info()
const as they are not modified. This is in preparation for using
them in call-sites where skb is const.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The usx2y driver allocates the stream read/write buffers in continuous
pages depending on the stream setup, and this may spew the kernel
warning messages with a stack trace like:
WARNING: CPU: 1 PID: 1846 at mm/page_alloc.c:3883
__alloc_pages_slowpath+0x1ef2/0x2d70
Modules linked in:
CPU: 1 PID: 1846 Comm: kworker/1:2 Not tainted
....
It may confuse user as if it were any serious error, although this is
no fatal error and the driver handles the error case gracefully.
Since the driver has already some sanity check of the given size (128
and 256 pages), it can't pass any crazy value. So it's merely page
fragmentation.
This patch adds __GFP_NOWARN to each caller for suppressing such
kernel warnings. The original issue was spotted by syzkaller.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Although very unlikely, it is possible that cancel_work_sync() may stop
the service_task before it actually started. In this case, the
__FM10K_SERVICE_SCHED bit will never be cleared. This results in the
service task being unable to reschedule in the future. Add a helper
function which sets the service disable bit, waits for the service task
to stop and clears the schedule bit, thus avoiding the race condition.
We know the schedule bit is safe to clear because the cancel_work_sync()
guarantees the service task is not running.
Add a helper function also to restart the service task, for symmetry.
This is not strictly needed but helps the mental model of how to stop
and start the service task.
This race could only happen in fm10k_suspend/fm10k_resume as this is the
only place where the service task is actually restarted. Thus,
suspend/resume testing would be ideal. However, note that the chance of
this happening is very slim as the service event is scheduled for
immediate execution, and you would have to trigger a suspend at almost
the exact same time as the service task was scheduled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A future patch needs these functions defined earlier in the file. Move
them closer to above where they will be called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It is possible that under rare circumstances the device is undergoing
a reset, such as when a PFLR occurs, and the device may be transmitting
simultaneously. In this case, we might attempt to divide by zero when
finding the proper r_idx. Instead, lets read the num_tx_queues once,
and make sure it's non-zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We've always had a really weird looping construction for resetting VFs.
We read the VFLRE register and reset the VF if the corresponding bit is
set, which makes sense. However we loop continuously until we no longer
have any bits left unset. At first this makes sense, as a sort of "keep
trying until we succeed" concept.
Unfortunately this causes a problem if we happen to surprise remove
while this code is executing, because in this case we'll always read all
1s for the VFLRE register. This results in a hard lockup on the CPU
because the loop will never terminate.
Because our own reset function will clear the VFLR event register
always, (except when we've lost PCIe link obviously) there is no real
reason to loop. In practice, we'll loop over once and find that no VFs
are pending anymore.
Lets just check once. Since we're clear the notification when we reset
there's no benefit to the loop. Additionally, there shouldn't be a race
as future VLFRE events should trigger an interrupt. Additionally, we
didn't warn or do anything in the looped case anyways.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We're doing a really convoluted bitshift and read for the PFVFLRE
register. Just reading the PFVFLRE(1), shifting it by 32, then reading
PFVFLRE(0) should be sufficient.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we load the driver, we set the last_reset to be in the future,
which delays the initial driver reset. Additionally, the service task
isn't scheduled to run automatically until the timer runs out. This
causes a needless delay of the first reset to begin talking to the
switch manager.
We can avoid this by simply not setting last_reset and immediately
scheduling the service task while in probe. This allows the device to
wake up faster, and avoids this delay.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Newer versions of GCC starting with 7 now additionally warn when a case
statement may fall through without an explicit comment mentioning it.
Add such a comment to silence the warning, as this is expected.
Unfortunately the comment must come directly before the next case
statement, so we put it outside the #ifdef. Otherwise, the compiler
cannot properly detect it and thus the warning is displayed regardless.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
New versions of GCC since version 7 began warning about possible
truncation of calls to snprintf. We can fix this and avoid false
positives. First, we should pass the full buffer size to snprintf,
because it guarantees a NULL character as part of its passed length, so
passing len-1 is simply wasting a byte of possible storage.
Second, if we make the ri and ti variables unsigned, the compiler is
able to correctly reason that the value never gets larger than 256, so
it doesn't need to warn about the full space required to print a signed
integer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Newer versions of GCC since version 7 now warn when a case statement may
fall through without an explicit comment. "Fallthough" does not count as
it is misspelled. Fix the typos for these comments to appease the new
warnings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In fm10k_get_host_state_generic, we check the mailbox tx_read() function
to ensure that the mailbox is still open. This function also checks to
make sure we have space to transmit another message. Unfortunately, if
we just recently sent a bunch of messages (such as enabling hundreds of
VLANs on a VF) this can result in a race where the watchdog task thinks
the link went down just because we haven't had time to process all these
messages yet.
Instead, lets just check whether the mailbox is still open. This ensures
that we don't race with the Tx FIFO, and we only link down once the
mailbox is not open.
This is safe, because if the FIFO fills up and we're unable to send
a message for too long, we'll end up triggering the timeout detection
which results in a reset. Additionally, since we still check to ensure
the mailbox state is OPEN, we'll transition to link down whenever the
mailbox closes as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Two single characters should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we are handling PF<->VF mailbox messages, it is possible that the
VF will send us so many messages that the PF<->SM FIFO will fill up. In
this case, we stop the loop and wait until the service event is
rescheduled.
Normally this should happen due to an interrupt. But it is possible that
we don't get another interrupt for a while and it isn't until the
service timer actually reschedules us. Instead, simply reschedule
immediately which will cause the service event to be run again as soon
as we exit.
This ensures that we promptly handle all of the PF<->VF messages with
minimal delay, while still giving time for the SM mailbox to drain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we process VF mailboxes, the driver is likely going to also queue
up messages to the switch manager. This process merely queues up the
FIFO, but doesn't actually begin the transmission process. Because we
hold the mailbox lock during this VF processing, the PF<->SM mailbox is
not getting processed at this time. Ensure that we actually process the
PF<->SM mailbox in between each PF<->VF mailbox.
This should ensure prompt transmission of the messages queued up after
each VF message is received and handled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
previous commit 5d37ca14 "ceph: send LSSNAP request to auth mds
of directory inode" is buggy. It makes __choose_mds() choose mds
base on hash of '.snap' dentry.
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
commit 3ae0bebc "ceph: queue cap snap only when snap realm's
context changes" introduced a regression: we may not call
queue_realm_cap_snaps() for newly created snap realm. This
regression allows unflushed snapshot data to be overwritten.
Link: http://tracker.ceph.com/issues/21483
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Currently data_abort_decode() dumps the ISS field as a decimal value
with a '0x' prefix, which is somewhat misleading.
Fix it to print as hexadecimal, as was intended.
Fixes: 1f9b8936f36f4a8e ("arm64: Decode information from ESR upon mem faults")
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
members and total number of members"
This reverts commit 275353bb684e to fix a regression which can abort
'alsactl' program in alsa-utils due to assertion in alsa-lib.
alsactl: control.c:2513: snd_ctl_elem_value_get_integer: Assertion `idx < sizeof(obj->value.integer.value) / sizeof(obj->value.integer.value[0])' failed.
alsactl: control.c:2976: snd_ctl_elem_value_get_integer: Assertion `idx < ARRAY_SIZE(obj->value.integer.value)' failed.
This commit is a band-aid. In a point of usage of ALSA control interface,
the drivers still bring an issue that they prevent userspace applications
to have a consistent way to parse each levels of the dimension information
via ALSA control interface.
Let me investigate this issue. Current implementation of the drivers
have three control element sets with dimension information:
* 'Monitor Mixer Volume' (type: integer)
* 'VMixer Volume' (type: integer)
* 'VU-meters' (type: boolean)
Although the number of elements named as 'Monitor Mixer Volume' differs
depending on drivers in this group, it can be calculated by macros
defined by each driver (= (BX_NUM - BX_ANALOG_IN) * BX_ANALOG_IN). Each
of the elements has one member for value and has dimension information
with 2 levels (= BX_ANALOG_IN * (BX_NUM - BX_ANALOG_IN)). For these
elements, userspace applications are expected to handle the dimension
information so that all of the elements construct a matrix where the
number of rows and columns are represented by the dimension information.
The same way is applied to elements named as 'VMixer Volume'. The number
of these elements can also be calculated by macros defined by each
drivers (= PX_ANALOG_IN * BX_ANALOG_IN). Each of the element has one
member for value and has dimension information with 2 levels
(= BX_ANALOG_IN * PX_ANALOG_IN). All of the elements construct a matrix
with the dimension information.
An element named as 'VU-meters' gets a different way in a point of
dimension information. The element includes 96 members for value. The
element has dimension information with 3 levels (= 3 or 2 * 16 * 2). For
this element, userspace applications are expected to handle the dimension
information so that all of the members for value construct a matrix
where the number of rows and columns are represented by the dimension
information. This is different from the way for the former.
As a summary, the drivers were not designed to produce a consistent way to
parse the dimension information. This makes it hard for general userspace
applications such as amixer to parse the information by a consistent way,
and actually no userspace applications except for 'echomixer' utilize the
dimension information. Additionally, no drivers excluding this group use
the information.
The reverted commit was written based on the latter way. A commit
860c1994a70a ('ALSA: control: add dimension validator for userspace
elements') is written based on the latter way, too. The patch should be
reconsider too in the same time to re-define a consistent way to parse the
dimension information.
Reported-by: Mark Hills <mark@xwax.org>
Reported-by: S. Christian Collins <s.chriscollins@gmail.com>
Fixes: 275353bb684e ('ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members')
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add an event that indicates that a connection is authorized
(i.e. the 4 way handshake was performed by the driver). This event
should be sent by the driver after sending a connect/roamed event.
This is useful for networks that require 802.1X authentication.
In cases that the driver supports 4 way handshake offload, but the
802.1X authentication is managed by user space, the driver needs to
inform user space right after the 802.11 association was completed
so user space can initialize its 802.1X state machine etc.
However, it is also possible that the AP will choose to skip the
802.1X authentication (e.g. when PMKSA caching is used) and proceed
with the 4 way handshake immediately. In this case the driver needs
to inform user space that 802.1X authentication is no longer required
(e.g. to prevent user space from disconnecting since it did not get
any EAPOLs from the AP).
This is also useful for roaming, in which case it is possible that
the driver used the Fast Transition protocol so 802.1X is not
required.
Since there will now be a dedicated notification indicating that the
connection is authorized, the authorized flag can be removed from the
roamed event. Drivers can send the new port authorized event right
after sending the roamed event to indicate the new AP is already
authorized. This therefore reserves the old PORT_AUTHORIZED attribute.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add Transmit Power Control OUI type definition for WLAN_OUI_MICROSOFT.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Patch fixes htmldocs build problem:
Error(.//net/mac80211/sta_info.h:416): cannot understand prototype: 'STA_SLOW_THRESHOLD 6000 '
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Section 11.23.1 of 80211-2016 specification allows TDLS peers
to operate on wider bandwidths though they are connected to a BSS
which do not support wider bandwidth operations, provided both the
peers advertise wider bandwidth capabilities.
The existing logic considers the minimum of station's and AP's
capability for bandwidth computation. The same logic applies for
TDLS peers as well, this restricts operating on wider bandwidths
over a TDLS link when the peers are connected to legacy APs.
As an example, if 80Mhz VHT capable peers are connected to a 20Mhz
5 GHz AP, then as per the existing logic TDLS operation will be
restricted to 20Mhz.
Address this problem by not considering BSS capability in bandwidth
computation if the participating TDLS peers have wider bandwidth
capability.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
[lots of wording/typo fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This reverts commit fcaa4a07d2a4b541e91da7a55d8b3331f96d1865.
As noted by Masaki [1], 0x120A + trackpoint will not be used in mass
production machines, so remove the ID accordingly.
[1] http://www.spinics.net/lists/linux-input/msg53222.html
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We should not try to bring HID device out of full power state before
calling hid_hw_close(), so that transport driver operates on powered up
device (making this inverse of the opening sequence).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The wacom_get_hdev_data function is used to find and return a reference to
the "other half" of a Wacom device (i.e., the touch device associated with
a pen, or vice-versa). To ensure these references are properly accounted
for, the function is supposed to automatically increment the refcount before
returning. This was not done, however, for devices which have pen & touch
on different interfaces of the same USB device. This can lead to a WARNING
("refcount_t: underflow; use-after-free") when removing the module or device
as we call kref_put() more times than kref_get(). Triggering an "actual" use-
after-free would be difficult since both devices will disappear nearly-
simultaneously. To silence this warning and prevent the potential error, we
need to increment the refcount for all cases within wacom_get_hdev_data.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The driver strength selection is missed and required when selecting
hs400es. So, It is added here.
Fixes: 81ac2af65793ecf ("mmc: core: implement enhanced strobe support")
Cc: stable@vger.kernel.org
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make local functions static to fix
HOSTCC samples/bpf/xdp_monitor_user.o
samples/bpf/xdp_monitor_user.c:64:7: warning: no previous prototype for ‘gettime’ [-Wmissing-prototypes]
__u64 gettime(void)
^~~~~~~
samples/bpf/xdp_monitor_user.c:209:6: warning: no previous prototype for ‘print_bpf_prog_info’ [-Wmissing-prototypes]
void print_bpf_prog_info(void)
^~~~~~~~~~~~~~~~~~~
Fixes: 3ffab5460264 ("samples/bpf: xdp_monitor tool based on tracepoints")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the unlikely event that mfc->mfc_un.res.ttls[i] is 255 for all
values of i from 0 to MAXIVS-1, the err is not set at all and hence
has a garbage value on the error return at the end of the function,
so initialize it to 0. Also, the error return check on err and goto
to err: inside the for loop makes it impossible for err to be zero
at the end of the for loop, so we can remove the redundant err check
at the end of the loop.
Detected by CoverityScan CID#1457207 ("Unitialized scalar value")
Fixes: c011ec1bbfd6 ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jonas Gorski says:
====================
bcm63xx_enet: small fixes and cleanups
This patch set fixes a few theoretical issues and cleans up the code a
bit. It also adds a bit more managed function usage to simplify clock
and iomem usage.
Based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't use anyhing from that file, so drop it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_disable and clk_unprepare are NULL-safe, so need to duplicate the
NULL check of the functions.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use managed functions where possible to reduce the amount of resource
handling on error and remove paths.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
