| Age | Commit message (Collapse) | Author |
|---|
|
And clean up some stray spaces.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.
Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Rather than waiting for trigger bits, the formula for which was slightly
messy, and apparently, not actually 100% complete for some remotes, just
call ir_raw_event_handle whenever we finish parsing a chunk of data from
the rx fifo, similar to mceusb, as well as whenever we see an 'end of
signal data' 0x80 packet.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reported by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Adapt to recent videobuf_queue_dma_contig_init signature change.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This removes the '+1' in vsync timing calculation for wm8505fb to
directly use values provided from the board setup code.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This replaces the last remaining driver name reference with the
macro for uniformity in wm8505fb.
In addition, the error return path in wmt_ge_rops.c is made more
uniform by getting rid of goto's in remaining places.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Silence warnings such as -
drivers/video/s1d13xxxfb.c:421: warning: ‘bltbit_wait_bitset’ defined but not used
Just drop the unused code.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds support for runtime pm using the functions.
- pm_runtime_get_sync()
- pm_runtime_put_sync()
pm_runtime_get_sync() and pm_runtime_put_sync() are called when
open or release function of framebufer driver is called to inform
the system if hardware is idle or not.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Conflicts:
arch/arm/mach-shmobile/include/mach/entry-macro.S
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Increase NR_IRQS from 512 to 1024 on SH-Mobile ARM.
Needed to support vectors in the sh73a0 INTCS block.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Use PAGE_OFFSET and PHYS_OFFSET for secondary_startup
entry point as recommended by Russell King.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
smp.c is becoming too large, so split out the TLB maintainence
broadcasting into a separate smp_tlb.c file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When a CPU is hot unplugged, the generic tick code cleans up the
clock event device, but fails to call down to the device's set_mode
function to actually shut the device down.
To work around this, we've historically had a local_timer_stop()
callback out of the hotplug code. However, this adds needless
complexity when we have the clock event device itself available.
Explicitly call the clock event device's set_mode function with
CLOCK_EVT_MODE_UNUSED, so that the hardware can be cleanly shutdown
without any special external callbacks. When/if the generic code
is fixed, percpu_timer_stop() can be killed off.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use the definition we've provided in asm/system.h rather than
numeric constants.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The original scheme for reporting spurious wakeups was broken - it
tried to use printk() from a context which wasn't coherent with the
other CPUs, which risks corrupting the printk() data.
Fix this by noting the number spurious wakeups, and only report them
when we are properly woken - when we will be coherent with the rest
of the system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We used to print a bland error message which gave no clue as to the
failure when we failed to bring up a secondary CPU. Resolve this by
separating the two failure cases.
If boot_secondary() fails, we print a message indicating the returned
error code from boot_secondary():
"CPU%u: failed to boot: %d\n", cpu, ret.
However, if boot_secondary() succeeded, but the CPU did not appear to
mark itself online within the timeout, indicate that it failed to come
online:
"CPU%u: failed to come online\n", cpu
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We can not guarantee that VFP will be enabled when CPU hotplug brings
a CPU back online from a reset state. Add a hotplug CPU notifier to
ensure that the VFP coprocessor access is enabled whenever a CPU comes
back online.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There is a subtle race in the CPU hotplug code, where a CPU which has
been offlined can online itself before being requested, which results
in things going astray on the next online/offline cycle.
What happens in the normal online/offline/online cycle is:
CPU0 CPU3
requests boot of CPU3
pen_release = 3
flush cache line
checks pen_release, reads 3
starts boot
pen_release = -1
... requests CPU3 offline ...
... dies ...
checks pen_release, reads -1
requests boot of CPU3
pen_release = 3
flush cache line
checks pen_release, reads 3
starts boot
pen_release = -1
However, as the write of -1 of pen_release is not fully flushed back to
memory, and the checking of pen_release is done with caches disabled,
this allows CPU3 the opportunity to read the old value of pen_release:
CPU0 CPU3
requests boot of CPU3
pen_release = 3
flush cache line
checks pen_release, reads 3
starts boot
pen_release = -1
... requests CPU3 offline ...
... dies ...
checks pen_release, reads 3
starts boot
pen_release = -1
requests boot of CPU3
pen_release = 3
flush cache line
Fix this by grouping the write of pen_release along with its cache line
flushing code to ensure that any update to pen_release is always pushed
out to physical memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* __fixup_smp_on_up has been modified with support for the
THUMB2_KERNEL case. For THUMB2_KERNEL only, fixups are split
into halfwords in case of misalignment, since we can't rely on
unaligned accesses working before turning the MMU on.
No attempt is made to optimise the aligned case, since the
number of fixups is typically small, and it seems best to keep
the code as simple as possible.
* Add a rotate in the fixup_smp code in order to support
CPU_BIG_ENDIAN, as suggested by Nicolas Pitre.
* Add an assembly-time sanity-check to ALT_UP() to ensure that
the content really is the right size (4 bytes).
(No check is done for ALT_SMP(). Possibly, this could be fixed
by splitting the two uses ot ALT_SMP() (ALT_SMP...SMP_UP versus
ALT_SMP...SMP_UP_B) into two macros. In the first case,
ALT_SMP needs to expand to >= 4 bytes, not == 4.)
* smp_mpidr.h (which implements ALT_SMP()/ALT_UP() manually due
to macro limitations) has not been modified: the affected
instruction (mov) has no 16-bit encoding, so the correct
instruction size is satisfied in this case.
* A "mode" parameter has been added to smp_dmb:
smp_dmb arm @ assumes 4-byte instructions (for ARM code, e.g. kuser)
smp_dmb @ uses W() to ensure 4-byte instructions for ALT_SMP()
This avoids assembly failures due to use of W() inside smp_dmb,
when assembling pure-ARM code in the vectors page.
There might be a better way to achieve this.
* Kconfig: make SMP_ON_UP depend on
(!THUMB2_KERNEL || !BIG_ENDIAN) i.e., THUMB2_KERNEL is now
supported, but only if !BIG_ENDIAN (The fixup code for Thumb-2
currently assumes little-endian order.)
Tested using a single generic realview kernel on:
ARM RealView PB-A8 (CONFIG_THUMB2_KERNEL={n,y})
ARM RealView PBX-A9 (SMP)
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
With "ARM: CPU hotplug: remove bug checks in platform_cpu_die()", we
now do not use hard_smp_processor_id(), we no longer need to read the
hardware processor ID. Remove the include providing this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Don't call idle_task_exit() with interrupts disabled, and ensure
that we have a memory barrier after interrupts are disabled but
before signalling that this CPU has shut down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
platform_cpu_die() is entered from the CPU's own idle thread, which
can not be migrated to other CPUs. Moreover, the 'cpu' argument
comes from the thread info, which will always be the 'current'
CPU. So remove this useless bug check.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We always need to wait for the dying CPU to reach a safe state before
taking it down, irrespective of the requirements of the platform.
Move the completion code into the ARM SMP hotplug code rather than
having each platform re-implement this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
All platforms call trace_hardirqs_off() in their secondary startup code,
so move this into the core SMP code - it doesn't need to be in the
per-platform code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There is a certain amount of smp_prepare_cpus() which doesn't belong
in the platform support code - that is, code which is invariant to the
SMP implementation. Move this code into arch/arm/kernel/smp.c, and
add a platform_ prefix to the original function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Milo is an old boot loader, which is no longer relevant for these
platforms. References to it are misleading. Move the code out
of poke_milo(), and remove references to milo in comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We don't need this small function as well as scu_get_core_count()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
scu_get_core_count() never returns zero cores, so we don't need to
check and correct if ncores is zero.
Tegra was missing the check against NR_CPUS, leading to a potential
bitfield overflow if this becomes the case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Ensure that the number of CPUs is sanity checked before setting
the number of possible CPUs. This avoids any chance of overflowing
the cpu_possible bitmap.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Wait for CPUs to indicate that they've stopped, after sending the
stop IPI, rather than blindly continuing on and hoping that they've
stopped in time. Print a warning if we fail to stop the other CPUs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use r0,r3-r6 rather than r0,r3,r4,r6,r7, which makes it easier to
understand which registers can be modified. Also document which
registers hold values which must be preserved.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The IPI and local timer interrupts weren't being properly accounted
for in /proc/stat. Collect them from the irq_stat structure, and
return their sum.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This separates out the individual IPI interrupt counts from the
total IPI count, which allows better visibility of what IPIs are
being used for.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Tested on a Colibri Evaluation Board Rev.2.1 with a Colibri PXA310 module.
Signed-off-by: Bjorn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
|
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
