| Age | Commit message (Collapse) | Author |
|---|
|
DSA is able to install FDB entries towards the CPU port for addresses
which were dynamically learnt by the software bridge on foreign
interfaces that are in the same bridge with a DSA switch interface.
Since this behavior is opportunistic, it is guarded by the
"assisted_learning_on_cpu_port" property which can be enabled by drivers
and is not done automatically (since certain switches may support
address learning of packets coming from the CPU port).
But if those FDB entries added on the foreign interfaces are static
(added by the user) instead of dynamically learnt, currently DSA does
not do anything (and arguably it should).
Because static FDB entries are not supposed to move on their own, there
is no downside in reusing the "assisted_learning_on_cpu_port" logic to
sync static FDB entries to the DSA CPU port unconditionally, even if
assisted_learning_on_cpu_port is not requested by the driver.
For example, this situation:
br0
/ \
swp0 dummy0
$ bridge fdb add 02:00:de:ad:00:01 dev dummy0 vlan 1 master static
Results in DSA adding an entry in the hardware FDB, pointing this
address towards the CPU port.
The same is true for entries added to the bridge itself, e.g:
$ bridge fdb add 02:00:de:ad:00:01 dev br0 vlan 1 self local
(except that right now, DSA still ignores 'local' FDB entries, this will
be changed in a later patch)
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the DSA master implements strict address filtering, then the unicast
and multicast addresses kept by the DSA CPU ports should be synchronized
with the address lists of the DSA master.
Note that we want the synchronization of the master's address lists even
if the DSA switch doesn't support unicast/multicast database operations,
on the premises that the packets will be flooded to the CPU in that
case, and we should still instruct the master to receive them. This is
why we do the dev_uc_add() etc first, even if dsa_port_notify() returns
-EOPNOTSUPP. In turn, dev_uc_add() and friends return error only if
memory allocation fails, so it is probably ok to check and propagate
that error code and not just ignore it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same concerns expressed for host MDB entries are valid for host FDBs
just as well:
- in the case of multiple bridges spanning the same switch chip, deleting
a host FDB entry that belongs to one bridge will result in breakage to
the other bridge
- not deleting FDB entries across DSA links means that the switch's
hardware tables will eventually run out, given enough wear&tear
So do the same thing and introduce reference counting for CPU ports and
DSA links using the same data structures as we have for MDB entries.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA treats some bridge FDB entries by trapping them to the CPU port.
Currently, the only class of such entries are FDB addresses learnt by
the software bridge on a foreign interface. However there are many more
to be added:
- FDB entries with the is_local flag (for termination) added by the
bridge on the user ports (typically containing the MAC address of the
bridge port)
- FDB entries pointing towards the bridge net device (for termination).
Typically these contain the MAC address of the bridge net device.
- Static FDB entries installed on a foreign interface that is in the
same bridge with a DSA user port.
The reason why a separate cross-chip notifier for host FDBs is justified
compared to normal FDBs is the same as in the case of host MDBs: the
cross-chip notifier matching function in switch.c should avoid
installing these entries on routing ports that route towards the
targeted switch, but not towards the CPU. This is required in order to
have proper support for H-like multi-chip topologies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ever since the cross-chip notifiers were introduced, the design was
meant to be simplistic and just get the job done without worrying too
much about dangling resources left behind.
For example, somebody installs an MDB entry on sw0p0 in this daisy chain
topology. It gets installed using ds->ops->port_mdb_add() on sw0p0,
sw1p4 and sw2p4.
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Then the same person deletes that MDB entry. The cross-chip notifier for
deletion only matches sw0p0:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
Why?
Because the DSA links are 'trunk' ports, if we just go ahead and delete
the MDB from sw1p4 and sw2p4 directly, we might delete those multicast
entries when they are still needed. Just consider the fact that somebody
does:
- add a multicast MAC address towards sw0p0 [ via the cross-chip
notifiers it gets installed on the DSA links too ]
- add the same multicast MAC address towards sw0p1 (another port of that
same switch)
- delete the same multicast MAC address from sw0p0.
At this point, if we deleted the MAC address from the DSA links, it
would be flooded, even though there is still an entry on switch 0 which
needs it not to.
So that is why deletions only match the targeted source port and nothing
on DSA links. Of course, dangling resources means that the hardware
tables will eventually run out given enough additions/removals, but hey,
at least it's simple.
But there is a bigger concern which needs to be addressed, and that is
our support for SWITCHDEV_OBJ_ID_HOST_MDB. DSA simply translates such an
object into a dsa_port_host_mdb_add() which ends up as ds->ops->port_mdb_add()
on the upstream port, and a similar thing happens on deletion:
dsa_port_host_mdb_del() will trigger ds->ops->port_mdb_del() on the
upstream port.
When there are 2 VLAN-unaware bridges spanning the same switch (which is
a use case DSA proudly supports), each bridge will install its own
SWITCHDEV_OBJ_ID_HOST_MDB entries. But upon deletion, DSA goes ahead and
emits a DSA_NOTIFIER_MDB_DEL for dp->cpu_dp, which is shared between the
user ports enslaved to br0 and the user ports enslaved to br1. Not good.
The host-trapped multicast addresses installed by br1 will be deleted
when any state changes in br0 (IGMP timers expire, or ports leave, etc).
To avoid this, we could of course go the route of the zero-sum game and
delete the DSA_NOTIFIER_MDB_DEL call for dp->cpu_dp. But the better
design is to just admit that on shared ports like DSA links and CPU
ports, we should be reference counting calls, even if this consumes some
dynamic memory which DSA has traditionally avoided. On the flip side,
the hardware tables of switches are limited in size, so it would be good
if the OS managed them properly instead of having them eventually
overflow.
To address the memory usage concern, we only apply the refcounting of
MDB entries on ports that are really shared (CPU ports and DSA links)
and not on user ports. In a typical single-switch setup, this means only
the CPU port (and the host MDB entries are not that many, really).
The name of the newly introduced data structures (dsa_mac_addr) is
chosen in such a way that will be reusable for host FDB entries (next
patch).
With this change, we can finally have the same matching logic for the
MDB additions and deletions, as well as for their host-trapped variants.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit abd49535c380 ("net: dsa: execute dsa_switch_mdb_add only for
routing port in cross-chip topologies") does a surprisingly good job
even for the SWITCHDEV_OBJ_ID_HOST_MDB use case, where DSA simply
translates a switchdev object received on dp into a cross-chip notifier
for dp->cpu_dp.
To visualize how that works, imagine the daisy chain topology below and
consider a SWITCHDEV_OBJ_ID_HOST_MDB object emitted on sw2p0. How does
the cross-chip notifier know to match on all the right ports (sw0p4, the
dedicated CPU port, sw1p4, an upstream DSA link, and sw2p4, another
upstream DSA link)?
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
The answer is simple: the dedicated CPU port of sw2p0 is sw0p4, and
dsa_routing_port returns the upstream port for all switches.
That is fine, but there are other topologies where this does not work as
well. There are trees with "H" topologies in the wild, where there are 2
or more switches with DSA links between them, but every switch has its
dedicated CPU port. For these topologies, it seems stupid for the neighbor
switches to install an MDB entry on the routing port, since these
multicast addresses are fundamentally different than the usual ones we
support (and that is the justification for this patch, to introduce the
concept of a termination plane multicast MAC address, as opposed to a
forwarding plane multicast MAC address).
For example, when a SWITCHDEV_OBJ_ID_HOST_MDB would get added to sw0p0,
without this patch, it would get treated as a regular port MDB on sw0p2
and it would match on the ports below (including the sw1p3 routing port).
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ x ] [ ] [ ] [ ]
With the patch, the host MDB notifier on sw0p0 matches only on the local
switch, which is what we want for a termination plane address.
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ ] [ ] [ ] [ ]
Name this new matching function "dsa_switch_host_address_match" since we
will be reusing it soon for host FDB entries as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the new cross-chip notifiers for host addresses,
let's introduce some more topology helpers which we are going to use to
discern switches that are in our path towards the dedicated CPU port
from switches that aren't.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to add reference counting for FDB entries in cross-chip
topologies, and in order for that to have any chance of working and not
be unbalanced (leading to entries which are never deleted), we need to
ensure that higher layers are sane, because if they aren't, it's garbage
in, garbage out.
For example, if we add a bridge FDB entry twice, the bridge properly
errors out:
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
RTNETLINK answers: File exists
However, the same thing cannot be said about the bridge bypass
operations:
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ echo $?
0
But one 'bridge fdb del' is enough to remove the entry, no matter how
many times it was added.
The bridge bypass operations are impossible to maintain in these
circumstances and lack of support for reference counting the cross-chip
notifiers is holding us back from making further progress, so just drop
support for them. The only way left for users to install static bridge
FDB entries is the proper one, using the "master static" flags.
With this change, rtnl_fdb_add() falls back to calling
ndo_dflt_fdb_add() which uses the duplicate-exclusive variant of
dev_uc_add(): dev_uc_add_excl(). Because DSA does not (yet) declare
IFF_UNICAST_FLT, this results in us going to promiscuous mode:
$ bridge fdb add dev swp0 00:01:02:03:04:05
[ 28.206743] device swp0 entered promiscuous mode
$ bridge fdb add dev swp0 00:01:02:03:04:05
RTNETLINK answers: File exists
So even if it does not completely fail, there is at least some indication
that it is behaving differently from before, and closer to user space
expectations, I would argue (the lack of a "local|static" specifier
defaults to "local", or "host-only", so dev_uc_add() is a reasonable
default implementation). If the generic implementation of .ndo_fdb_add
provided by Vlad Yasevich is a proof of anything, it only proves that
the implementation provided by DSA was always wrong, by not looking at
"ndm->ndm_state & NUD_NOARP" (the "static" flag which means that the FDB
entry points outwards) and "ndm->ndm_state & NUD_PERMANENT" (the "local"
flag which means that the FDB entry points towards the host). It all
used to mean the same thing to DSA.
Update the documentation so that the users are not confused about what's
going on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a port joins a bridge which already has local FDB entries pointing
to the bridge device itself, we would like to offload those, so allow
the "dev" argument to be equal to the bridge too. The code already does
what we need in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Treat addresses added to the bridge itself in the same way as regular
ports and send out a notification so that drivers may sync it down to
the hardware FDB.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Annotate the writer side of fdb->dst:
- fdb_create()
- br_fdb_update()
- fdb_add_entry()
- br_fdb_external_learn_add()
with WRITE_ONCE() and the reader side:
- br_fdb_test_addr()
- br_fdb_update()
- fdb_fill_info()
- fdb_add_entry()
- fdb_delete_by_addr_and_port()
- br_fdb_external_learn_add()
- br_switchdev_fdb_notify()
with compiler barriers such that the readers do not attempt to reload
fdb->dst multiple times, leading to potentially different destination
ports when the fdb entry is updated concurrently.
This is especially important in read-side sections where fdb->dst is
used more than once, but let's convert all accesses for the sake of
uniformity.
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All internal use cases for tracepoint_probe_register() is set to not ever
be called with the same function and data. If it is, it is considered a
bug, as that means the accounting of handling tracepoints is corrupted.
If the function and data for a tracepoint is already registered when
tracepoint_probe_register() is called, it will call WARN_ON_ONCE() and
return with EEXISTS.
The BPF system call can end up calling tracepoint_probe_register() with
the same data, which now means that this can trigger the warning because
of a user space process. As WARN_ON_ONCE() should not be called because
user space called a system call with bad data, there needs to be a way to
register a tracepoint without triggering a warning.
Enter tracepoint_probe_register_may_exist(), which can be called, but will
not cause a WARN_ON() if the probe already exists. It will still error out
with EEXIST, which will then be sent to the user space that performed the
BPF system call.
This keeps the previous testing for issues with other users of the
tracepoint code, while letting BPF call it with duplicated data and not
warn about it.
Link: https://lore.kernel.org/lkml/20210626135845.4080-1-penguin-kernel@I-love.SAKURA.ne.jp/
Link: https://syzkaller.appspot.com/bug?id=41f4318cf01762389f4d1c1c459da4f542fe5153
Cc: stable@vger.kernel.org
Fixes: c4f6699dfcb85 ("bpf: introduce BPF_RAW_TRACEPOINT")
Reported-by: syzbot <syzbot+721aa903751db87aa244@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot+721aa903751db87aa244@syzkaller.appspotmail.com
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
MT8195 mmc host IP is compatible with MT8183, and currently it shows:
properties:
compatible:
oneOf:
...
- items:
- const: mediatek,mt8192-mmc
- const: mediatek,mt8195-mmc
- const: mediatek,mt8183-mmc
which means the compatible string in the device tree would be:
compatible = "mediatek,mt8192-mmc", "mediatek,mt8195-mmc",
"mediatek,mt8183-mmc";
The bindings is wrong and that isn't the result we want.
instead we want:
properties:
compatible:
oneOf:
...
- items:
- const: mediatek,mt8192-mmc
- const: mediatek,mt8183-mmc
- items:
- const: mediatek,mt8195-mmc
- const: mediatek,mt8183-mmc
which would give us:
compatible = "mediatek,mt8192-mmc", "mediatek,mt8183-mmc";
and
compatible = "mediatek,mt8195-mmc", "mediatek,mt8183-mmc";
Fixes: eb9cb7227e5c (dt-bindings: mmc: Add compatible for Mediatek MT8195)
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1623726033-16073-2-git-send-email-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When DMA-mapping of the bounce buffer fails, the driver tries to fall
back, but it leaves the allocated host->bounce_buffer although its
size is zero. Later on, the driver checks the use of bounce buffer
with host->bounce_buffer pointer, and it tries to use the buffer
incorrectly, resulting in Oops.
This patch clears the release the unused buffer and clears the
bounce_buffer pointer for addressing the problem.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210611101948.18972-1-tiwai@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since the EMMC clock was changed from 200Mhz to 175Mhz in FIP,
there were some warnings introduced, as the frequency values
being checked was still wrt 200Mhz in code. Hence, the frequency
checks are now updated based on the current 175Mhz EMMC clock changed
in FIP.
Spamming kernel log msg:
"phy phy-20290000.mmc_phy.2: Unsupported rate: 43750000"
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210603182242.25733-3-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If clock-frequency property is set and it is not the same as the current
clock rate of clk_xin(base clock frequency), set clk_xin to use the
provided clock rate.
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/20210603182242.25733-2-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
* pm-domains:
PM: domains: Drop/restore performance state votes for devices at runtime PM
PM: domains: Return early if perf state is already set for the device
PM: domains: Split code in dev_pm_genpd_set_performance_state()
PM: domains: fix some kernel-doc issues
* pm-devfreq:
PM / devfreq: passive: Fix get_target_freq when not using required-opp
dt-bindings: devfreq: tegra30-actmon: Add cooling-cells
dt-bindings: devfreq: tegra30-actmon: Convert to schema
PM / devfreq: userspace: Use DEVICE_ATTR_RW macro
PM / devfreq: imx8m-ddrc: Remove DEVFREQ_GOV_SIMPLE_ONDEMAND dependency
PM / devfreq: tegra30: Support thermal cooling
PM / devfreq: imx-bus: Remove imx_bus_get_dev_status
PM / devfreq: Add missing error code in devfreq_add_device()
|
|
* pm-cpufreq:
cpufreq: Make cpufreq_online() call driver->offline() on errors
cpufreq: loongson2: Remove unused linux/sched.h headers
cpufreq: sh: Remove unused linux/sched.h headers
cpufreq: stats: Clean up local variable in cpufreq_stats_create_table()
cpufreq: intel_pstate: hybrid: Fix build with CONFIG_ACPI unset
cpufreq: sc520_freq: add 'fallthrough' to one case
cpufreq: intel_pstate: Add Cometlake support in no-HWP mode
cpufreq: intel_pstate: Add Icelake servers support in no-HWP mode
cpufreq: intel_pstate: hybrid: CPU-specific scaling factor
cpufreq: intel_pstate: hybrid: Avoid exposing two global attributes
* pm-cpuidle:
cpuidle: teo: remove unneeded semicolon in teo_select()
cpuidle: teo: Use kerneldoc documentation in admin-guide
cpuidle: teo: Rework most recent idle duration values treatment
cpuidle: teo: Change the main idle state selection logic
cpuidle: teo: Cosmetic modification of teo_select()
cpuidle: teo: Cosmetic modifications of teo_update()
intel_idle: Adjust the SKX C6 parameters if PC6 is disabled
|
|
* pm-core:
PM: runtime: Clarify documentation when callbacks are unassigned
PM: runtime: Allow unassigned ->runtime_suspend|resume callbacks
PM: runtime: Improve path in rpm_idle() when no callback
PM: runtime: document common mistake with pm_runtime_get_sync()
* pm-sleep:
PM: hibernate: remove leading spaces before tabs
PM: sleep: remove trailing spaces and tabs
PM: hibernate: fix spelling mistakes
PM: wakeirq: Set IRQF_NO_AUTOEN when requesting the IRQ
|
|
* pm-opp:
opp: Allow required-opps to be used for non genpd use cases
opp: use list_del_init instead of list_del/INIT_LIST_HEAD
|
|
* acpi-ec:
ACPI: EC: trust DSDT GPE for certain HP laptop
ACPI: EC: Make more Asus laptops use ECDT _GPE
* acpi-apei:
ACPI: APEI: fix synchronous external aborts in user-mode
ACPI: APEI: Don't warn if ACPI is disabled
* acpi-soc:
ACPI: LPSS: Use kstrtol() instead of simple_strtol()
* acpi-misc:
ACPI: NVS: fix doc warnings in nvs.c
ACPI: NUMA: fix typo in a comment
ACPI: OSL: Use DEFINE_RES_IO_NAMED() to simplify code
ACPI: bus: Call kobject_put() in acpi_init() error path
ACPI: bus: Remove unneeded assignment
ACPI: configfs: Replace ACPI_INFO() with pr_debug()
ACPI: ipmi: Remove address space handler in error path
ACPI: event: Remove redundant initialization of local variable
ACPI: sbshc: Fix fall-through warning for Clang
|
|
* acpi-dptf:
ACPI: DPTF: Add battery participant for Intel SoCs
* acpi-messages:
ACPI: Remove the macro PREFIX "ACPI: "
ACPI: sleep: Unify the message printing
ACPI: sbs: Unify the message printing
ACPI: scan: Unify the log message printing
ACPI: sbshc: Unify the message printing
ACPI: sysfs: Cleanup message printing
ACPI: reboot: Unify the message printing
ACPI: processor_throttling: Cleanup the printing messages
ACPI: processor_perflib: Cleanup print messages
ACPI: processor_thermal: Remove unused PREFIX for printing
ACPI: pci_root: Unify the message printing
ACPI: osl: Remove the duplicated PREFIX for message printing
ACPI: nvs: Unify the message printing
ACPI: glue: Clean up the printing messages
ACPI: event: Use pr_*() macros to replace printk()
ACPI: bus: Use pr_*() macros to replace printk()
ACPI: blacklist: Unify the message printing
ACPI: cmos_rtc: Using pr_fmt() and remove PREFIX
|
|
* acpi-prm:
ACPI: PRM: make symbol 'prm_module_list' static
ACPI: Add \_SB._OSC bit for PRM
ACPI: PRM: implement OperationRegion handler for the PlatformRtMechanism subtype
* acpi-sysfs:
ACPI: sysfs: Remove tailing return statement in void function
ACPI: sysfs: Use __ATTR_RO() and __ATTR_RW() macros
ACPI: sysfs: Sort headers alphabetically
ACPI: sysfs: Refactor param_get_trace_state() to drop dead code
ACPI: sysfs: Unify pattern of memory allocations
ACPI: sysfs: Allow bitmap list to be supplied to acpi_mask_gpe
ACPI: sysfs: Make sparse happy about address space in use
ACPI: sysfs: fix doc warnings in device_sysfs.c
ACPI: sysfs: Drop four redundant return statements
ACPI: sysfs: Fix a buffer overrun problem with description_show()
* acpi-x86:
x86/acpi: Switch to pr_xxx log functions
|
|
* acpi-pm:
ACPI: PM: postpone bringing devices to D0 unless we need them
ACPI: PM: Adjust behavior for field problems on AMD systems
ACPI: PM: s2idle: Add support for new Microsoft UUID
ACPI: PM: s2idle: Add support for multiple func mask
ACPI: PM: s2idle: Refactor common code
ACPI: PM: s2idle: Use correct revision id
ACPI: power: Use dev_dbg() to print some messages
ACPI: sleep: Fix acpi_pm_pre_suspend() kernel-doc
ACPI: power: Rework turning off unused power resources
ACPI: power: Save the last known state of each power resource
ACPI: power: Use u8 as the power resource state data type
ACPI: PM / fan: Put fan device IDs into separate header file
ACPI: PM: s2idle: Add missing LPS0 functions for AMD
* acpi-processor:
ACPI: processor_throttling: Fix several coding style issues
ACPI: processor_throttling: Remove redundant initialization of 'obj'
ACPI: processor idle: Fix up C-state latency if not ordered
* acpi-resources:
ACPI: resources: Add checks for ACPI IRQ override
|
|
* acpi-bus:
ACPI: Remove redundant clearing of context->ret.pointer from acpi_run_osc()
* acpi-scan:
ACPI: scan: Simplify acpi_table_events_fn()
ACPI: scan: Fix race related to dropping dependencies
ACPI: scan: Reorganize acpi_device_add()
ACPI: scan: Fix device object rescan in acpi_scan_clear_dep()
ACPI: scan: Make acpi_walk_dep_device_list()
ACPI: scan: Rearrange acpi_dev_get_first_consumer_dev_cb()
ACPI: scan: Define acpi_bus_put_acpi_device() as static inline
ACPI: scan: initialize local variable to avoid garbage being returned
ACPI: scan: Add function to fetch dependent of ACPI device
ACPI: scan: Extend acpi_walk_dep_device_list()
ACPI: scan: Rearrange dep_unmet initialization
* acpi-tables:
ACPI: tables: Add custom DSDT file as makefile prerequisite
ACPI: bgrt: Use sysfs_emit
ACPI: bgrt: Fix CFI violation
ACPI: tables: FPDT: Add missing acpi_put_table() in acpi_init_fpdt()
ACPI: tables: PPTT: Populate cache-id if provided by firmware
|
|
* acpica:
ACPICA: Add PRMT module header to facilitate parsing
ACPICA: Update version to 20210604
ACPICA: Add support for PlatformRtMechanism OperationRegion handler
ACPICA: iASL: add disassembler support for PRMT
ACPICA: Add the CFMWS structure definition to the CEDT table
ACPICA: Add defines for the CXL Host Bridge Structure (CHBS)
ACPICA: iASL: Add support for the BDAT ACPI table
ACPICA: Add _PLD panel positions
ACPICA: Use ACPI_FALLTHROUGH
ACPICA: iASL Table Compiler: Add full support for RGRT ACPI table
ACPICA: iASL: Add support for the SVKL table
ACPICA: iASL: Finish support for the IVRS ACPI table
ACPICA: Fix memory leak caused by _CID repair function
ACPICA: Add SVKL table headers
ACPICA: ACPI 6.4: MADT: add Multiprocessor Wakeup Mailbox Structure
|
|
ll_new_hw_segment() is reached only in case of single range discard
merge, and we don't have max discard segment size limit actually, so
it is wrong to run the following check:
if (req->nr_phys_segments + nr_phys_segs > blk_rq_get_max_segments(req))
it may be always false since req->nr_phys_segments is initialized as
one, and bio's segment count is still 1, blk_rq_get_max_segments(reg)
is 1 too.
Fix the issue by not doing the check and bypassing the calculation of
discard request's nr_phys_segments.
Based on analysis from Wang Shanker.
Cc: Christoph Hellwig <hch@lst.de>
Reported-by: Wang Shanker <shankerwangmiao@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210628023312.1903255-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) framework updates for v5.14
from Viresh Kumar:
"This pull request:
- allows partial use of required-opps for non-genpd users.
- does a minor cleanup and uses list_del_init()."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Allow required-opps to be used for non genpd use cases
opp: use list_del_init instead of list_del/INIT_LIST_HEAD
|
|
Split __gfs2_unstuff_inode off from gfs2_unstuff_dinode and clean up the
code a little. All remaining callers now pass NULL as the page argument
of gfs2_unstuff_dinode, so remove that argument.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
In gfs2_page_mkwrite, unstuff inodes before locking the page. That
way, we won't have to pass in the locked page to gfs2_unstuff_inode,
and gfs2_unstuff_inode can look up and lock the page itself.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
We're setting an error number so that block_page_mkwrite_return
translates it into the corresponding VM_FAULT_* code in several places,
but this is getting confusing, so set the VM_FAULT_* codes directly
instead. (No change in functionality.)
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Clang's integrated assembler only accepts these instructions when the
cpu is set to mips32r5. With this change, we can assemble
malta_defconfig with Clang via `make LLVM_IAS=1`.
Link: https://github.com/ClangBuiltLinux/linux/issues/763
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The cause of the problem is as follows:
1. when cat /sys/devices/system/memory/memory0/valid_zones,
test_pages_in_a_zone() will be called.
2. test_pages_in_a_zone() finds the zone according to stat_pfn = 0.
The smallest pfn of the numa node in the mips architecture is 128,
and the page corresponding to the previous 0~127 pfn is not
initialized (page->flags is 0xFFFFFFFF)
3. The nid and zonenum obtained using page_zone(pfn_to_page(0)) are out
of bounds in the corresponding array,
&NODE_DATA(page_to_nid(page))->node_zones[page_zonenum(page)],
access to the out-of-bounds zone member variables appear abnormal,
resulting in Oops.
Therefore, it is necessary to keep the page between 0 and the minimum
pfn to prevent Oops from appearing.
Signed-off-by: zhanglianjie <zhanglianjie@uniontech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
MIPS MT extensions were added with the MIPS 34K processor, which was
based on the MIPS32r2 ISA.
This fixes a build error when building a generic kernel for a MIPS32r1
CPU.
Fixes: c434b9f80b09 ("MIPS: Kconfig: add MIPS_GENERIC_KERNEL symbol")
Cc: stable@vger.kernel.org # v5.9
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
|
|
|
|
|
|
Add support for divider specific read only CCF flag
(CLK_DIVIDER_READ_ONLY).
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lore.kernel.org/r/20210628070122.26217-5-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Use ZynqMP specific mux clock flags instead of using CCF flags.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lore.kernel.org/r/20210628070122.26217-4-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Use ZynqMP specific divider clock flags instead of using CCF flags.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lore.kernel.org/r/20210628070122.26217-3-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Currently firmware passes CCF specific flags to ZynqMP clock driver.
So firmware needs to be updated if CCF flags are changed. The firmware
should have its own 'flag number space' that is distinct from the
common clk framework's 'flag number space'. So define and use ZynqMP
specific common clock flags instead of using CCF flags.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lore.kernel.org/r/20210628070122.26217-2-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Presumably we want to use this match table so add a module device table
and set the driver match pointer appropriately.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Liam Beguin <lvb@xiphos.com>
Fixes: 3bc61cfd6f4a ("clk: add support for the lmk04832")
Link: https://lore.kernel.org/r/20210629060751.3119453-2-sboyd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This driver depends on SPI. Otherwise compilation fails
clk-lmk04832.c:(.text+0x1668): undefined reference to `spi_get_device_id'
Reported-by: kernel test robot <lkp@intel.com>
Cc: Liam Beguin <lvb@xiphos.com>
Fixes: 3bc61cfd6f4a ("clk: add support for the lmk04832")
Link: https://lore.kernel.org/r/20210629060751.3119453-1-sboyd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace rlimit handling update from Eric Biederman:
"This is the work mainly by Alexey Gladkov to limit rlimits to the
rlimits of the user that created a user namespace, and to allow users
to have stricter limits on the resources created within a user
namespace."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
cred: add missing return error code when set_cred_ucounts() failed
ucounts: Silence warning in dec_rlimit_ucounts
ucounts: Set ucount_max to the largest positive value the type can hold
kselftests: Add test to check for rlimit changes in different user namespaces
Reimplement RLIMIT_MEMLOCK on top of ucounts
Reimplement RLIMIT_SIGPENDING on top of ucounts
Reimplement RLIMIT_MSGQUEUE on top of ucounts
Reimplement RLIMIT_NPROC on top of ucounts
Use atomic_t for ucounts reference counting
Add a reference to ucounts for each cred
Increase size of ucounts to atomic_long_t
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull array-bounds fixes from Gustavo Silva:
"Fix an out-of-bounds warning in the media subsystem.
This is part of the ongoing efforts to globally enable -Warray-bounds"
* tag 'array-bounds-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
media: siano: Fix out-of-bounds warnings in smscore_load_firmware_family2()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo Silva:
"Fix many fall-through warnings when building with Clang 12.0.0 and
'-Wimplicit-fallthrough' so that we at some point will be able to
enable that warning by default"
* tag 'fallthrough-fixes-clang-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (26 commits)
rxrpc: Fix fall-through warnings for Clang
drm/nouveau/clk: Fix fall-through warnings for Clang
drm/nouveau/therm: Fix fall-through warnings for Clang
drm/nouveau: Fix fall-through warnings for Clang
xfs: Fix fall-through warnings for Clang
xfrm: Fix fall-through warnings for Clang
tipc: Fix fall-through warnings for Clang
sctp: Fix fall-through warnings for Clang
rds: Fix fall-through warnings for Clang
net/packet: Fix fall-through warnings for Clang
net: netrom: Fix fall-through warnings for Clang
ide: Fix fall-through warnings for Clang
hwmon: (max6621) Fix fall-through warnings for Clang
hwmon: (corsair-cpro) Fix fall-through warnings for Clang
firewire: core: Fix fall-through warnings for Clang
braille_console: Fix fall-through warnings for Clang
ipv4: Fix fall-through warnings for Clang
qlcnic: Fix fall-through warnings for Clang
bnxt_en: Fix fall-through warnings for Clang
netxen_nic: Fix fall-through warnings for Clang
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Use normal block device I/O path for pstore/blk. (Christoph Hellwig,
Kees Cook, Pu Lehui)"
* tag 'pstore-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/blk: Include zone in pstore_device_info
pstore/blk: Fix kerndoc and redundancy on blkdev param
pstore/blk: Use the normal block device I/O path
pstore/blk: Move verify_size() macro out of function
pstore/blk: Improve failure reporting
|
