| Age | Commit message (Collapse) | Author |
|---|
|
Add dev_close_many and dev_deactivate_many to factorize another
sync-rcu operation on the netdevice unregister path.
$ modprobe dummy numdummies=10000
$ ip link set dev dummy* up
$ time rmmod dummy
Without the patch With the patch
real 0m 24.63s real 0m 5.15s
user 0m 0.00s user 0m 0.00s
sys 0m 6.05s sys 0m 5.14s
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add USB OTG, peripheral and host devices. This patch also adds
usb_phy_clk which is required for resetting the PHY. VBUS power up
and shutdown routines depends on PMIC module. As PMIC driver is
unavailable, configure USB in peripheral only mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
OTG driver takes care of putting hardware into low power mode. Hence
make peripheral and host devices as children of OTG device and let
runtime PM takes care of notifying peripheral and host state to
OTG device. VBUS power up and shutdown routines are implemented by
modem processor. As RPC infrastructure is not available, configure
USB in peripheral only mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing
protocol for multi-hop ad-hoc mesh networks. The networks may be wired or
wireless. See http://www.open-mesh.org/ for more information and user space
tools.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Willem-Jan noticed that the ftdi_sio driver did not support the
TIOCSERGETLSR ioctl, and some userspace programs rely on it. This patch
adds the support.
Reported-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Tested-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In order to read/write to the i.MX OTG viewport register it is necessary to setup
the PORTSCx register first.
By default i.MX OTG port is configured for USB serial PHY. In order to use a ULPI PHY
the PORTSCx register needs to be configured properly.
commit 724c852 (USB: ehci/mxc: compile fix) placed the PORTSC setup after the OTG
viewport is accessed and this causes ULPI read/write to fail.
Revert the PORTSC setup order.
Tested on a MX31PDK board with a ISP1504 transceiver:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
mxc-ehci mxc-ehci.0: initializing i.MX USB Controller
ULPI transceiver vendor/product ID 0x04cc/0x1504
Found NXP ISP1504 ULPI transceiver.
ULPI integrity check: passed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add a free_irq() call on vbus gpio when we remove udc so that the
vbus irq is properly released.
Signed-off-by: Rob Emanuele <rje@crystalfontz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The TLL channel enable code searches for the wrong mask, and
could end up enabling the wrong port. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is the ohci-omap3 driver, not ehci-omap. Correct this
obvious typo.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Page size for transaction descriptors for CI13XXX has nothing
common with page size from MM. Using platform and configuration
specific PAGE_SIZE is wrong.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
CI13xxx UDC driver doesn't call complete() callback for requests
with flag no_interrupt set. Thus gadget drivers (like g_ether) are
never notifed about successfully (or not) transmitted requests. As
a result in case of g_ether and queued request with no_interrupt=1
fields g_ether is never notifed about sent packets and TX stalls.
Solution: treat no_interrupt flag like all other UDC drivers do and
call complete() callback for all requests.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There is one nasty scenario when CI13xxx driver fails:
a) two or more rx requests are queued (g_ether does that)
b) rx request completed, interrupt fires and ci13xxx dequeues rq
c) request complete() callback gets called and in turn it calls ep_queue()
c1) in ep_queue() request gets added to the TAIL of the rx queue list
d) ep gets primed with rq from (b)
e) interrupt fires
f) request gets popped from queue head for hw dequeue
G) requets from queue head wasn't enqueued
g1) isr_tr_complete_low() doesn't
enqueue more requests and it doesn't prime EP,
rx traffic stalls
Solution:
a) enque queued requests ASAP, i.e. before calling complete() callback.
b) don't HW enqueue and prime endpoint with recently added request and
use the oldest request in the queue.
Fixed issues:
a) ep_queue() may return an error code despite request was successfully
added to the queue (if _hardware_enqueue() fails)
b) Added requests are always processed in LIFO order, even if they are
added in complete() callback
c) Finally more than two and more queued requests are processed consistently,
even if they were added in complete() callback
The fix was successfully tested on MIPS based SoC with 4KEc CPU core and
CI13612 USB core. Board successfully boots with NFS root using g_ether
on ci13xxx udc.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Built-in gadget drivers have NULL-ifed unbind() function. Checking
whether unbind() is NULL will never let any compiled into kernel
driver attach.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provices the debugfs interface to see RLB hash table
like the following:
# cat /sys/kernel/debug/bonding/bond0/rlb_hash_table
SourceIP DestinationIP Destination MAC DEV
10.124.196.205 10.124.196.205 ff:ff:ff:ff:ff:ff eth4
10.124.196.205 10.124.196.81 00:19:99:XX:XX:XX eth3
10.124.196.205 10.124.196.1 00:21:d8:XX:XX:XX eth0
This is helpful to check if the receive load balancing works as expected.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch simply migrates some macros from bond_alb.c to bond_alb.h.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate Tx queue memory on the node indicated by the new
netdev_queue_numa_node_read.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current code parses the VPD RO section for keywords but makes static
assumptions about the location of the section. Remove them and parse
the VPD to find it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch originally from Joe Perches, unmodified.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver keeps a bitmap of the netdevs it registered so it knows what to
unregister later. Remove that and look at reg_state instead.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove a field the driver uses to keep track of the name of the first
netdev it manages to register. Do this by changing the registration
loop to stop the first time it fails so the first registered device is
trivial to tell.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last byte of the buffer for MSI-X names could not be used due to a
bogus -1. Also do not explicitly clear the last byte, snprintf will do
the right thing.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently MSI-X names for netdevs with long names are truncated in
/proc/interrupts due to insufficient space. Use IFNAMSIZ to size the
needed space.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Print information about each port when its netdev is registered instead
of looping separately over the ports at the end. The bulk of this patch
is due to indentation change.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And fix the supported flags ethtool reports for the two cases.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of queues is known early, move the calls to
netif_set_real_num_[rt]x_queues before register_netdev.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to read the clock frequency from VPD, we already get it a bit
later from FW, after any potential adjustments.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable relaxed ordering for descriptor reads and packet I/O.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Includes FCoE releated fixes in FW flows
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add appropriate HW DCB/PFC configuration
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding DCB initialization and handling on 57712 FW/HW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This callback required to allow FCoE traffic to be
sent on separate priority queue from other L2 traffic,
which is managed by PFC in HW.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Includes new driver structures and FW/HW configuration for FCoE ring
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the calcualation of the Tx hash for a given hash range into a separate
function and define the skb_tx_hash(), which calculates a Tx hash for a
[0; dev->real_num_tx_queues - 1] hash values range, using this
function (__skb_tx_hash()).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The apbuart driver depends on OF and relies on everything being
available. So if it's probed on a platform which has OF support, but
no device tree is available it crashes. Triggered by the upcoming x86
OF support in randconfig testing.
Further it's inconsistent vs. the probing and exiting from the
of_match loop.
Make it robust and consistent:
- check the availablility of OF nodes before dereferencing
- return -ENODEV when the device tree lookup fails
- return -ENODEV when no uart port configuration is found
- return -ENODEV when invalid uart port configuration is found
Remove the enum_done check while at it. Driver init functions are only
called once. Remove the pointless vendor and device queries as well.
Reported-by: Ingo Molnar <mingo.elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
To avoid unbalanced IRQ wake disable, ensure that wakeups are disabled
only when wakeups have been successfully enabled.
Tested on OMAP3630SDP/ZOOM3.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix various typos and other errors in comments of tty_driver.h. The most
significant is the wrong name of a function for the description of
TTY_DRIVER_DYNAMIC_DEV.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix the following warnings
drivers/serial/pch_uart.c: In function ‘dma_handle_rx’:
drivers/serial/pch_uart.c:685:24: warning: cast from pointer to integer of different size
drivers/serial/pch_uart.c: In function ‘dma_handle_tx’:
drivers/serial/pch_uart.c:778:23: warning: cast from pointer to integer of different size
drivers/serial/pch_uart.c: In function ‘pch_uart_init_port’:
drivers/serial/pch_uart.c:1289:20: warning: cast to pointer from integer of different size
drivers/serial/pch_uart.c: In function ‘pch_uart_exit_port’:
drivers/serial/pch_uart.c:1328:2: warning: cast from pointer to integer of different size
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reported-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
gsm_data_alloc buffer allocation could fail and it is not being checked.
Add check for allocated buffer and return if the buffer allocation
fails.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix message length handling when building header
When the message length is greater than 127, the length field in the header
is built incorrectly. According to the spec, when the length is less than 128
the length field is a single byte formatted as: bbbbbbb1. When it is greater
than 127 then the field is two bytes of the format: bbbbbbb0 bbbbbbbb.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
bond_na_send() attempts to insert a VLAN tag in between building and
sending packets of the respective formats. If the slave does not
implement hardware VLAN tag insertion then vlan_put_tag() will mangle
the network-layer header because the Ethernet header is not present at
this point (unlike in bond_arp_send()).
Fix this by adding the tag out-of-line and relying on
dev_hard_start_xmit() to insert it inline if necessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bond_change_active_slave() may be called when a slave is added, even
if the bond has not been brought up yet. It may then attempt to send
packets, and further it may use mcast_work which is uninitialised
before the bond is brought up. Add the necessary checks for
netif_running(bond->dev).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A bond may have a mixture of slave devices with and without hardware
VLAN tag insertion capability. Therefore it always claims this
capability and performs software VLAN tag insertion if the slave does
not.
Since commit 7b9c60903714bf0a19d746b228864bad3497284e, this has
also been done by dev_hard_start_xmit(). The result is that VLAN-
tagged skbs are now double-tagged when transmitted through slave
devices without hardware VLAN tag insertion!
Remove the now-redundant logic from bond_dev_queue_xmit().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
axnet_cs:
Accton EN2328 or compatible (id: 0x01bf, 0x2328) uses Asix chip.
So it works better with axnet_cs instead of pcnet_cs.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first big packets sent to a "low-MTU" client correctly
triggers the creation of a temporary route containing the reduced MTU.
But after the temporary route has expired, new ICMP6 "packet too big"
will be sent, rt6_pmtu_discovery will find the previous EXPIRED route
check that its mtu isn't bigger then in icmp packet and do nothing
before the temporary route will not deleted by gc.
I make the simple experiment:
while :; do
time ( dd if=/dev/zero bs=10K count=1 | ssh hostname dd of=/dev/null ) || break;
done
The "time" reports real 0m0.197s if a temporary route isn't expired, but
it reports real 0m52.837s (!!!!) immediately after a temporare route has
expired.
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The returned slave is incorrect, if the net device under check is not
charged yet by the master.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
