| Age | Commit message (Collapse) | Author |
|---|
|
Reduce fastpath overhead by making ena_com_tx_comp_req_id_get() inline.
Also move it to ena_eth_com.h file with its dependency function
ena_com_cq_inc_head().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Kees writes:
"Fix open-coded multiplication arguments to allocators
- Fixes several new open-coded multiplications added in the 4.19
merge window."
* tag 'alloc-args-v4.19-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Replace more open-coded allocation size multiplications
|
|
Ido Schimmel says:
====================
mlxsw: Preparations for VxLAN support
This patchset prepares mlxsw for VxLAN support. It contains small and
mostly non-functional changes.
The first eight patches perform small changes in the code to make it
more receptive towards the actual VxLAN changes in the next patchset.
Patches 9-17 add the registers used to configure the device for VxLAN
offload.
Last two patches add the required resources and trap IDs.
The next patchset is available here [1].
1. https://github.com/idosch/linux/tree/vxlan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DECAP_ECN0 trap will be used to trap packets where the overlay
packet is marked with Non-ECT, but the underlay packet is marked with
either ECT(0), ECT(1) or CE. When trapped, such packets will be counted
as errors by the VxLAN driver and thus provide better visibility.
The NVE_ENCAP_ARP trap will be used to trap ARP packets undergoing NVE
encapsulation. This is needed in order to support E-VPN ARP suppression,
where the Linux bridge does not flood ARP packets through tunnel ports
in case it can answer the ARP request itself.
Note that all the packets trapped via these traps are marked with
'offload_fwd_mark', so as to not be re-flooded by the Linux bridge
through the ASIC ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the following resources to be used by the NVE code:
* Number of IPv4 underlay destination IPs in a single TNUMT record
* Number of IPv6 underlay destination IPs in a single TNUMT record
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register is used for setting up the parsing for hash, policy-engine
and routing.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Will be used to program the device with FDB records pointing to a NVE
tunnel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TNQDR register configures the default QoS settings for NVE
encapsulation.
It will be used to set the default DSCP of each port to 0, so that when
DSCP is set to inherit and the overlay packet does not have an IP header
the outer DSCP will be set to 0, in accordance with the software data
path.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register configures how QoS is set in Encapsulation into the
underlay network.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register configures the actions that are done during NVE
decapsulation based on the ECN bits.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register performs mapping from overlay ECN to underlay ECN during
NVE encapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register builds the linked list of underlay destination IPs used
for BUM traffic on the overlay.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register enables / disables learning on different types of tunnel
ports (e.g., NVE, VPLS).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register configures global NVE configuration such as source IP of
the NVE tunnel and UDP source port calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the seed of the LAG hash function is always set to 0, which
means it is identical across all switches. Instead, use a random number.
This is especially important now that VxLAN is supported, as the LAG
hash function is used to calculate the UDP source port of the
encapsulated packet.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device has the ability to flush all the FDB records that perform NVE
encapsulation or only a subset of these with a specific filtering
identifier (FID).
Expose these types so that they could be used by subsequent patches
where we need to flush the FDB records when an NVE device is unlinked
from a bridge (FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the device needs to flood an overlay packet to remote VTEPs it
retrieves a pointer to the head of a linked-list of records that store
the IP addresses of these VTEPs.
These records are stored in the KVD linear memory and configured via the
Tunneling NVE Underlay Multicast Table (TNUMT) register.
Add a new KVD linear entry type for these records, so that we will be
able to allocate and free them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L3 protocol and address definitions are going to be used by the NVE
code, so move them to the global header file from the one private to the
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VxLAN notifications are going to use a different notifier information
type, so cast to the correct type based on the received event.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VxLAN FDB updates are sent with the VxLAN device which is not our upper
and will therefore be ignored by current code.
Solve this by checking whether the upper device (bridge) is our upper.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VxLAN FDB notifications need to be handled differently than bridge FDB
notifications, so initialize the work item based on the received
notification and rename the invoked function accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The spectrum_router.h header file is private to the router block and
should only be included by direct consumers of it, such as dpipe and the
multicast routing code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c: In function 'cgx_fwi_event_handler':
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:257:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
It never be used since introduction in
commit 1463f382f58d ("octeontx2-af: Add support for CGX link management")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds reasonable comments, but they definitely needs better names.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch adds support for the NETIF_F_RXFCS feature in the Mscc
Ethernet driver. This feature is disabled by default and allow a user
to request the driver not to drop the FCS and to extract it into the skb
for debugging purposes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the introduction of the module area on top of the vmalloc area, the
calculation of VMALLOC_START in setup_memory_end() function hasn't been
adjusted. As a result we got vmalloc area 2 Gb (MODULES_LEN) smaller than
it should be and the preceding vmemmap area got extra memory instead.
The patch fixes this calculation error although there were no visible
negative effects.
Apart from that, change 'tmp' variable to 'vmemmap' in memory_end
calculation for better readability.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This is the SPI controller found on Marvel MMP2 and perhaps more
platforms.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
That seems to be the correct type.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver supports GENI based SPI Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including SPI. This driver supports SPI
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move GENI SE SPI controller device-tree bindings
from devicetree/bindings/soc/qcom/qcom,geni-se.txt
to devicetree/bindings/spi/qcom,spi-geni-qcom.txt.
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI controller driver should maintain the maximum frequency
of the controller instead of relying on device tree bindings.
Because maximum frequency is specific property of SPI
controller.
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Michael reported that he could not stat following event:
$ perf stat -e unc_p_freq_ge_1200mhz_cycles -a -- ls
event syntax error: '..e_1200mhz_cycles'
\___ value too big for format, maximum is 255
Run 'perf list' for a list of valid events
The event is unwrapped into:
uncore_pcu/event=0xb,filter_band0=1200/
where filter_band0 format says it's one byte only:
# cat uncore_pcu/format/filter_band0
config1:0-7
while JSON files specifies bigger number:
"Filter": "filter_band0=1200",
all the filter_band* formats show 1 byte width:
# cat uncore_pcu/format/filter_band1
config1:8-15
# cat uncore_pcu/format/filter_band2
config1:16-23
# cat uncore_pcu/format/filter_band3
config1:24-31
The reason of the issue is that filter_band* values are supposed to be
in 100Mhz units.. it's stated in the JSON help for the events, like:
filter_band3=XXX, with XXX in 100Mhz units
This patch divides the filter_band* values by 100, plus there's couple
of changes that actually change the number completely, like:
- "Filter": "edge=1,filter_band2=4000",
+ "Filter": "edge=1,filter_band2=30",
Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20181010080339.GB15790@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bindings for Qualcomm Quad SPI used on SoCs such as sdm845.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This compatible adds the ability for dw spi controller driver to work with
the dw spi controller found on Alpine chips.
The dw spi controller has an auto-deselect of Chip-Select, in case there is
no data inside the Tx FIFO. While working on platforms with Alpine chips,
auto-deselect mode causes an issue for some spi devices that can't handle
the Chip-Select deselect in the middle of a transaction. It is a normal
behavior for a Tx FIFO to be empty in the middle of a transaction, due to
busy cpu. In the Alpine chip family an option to change the default
behavior was added to the original dw spi controller to prevent this issue
of de-asserting Chip-Select once TX FIFO is empty. The change was to allow
SW manual control of the Chip-Select. With this change, as long as the
Slave Enable Register is asserted, the Chip-Select will be asserted. As a
result, it is necessary to deselect the Slave Select Register once the
transaction is done. This feature is enabled via a new device compatible
string called 'amazon,alpine-dw-apb-ssi'. Once the driver identifies the
new compatible string, it enables the hw fixup logic, by writing to a
dedicated register found in the IP reserved area and will start manual
deselecting the Slave Select Register when the transfer ends.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into spi-4.20
Immutable branch for QCOM Geni patches
|
|
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.
Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.
ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).
As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When there are few packets (e.g. for sampling attempts), the exponentially
weighted variance is usually vastly overestimated, making the resulting data
essentially useless. As far as I know, there has not been any practical use
for this, so let's not waste any cycles on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
These rates are highly unlikely to be used quickly, even if the link
deteriorates rapidly. This improves throughput in cases where CCK rates
are not reliable enough to be skipped entirely during sampling.
Sampling these rates regularly can cost a lot of airtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.
Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.
This improves throughput on 2.4 GHz channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
