| Age | Commit message (Collapse) | Author |
|---|
|
ControlvReadByte will be removed in next patch
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Create vnt_mac_set_led to set state and led.
state has two modes LEDSTS_TMLEN which sets the blink rate
on TX activity and LEDSTS_STS which sets the led.
As result of this patch ControlvMaskByte becomes dead code.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
add new function in usbpipe.c to replace ControlvWriteByte
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace all to CONTROLnsRequestIn with vnt_control_in and remove macro.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename all CONTROLnsRequestOut and remove macro from control.h
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace with dev_dbg
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
camel case changes
pDevice -> priv
wKeyCtl -> key_ctl
uEntryIdx -> entry_idx
uKeyIdx -> key_idx
pbyAddr -> addr
wOffset -> offset
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change pdwKey u32 pointer to key u8 pointer.
Callers are already u8 remove u32 pointer cast.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Originally, this header was defining two new typedefs, CMND_TYPE and
CMND_TYPE_SD, following this type of declaration:
typedef enum {
...
} CMND_TYPE;
A previous commit (785086556a573f07747b3633732a9dbd7e45728f) tried to
fix warnings that were pointed out by checkpatch.pl, concerning not
adding new typedefs. But this commit only removed the 'typedef' keyword,
thus transforming both the typedefs into two the definition of global
variables. For example:
enum {
...
} CMND_TYPE;
As noticed by the Sparse tool, this patch removes those erroneous global
variable definitions, and just leaves anonymous enum type definitions:
enum {
...
};
Signed-off-by: Joel Porquet <joel@porquet.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If printer_ports which is allocated after serial_ports is failed
to allocate, tty_port_init for serial_ports doesn't need anymore.
So move this after allocating memory for printer_ports.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When it failed to allocate for printer_ports, serial_ports
can be freed in dgap_tty_uninit().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In destruct_tty_driver() from put_tty_driver() will free the
ttys in tty_driver.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
iput() already checks for the inode being NULL, thus it's unnecessary to
check before calling.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added a blank line after declarations in many places to fix
the following warning issued by checkpatch.pl:
WARNING: Missing a blank line after declarations
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use regulator_set_voltage_time_sel() instead of open-coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
By default for every espi transfer, the rx_buf is placed right after the
tx_buf. This can lead to a buffer overflow when the size of both the TX
and RX data cumulated is higher than the allocated 64K buffer for the
transfer (this is the case when sending for instance a read command and
reading 64K back, please see:
http://article.gmane.org/gmane.linux.drivers.mtd/53411 )
This gets fixed by always setting the RX buffer pointer at the begining
of the transfer buffer.
[The driver shouldn't be doing the copy in the first place and instead
sending directly from the supplied buffer but this is at least not worse
than what's there -- broonie]
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit 932580409a9dacbf42215fa737bf06ae2c0aa624
"regmap: mmio: Add support for 1/2/8 bytes wide register address."
broke regmap_mmio_write for uneven counts, for example 32-bit register
addresses with no padding and 8-byte values (count = 5).
Fix this by allowing all counts large enough to include some value.
This check was BUG_ON(count < 4) before the last change.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The TPS658640 has a different set of output voltage for most LDO and
the RTC LDO isn't settable. This chip also report 2 different version
ID, as the datasheet doesn't list the possible values the second ID
has simply been named TPS658640v2.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add the required definitions and macros to allow easily adding fixed
regulators. This required for the TPS658640 that doesn't allow setting
the LDO_RTC output voltage.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Previously, the PFUZE100 would try to allocate gpio0 io0 because
config.ena_gpio defaults to 0, which can be a valid GPIO. To prevent this
from happening, set this parameter to -EINVAL.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The SWB regulators have the ability to be turned on and off. Add
enable/disable support for these regulators.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since we cannot make sure the 'chip->num_regs' will always be none zero
from the users, and then if 'chip->num_regs' equals to zero by mistake
or other reasons, the kzalloc() will return ZERO_SIZE_PTR, which equals
to ((void *)16).
So this patch fix this with just checking the 'chip->num_regs' before
calling kzalloc().
This also sorts the header files in alphabetical order at the same time.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds support for the Linear Technology LTC3589, LTC3589-1,
and LTC3589-2 8-output I2C voltage regulator ICs.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds the device tree binding documentation for Linear
Technology LTC3589, LTC3589-1, and LTC3589-2 8-port regulators.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add Linear Technology Corporation to the list of device tree vendor prefixes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Fix the register for ramp delay of buck1 regulator. Buck1 and buck6
share the field (offset 4) in ramp delay register S2MPA01_REG_RAMP2.
The driver used the same register and field for ramp delay of buck3 and
buck1. This lead to updating of ramp delay of buck3 when setting buck1
and actually the ramp delay of buck1 was never set.
Fixes: f18792714608 ("regulator: Add support for S2MPA01 regulator")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org>
|
|
Rejecting unsupported values of spi-tx-bus-width and spi-rx-bus-width
may break compatibility with future DTs. Just ignore them, falling back
to Single SPI Transfers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
list_voltage_linear_range
Use map_voltage_linear_range() if list_voltage_linear_range() is in use and
nothing is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The calculation of the bit rate divider used a standard C division, which
rounds down the quotient. This may lead to a higher bitrate than requested.
Round up to avoid this.
E.g. on Koelsch, the SPI flash (configured for 30 MHz) was driven at 48.75
MHz. After this patch it's driven at a safe 24.375 MHz.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
When the thermal module is to be removed, we should destroy the wq
acpi_thermal_pm_queue after the ACPI driver's remove callback is
executed as we will need to flush the workqueue there, or a NULL pointer
access will be hit.
Reported-and-tested-by: Kui Zhang <kuizhang@gmail.com>
References: http://www.spinics.net/lists/kernel/msg1747251.html
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The parent field of the 'rc32434_res_pci_mem1' resource points to
the resource itself which is obviously wrong. Due to the broken
initialitazion, the PCI devices on the Mikrotik RB532 boards are
not working since commit 22283178 (MIPS: avoid possible resource
conflict in register_pci_controller).
Remove the field initialization to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reported-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: linux-mips@linux-mips.org
Cc: Gabor Juhos <juhosg@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/6940/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Singed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Singed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
dependent upon the value to output!
Singed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Singed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Move the check for the QSPI config option inside the function body. If the
option is not enabled, the compiler will optimize away the empty function
body so we can remove the other check for the config option.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Use the correct base address for the QSPI module on the 5249/525x.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Since we now have fake clks on devices without real clocks, we need clks
defined for qspi for the qspi driver to work on those devices.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
In file included from arch/m68k/kernel/setup.c:4:0:
arch/m68k/kernel/setup_no.c:70:0: warning: "CPU_NAME" redefined [enabled by default]
#define CPU_NAME "MC68VZ328"
^
arch/m68k/kernel/setup_no.c:61:0: note: this is the location of the previous definition
#define CPU_NAME "MC68000"
^
Signed-off-by: Daniel Palmer <danieruru@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Daniel Palmer <danieruru@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
|
|
According to the ARM ARM, the behaviour is UNPREDICTABLE if the PC read
from the exception return stack is not half word aligned. See the
pseudo code for ExceptionReturn() and PopStack().
The signal handler's address has the bit 0 set, and setup_return()
directly writes this to regs->ARM_pc. Current hardware happens to
discard this bit, but QEMU's emulation doesn't and this makes processes
crash. Mask out bit 0 before the exception return in order to get
predictable behaviour.
Fixes: 19c4d593f0b4 ("ARM: ARMv7-M: Add support for exception handling")
Cc: stable@kernel.org
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds Qualcomm amba vendor Id to the list. This ID is used in mmci driver. The ID selected in same lines like 0x41 is "A" for ARM, 0x51 is "Q" for Qualcomm.
As there are no physical register on Qcom SOC for amba vendor id, this is a fake ID assigned based on "Q" prefix from Qualcomm.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The arm EABI states that unwind opcode 10100nnn means pop register r4-4[4+nnn],aditionally there is a similar unwind opcode: 10101nnn which means the same thing plus popping r14. Those two cases are handled by the unwind_exec_pop_r4_to_rN function which checks whether the 4th bit is set and does r14 popping.
However, up until now it has been checking whether the 8th bit was set (mask & 0x80) instead of the 4th (mask & 0x8), a simple to make typo but this meant that we were always popping r14 even if we had the former opcode.
This patch changes the mask so that the 2 unwind opcodes are being handled correctly.
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Reviewed-by: Anurag Aggarwal <anurag19aggarwal@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
According to arm procedure call standart r2 register is call-cloberred.
So after the result of x expression was put into r2 any following
function call in p may overwrite r2. To fix this, the result of p
expression must be saved to the temporary variable before the
assigment x expression to __r2.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
__v7m_setup_stack currently sits in the .proc.info.init section, and
thus creates a bogus proc info entry (which by the way matches any
unknown CPU IDs, due to the entry's mask being 0). Move it out of
there.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
