| Age | Commit message (Collapse) | Author |
|---|
|
Currently modular V4L2 build with enabled OF is broken dur to the
of_get_next_parent() function being unavailable to modules. Export it to
fix the build.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
For accurate accounting call contextidr_thread_switch before a
task is scheduled, rather than after, when the 'next' variable has a
different meaning since we switched the stacks.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The ESR_EL1 decoding process is a bit cryptic, and KVM has also
a need for the same constants.
Add a new esr.h file containing the appropriate exception classes
constants, and change entry.S to use it. Fix a small bug in the
EL1 breakpoint check while we're at it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Upon resume, it was found that ACPI C-states were missing from non-boot CPUs.
This change registers a syscore_ops handler for this case, and re-uploads the
PM information to the hypervisor to properly reset the C-state on these
processors.
v2:
v1 did not go through the check_acpi_ids() code-path, and missed some cases when
xen was running with the dom0_max_vcpus= command line parameter.
Signed-Off-By: Ben Guthro <benjamin.guthro@citrix.com>
[v3: Ate some tabs, s/printk/pr_info/]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
If the TPM has already been sent a SaveState command before the driver
is loaded it may have problems sending that same command again later.
This issue is seen with the Chromebook Pixel due to a firmware bug in
the legacy mode boot path which is sending the SaveState command
before booting the kernel. More information is available at
http://crbug.com/203524
This change introduces a retry of the SaveState command in the suspend
path in order to work around this issue. A future firmware update
should fix this but this is also a trivial workaround in the driver
that has no effect on systems that do not show this problem.
When this does happen the TPM responds with a non-fatal TPM_RETRY code
that is defined in the specification:
The TPM is too busy to respond to the command immediately, but the
command could be resubmitted at a later time. The TPM MAY return
TPM_RETRY for any command at any time.
It can take several seconds before the TPM will respond again. I
measured a typical time between 3 and 4 seconds and the timeout is set
at a safe 5 seconds.
It is also possible to reproduce this with commands via /dev/tpm0.
The bug linked above has a python script attached which can be used to
test for this problem. I tested a variety of TPMs from Infineon,
Nuvoton, Atmel, and STMicro but was only able to reproduce this with
LPC and I2C TPMs from Infineon.
The TPM specification only loosely defines this behavior:
TPM Main Level 2 Part 3 v1.2 r116, section 3.3. TPM_SaveState:
The TPM MAY declare all preserved values invalid in response to any
command other than TPM_Init.
TCG PC Client BIOS Spec 1.21 section 8.3.1.
After issuing a TPM_SaveState command, the OS SHOULD NOT issue TPM
commands before transitioning to S3 without issuing another
TPM_SaveState command.
TCG PC Client TIS 1.21, section 4. Power Management:
The TPM_SaveState command allows a Static OS to indicate to the TPM
that the platform may enter a low power state where the TPM will be
required to enter into the D3 power state. The use of the term "may"
is significant in that there is no requirement for the platform to
actually enter the low power state after sending the TPM_SaveState
command. The software may, in fact, send subsequent commands after
sending the TPM_SaveState command.
Change-Id: I52b41e826412688e5b6c8ddd3bb16409939704e9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
Using this parameter one can disable the storage_size/2 check if
he is really sure that the UEFI does sane gc and fulfills the spec.
This parameter is useful if a devices uses more than 50% of the
storage by default.
The Intel DQSW67 desktop board is such a sucker for exmaple.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
When setting voltage for AB8540_LDO_AUX3, current code only updates one of
info->voltage_reg and info->expand_register registers which is wrong.
To ensure we set to correct voltage, it always needs to clear or set
expand_register.voltage_mask bit of expand_register.
The function of the expand register bit is the following (from the user manual):
0: VAUX3 output voltage is determined by Vaux3Sel bit settings in register
VldoCVaux3Sel
1: VAUX3 output voltage is set to 3.05V regardless of Vaux3Sel settings in
register VldoCVaux3Sel (VldoCVaux3Sel is the register at 0x0421)
So when going to 3.05V, set the expand register bit.
When leaving 3.05V for another voltage, set the target voltage before clearing
the expand register bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Both enable() and disable() functions have only one caller, thus remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This ensures info->update_val status is still correct if set_mode() call fails.
Otherwise, get_mode() may return wrong status if a set_mode() call fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Currently, set invalid mode setting for shared mode regulators may change
sm->lp_mode_req flag. This patch ensures we don't set lp_mode_req flag to wrong
status if set_mode() fails.
This patch includes some clean up, and these changes makes this patch looks like
code refactor. The clean up is mainly to avoid adding ugly code to handle
failure paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch ensures info->update_val is consistent with current register value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
LDO8 of Palma device like tps65913 support the tracking mode
on which LDO8 track the SMPS45 voltage when SMPS45 is ON
and use the LDO8.VOLTAGE_SEL register when SMPS45 is OFF.
On track mode, the steps of voltage change for LDO8 is 25mV
where in non-tracking mode it is 50mV. Set the steps accordingly.
Number of voltage count is still same for both the cases.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Palmas device have control outputs like REGEN1, REGEN2, REGEN3,
SYSEN1 and SYSEN2. These control outputs can be used for controlling
external voltage switches to enabled/disable voltage outputs.
Add support of these control outputs through regulator framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Clear the sleep/warm reset bits when it is not selected through
regulator platform data. This will make sure that configuration
is inline with the platform data regardless of boot/POR
configuration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
commit 6d191a5fc7a969d972f1681e1c23781aecb06a61
(regulator: core: Don't defer probe if there's no DT binding for a supply)
Attempted to differentiate between regulator_get() with an actual
DT binding for the supply and when there is none to avoid unnecessary
deferal.
However, ret value supplied by regulator_dev_lookup() is being
ignored by regulator_get(). So, exit with the appropriate return value.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The same table can be used for multiple instance of pdev, so we don't need to
allocate memory for of_regulator_match table per pdev.
match->driver_data points to the corresponding entry of as3711_reg_info,
however it is not used in current code, thus this patch does not set
driver_data in the of_regulator_match table.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
pci_disable_device is called by a driver after it stops using the pci
function - e.g. during the removal of the driver. The current
implementation removes the architecture specific information of this
function such that even after a call to pci_enable_device the pci
function is no longer usable. Just remove pcibios_disable_device.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Disable pci on s390. Enable with pci=on.
Suggested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Access to pci config space via pci_ops should not fail silently.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If a pci load instruction fails the content of the register where the
data is stored is possibly unchanged. Fix the inline assembly wrapper
__pcilg to not return stale data. Additionally fix the callers of this
function who access uninitialized variables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Don't let pci_load and friends crash the kernel when called with
e.g. an invalid offset. Return -ENXIO instead.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use distinct (and hopefully sane) names for the pci instruction
wrappers.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Uninline pci related instruction wrappers to de-bloat the code:
add/remove: 15/0 grow/shrink: 2/24 up/down: 1326/-12628 (-11302)
This is especially useful for the inlined pci read and write functions
which are used all over the kernel. Also remove the unused __stpcifc
while at it.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use pcibios_add_device to do arch specific device initialization.
This function will be called during pci_bus_add_device.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Don't modify function handles to get a disabled handle - call
clp_disable_fh. With this change we also do no longer deconfigure
enabled functions.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use the debugfs to keep track of a pci function's status changes.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The hash used for mapping irq numbers to msi descriptors does not
utilize all buckets that were allocated. Fix this by using the same
value (computed by the number of bits used for the hash function) at
relevant places.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch adds the last breaking event address as parameter
for 31 bit compat program signal handlers as it is already
done for 64 bit programs.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If too many ccw requests are pre-build before a suspend/resume cycle
the device might not get enough memory to do path verification
during resume.
Requeue requests to the block device request queue on suspend and free
pre-build ccw requests.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Reorganize format IO requests and enable usage of PAV.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
cio_validate_subchannel is used to do some basic checks to find out
if it's worth to further investigate a subchannel. Move the allocation
and initialization of the subchannels locks to css_alloc_subchannel.
Clean up the functions involved while at it.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Via ccw_device_init_count we keep track of how many devices are in
asynchronous device recognition/initialization. For early devices this
variable was not only used prior to its initialization but used
incorrectly (incremented but never decremented). Fix this by using static
initialization for this variable (and friends), make them visible to
device.c only, and decrement the counter after recognition of early
devices is finished.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Make css_probe_device static and remove an unimplemented prototype.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use cio_register_early_subchannels to register early subchannels
which are already in use. Call this function before we do the
actual subchannel scanning loop. This helps us to get rid of some
more special cases regarding the console subchannel.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove the static console ccw device (and friends) and use dynamic
allocation for these structures. With this change the console
device is treated (mostly) like any other ccw device and we can
remove some special cases.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove the static console subchannel (and friends) and use dynamic
allocation for these structures. With this change the console
subchanel is treated (mostly) like any other subchannel and we can
remove some special cases.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Split the subchannel registration in device_initialize and device_add
and move the initialization part inside the allocation function. With
this change we can use refcounting during the complete lifespan of a
subchannel which is important for devices where we do the actually
registration at a later time.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
force_console is used to wake up the CCW based console device to
print a panic message in case something goes wrong in a suspend
or resume cycle. Stop using the static console_subchannel and add
a parameter to this function to specify which ccw device we have
to wake up.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
wait_cons_dev is used to busy wait for an interrupt on the console
ccw device. Stop using the static console_subchannel and add a
parameter to this function to specify on which ccw device/subchannel
we have to do the polling.
While at it rename the function to ccw_device_wait_idle and
move it to device.c
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Since commit 5f954c34 ([S390] hibernation: fix lowcore handling)
the absolute zero lowcore is lost during suspend/resume.
For example, this leads to the problem that the re-IPL device
for kdump is no longer set after resume.
With this patch during suspend a buffer is allocated in the new PM
notifier "suspend_pm_cb" and then the absolute zero lowcore is saved
to that buffer. The resume code then copies back this buffer to
absolute zero and afterwards the PM notifier releases the memory.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use BITS_TO_LONGS() instead of __BITOPS_WORDS() that is considered
to be private macro in asm/bitops.h for s390.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove unused __BITOPS_ALIGN, and replace __BITOPS_WORDSIZE with
BITS_PER_LONG.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use sske with multiple block control to initialize storage keys within
a 1 MB frame at once.
It turned out that the sske with mb=1 is an order of magnitude faster
than pfmf. This is only an issue for very large systems (several 100GB)
where storage key initialization could last more than a minute.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
dumpstack() did not always print a sane callchain when being called.
The reason is that show_trace() accessed register 15 directly to get
the current stack pointer and passed that pointer to __show_trace()
which expects a valid stack frame pointer as argument.
However due to tail call optimization the stack frame may not exist
anymore when __show_trace() gets called and therefore an invalid
stack frame pointer gets passed.
To prevent that disable tail call optimization for call chain walking
functions.
So move all the show_* functions to a dumpstack.c file like other
architectures have it already and add a -fno-optimize-sibling-calls
compile flag to both dumpstack.c and stacktrace.c to prevent tail
call optimization.
Fixes callchains that looked e.g. like this:
[ 12.868258] Call Trace:
[ 12.868262] ([<0000000000008000>] 0x8000)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Used PTR_RET function instead of IS_ERR and PTR_ERR.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Rewrote conditional statement and eliminated the out_kthread label.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
remove cast for kzalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Signed-off-by: Stelian Nirlu <steliannirlu@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Make use of the stored copy of format 1 channel-path data instead
of querying the information every time the corresponding function
is called.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
