| Age | Commit message (Collapse) | Author |
|---|
|
Using a kernel with the Undefined Behaviour Sanity Checker (UBSAN) enabled, the
following array overrun is logged:
================================================================================
UBSAN: array-index-out-of-bounds in /home/finger/wireless-drivers-next/drivers/net/wireless/realtek/rtw88/phy.c:1789:34
index 5 is out of range for type 'u8 [5]'
CPU: 2 PID: 84 Comm: kworker/u16:3 Tainted: G O 5.12.0-rc5-00086-gd88bba47038e-dirty #651
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.50 09/29/2014
Workqueue: phy0 ieee80211_scan_work [mac80211]
Call Trace:
dump_stack+0x64/0x7c
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold+0x43/0x48
rtw_get_tx_power_params+0x83a/drivers/net/wireless/realtek/rtw88/0xad0 [rtw_core]
? rtw_pci_read16+0x20/0x20 [rtw_pci]
? check_hw_ready+0x50/0x90 [rtw_core]
rtw_phy_get_tx_power_index+0x4d/0xd0 [rtw_core]
rtw_phy_set_tx_power_level+0xee/0x1b0 [rtw_core]
rtw_set_channel+0xab/0x110 [rtw_core]
rtw_ops_config+0x87/0xc0 [rtw_core]
ieee80211_hw_config+0x9d/0x130 [mac80211]
ieee80211_scan_state_set_channel+0x81/0x170 [mac80211]
ieee80211_scan_work+0x19f/0x2a0 [mac80211]
process_one_work+0x1dd/0x3a0
worker_thread+0x49/0x330
? rescuer_thread+0x3a0/0x3a0
kthread+0x134/0x150
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x22/0x30
================================================================================
The statement where an array is being overrun is shown in the following snippet:
if (rate <= DESC_RATE11M)
tx_power = pwr_idx_2g->cck_base[group];
else
====> tx_power = pwr_idx_2g->bw40_base[group];
The associated arrays are defined in main.h as follows:
struct rtw_2g_txpwr_idx {
u8 cck_base[6];
u8 bw40_base[5];
struct rtw_2g_1s_pwr_idx_diff ht_1s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_2s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_3s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_4s_diff;
};
The problem arises because the value of group is 5 for channel 14. The trivial
increase in the dimension of bw40_base fails as this struct must match the layout of
efuse. The fix is to add the rate as an argument to rtw_get_channel_group() and set
the group for channel 14 to 4 if rate <= DESC_RATE11M.
This patch fixes commit fa6dfe6bff24 ("rtw88: resolve order of tx power setting routines")
Fixes: fa6dfe6bff24 ("rtw88: resolve order of tx power setting routines")
Reported-by: Богдан Пилипенко <bogdan.pylypenko107@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210401192717.28927-1-Larry.Finger@lwfinger.net
|
|
struct wilc is declared twice. One has been declared
at 352nd line. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210331023557.2804128-3-wanjiabing@vivo.com
|
|
struct brcmf_bus is declared twice. One has been declared
at 37th line. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210331023557.2804128-2-wanjiabing@vivo.com
|
|
Signed-off-by: Eric Lin <dslin1010@gmail.com>
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210331010418.1632816-2-dslin1010@gmail.com
|
|
The rsi_resume() does access the bus to enable interrupts on the RSI
SDIO WiFi card, however when calling sdio_claim_host() in the resume
path, it is possible the bus is already claimed and sdio_claim_host()
spins indefinitelly. Enable the SDIO card interrupts in resume_noirq
instead to prevent anything else from claiming the SDIO bus first.
Fixes: 20db07332736 ("rsi: sdio suspend and resume support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210327235932.175896-1-marex@denx.de
|
|
Since firmware can't have proper statistics, driver update the statistics
periodically to firmware to assist in tuning performance.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210326092147.30252-1-pkshih@realtek.com
|
|
struct lbs_private has been declared at 22nd line.
Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210325064154.854245-1-wanjiabing@vivo.com
|
|
s/revsion/revision/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323043657.1466296-1-unixbhaskar@gmail.com
|
|
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
There are some files in drivers/net/wireless/rsi which follow this syntax
in their file headers, i.e. start with '/**' like comments, which causes
unexpected warnings from kernel-doc.
E.g., running scripts/kernel-doc -none on drivers/net/wireless/rsi/rsi_coex.h
causes this warning:
"warning: wrong kernel-doc identifier on line:
* Copyright (c) 2018 Redpine Signals Inc."
Similarly for other files too.
Provide a simple fix by replacing such occurrences with general comment
format, i.e., "/*", to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210315173259.8757-1-yashsri421@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fixes: the libsas fix is for a problem that occurs when trying to
change the cache type of an ATA device and the libiscsi one is a
regression fix from this merge window"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: Reset num_scatter if libata marks qc as NODATA
scsi: iscsi: Fix iSCSI cls conn state
|
|
Pull vmwgfx fixes from Dave Airlie:
"This contains two regression fixes for vmwgfx, one due to a refactor
which meant locks were being used before initialisation, and the other
in fixing up some warnings from the core when destroying pinned
buffers.
vmwgfx:
- fixed unpinning before destruction
- lockdep init reordering"
* tag 'drm-fixes-2021-04-18' of git://anongit.freedesktop.org/drm/drm:
drm/vmwgfx: Make sure bo's are unpinned before putting them back
drm/vmwgfx: Fix the lockdep breakage
drm/vmwgfx: Make sure we unpin no longer needed buffers
|
|
Move restriction checks of __io_uring_register() before quiesce, saves
from waiting for requests in fail case and simplifies the code a bit.
Also add array_index_nospec() for safety
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/88d7913c9280ee848fdb7b584eea37a465391cee.1618488258.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Colin reported before possible overflow and sign extension problems in
io_provide_buffers_prep(). As Linus pointed out previous attempt did nothing
useful, see d81269fecb8ce ("io_uring: fix provide_buffers sign extension").
Do that with help of check_<op>_overflow helpers. And fix struct
io_provide_buf::len type, as it doesn't make much sense to keep it
signed.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: efe68c1ca8f49 ("io_uring: validate the full range of provided buffers for access")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/46538827e70fce5f6cdb50897cff4cacc490f380.1618488258.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Don't fail submission attempts if there are CQEs in the overflow
backlog, but give away the decision making to the userspace. It
might be very inconvenient to the userspace, especially if
submission and completion are done by different threads.
We can remove it because of recent changes, where requests
are now not locked by the backlog, backlog entries are allocated
separately, so they take less space and cgroup accounted.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
into drm-fixes
vmwgfx fixes for regressions in 5.12
Here's a set of 3 patches fixing ugly regressions
in the vmwgfx driver. We broke lock initialization
code and ended up using spinlocks before initialization
breaking lockdep.
Also there was a bit of a fallout from drm changes
which made the core validate that unreferenced buffers
have been unpinned. vmwgfx pinning code predates a lot
of the core drm and wasn't written to account for those
semantics. Fortunately changes required to fix it
are not too intrusive.
The changes have been validated by our internal ci.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f7add0a2-162e-3bd2-b1be-344a94f2acbf@vmware.com
|
|
Currently, if the user changes the pause settings, the default settings
will be restored after an interface down/up cycle, and also when
resuming from suspend. This doesn't seem to provide the best user
experience. Change this to keep user settings, and just ensure that in
jumbo mode pause is disabled.
Small drawback: When switching back mtu from jumbo to non-jumbo then
pause remains disabled (but user can enable it using ethtool).
I think that's a not too common scenario and acceptable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"One more driver bugfix for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mv64xxx: Fix random system lock caused by runtime PM
|
|
This does the directory entry name verification for the legacy
"fillonedir" (and compat) interface that goes all the way back to the
dark ages before we had a proper dirent, and the readdir() system call
returned just a single entry at a time.
Nobody should use this interface unless you still have binaries from
1991, but let's do it right.
This came up during discussions about unsafe_copy_to_user() and proper
checking of all the inputs to it, as the networking layer is looking to
use it in a few new places. So let's make sure the _old_ users do it
all right and proper, before we add new ones.
See also commit 8a23eb804ca4 ("Make filldir[64]() verify the directory
entry filename is valid") which did the proper modern interfaces that
people actually use. It had a note:
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
which this now corrects. Note that we really don't care about POSIX and
the presense of '/' in a directory entry, but verify_dirent_name() also
ends up doing the proper name length verification which is what the
input checking discussion was about.
[ Another option would be to remove the support for this particular very
old interface: any binaries that use it are likely a.out binaries, and
they will no longer run anyway since we removed a.out binftm support
in commit eac616557050 ("x86: Deprecate a.out support").
But I'm not sure which came first: getdents() or ELF support, so let's
pretend somebody might still have a working binary that uses the
legacy readdir() case.. ]
Link: https://lore.kernel.org/lkml/CAHk-=wjbvzCAhAtvG0d81W5o0-KT5PPTHhfJ5ieDFq+bGtgOYg@mail.gmail.com/
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gcc-11 with KASAN on 32-bit arm produces a warning about a function
that needs a lot of stack space:
drivers/net/wireless/cisco/airo.c: In function 'setup_card.constprop':
drivers/net/wireless/cisco/airo.c:3960:1: error: the frame size of 1512 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
Most of this is from a single large structure that could be dynamically
allocated or moved into the per-device structure. However, as the callers
all seem to have a fairly well bounded call chain, the easiest change
is to pull out the part of the function that needs the large variables
into a separate function and mark that as noinline_for_stack. This does
not reduce the total stack usage, but it gets rid of the warning and
requires minimal changes otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323131634.2669455-1-arnd@kernel.org
|
|
gcc complains about undefined behavior in calling snprintf()
with the same buffer as input and output:
drivers/net/wireless/ti/wl18xx/debugfs.c: In function 'diversity_num_of_packets_per_ant_read':
drivers/net/wireless/ti/wl18xx/../wlcore/debugfs.h:86:3: error: 'snprintf' argument 4 overlaps destination object 'buf' [-Werror=restrict]
86 | snprintf(buf, sizeof(buf), "%s[%d] = %d\n", \
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
87 | buf, i, stats->sub.name[i]); \
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ti/wl18xx/debugfs.c:24:2: note: in expansion of macro 'DEBUGFS_FWSTATS_FILE_ARRAY'
24 | DEBUGFS_FWSTATS_FILE_ARRAY(a, b, c, wl18xx_acx_statistics)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ti/wl18xx/debugfs.c:159:1: note: in expansion of macro 'WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY'
159 | WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY(diversity, num_of_packets_per_ant,
There are probably other ways of handling the debugfs file, without
using on-stack buffers, but a simple workaround here is to remember the
current position in the buffer and just keep printing in there.
Fixes: bcca1bbdd412 ("wlcore: add debugfs macro to help print fw statistics arrays")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323125723.1961432-1-arnd@kernel.org
|
|
Building without mesh supports shows a couple of warnings with
'make W=1':
drivers/net/wireless/marvell/libertas/main.c: In function 'lbs_start_card':
drivers/net/wireless/marvell/libertas/main.c:1068:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
1068 | lbs_start_mesh(priv);
Change the macros to use the usual "do { } while (0)" instead to shut up
the warnings and make the code a litte more robust.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210322104343.948660-4-arnd@kernel.org
|
|
The 'c2hcmd_lock' spinlock is only used to protect some __skb_queue_tail()
and __skb_dequeue() calls.
Use the lock provided in the skb itself and call skb_queue_tail() and
skb_dequeue(). These functions already include the correct locking.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/8bcec6429615aeb498482dc7e1955ce09b456585.1617613700.git.christophe.jaillet@wanadoo.fr
|
|
If the loop fails, the "while(trials--) {" loop will exit with "trials"
set to -1. The test for that expects it to end with "trials" set to 0
so the warning message will not be printed.
Fix this by changing from a post-op to a pre-op. This does mean that
we only make 99 attempts instead of 100 but that's okay.
Fixes: f135a1571a05 ("wilc1000: Support chip sleep over SPI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YFS5gx/gi70zlIaO@mwanda
|
|
Remove unneeded variable: "ret"
Signed-off-by: zuoqilin <zuoqilin@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210317063353.1055-1-zuoqilin1@163.com
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix
multiple warnings by replacing /* fall through */ comments with
the new pseudo-keyword macro fallthrough; instead of letting the
code fall through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210305094850.GA141221@embeddedor
|
|
Linux network drivers normally disallow changing the MAC address when
the interface is up. This driver has been different in that it allows
to change the MAC address *only* when it's up. This patch brings
wilc1000 behavior more in line with other network drivers. We could
have replaced wilc_set_mac_addr() with eth_mac_addr() but that would
break existing documentation on how to change the MAC address.
Likewise, return -EADDRNOTAVAIL (not -EINVAL) when the specified MAC
address is invalid or unavailable.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210303194846.1823596-1-davidm@egauge.net
|
|
The driver so far has always disabled CRC protection. This means any
data corruption that occurrs during the SPI transfers could go
undetected. This patch adds module parameters enable_crc7 and
enable_crc16 to selectively turn on CRC7 (for command transfers) and
CRC16 (for data transfers), respectively.
The default configuration remains unchanged, with both CRC7 and CRC16
off.
The performance impact of CRC was measured by running ttcp -t four
times in a row on a SAMA5 device:
CRC7 CRC16 Throughput: Standard deviation:
---- ----- ----------- -------------------
off off 1720 +/- 48 KB/s
on off 1658 +/- 58 KB/s
on on 1579 +/- 84 KB/s
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-4-davidm@egauge.net
|
|
After a DMA write to the WILC chip, check for and report any errors.
This is based on code from the wilc driver in the linux-at91
repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-3-davidm@egauge.net
|
|
The WILC1000 protocol control register has bits for enabling the CRCs
(CRC7 for commands and CRC16 for data) and to set the data packet
size. Define symbolic names for those so the code is more easily
understood.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-2-davidm@egauge.net
|
|
For CMD_SINGLE_READ and CMD_INTERNAL_READ, WILC may insert one or more
zero bytes between the command response and the DATA Start tag (0xf3).
This behavior appears to be undocumented in "ATWILC1000 USER GUIDE"
(https://tinyurl.com/4hhshdts) but we have observed 1-4 zero bytes
when the SPI bus operates at 48MHz and none when it operates at 1MHz.
This code is derived from the equivalent code of the wilc driver in
the linux-at91 repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-1-davidm@egauge.net
|
|
There are a few reasons not to dump SSIDs as-is in kernel logs:
1) they're not guaranteed to be any particular text encoding (UTF-8,
ASCII, ...) in general
2) it's somewhat redundant; the BSSID should be enough to uniquely
identify the AP/STA to which we're connecting
3) BSSIDs have an easily-recognized format, whereas SSIDs do not (they
are free-form)
4) other common drivers (e.g., everything based on mac80211) get along
just fine by only including BSSIDs when logging state transitions
Additional notes on reason #3: this is important for the
privacy-conscious, especially when providing tools that convey
kernel logs on behalf of a user -- e.g., when reporting bugs. So for
example, it's easy to automatically filter logs for MAC addresses, but
it's much harder to filter SSIDs out of unstructured text.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225024454.4106485-1-briannorris@chromium.org
|
|
The "ext->key_len" is a u16 that comes from the user. If it's over
SCM_KEY_LEN (32) that could lead to memory corruption.
Fixes: e0d369d1d969 ("[PATCH] ieee82011: Added WE-18 support to default wireless extension handler")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YHaoA1i+8uT4ir4h@mwanda
|
|
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1617711406-49649-1-git-send-email-huangguobin4@huawei.com
|
|
some function's label meaningless, the label statement follows
the goto statement, no other statements, so just remove it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210406025206.4924-1-samirweng1979@163.com
|
|
The 'c2hcmd_lock' spinlock is only used to protect some __skb_queue_tail()
and __skb_dequeue() calls.
Use the lock provided in the skb itself and call skb_queue_tail() and
skb_dequeue(). These functions already include the correct locking.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/99cf8894fd52202cb7ce2ec6e3200eef400bc071.1617609346.git.christophe.jaillet@wanadoo.fr
|
|
'rtl_get_tid_h()' is the same as 'ieee80211_get_tid()'.
So this function can be removed to save a line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/db340a67a95c119e4f9ba8fa99aea1c73d0dcfc9.1617383263.git.christophe.jaillet@wanadoo.fr
|
|
rtlpriv->btcoexist.reg_bt_sco
Assigning value "3" to "rtlpriv->btcoexist.reg_bt_sco" here, but that
stored value is overwritten before it can be used.
Coverity reports this problem as
CWE563: A value assigned to a variable is never used.
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c:
rtl8188ee_bt_reg_init
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1617182023-110950-1-git-send-email-yang.lee@linux.alibaba.com
|
|
Variable err is assigned -ENODEV followed by an error return path
via label error_out that does not access the variable and returns
with the -ENODEV error return code. The assignment to err is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210327230014.25554-1-colin.king@canonical.com
|
|
s/resovle/resolve/
s/broadcase/broadcast/
s/sytem/system/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210320194426.21621-1-unixbhaskar@gmail.com
|
|
some function's label meaningless, the return statement follows
the goto statement, so just remove it.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210223065754.34392-1-samirweng1979@163.com
|
|
The signal strength of 5G is quite low, so user can't connect to an AP far
away. New parameters with new format and its parser are updated by the commit
84d26fda52e2 ("rtlwifi: Update 8821ae new phy parameters and its parser."), but
some parameters are missing. Use this commit to update to the novel parameters
that use new format.
Fixes: 84d26fda52e2 ("rtlwifi: Update 8821ae new phy parameters and its parser")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219052607.7323-1-pkshih@realtek.com
|
|
Remove the 'wsm_*' typedef as it is not used.
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613449833-4910-1-git-send-email-chen45464546@163.com
|
|
Remove the 'cw1200_wsm_handler' typedef as it is not used.
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613446918-4532-1-git-send-email-chen45464546@163.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.12-rc8, including fixes from netfilter, and
bpf. BPF verifier changes stand out, otherwise things have slowed
down.
Current release - regressions:
- gro: ensure frag0 meets IP header alignment
- Revert "net: stmmac: re-init rx buffers when mac resume back"
- ethernet: macb: fix the restore of cmp registers
Previous releases - regressions:
- ixgbe: Fix NULL pointer dereference in ethtool loopback test
- ixgbe: fix unbalanced device enable/disable in suspend/resume
- phy: marvell: fix detection of PHY on Topaz switches
- make tcp_allowed_congestion_control readonly in non-init netns
- xen-netback: Check for hotplug-status existence before watching
Previous releases - always broken:
- bpf: mitigate a speculative oob read of up to map value size by
tightening the masking window
- sctp: fix race condition in sctp_destroy_sock
- sit, ip6_tunnel: Unregister catch-all devices
- netfilter: nftables: clone set element expression template
- netfilter: flowtable: fix NAT IPv6 offload mangling
- net: geneve: check skb is large enough for IPv4/IPv6 header
- netlink: don't call ->netlink_bind with table lock held"
* tag 'net-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
netlink: don't call ->netlink_bind with table lock held
MAINTAINERS: update my email
bpf: Update selftests to reflect new error states
bpf: Tighten speculative pointer arithmetic mask
bpf: Move sanitize_val_alu out of op switch
bpf: Refactor and streamline bounds check into helper
bpf: Improve verifier error messages for users
bpf: Rework ptr_limit into alu_limit and add common error path
bpf: Ensure off_reg has no mixed signed bounds for all types
bpf: Move off_reg into sanitize_ptr_alu
bpf: Use correct permission flag for mixed signed bounds arithmetic
ch_ktls: do not send snd_una update to TCB in middle
ch_ktls: tcb close causes tls connection failure
ch_ktls: fix device connection close
ch_ktls: Fix kernel panic
i40e: fix the panic when running bpf in xdpdrv mode
net/mlx5e: fix ingress_ifindex check in mlx5e_flower_parse_meta
net/mlx5e: Fix setting of RS FEC mode
net/mlx5: Fix setting of devlink traps in switchdev mode
Revert "net: stmmac: re-init rx buffers when mac resume back"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"The largest change is for a regression that landed during -rc1 for
block-device read-only handling. Vaibhav found a new use for the
ability (originally introduced by virtio_pmem) to call back to the
platform to flush data, but also found an original bug in that
implementation. Lastly, Arnd cleans up some compile warnings in dax.
This has all appeared in -next with no reported issues.
Summary:
- Fix a regression of read-only handling in the pmem driver
- Fix a compile warning
- Fix support for platform cache flush commands on powerpc/papr"
* tag 'libnvdimm-fixes-for-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/region: Fix nvdimm_has_flush() to handle ND_REGION_ASYNC
libnvdimm: Notify disk drivers to revalidate region read-only
dax: avoid -Wempty-body warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL memory class fixes from Dan Williams:
"A collection of fixes for the CXL memory class driver introduced in
this release cycle.
The driver was primarily developed on a work-in-progress QEMU
emulation of the interface and we have since found a couple places
where it hid spec compliance bugs in the driver, or had a spec
implementation bug itself.
The biggest change here is replacing a percpu_ref with an rwsem to
cleanup a couple bugs in the error unwind path during ioctl device
init. Lastly there were some minor cleanups to not export the
power-management sysfs-ABI for the ioctl device, use the proper sysfs
helper for emitting values, and prevent subtle bugs as new
administration commands are added to the supported list.
The bulk of it has appeared in -next save for the top commit which was
found today and validated on a fixed-up QEMU model.
Summary:
- Fix support for CXL memory devices with registers offset from the
BAR base.
- Fix the reporting of device capacity.
- Fix the driver commands list definition to be disconnected from the
UAPI command list.
- Replace percpu_ref with rwsem to fix initialization error path.
- Fix leaks in the driver initialization error path.
- Drop the power/ directory from CXL device sysfs.
- Use the recommended sysfs helper for attribute 'show'
implementations"
* tag 'cxl-fixes-for-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/mem: Fix memory device capacity probing
cxl/mem: Fix register block offset calculation
cxl/mem: Force array size of mem_commands[] to CXL_MEM_COMMAND_ID_MAX
cxl/mem: Disable cxl device power management
cxl/mem: Do not rely on device_add() side effects for dev_set_name() failures
cxl/mem: Fix synchronization mechanism for device removal vs ioctl operations
cxl/mem: Use sysfs_emit() for attribute show routines
|
|
Merge misc fixes from Andrew Morton:
"12 patches.
Subsystems affected by this patch series: mm (documentation, kasan,
and pagemap), csky, ia64, gcov, and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib: remove "expecting prototype" kernel-doc warnings
gcov: clang: fix clang-11+ build
mm: ptdump: fix build failure
mm/mapping_dirty_helpers: guard hugepage pud's usage
ia64: tools: remove duplicate definition of ia64_mf() on ia64
ia64: tools: remove inclusion of ia64-specific version of errno.h header
ia64: fix discontig.c section mismatches
ia64: remove duplicate entries in generic_defconfig
csky: change a Kconfig symbol name to fix e1000 build error
kasan: remove redundant config option
kasan: fix hwasan build for gcc
mm: eliminate "expecting prototype" kernel-doc warnings
|
|
The return value on success (>= 0) is overwritten by the return value of
put_old_timex32(). That works correct in the fault case, but is wrong for
the success case where put_old_timex32() returns 0.
Just check the return value of put_old_timex32() and return -EFAULT in case
it is not zero.
[ tglx: Massage changelog ]
Fixes: 3a4d44b61625 ("ntp: Move adjtimex related compat syscalls to native counterparts")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210414030449.90692-1-chenjun102@huawei.com
|
|
While this code is executed with the wait_lock held, a reader can
acquire the lock without holding wait_lock. The writer side loops
checking the value with the atomic_cond_read_acquire(), but only truly
acquires the lock when the compare-and-exchange is completed
successfully which isn’t ordered. This exposes the window between the
acquire and the cmpxchg to an A-B-A problem which allows reads
following the lock acquisition to observe values speculatively before
the write lock is truly acquired.
We've seen a problem in epoll where the reader does a xchg while
holding the read lock, but the writer can see a value change out from
under it.
Writer | Reader
--------------------------------------------------------------------------------
ep_scan_ready_list() |
|- write_lock_irq() |
|- queued_write_lock_slowpath() |
|- atomic_cond_read_acquire() |
| read_lock_irqsave(&ep->lock, flags);
--> (observes value before unlock) | chain_epi_lockless()
| | epi->next = xchg(&ep->ovflist, epi);
| | read_unlock_irqrestore(&ep->lock, flags);
| |
| atomic_cmpxchg_relaxed() |
|-- READ_ONCE(ep->ovflist); |
A core can order the read of the ovflist ahead of the
atomic_cmpxchg_relaxed(). Switching the cmpxchg to use acquire
semantics addresses this issue at which point the atomic_cond_read can
be switched to use relaxed semantics.
Fixes: b519b56e378ee ("locking/qrwlock: Use atomic_cond_read_acquire() when spinning in qrwlock")
Signed-off-by: Ali Saidi <alisaidi@amazon.com>
[peterz: use try_cmpxchg()]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Waiman Long <longman@redhat.com>
Tested-by: Steve Capper <steve.capper@arm.com>
|
