| Age | Commit message (Collapse) | Author |
|---|
|
Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
remaining issues with the reset adapter logic in igc_tsn_offload_apply()
have been observed:
1. The reset adapter logics for i225 and i226 differ, although they should
be the same according to the guidelines in I225/6 HW Design Section
7.5.2.1 on software initialization during tx mode changes.
2. The i225 resets adapter every time, even though tx mode doesn't change.
This occurs solely based on the condition igc_is_device_id_i225() when
calling schedule_work().
3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
resets adapter for legacy->tsn tx mode transitions.
4. qbv_count introduced in the patch is actually not needed; in this
context, a non-zero value of qbv_count is used to indicate if tx mode
was unconditionally set to tsn in igc_tsn_enable_offload(). This could
be replaced by checking the existing register
IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.
This patch resolves all issues and enters schedule_work() to reset the
adapter only when changing tx mode. It also removes reliance on qbv_count.
qbv_count field will be removed in a future patch.
Test ran:
1. Verify reset adapter behaviour in i225/6:
a) Enrol a new GCL
Reset adapter observed (tx mode change legacy->tsn)
b) Enrol a new GCL without deleting qdisc
No reset adapter observed (tx mode remain tsn->tsn)
c) Delete qdisc
Reset adapter observed (tx mode change tsn->legacy)
2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
to confirm it remains resolved.
Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When user issues these cmds:
1. Either a) or b)
a) mqprio with hardware offload disabled
b) taprio with txtime-assist feature enabled
2. etf
3. tc qdisc delete
4. taprio with base time in the past
At step 4, qbv_config_change_errors wrongly increased by 1.
Excerpt from IEEE 802.1Q-2018 8.6.9.3.1:
"If AdminBaseTime specifies a time in the past, and the current schedule
is running, then: Increment ConfigChangeError counter"
qbv_config_change_errors should only increase if base time is in the past
and no taprio is active. In user perspective, taprio was not active when
first triggered at step 4. However, i225/6 reuses qbv for etf, so qbv is
enabled with a dummy schedule at step 2 where it enters
igc_tsn_enable_offload() and qbv_count got incremented to 1. At step 4, it
enters igc_tsn_enable_offload() again, qbv_count is incremented to 2.
Because taprio is running, tc_setup_type is TC_SETUP_QDISC_ETF and
qbv_count > 1, qbv_config_change_errors value got incremented.
This issue happens due to reliance on qbv_count field where a non-zero
value indicates that taprio is running. But qbv_count increases
regardless if taprio is triggered by user or by other tsn feature. It does
not align with qbv_config_change_errors expectation where it is only
concerned with taprio triggered by user.
Fixing this by relocating the qbv_config_change_errors logic to
igc_save_qbv_schedule(), eliminating reliance on qbv_count and its
inaccuracies from i225/6's multiple uses of qbv feature for other TSN
features.
The new function created: igc_tsn_is_taprio_activated_by_user() uses
taprio_offload_enable field to indicate that the current running taprio
was triggered by user, instead of triggered by non-qbv feature like etf.
Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Testing uncovered that even when the taprio gate is closed, some packets
still transmit.
According to i225/6 hardware errata [1], traffic might overflow the
planned QBV window. This happens because MAC maintains an internal buffer,
primarily for supporting half duplex retries. Therefore, even when the
gate closes, residual MAC data in the buffer may still transmit.
To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes
to the recommended 88 bytes by modifying the RETX_CTL register value.
This follows guidelines from:
[1] Ethernet Controller I225/I22 Spec Update Rev 2.1 Errata Item 9:
TSN: Packet Transmission Might Cross Qbv Window
[2] I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control
Note that the RETX_CTL register can't be used in TSN mode because half
duplex feature cannot coexist with TSN.
Test Steps:
1. Send taprio cmd to board A:
tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 4 \
map 3 2 1 0 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time 0 \
sched-entry S 0x07 500000 \
sched-entry S 0x0f 500000 \
flags 0x2 \
txtime-delay 0
Note that for TC3, gate should open for 500us and close for another
500us.
3. Take tcpdump log on Board B.
4. Send udp packets via UDP tai app from Board A to Board B.
5. Analyze tcpdump log via wireshark log on Board B. Ensure that the
total time from the first to the last packet received during one cycle
for TC3 does not exceed 500us.
Fixes: 43546211738e ("igc: Add new device ID's")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When avc_add_xperms_decision() fails, the information recorded by the new
avc node is incomplete. In this case, the new avc node should be released
instead of replacing the old avc node.
Cc: stable@vger.kernel.org
Fixes: fa1aa143ac4a ("selinux: extended permissions for ioctls")
Suggested-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
The ID register for S1PIE is ID_AA64MMFR3_EL1.S1PIE which is bits 11:8 but
get-reg-list uses a shift of 4, checking SCTLRX instead. Use a shift of 8
instead.
Fixes: 5f0419a0083b ("KVM: selftests: get-reg-list: add Permission Indirection registers")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240731-kvm-arm64-fix-s1pie-test-v1-1-a9253f3b7db4@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
Tidy up some of the PAuth trapping code to clear up some comments
and avoid clang/checkpatch warnings. Also, don't bother setting
PAuth HCR_EL2 bits in pKVM, since it's handled by the hypervisor.
Signed-off-by: Fuad Tabba <tabba@google.com>
Link: https://lore.kernel.org/r/20240722163311.1493879-1-tabba@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
In case the guest doesn't have any LPI, we previously relied on the
iterator setting
'intid = nr_spis + VGIC_NR_PRIVATE_IRQS' && 'lpi_idx = 1'
to exit the iterator. But it was broken with commit 85d3ccc8b75b ("KVM:
arm64: vgic-debug: Use an xarray mark for debug iterator") -- the intid
remains at 'nr_spis + VGIC_NR_PRIVATE_IRQS - 1', and we end up endlessly
printing the last SPI's state.
Consider that it's meaningless to search the LPI xarray and populate
lpi_idx when there is no LPI, let's just skip the process for that case.
The result is that
* If there's no LPI, we focus on the intid and exit the iterator when it
runs out of the valid SPI range.
* Otherwise we keep the current logic and let the xarray drive the
iterator.
Fixes: 85d3ccc8b75b ("KVM: arm64: vgic-debug: Use an xarray mark for debug iterator")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240807052024.2084-1-yuzenghui@huawei.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
With the NV support of TLBI-range operations, KVM makes use of
instructions that are only supported by binutils versions >= 2.30.
This breaks the build for very old toolchains.
Make KVM support conditional on having ARMv8.4 support in the
assembler, side-stepping the issue.
Fixes: 5d476ca57d7d ("KVM: arm64: nv: Add handling of range-based TLBI operations")
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Suggested-by: Arnd Bergmann <arnd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240807115144.3237260-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
The kernel can change spinlock behavior when running as a guest. But this
guest-friendly behavior causes performance problems on bare metal.
The kernel uses a static key to switch between the two modes.
In theory, the static key is enabled by default (run in guest mode) and
should be disabled for bare metal (and in some guests that want native
behavior or paravirt spinlock).
A performance drop is reported when running encode/decode workload and
BenchSEE cache sub-workload.
Bisect points to commit ce0a1b608bfc ("x86/paravirt: Silence unused
native_pv_lock_init() function warning"). When CONFIG_PARAVIRT_SPINLOCKS is
disabled the virt_spin_lock_key is incorrectly set to true on bare
metal. The qspinlock degenerates to test-and-set spinlock, which decreases
the performance on bare metal.
Set the default value of virt_spin_lock_key to false. If booting in a VM,
enable this key. Later during the VM initialization, if other
high-efficient spinlock is preferred (e.g. paravirt-spinlock), or the user
wants the native qspinlock (via nopvspin boot commandline), the
virt_spin_lock_key is disabled accordingly.
This results in the following decision matrix:
X86_FEATURE_HYPERVISOR Y Y Y N
CONFIG_PARAVIRT_SPINLOCKS Y Y N Y/N
PV spinlock Y N N Y/N
virt_spin_lock_key N Y/N Y N
Fixes: ce0a1b608bfc ("x86/paravirt: Silence unused native_pv_lock_init() function warning")
Reported-by: Prem Nath Dey <prem.nath.dey@intel.com>
Reported-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Suggested-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Suggested-by: Nikolay Borisov <nik.borisov@suse.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nikolay Borisov <nik.borisov@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240806112207.29792-1-yu.c.chen@intel.com
|
|
On a platform using the "Multiprocessor Wakeup Structure"[1] to startup
secondary CPUs the control processor needs to memremap() the physical
address of the MP Wakeup Structure mailbox to the variable
acpi_mp_wake_mailbox, which holds the virtual address of mailbox.
To wake up the AP the control processor writes the APIC ID of AP, the
wakeup vector and the ACPI_MP_WAKE_COMMAND_WAKEUP command into the mailbox.
Current implementation doesn't consider the case which restricts boot time
CPU bringup to 1 with the kernel parameter "maxcpus=1" and brings other
CPUs online later from user space as it sets acpi_mp_wake_mailbox to
read-only after init. So when the first AP is tried to brought online
after init, the attempt to update the variable results in a kernel panic.
The memremap() call that initializes the variable cannot be moved into
acpi_parse_mp_wake() because memremap() is not functional at that point in
the boot process. Also as the APs might never be brought up, keep the
memremap() call in acpi_wakeup_cpu() so that the operation only takes place
when needed.
Fixes: 24dd05da8c79 ("x86/apic: Mark acpi_mp_wake_* variables as __ro_after_init")
Signed-off-by: Zhiquan Li <zhiquan1.li@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/all/20240805103531.1230635-1-zhiquan1.li@intel.com
|
|
Commit ac21add2540e ("ice: Implement driver functionality to dump fec
statistics") introduces obtaining FEC correctable and uncorrectable
stats per netdev in ICE driver. Unfortunately the assignment of values
to fec_stats structure has been done incorrectly. This commit fixes the
assignments.
Fixes: ac21add2540e ("ice: Implement driver functionality to dump fec statistics")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Block HW write access for the driver while the device is in reset to
avoid potential race condition and access to the PTP HW in
non-nominal state which could lead to undesired effects
Fixes: 4aad5335969f ("ice: add individual interrupt allocation")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Synchronize OICR IRQ when preparing for reset to avoid potential
race conditions between the reset procedure and OICR
Fixes: 4aad5335969f ("ice: add individual interrupt allocation")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
_rtl92du_init_queue_reserved_page
GCC complains:
In file included from include/linux/ieee80211.h:21,
from include/net/mac80211.h:20,
from drivers/net/wireless/realtek/rtlwifi/rtl8192du/../wifi.h:14,
from drivers/net/wireless/realtek/rtlwifi/rtl8192du/hw.c:4:
In function 'u32p_replace_bits',
inlined from '_rtl92du_init_queue_reserved_page.isra' at drivers/net/wireless/realtek/rtlwifi/rtl8192du/hw.c:225:2:
>> include/linux/bitfield.h:189:18: warning: 'value32' is used uninitialized [-Wuninitialized]
Part of the variable is indeed left uninitialised.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408062100.DWhN0CYH-lkp@intel.com/
Fixes: e769c67105d3 ("wifi: rtlwifi: Add rtl8192du/hw.{c,h}")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/2a808244-93d0-492c-b304-ae1974df5df9@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix double inode unlock for direct IO sync writes (reported by
syzbot)
- fix root tree id/name map definitions, don't use fixed size buffers
for name (reported by -Werror=unterminated-string-initialization)
- fix qgroup reserve leaks in bufferd write path
- update scrub status structure more often so it can be reported in
user space more accurately and let 'resume' not repeat work
- in preparation to remove space cache v1 in the future print a warning
if it's detected
* tag 'for-6.11-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: avoid using fixed char array size for tree names
btrfs: fix double inode unlock for direct IO sync writes
btrfs: emit a warning about space cache v1 being deprecated
btrfs: fix qgroup reserve leaks in cow_file_range
btrfs: implement launder_folio for clearing dirty page reserve
btrfs: scrub: update last_physical after scrubbing one stripe
btrfs: factor out stripe length calculation into a helper
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"rt5033:
- fix driver regression causing kernel oops
axp288-charger:
- fix charge voltage setup
qcom-battmgr:
- fix thermal zone spamming errors
- fix init on Qualcomm X Elite"
* tag 'for-v6.11-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: qcom_battmgr: Ignore extra __le32 in info payload
power: supply: qcom_battmgr: return EAGAIN when firmware service is not up
power: supply: axp288_charger: Round constant_charge_voltage writes down
power: supply: axp288_charger: Fix constant_charge_voltage writes
power: supply: rt5033: Bring back i2c_set_clientdata
|
|
Currently, whenever a caller is providing an affinity hint for an
interrupt, the allocation code uses it to calculate the node and copies the
cpumask into irq_desc::affinity.
If the affinity for the interrupt is not marked 'managed' then the startup
of the interrupt ignores irq_desc::affinity and uses the system default
affinity mask.
Prevent this by setting the IRQD_AFFINITY_SET flag for the interrupt in the
allocator, which causes irq_setup_affinity() to use irq_desc::affinity on
interrupt startup if the mask contains an online CPU.
[ tglx: Massaged changelog ]
Fixes: 45ddcecbfa94 ("genirq: Use affinity hint in irqdesc allocation")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/all/20240806072044.837827-1-shayd@nvidia.com
|
|
So it turns out that we have to do two passes of
pti_clone_entry_text(), once before initcalls, such that device and
late initcalls can use user-mode-helper / modprobe and once after
free_initmem() / mark_readonly().
Now obviously mark_readonly() can cause PMD splits, and
pti_clone_pgtable() doesn't like that much.
Allow the late clone to split PMDs so that pagetables stay in sync.
[peterz: Changelog and comments]
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20240806184843.GX37996@noisy.programming.kicks-ass.net
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into arm/fixes
Devicetree fixes for TI K3 platforms for v6.11
Critical fixes for the following:
* j784s4: Fix for McASP DMA map
* J722s/AM62p: GPIO ranges fixes
* k3-am62-verdin-dahlia: sleep-moci fixes for deep-sleep (revert)
* tag 'ti-k3-dt-fixes-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arm64: dts: ti: k3-j784s4-main: Correct McASP DMAs
arm64: dts: ti: k3-j722s: Fix gpio-range for main_pmx0
arm64: dts: ti: k3-am62p: Fix gpio-range for main_pmx0
arm64: dts: ti: k3-am62p: Add gpio-ranges for mcu_gpio0
arm64: dts: ti: k3-am62-verdin-dahlia: Keep CTRL_SLEEP_MOCI# regulator on
arm64: dts: ti: k3-j784s4-evm: Consolidate serdes0 references
arm64: dts: ti: k3-j784s4-evm: Assign only lanes 0 and 1 to PCIe1
|
|
Commit f1d6588af93b tried to convert GPIO lookup tables to software
properties for the vbus gpio device, bit forgot the most important
step: actually attaching the new properties to the device.
Also fix up the name of the property array to reflect the board name,
and add missing gpio/property.h and devices.h includes absence of which
causes compile failures on some configurations.
Switch "#ifdef CONFIG_USB_PXA25X" to "#if IS_ENABLED(CONFIG_USB_PXA25X)"
because it should not matter if the driver is buolt in or a module, it
still need vbus controls.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f1d6588af93b ("ARM: pxa/gumstix: convert vbus gpio to use software nodes")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use double backticks instead of quotes for sysfs attribute value.
This makes sphinx generate the "mcu" and "cpu" values in monospace when
rendering to HTML.
Fixes: dfa556e45ae9 ("platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs")
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240730144924.25552-3-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix sphinx-build warnings
ERROR: Unexpected indentation.
WARNING: Block quote ends without a blank line; unexpected unindent
in Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/all/20240702174938.04c12aab@canb.auug.org.au/
Fixes: dfa556e45ae9 ("platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs")
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240730144924.25552-2-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Make the GPIO part of the driver optional, under a boolean config
option. Move the dependency to GPIOLIB and OF and the selection of
GPIOLIB_IRQCHIP to this new option.
This makes the turris-omnia-mcu driver available for compilation even if
GPIOLIB or OF are disabled.
Fixes: ed46f1f7731d ("platform: cznic: turris-omnia-mcu: fix Kconfig dependencies")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240719085756.30598-5-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Make the system poweroff and RTC wakeup part of the driver optional,
under a boolean config option. Move the dependency to RTC_CLASS to this
new option.
This makes the turris-omnia-mcu driver available for compilation even if
RTC_CLASS is disabled.
Fixes: ed46f1f7731d ("platform: cznic: turris-omnia-mcu: fix Kconfig dependencies")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240719085756.30598-4-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Make the TRNG part of the driver optional, under a boolean config
option.
This makes the driver turris-omnia-mcu available for compilation even if
HW_RANDOM is disabled.
Fixes: ed46f1f7731d ("platform: cznic: turris-omnia-mcu: fix Kconfig dependencies")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240719085756.30598-3-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Make the watchdog part of the driver optional, under a boolean config
option. Move the dependency to WATCHDOG to this new option, and change
the WATCHDOG_CORE dependency to selection, as is done in most watchdog
drivers.
This makes the turris-omnia-mcu driver available for compilation even if
WATCHDOG is disabled.
Fixes: ed46f1f7731d ("platform: cznic: turris-omnia-mcu: fix Kconfig dependencies")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240719085756.30598-2-kabel@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This fixes a device removal deadlock when using erasure coding.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
chasing down a device removal deadlock with erasure coding
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
We've had bugs in the past with incorrect integer conversions in disk
accounting code, which is why bucket helpers now always return s64s; add
a comment explaining this.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
implicit integer conversion is a fertile source of bugs, and we really
would rather not have the min()/max() macros doing it implicitly.
bcachefs appears to be the only place in the kernel where this happens,
so let's fix it.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
We won't find a contended lock if it's not being tracked.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
The return value uv_set_shared() and uv_remove_shared() (which are
wrappers around the share() function) is not always checked. The system
integrity of a protected guest depends on the Share and Unshare UVCs
being successful. This means that any caller that fails to check the
return value will compromise the security of the protected guest.
No code path that would lead to such violation of the security
guarantees is currently exercised, since all the areas that are shared
never get unshared during the lifetime of the system. This might
change and become an issue in the future.
The Share and Unshare UVCs can only fail in case of hypervisor
misbehaviour (either a bug or malicious behaviour). In such cases there
is no reasonable way forward, and the system needs to panic.
This patch replaces the return at the end of the share() function with
a panic, to guarantee system integrity.
Fixes: 5abb9351dfd9 ("s390/uv: introduce guest side ultravisor code")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20240801112548.85303-1-imbrenda@linux.ibm.com
Message-ID: <20240801112548.85303-1-imbrenda@linux.ibm.com>
[frankja@linux.ibm.com: Fixed up patch subject]
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
|
|
The function returns with the ppm_lock held if the PPM is
busy or there's an error.
Reported-and-tested-by: Luciano Coelho <luciano.coelho@intel.com>
Fixes: 5e9c1662a89b ("usb: typec: ucsi: rework command execution functions")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reported-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20240806112029.2984319-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
source capability message
Since commit (122968f8dda8 usb: typec: tcpm: avoid resets for missing
source capability messages), state will change from SNK_WAIT_CAPABILITIES
to SNK_WAIT_CAPABILITIES_TIMEOUT. We need to change SNK_WAIT_CAPABILITIES
-> SNK_READY path to SNK_WAIT_CAPABILITIES_TIMEOUT -> SNK_READY
accordingly. Otherwise, the sink port will never change to SNK_READY state
if the source does't have PD capability.
[ 503.547183] pending state change SNK_WAIT_CAPABILITIES -> SNK_WAIT_CAPABILITIES_TIMEOUT @ 310 ms [rev3 NONE_AMS]
[ 503.857239] state change SNK_WAIT_CAPABILITIES -> SNK_WAIT_CAPABILITIES_TIMEOUT [delayed 310 ms]
[ 503.857254] PD TX, header: 0x87
[ 503.862440] PD TX complete, status: 2
[ 503.862484] state change SNK_WAIT_CAPABILITIES_TIMEOUT -> SNK_UNATTACHED [rev3 NONE_AMS]
Fixes: 122968f8dda8 ("usb: typec: tcpm: avoid resets for missing source capability messages")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20240802064156.1846768-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ``alt`` parameter was used as a way to differentiate between
f->disable() and f->set_alt(). As the code paths diverge quite a bit,
pull out the f->disable() code from ffs_func_set_alt(), everything will
become clearer and less error prone. No change in functionality
intended.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240802140428.2000312-3-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The blamed commit made ffs_func_disable() always return -EINVAL as the
method calls ffs_func_set_alt() with the ``alt`` argument being
``(unsigned)-1``, which is always greater than MAX_ALT_SETTINGS.
Use the MAX_ALT_SETTINGS check just in the f->set_alt() code path,
f->disable() doesn't care about the ``alt`` parameter.
Make a surgical fix, but really the f->disable() code shall be pulled
out from ffs_func_set_alt(), the code will become clearer. A patch will
follow.
Note that ffs_func_disable() always returning -EINVAL made pixel6 crash
on USB disconnect.
Fixes: 2f550553e23c ("usb: gadget: f_fs: Add the missing get_alt callback")
Cc: stable <stable@kernel.org>
Reported-by: William McVicker <willmcvicker@google.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240802140428.2000312-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fix for 6.11-rc2
Here's a fix for an issue when using the usb_debug driver with Xen.
This change has been in linux-next for a couple of days with no reported
issues.
* tag 'usb-serial-6.11-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: debug: do not echo input by default
|
|
The kvm_hypercall() set for LoongArch is limited to a1-a5. So the
mention of a6 in the comment is undefined that needs to be rectified.
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Dandan Zhang <zhangdandan@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
1. "KVM_PRIVATE_MEM_SLOTS" is renamed as "KVM_INTERNAL_MEM_SLOTS".
2. "KVM_INTERNAL_MEM_SLOTS" defaults to zero, so it is not necessary to
define it in LoongArch's asm/kvm_host.h.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=bdd1c37a315bc50ab14066c4852bc8dcf070451e
Link: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b075450868dbc0950f0942617f222eeb989cad10
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
As very well explained in commit 20a004e7b017cce282 ("arm64: mm: Use
READ_ONCE/WRITE_ONCE when accessing page tables"), an architecture whose
page table walker can modify the PTE in parallel must use READ_ONCE()/
WRITE_ONCE() macro to avoid any compiler transformation.
So apply that to LoongArch which is such an architecture, in order to
avoid potential problems.
Similar to commit edf955647269422e ("riscv: Use accessors to page table
entries instead of direct dereference").
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
efi_shutdown_init() can register a general sys_off handler named
efi_power_off(). Enable this by providing efi_poweroff_required(),
like arm and x86. Since EFI poweroff is also supported on LoongArch,
and the enablement makes the poweroff function usable for hardwares
which lack ACPI S5.
We prefer ACPI poweroff rather than EFI poweroff (like x86), so we only
require EFI poweroff if acpi_gbl_reduced_hardware or acpi_no_s5 is true.
Cc: stable@vger.kernel.org
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Miao Wang <shankerwangmiao@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
In commit a78a8da51b36 ("drm/ttm: replace busy placement with flags v6"),
__i915_ttm_get_pages was updated to use flags instead of the separate
'busy' placement list. However, the behaviour was subtly changed.
Originally, the function would attempt to use the preferred placement
without eviction, and give an opportunity to restart the operation
before falling back to allowing eviction.
This was unintentionally changed, as the preferred placement was not
given the TTM_PL_FLAG_DESIRED flag, and so eviction could be triggered
in that first pass. This caused thrashing, and a significant performance
regression on DG2 systems with small BAR. For example, Minecraft and
Team Fortress 2 would drop to single-digit framerates.
Restore the original behaviour by marking the initial placement as
desired on that first attempt. Also, rework this to use a separate
struct ttm_palcement, as the individual placements are marked 'const',
so hot-patching the flags is even more dodgy than before.
Thanks to Justin Brewer for bisecting this.
Fixes: a78a8da51b36 ("drm/ttm: replace busy placement with flags v6")
Link: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11255
Signed-off-by: David Gow <david@davidgow.net>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240804091851.122186-3-david@davidgow.net
(cherry picked from commit 92653f2a572505adaf7f13f695c1907e71a1dc84)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
In commit a78a8da51b36 ("drm/ttm: replace busy placement with flags v6"),
the old system of having a separate placement list (for placements
which should be used without eviction) and a 'busy' placement list (for
placements which should be attempted if eviction is required) was
replaced with a new one where placements could be marked 'FALLBACK' (to
be attempted if eviction is required) or 'DESIRED' (to be attempted
first, but not if eviction is required).
i915 had always included the requested placement in the list of
'busy' placements: i.e., the placement could be used either if eviction
is required or not. But when the new system was put in place, the
requested (first) placement was marked 'DESIRED', so would never be used
if eviction became necessary. While a bug in the original commit
prevented this flag from working, when this was fixed in
4a0e7b3c ("drm/i915: fix applying placement flag"), it caused long hangs
on DG2 systems with small BAR.
Don't mark the requested placement DESIRED (or FALLBACK), allowing it to
be used in both situations. This matches the old behaviour, and resolves
the hangs.
Thanks to Justin Brewer for bisecting the issue.
Fixes: a78a8da51b36 ("drm/ttm: replace busy placement with flags v6")
Fixes: 4a0e7b3c3753 ("drm/i915: fix applying placement flag")
Link: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11255
Signed-off-by: David Gow <david@davidgow.net>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240804091851.122186-2-david@davidgow.net
(cherry picked from commit 54bf0af90844fbf18f5be3272eda69198dfdb622)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
The Framework Laptop 13 (Intel Core Ultra) has an ALC285 that ships in a
similar configuration to the ALC295 in previous models. It requires the
same quirk for headset detection.
Signed-off-by: Dustin L. Howett <dustin@howett.net>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20240806-alsa-hda-realtek-add-framework-laptop-13-intel-core-ultra-to-quirks-v1-1-42d6ce2dbf14@howett.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for MeiG Smart SRM825L which is based on Qualcomm 315 chip.
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2dee ProdID=4d22 Rev= 4.14
S: Manufacturer=MEIG
S: Product=LTE-A Module
S: SerialNumber=6f345e48
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: ZHANG Yuntian <yt@radxa.com>
Link: https://patch.msgid.link/D1EB81385E405DFE+20240803074656.567061-1-yt@radxa.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The wol variable in ksz_port_set_mac_address() is declared with random
data, but the code in ksz_get_wol call may not be executed so the
WAKE_MAGIC check may be invalid resulting in an error message when
setting a MAC address after starting the DSA driver.
Fixes: 3b454b6390c3 ("net: dsa: microchip: ksz9477: Add Wake on Magic Packet support")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240805235200.24982-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the missing geni_icc_disable() before return in
geni_i2c_runtime_resume().
Fixes: bf225ed357c6 ("i2c: i2c-qcom-geni: Add interconnect support")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The count increases only when a node is successfully added to
the linked list.
Cc: stable@vger.kernel.org
Fixes: fa1aa143ac4a ("selinux: extended permissions for ioctls")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
linkwatch_event() grabs possibly very contended RTNL mutex.
system_wq is not suitable for such work.
Inspired by many noisy syzbot reports.
3 locks held by kworker/0:7/5266:
#0: ffff888015480948 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3206 [inline]
#0: ffff888015480948 ((wq_completion)events){+.+.}-{0:0}, at: process_scheduled_works+0x90a/0x1830 kernel/workqueue.c:3312
#1: ffffc90003f6fd00 ((linkwatch_work).work){+.+.}-{0:0}, at: process_one_work kernel/workqueue.c:3207 [inline]
, at: process_scheduled_works+0x945/0x1830 kernel/workqueue.c:3312
#2: ffffffff8fa6f208 (rtnl_mutex){+.+.}-{3:3}, at: linkwatch_event+0xe/0x60 net/core/link_watch.c:276
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20240805085821.1616528-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
