| Age | Commit message (Collapse) | Author |
|---|
|
Currently if early_pgm_check_handler is called it ends up in pgm check
loop. The problem is that early_pgm_check_handler is instrumented by
KASAN but executed without DAT flag enabled which leads to addressing
exception when KASAN checks try to access shadow memory.
Fix that by executing early handlers with DAT flag on under KASAN as
expected.
Reported-and-tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
When single stepping an svc instruction on s390, the kernel is entered
with a PER program check interruption. The program check handler than
jumps to the system call handler by reloading the PSW. The code didn't
set GPR13 to the thread pointer in struct task_struct. This made the
kernel access invalid memory while trying to fetch the syscall function
address. Fix this by always assigned GPR13 after .Lsysc_per.
Fixes: 0b0ed657fe00 ("s390: remove critical section cleanup from entry.S")
Reported-and-tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Similar to the Kingston HyperX AMP, the Kingston HyperX Cloud
Alpha S (0951:0x16ea) uses two interfaces, but only the second
interface contains the capture stream. This patch delays the
registration until the second interface appears.
Signed-off-by: Christoffer Nielsen <cn@obviux.dk>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAOtG2YHOM3zy+ed9KS-J4HkZo_QGzcUG9MigSp4e4_-13r6B=Q@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove vcpu_vmx.host_pkru, which got left behind when PKRU support was
moved to common x86 code.
No functional change intended.
Fixes: 37486135d3a7b ("KVM: x86: Fix pkru save/restore when guest CR4.PKE=0, move it to x86.c")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200617034123.25647-1-sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The Linux TSC calibration procedure is subject to small variations
(its common to see +-1 kHz difference between reboots on a given CPU, for example).
So migrating a guest between two hosts with identical processor can fail, in case
of a small variation in calibrated TSC between them.
Without TSC scaling, the current kernel interface will either return an error
(if user_tsc_khz <= tsc_khz) or enable TSC catchup mode.
This change enables the following TSC tolerance check to
accept KVM_SET_TSC_KHZ within tsc_tolerance_ppm (which is 250ppm by default).
/*
* Compute the variation in TSC rate which is acceptable
* within the range of tolerance and decide if the
* rate being applied is within that bounds of the hardware
* rate. If so, no scaling or compensation need be done.
*/
thresh_lo = adjust_tsc_khz(tsc_khz, -tsc_tolerance_ppm);
thresh_hi = adjust_tsc_khz(tsc_khz, tsc_tolerance_ppm);
if (user_tsc_khz < thresh_lo || user_tsc_khz > thresh_hi) {
pr_debug("kvm: requested TSC rate %u falls outside tolerance [%u,%u]\n", user_tsc_khz, thresh_lo, thresh_hi);
use_scaling = 1;
}
NTP daemon in the guest can correct this difference (NTP can correct upto 500ppm).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Message-Id: <20200616114741.GA298183@fuller.cnet>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Only MSR address range 0x800 through 0x8ff is architecturally reserved
and dedicated for accessing APIC registers in x2APIC mode.
Fixes: 0105d1a52640 ("KVM: x2apic interface to lapic")
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-Id: <20200616073307.16440-1-xiaoyao.li@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix a typo in gue.h
Signed-off-by: Aiden Leong <aiden.leong@aibsd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In RFC 8684, we don't need to send sndr_key in SYN package anymore, so drop
it.
Fixes: cc7972ea1932 ("mptcp: parse and emit MP_CAPABLE option according to v1 spec")
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix check in ethtool_rx_flow_rule_create
Fixes: eca4205f9ec3 ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interface is being deleted, "/proc/net/dev_snmp6/<interface name>"
is deleted.
The function for this is addrconf_ifdown() in the addrconf_notify() and
it is called by notification, which is NETDEV_UNREGISTER.
But, if NETDEV_CHANGEMTU is triggered after NETDEV_UNREGISTER,
this proc file will be created again.
This recreated proc file will be deleted by netdev_wati_allrefs().
Before netdev_wait_allrefs() is called, creating a new HSR interface
routine can be executed and It tries to create a proc file but it will
find an un-deleted proc file.
At this point, it warns about it.
To avoid this situation, it can use ->dellink() instead of
->ndo_uninit() to release resources because ->dellink() is called
before NETDEV_UNREGISTER.
So, a proc file will not be recreated.
Test commands
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 mtu 1300
#SHELL1
while :
do
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
done
#SHELL2
while :
do
ip link del hsr0
done
Splat looks like:
[ 9888.980852][ T2752] proc_dir_entry 'dev_snmp6/hsr0' already registered
[ 9888.981797][ C2] WARNING: CPU: 2 PID: 2752 at fs/proc/generic.c:372 proc_register+0x2d5/0x430
[ 9888.981798][ C2] Modules linked in: hsr dummy veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6x
[ 9888.981814][ C2] CPU: 2 PID: 2752 Comm: ip Tainted: G W 5.8.0-rc1+ #616
[ 9888.981815][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 9888.981816][ C2] RIP: 0010:proc_register+0x2d5/0x430
[ 9888.981818][ C2] Code: fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 65 01 00 00 49 8b b5 e0 00 00 00 48 89 ea 40
[ 9888.981819][ C2] RSP: 0018:ffff8880628dedf0 EFLAGS: 00010286
[ 9888.981821][ C2] RAX: dffffc0000000008 RBX: ffff888028c69170 RCX: ffffffffaae09a62
[ 9888.981822][ C2] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f75ac
[ 9888.981823][ C2] RBP: ffff888028c693f4 R08: ffffed100d9401bd R09: ffffed100d9401bd
[ 9888.981824][ C2] R10: ffffffffaddf406f R11: 0000000000000001 R12: ffff888028c69308
[ 9888.981825][ C2] R13: ffff8880663584c8 R14: dffffc0000000000 R15: ffffed100518d27e
[ 9888.981827][ C2] FS: 00007f3876b3b0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[ 9888.981828][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 9888.981829][ C2] CR2: 00007f387601a8c0 CR3: 000000004101a002 CR4: 00000000000606e0
[ 9888.981830][ C2] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 9888.981831][ C2] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 9888.981832][ C2] Call Trace:
[ 9888.981833][ C2] ? snmp6_seq_show+0x180/0x180
[ 9888.981834][ C2] proc_create_single_data+0x7c/0xa0
[ 9888.981835][ C2] snmp6_register_dev+0xb0/0x130
[ 9888.981836][ C2] ipv6_add_dev+0x4b7/0xf60
[ 9888.981837][ C2] addrconf_notify+0x684/0x1ca0
[ 9888.981838][ C2] ? __mutex_unlock_slowpath+0xd0/0x670
[ 9888.981839][ C2] ? kasan_unpoison_shadow+0x30/0x40
[ 9888.981840][ C2] ? wait_for_completion+0x250/0x250
[ 9888.981841][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981842][ C2] ? dropmon_net_event+0x227/0x410
[ 9888.981843][ C2] ? notifier_call_chain+0x90/0x160
[ 9888.981844][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981845][ C2] notifier_call_chain+0x90/0x160
[ 9888.981846][ C2] register_netdevice+0xbe5/0x1070
[ ... ]
Reported-by: syzbot+1d51c8b74efa4c44adeb@syzkaller.appspotmail.com
Fixes: e0a4b99773d3 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove support for context switching between the guest's and host's
desired UMWAIT_CONTROL. Propagating the guest's value to hardware isn't
required for correct functionality, e.g. KVM intercepts reads and writes
to the MSR, and the latency effects of the settings controlled by the
MSR are not architecturally visible.
As a general rule, KVM should not allow the guest to control power
management settings unless explicitly enabled by userspace, e.g. see
KVM_CAP_X86_DISABLE_EXITS. E.g. Intel's SDM explicitly states that C0.2
can improve the performance of SMT siblings. A devious guest could
disable C0.2 so as to improve the performance of their workloads at the
detriment to workloads running in the host or on other VMs.
Wholesale removal of UMWAIT_CONTROL context switching also fixes a race
condition where updates from the host may cause KVM to enter the guest
with the incorrect value. Because updates are are propagated to all
CPUs via IPI (SMP function callback), the value in hardware may be
stale with respect to the cached value and KVM could enter the guest
with the wrong value in hardware. As above, the guest can't observe the
bad value, but it's a weird and confusing wart in the implementation.
Removal also fixes the unnecessary usage of VMX's atomic load/store MSR
lists. Using the lists is only necessary for MSRs that are required for
correct functionality immediately upon VM-Enter/VM-Exit, e.g. EFER on
old hardware, or for MSRs that need to-the-uop precision, e.g. perf
related MSRs. For UMWAIT_CONTROL, the effects are only visible in the
kernel via TPAUSE/delay(), and KVM doesn't do any form of delay in
vcpu_vmx_run(). Using the atomic lists is undesirable as they are more
expensive than direct RDMSR/WRMSR.
Furthermore, even if giving the guest control of the MSR is legitimate,
e.g. in pass-through scenarios, it's not clear that the benefits would
outweigh the overhead. E.g. saving and restoring an MSR across a VMX
roundtrip costs ~250 cycles, and if the guest diverged from the host
that cost would be paid on every run of the guest. In other words, if
there is a legitimate use case then it should be enabled by a new
per-VM capability.
Note, KVM still needs to emulate MSR_IA32_UMWAIT_CONTROL so that it can
correctly expose other WAITPKG features to the guest, e.g. TPAUSE,
UMWAIT and UMONITOR.
Fixes: 6e3ba4abcea56 ("KVM: vmx: Emulate MSR IA32_UMWAIT_CONTROL")
Cc: stable@vger.kernel.org
Cc: Jingqi Liu <jingqi.liu@intel.com>
Cc: Tao Xu <tao3.xu@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200623005135.10414-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Syzbot reports an use-after-free in workqueue context:
BUG: KASAN: use-after-free in mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
__smsc95xx_mdio_read drivers/net/usb/smsc95xx.c:217 [inline]
smsc95xx_mdio_read+0x583/0x870 drivers/net/usb/smsc95xx.c:278
check_carrier+0xd1/0x2e0 drivers/net/usb/smsc95xx.c:644
process_one_work+0x777/0xf90 kernel/workqueue.c:2274
worker_thread+0xa8f/0x1430 kernel/workqueue.c:2420
kthread+0x2df/0x300 kernel/kthread.c:255
It looks like that smsc95xx_unbind() is freeing the structures that are
still in use by the concurrently running workqueue callback. Thus switch
to using cancel_delayed_work_sync() to ensure the work callback really
is no longer active.
Reported-by: syzbot+29dc7d4ae19b703ff947@syzkaller.appspotmail.com
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The second commit cited below performed a cast of 'u32 buffsize' to
'(u16 *)' when calling mlxsw_sp_port_headroom_8x_adjust():
mlxsw_sp_port_headroom_8x_adjust(mlxsw_sp_port, (u16 *) &buffsize);
Colin noted that this will behave differently on big endian
architectures compared to little endian architectures.
Fix this by following Colin's suggestion and have the function accept
and return 'u32' instead of passing the current size by reference.
Fixes: da382875c616 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Fixes: 60833d54d56c ("mlxsw: spectrum: Adjust headroom buffers for 8x ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Suggested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 7ae7ad2f11ef47 ("net: phy: smsc: use phy_read_poll_timeout()
to simplify the code") will print a lot of logs as follows when Ethernet
cable is not connected:
[ 4.473105] SMSC LAN8710/LAN8720 2188000.ethernet-1:00: lan87xx_read_status failed: -110
When wait 640 ms for check ENERGYON bit, the timeout should not be
regarded as an actual error and an error message also should not be
printed. due to a hardware bug in LAN87XX device, it leads to unstable
detection of plugging in Ethernet cable when LAN87xx is in Energy Detect
Power-Down mode. the workaround for it involves, when the link is down,
and at each read_status() call:
- disable EDPD mode, forcing the PHY out of low-power mode
- waiting 640ms to see if we have any energy detected from the media
- re-enable entry to EDPD mode
This is presumably enough to allow the PHY to notice that a cable is
connected, and resume normal operations to negotiate with the partner.
The problem is that when no media is detected, the 640ms wait times
out and this commit was modified to prints an error message. it is an
inappropriate conversion by used phy_read_poll_timeout() to introduce
this bug. so fix this issue by use read_poll_timeout() to replace
phy_read_poll_timeout().
Fixes: 7ae7ad2f11ef47 ("net: phy: smsc: use phy_read_poll_timeout() to simplify the code")
Reported-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Explicitly pass the L2 GPA to kvm_arch_write_log_dirty(), which for all
intents and purposes is vmx_write_pml_buffer(), instead of having the
latter pull the GPA from vmcs.GUEST_PHYSICAL_ADDRESS. If the dirty bit
update is the result of KVM emulation (rare for L2), then the GPA in the
VMCS may be stale and/or hold a completely unrelated GPA.
Fixes: c5f983f6e8455 ("nVMX: Implement emulated Page Modification Logging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200622215832.22090-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Systems that doesn't yet have the very latest linux/bpf.h header, enum
bpf_stats_type will be undefined, causing compilation warnings. Prevents this
by forward-declaring enum.
Fixes: 0bee106716cf ("libbpf: Add support for command BPF_ENABLE_STATS")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200621031159.2279101-1-andriin@fb.com
|
|
The old address has been bouncing for a while now
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when RMPP MADs are processed while the MAD agent is destroyed,
it could result in use after free of rmpp_recv, as decribed below:
cpu-0 cpu-1
----- -----
ib_mad_recv_done()
ib_mad_complete_recv()
ib_process_rmpp_recv_wc()
unregister_mad_agent()
ib_cancel_rmpp_recvs()
cancel_delayed_work()
process_rmpp_data()
start_rmpp()
queue_delayed_work(rmpp_recv->cleanup_work)
destroy_rmpp_recv()
free_rmpp_recv()
cleanup_work()[1]
spin_lock_irqsave(&rmpp_recv->agent->lock) <-- use after free
[1] cleanup_work() == recv_cleanup_handler
Fix it by waiting for the MAD agent reference count becoming zero before
calling to ib_cancel_rmpp_recvs().
Fixes: 9a41e38a467c ("IB/mad: Use IDR for agent IDs")
Link: https://lore.kernel.org/r/20200621104738.54850-2-leon@kernel.org
Signed-off-by: Shay Drory <shayd@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Don't deref udata if it is NULL
BUG: kernel NULL pointer dereference, address: 0000000000000030
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 SMP PTI
CPU: 2 PID: 1592 Comm: python3 Not tainted 5.7.0-rc6+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
RIP: 0010:create_qp+0x39e/0xae0 [mlx5_ib]
Code: c0 0d 00 00 bf 10 01 00 00 e8 be a9 e4 e0 48 85 c0 49 89 c2 0f 84 0c 07 00 00 41 8b 85 74 63 01 00 0f c8 a9 00 00 00 10 74 0a <41> 8b 46 30 0f c8 41 89 42 14 41 8b 52 18 41 0f b6 4a 1c 0f ca 89
RSP: 0018:ffffc9000067f8b0 EFLAGS: 00010206
RAX: 0000000010170000 RBX: ffff888441313000 RCX: 0000000000000000
RDX: 0000000000000200 RSI: 0000000000000000 RDI: ffff88845b1d4400
RBP: ffffc9000067fa60 R08: 0000000000000200 R09: ffff88845b1d4200
R10: ffff88845b1d4200 R11: ffff888441313000 R12: ffffc9000067f950
R13: ffff88846ac00140 R14: 0000000000000000 R15: ffff88846c2bc000
FS: 00007faa1a3c0540(0000) GS:ffff88846fd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000030 CR3: 0000000446dca003 CR4: 0000000000760ea0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
mlx5_ib_create_qp+0x897/0xfa0 [mlx5_ib]
ib_create_qp+0x9e/0x300 [ib_core]
create_qp+0x92d/0xb20 [ib_uverbs]
? ib_uverbs_cq_event_handler+0x30/0x30 [ib_uverbs]
? release_resource+0x30/0x30
ib_uverbs_create_qp+0xc4/0xe0 [ib_uverbs]
ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0xc8/0xf0 [ib_uverbs]
ib_uverbs_run_method+0x223/0x770 [ib_uverbs]
? track_pfn_remap+0xa7/0x100
? uverbs_disassociate_api+0xd0/0xd0 [ib_uverbs]
? remap_pfn_range+0x358/0x490
ib_uverbs_cmd_verbs.isra.6+0x19b/0x370 [ib_uverbs]
? rdma_umap_priv_init+0x82/0xe0 [ib_core]
? vm_mmap_pgoff+0xec/0x120
ib_uverbs_ioctl+0xc0/0x120 [ib_uverbs]
ksys_ioctl+0x92/0xb0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x48/0x130
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: e383085c2425 ("RDMA/mlx5: Set ECE options during QP create")
Link: https://lore.kernel.org/r/20200621115959.60126-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
translate_gpa() returns a GPA, assigning it to 'real_gfn' seems obviously
wrong. There is no real issue because both 'gpa_t' and 'gfn_t' are u64 and
we don't use the value in 'real_gfn' as a GFN, we do
real_gfn = gpa_to_gfn(real_gfn);
instead. 'If you see a "buffalo" sign on an elephant's cage, do not trust
your eyes', but let's fix it for good.
No functional change intended.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200622151435.752560-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The following race can cause lost map update events:
cpu1 cpu2
apic_map_dirty = true
------------------------------------------------------------
kvm_recalculate_apic_map:
pass check
mutex_lock(&kvm->arch.apic_map_lock);
if (!kvm->arch.apic_map_dirty)
and in process of updating map
-------------------------------------------------------------
other calls to
apic_map_dirty = true might be too late for affected cpu
-------------------------------------------------------------
apic_map_dirty = false
-------------------------------------------------------------
kvm_recalculate_apic_map:
bail out on
if (!kvm->arch.apic_map_dirty)
To fix it, record the beginning of an update of the APIC map in
apic_map_dirty. If another APIC map change switches apic_map_dirty
back to DIRTY during the update, kvm_recalculate_apic_map should not
make it CLEAN, and the other caller will go through the slow path.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Query a dynamically-allocated counter before release it, to update it's
hwcounters and log all of them into history data. Otherwise all values of
these hwcounters will be lost.
Fixes: f34a55e497e8 ("RDMA/core: Get sum value of all counters when perform a sysfs stat read")
Link: https://lore.kernel.org/r/20200621110000.56059-1-leon@kernel.org
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Quite a lot of fixes here for no single reason.
There's a collection of the usual sort of device specific fixes and
also a bunch of people have been working on spidev and the userspace
test program spidev_test so they've got an unusually large collection
of small fixes"
* tag 'spi-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spidev: fix a potential use-after-free in spidev_release()
spi: spidev: fix a race between spidev_release and spidev_remove
spi: stm32-qspi: Fix error path in case of -EPROBE_DEFER
spi: uapi: spidev: Use TABs for alignment
spi: spi-fsl-dspi: Free DMA memory with matching function
spi: tools: Add macro definitions to fix build errors
spi: tools: Make default_tx/rx and input_tx static
spi: dt-bindings: amlogic, meson-gx-spicc: Fix schema for meson-g12a
spi: rspi: Use requested instead of maximum bit rate
spi: spidev_test: Use %u to format unsigned numbers
spi: sprd: switch the sequence of setting WDG_LOAD_LOW and _HIGH
|
|
Guest fails to online hotplugged CPU with error
smpboot: do_boot_cpu failed(-1) to wakeup CPU#4
It's caused by the fact that kvm_apic_set_state(), which used to call
recalculate_apic_map() unconditionally and pulled hotplugged CPU into
apic map, is updating map conditionally on state changes. In this case
the APIC map is not considered dirty and the is not updated.
Fix the issue by forcing unconditional update from kvm_apic_set_state(),
like it used to be.
Fixes: 4abaffce4d25a ("KVM: LAPIC: Recalculate apic map in batch")
Cc: stable@vger.kernel.org
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200622160830.426022-1-imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"This has a fix for the refactoring out of the pickable ranges
functionality, plus the removal of a BROKEN dependency on mt6358 now
that the dependencies were merged in -rc1 and a couple of device
specific fixes"
* tag 'regulator-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: mt6358: Remove BROKEN dependency
regualtor: pfuze100: correct sw1a/sw2 on pfuze3000
regulator: Fix pickable ranges mapping
regulator: da9063: fix LDO9 suspend and warning.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A few small fixes, none of which are likely to have any substantial
impact here - the most substantial one is a fix for a long standing
memory leak on devices that use register patching which will only have
an impact if the device is removed and re-added"
* tag 'regmap-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix memory leak from regmap_register_patch
regmap: fix the kerneldoc for regmap_test_bits()
regmap: fix alignment issue
|
|
It should not make any significant difference but reduce stub code.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Link: https://lore.kernel.org/r/20200418102217.32327-9-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This way behavior for vhost is more like a VM.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Link: https://lore.kernel.org/r/20200418102217.32327-8-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
So we can reset after that in the main loop.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Link: https://lore.kernel.org/r/20200418102217.32327-7-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
As updated in ("2a2d1382fe9d virtio: Add improved queue allocation API")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Link: https://lore.kernel.org/r/20200418102217.32327-6-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Currently, it only removes and add backend, but it will reset vq
position in future commits.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Link: https://lore.kernel.org/r/20200418102217.32327-5-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
So we can test with non-deterministic batches in flight.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Link: https://lore.kernel.org/r/20200418102217.32327-4-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This allow to test vhost having >1 buffers in flight
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Link: https://lore.kernel.org/r/20200401183118.8334-5-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20200418102217.32327-3-eperezma@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Virtio-mem managed memory is always detected and added by the virtio-mem
driver, never using something like the firmware-provided memory map.
This is the case after an ordinary system reboot, and has to be guaranteed
after kexec. Especially, virtio-mem added memory resources can contain
inaccessible parts ("unblocked memory blocks"), blindly forwarding them
to a kexec kernel is dangerous, as unplugged memory will get accessed
(esp. written).
Let's use the new way of adding special driver-managed memory introduced
in commit 7b7b27214bba ("mm/memory_hotplug: introduce
add_memory_driver_managed()").
This will result in no entries in /sys/firmware/memmap ("raw firmware-
provided memory map"), the memory resource will be flagged
IORESOURCE_MEM_DRIVER_MANAGED (esp., kexec_file_load() will not place
kexec images on this memory), and it is exposed as "System RAM
(virtio_mem)" in /proc/iomem, so esp. kexec-tools can properly handle it.
Example /proc/iomem before this change:
[...]
140000000-333ffffff : virtio0
140000000-147ffffff : System RAM
334000000-533ffffff : virtio1
338000000-33fffffff : System RAM
340000000-347ffffff : System RAM
348000000-34fffffff : System RAM
[...]
Example /proc/iomem after this change:
[...]
140000000-333ffffff : virtio0
140000000-147ffffff : System RAM (virtio_mem)
334000000-533ffffff : virtio1
338000000-33fffffff : System RAM (virtio_mem)
340000000-347ffffff : System RAM (virtio_mem)
348000000-34fffffff : System RAM (virtio_mem)
[...]
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Fixes: 5f1f79bbc9e26 ("virtio-mem: Paravirtualized memory hotplug")
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200611093518.5737-1-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
|
|
Smatch complains that "rc" can be uninitialized if we hit the "break;"
statement on the first iteration through the loop. I suspect that this
can't happen in real life, but returning a zero literal is cleaner and
silence the static checker warning.
Fixes: 5f1f79bbc9e2 ("virtio-mem: Paravirtualized memory hotplug")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200610085911.GC5439@mwanda
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The "vma->vm_pgoff" variable is an unsigned long so if it's larger than
INT_MAX then "index" can be negative leading to an underflow. Fix this
by changing the type of "index" to "unsigned long".
Fixes: ddd89d0a059d ("vhost_vdpa: support doorbell mapping via mmap")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200610085852.GB5439@mwanda
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Fix two typos in the comments for __vdpa_alloc_device().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200527060528.9100-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.8
This is a collection of mostly small fixes, mostly fixing fallout from
some of the DPCM changes that went in last time around which shook out
some issues on i.MX and Qualcomm platforms. The addition of a managed
version of snd_soc_register_dai() is to fix resource leaks.
There's also a few new device IDs for x86 systems.
|
|
This reverts commit 8ece3b3eb576a78d2e67ad4c3a80a39fa6708809.
This commit broke userspace. Bash uses ESPIPE to determine whether or
not the file should be read using "unbuffered I/O", which means reading
1 byte at a time instead of 128 bytes at a time. I used to use bash to
read through kmsg in a really quite nasty way:
while read -t 0.1 -r line 2>/dev/null || [[ $? -ne 142 ]]; do
echo "SARU $line"
done < /dev/kmsg
This will show all lines that can fit into the 128 byte buffer, and skip
lines that don't. That's pretty awful, but at least it worked.
With this change, bash now tries to do 1-byte reads, which means it
skips all the lines, which is worse than before.
Now, I don't really care very much about this, and I'm already look for
a workaround. But I did just spend an hour trying to figure out why my
scripts were broken. Either way, it makes no difference to me personally
whether this is reverted, but it might be something to consider. If you
declare that "trying to read /dev/kmsg with bash is terminally stupid
anyway," I might be inclined to agree with you. But do note that bash
uses lseek(fd, 0, SEEK_CUR)==>ESPIPE to determine whether or not it's
reading from a pipe.
Cc: Bruno Meneguele <bmeneg@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull SELinux fixes from Paul Moore:
"Three small patches to fix problems in the SELinux code, all found via
clang.
Two patches fix potential double-free conditions and one fixes an
undefined return value"
* tag 'selinux-pr-20200621' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix undefined return of cond_evaluate_expr
selinux: fix a double free in cond_read_node()/cond_read_list()
selinux: fix double free
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some early fixes collected during the first week after the merge
window, all pretty self-evident, with the details below. The revert is
the crucial thing.
- Fix a warning on the Qualcomm SPMI GPIO chip being instatiated
twice without a unique irqchip struct
- Use the noirq variants of the suspend and resume callbacks in the
Tegra driver
- Clean up the errorpath on the MCP23s08 driver
- Revert the use of devm_of_iomap() in the Freescale driver as it was
regressing the platform
- Add some missing pins in the Qualcomm IPQ6018 driver
- Fix a simple documentation bug in the pinctrl-single driver"
* tag 'pinctrl-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: single: fix function name in documentation
pinctrl: qcom: ipq6018 Add missing pins in qpic pin group
Revert "pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'"
pinctrl: mcp23s08: Split to three parts: fix ptr_ret.cocci warnings
pinctrl: tegra: Use noirq suspend/resume callbacks
pinctrl: qcom: spmi-gpio: fix warning about irq chip reusage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix -gz=zlib compiler option test for CONFIG_DEBUG_INFO_COMPRESSED
- improve cc-option in scripts/Kbuild.include to clean up temp files
- improve cc-option in scripts/Kconfig.include for more reliable
compile option test
- do not copy modules.builtin by 'make install' because it would break
existing systems
- use 'userprogs' syntax for watch_queue sample
* tag 'kbuild-fixes-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
samples: watch_queue: build sample program for target architecture
Revert "Makefile: install modules.builtin even if CONFIG_MODULES=n"
scripts: Fix typo in headers_install.sh
kconfig: unify cc-option and as-option
kbuild: improve cc-option to clean up all temporary files
Makefile: Improve compressed debug info support detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- One fix for the interrupt rework we did last release which broke
KVM-PR
- Three commits fixing some fallout from the READ_ONCE() changes
interacting badly with our 8xx 16K pages support, which uses a pte_t
that is a structure of 4 actual PTEs
- A cleanup of the 8xx pte_update() to use the newly added pmd_off()
- A fix for a crash when handling an oops if CONFIG_DEBUG_VIRTUAL is
enabled
- A minor fix for the SPU syscall generation
Thanks to Aneesh Kumar K.V, Christian Zigotzky, Christophe Leroy, Mike
Rapoport, Nicholas Piggin.
* tag 'powerpc-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/8xx: Provide ptep_get() with 16k pages
mm: Allow arches to provide ptep_get()
mm/gup: Use huge_ptep_get() in gup_hugepte()
powerpc/syscalls: Use the number when building SPU syscall table
powerpc/8xx: use pmd_off() to access a PMD entry in pte_update()
powerpc/64s: Fix KVM interrupt using wrong save area
powerpc: Fix kernel crash in show_instructions() w/DEBUG_VIRTUAL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- NULL dereference in octeontx
- PM reference imbalance in ks-sa
- deadlock in crypto manager
- memory leak in drbg
- missing socket limit check on receive SG list size in algif_skcipher
- typos in caam
- warnings in ccp and hisilicon
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: drbg - always try to free Jitter RNG instance
crypto: marvell/octeontx - Fix a potential NULL dereference
crypto: algboss - don't wait during notifier callback
crypto: caam - fix typos
crypto: ccp - Fix sparse warnings in sev-dev
crypto: hisilicon - Cap block size at 2^31
crypto: algif_skcipher - Cap recv SG list at ctx->used
hwrng: ks-sa - Fix runtime PM imbalance on error
|
|
This userspace program includes UAPI headers exported to usr/include/.
'make headers' always works for the target architecture (i.e. the same
architecture as the kernel), so the sample program should be built for
the target as well. Kbuild now supports 'userprogs' for that.
I also guarded the CONFIG option by 'depends on CC_CAN_LINK' because
$(CC) may not provide libc.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
This reverts commit e0b250b57dcf403529081e5898a9de717f96b76b,
which broke build systems that need to install files to a certain
path, but do not set INSTALL_MOD_PATH when invoking 'make install'.
$ make INSTALL_PATH=/tmp/destdir install
mkdir: cannot create directory ‘/lib/modules/5.8.0-rc1+/’: Permission denied
Makefile:1342: recipe for target '_builtin_inst_' failed
make: *** [_builtin_inst_] Error 1
While modules.builtin is useful also for CONFIG_MODULES=n, this change
in the behavior is quite unexpected. Maybe "make modules_install"
can install modules.builtin irrespective of CONFIG_MODULES as Jonas
originally suggested.
Anyway, that commit should be reverted ASAP.
Reported-by: Douglas Anderson <dianders@chromium.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
The user tool modinfo is used to get information on kernel modules, including a
description where it is available.
This patch adds a brief MODULE_DESCRIPTION to the following modules:
9p
drop_monitor
esp4_offload
esp6_offload
fou
fou6
ila
sch_fq
sch_fq_codel
sch_hhf
Signed-off-by: Rob Gill <rrobgill@protonmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When preallocated service calls are being discarded, they're passed to
->discard_new_call() to have the caller clean up any attached higher-layer
preallocated pieces before being marked completed. However, the act of
marking them completed now invokes the call's notification function - which
causes a problem because that function might assume that the previously
freed pieces of memory are still there.
Fix this by setting a dummy notification function on the socket after
calling ->discard_new_call().
This results in the following kasan message when the kafs module is
removed.
==================================================================
BUG: KASAN: use-after-free in afs_wake_up_async_call+0x6aa/0x770 fs/afs/rxrpc.c:707
Write of size 1 at addr ffff8880946c39e4 by task kworker/u4:1/21
CPU: 0 PID: 21 Comm: kworker/u4:1 Not tainted 5.8.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x18f/0x20d lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd3/0x413 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
afs_wake_up_async_call+0x6aa/0x770 fs/afs/rxrpc.c:707
rxrpc_notify_socket+0x1db/0x5d0 net/rxrpc/recvmsg.c:40
__rxrpc_set_call_completion.part.0+0x172/0x410 net/rxrpc/recvmsg.c:76
__rxrpc_call_completed net/rxrpc/recvmsg.c:112 [inline]
rxrpc_call_completed+0xca/0xf0 net/rxrpc/recvmsg.c:111
rxrpc_discard_prealloc+0x781/0xab0 net/rxrpc/call_accept.c:233
rxrpc_listen+0x147/0x360 net/rxrpc/af_rxrpc.c:245
afs_close_socket+0x95/0x320 fs/afs/rxrpc.c:110
afs_net_exit+0x1bc/0x310 fs/afs/main.c:155
ops_exit_list.isra.0+0xa8/0x150 net/core/net_namespace.c:186
cleanup_net+0x511/0xa50 net/core/net_namespace.c:603
process_one_work+0x965/0x1690 kernel/workqueue.c:2269
worker_thread+0x96/0xe10 kernel/workqueue.c:2415
kthread+0x3b5/0x4a0 kernel/kthread.c:291
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293
Allocated by task 6820:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:494 [inline]
__kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:467
kmem_cache_alloc_trace+0x153/0x7d0 mm/slab.c:3551
kmalloc include/linux/slab.h:555 [inline]
kzalloc include/linux/slab.h:669 [inline]
afs_alloc_call+0x55/0x630 fs/afs/rxrpc.c:141
afs_charge_preallocation+0xe9/0x2d0 fs/afs/rxrpc.c:757
afs_open_socket+0x292/0x360 fs/afs/rxrpc.c:92
afs_net_init+0xa6c/0xe30 fs/afs/main.c:125
ops_init+0xaf/0x420 net/core/net_namespace.c:151
setup_net+0x2de/0x860 net/core/net_namespace.c:341
copy_net_ns+0x293/0x590 net/core/net_namespace.c:482
create_new_namespaces+0x3fb/0xb30 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xbd/0x1f0 kernel/nsproxy.c:231
ksys_unshare+0x43d/0x8e0 kernel/fork.c:2983
__do_sys_unshare kernel/fork.c:3051 [inline]
__se_sys_unshare kernel/fork.c:3049 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3049
do_syscall_64+0x60/0xe0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 21:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
kasan_set_free_info mm/kasan/common.c:316 [inline]
__kasan_slab_free+0xf7/0x140 mm/kasan/common.c:455
__cache_free mm/slab.c:3426 [inline]
kfree+0x109/0x2b0 mm/slab.c:3757
afs_put_call+0x585/0xa40 fs/afs/rxrpc.c:190
rxrpc_discard_prealloc+0x764/0xab0 net/rxrpc/call_accept.c:230
rxrpc_listen+0x147/0x360 net/rxrpc/af_rxrpc.c:245
afs_close_socket+0x95/0x320 fs/afs/rxrpc.c:110
afs_net_exit+0x1bc/0x310 fs/afs/main.c:155
ops_exit_list.isra.0+0xa8/0x150 net/core/net_namespace.c:186
cleanup_net+0x511/0xa50 net/core/net_namespace.c:603
process_one_work+0x965/0x1690 kernel/workqueue.c:2269
worker_thread+0x96/0xe10 kernel/workqueue.c:2415
kthread+0x3b5/0x4a0 kernel/kthread.c:291
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293
The buggy address belongs to the object at ffff8880946c3800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 484 bytes inside of
1024-byte region [ffff8880946c3800, ffff8880946c3c00)
The buggy address belongs to the page:
page:ffffea000251b0c0 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0xfffe0000000200(slab)
raw: 00fffe0000000200 ffffea0002546508 ffffea00024fa248 ffff8880aa000c40
raw: 0000000000000000 ffff8880946c3000 0000000100000002 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880946c3880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880946c3900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880946c3980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8880946c3a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880946c3a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Reported-by: syzbot+d3eccef36ddbd02713e9@syzkaller.appspotmail.com
Fixes: 5ac0d62226a0 ("rxrpc: Fix missing notification")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2020-06-19
An update from ieee802154 for your *net* tree.
Just two small maintenance fixes to update references to the new project
homepage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
