| Age | Commit message (Collapse) | Author |
|---|
|
On JZ4760 and JZ4760B, SD cards fail to run if the maximum clock
rate is set to 50 MHz, even though the controller officially does
support it.
Until the actual bug is found and fixed, limit the maximum clock rate to
24 MHz.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230131210229.68129-1-paul@crapouillou.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If mmc_add_host() fails, it doesn't need to call mmc_remove_host(),
or it will cause null-ptr-deref, because of deleting a not added
device in mmc_remove_host().
To fix this, goto label 'fail_glue_init', if mmc_add_host() fails,
and change the label 'fail_add_host' to 'fail_gpiod_request'.
Fixes: 15a0580ced08 ("mmc_spi host driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230131013835.3564011-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If sdio_add_func() or sdio_init_func() fails, sdio_remove_func() can
not release the resources, because the sdio function is not presented
in these two cases, it won't call of_node_put() or put_device().
To fix these leaks, make sdio_func_present() only control whether
device_del() needs to be called or not, then always call of_node_put()
and put_device().
In error case in sdio_init_func(), the reference of 'card->dev' is
not get, to avoid redundant put in sdio_free_func_cis(), move the
get_device() to sdio_alloc_func() and put_device() to sdio_release_func(),
it can keep the get/put function be balanced.
Without this patch, while doing fault inject test, it can get the
following leak reports, after this fix, the leak is gone.
unreferenced object 0xffff888112514000 (size 2048):
comm "kworker/3:2", pid 65, jiffies 4294741614 (age 124.774s)
hex dump (first 32 bytes):
00 e0 6f 12 81 88 ff ff 60 58 8d 06 81 88 ff ff ..o.....`X......
10 40 51 12 81 88 ff ff 10 40 51 12 81 88 ff ff .@Q......@Q.....
backtrace:
[<000000009e5931da>] kmalloc_trace+0x21/0x110
[<000000002f839ccb>] mmc_alloc_card+0x38/0xb0 [mmc_core]
[<0000000004adcbf6>] mmc_sdio_init_card+0xde/0x170 [mmc_core]
[<000000007538fea0>] mmc_attach_sdio+0xcb/0x1b0 [mmc_core]
[<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core]
unreferenced object 0xffff888112511000 (size 2048):
comm "kworker/3:2", pid 65, jiffies 4294741623 (age 124.766s)
hex dump (first 32 bytes):
00 40 51 12 81 88 ff ff e0 58 8d 06 81 88 ff ff .@Q......X......
10 10 51 12 81 88 ff ff 10 10 51 12 81 88 ff ff ..Q.......Q.....
backtrace:
[<000000009e5931da>] kmalloc_trace+0x21/0x110
[<00000000fcbe706c>] sdio_alloc_func+0x35/0x100 [mmc_core]
[<00000000c68f4b50>] mmc_attach_sdio.cold.18+0xb1/0x395 [mmc_core]
[<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core]
Fixes: 3d10a1ba0d37 ("sdio: fix reference counting in sdio_remove_func()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230130125808.3471254-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This makes the text read a little better.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230129130059.1322858-1-j.neuschaefer@gmx.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some SDIO WiFi modules stopped working after SDIO interrupt mode
was added if cap_sdio_irq isn't set in device tree. This patch was
confirmed to fix the issue.
Fixes: 066ecde6d826 ("mmc: meson-gx: add SDIO interrupt support")
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Tested-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/816cba9f-ff92-31a2-60f0-aca542d1d13e@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use new function devm_mmc_alloc_host() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/728f159b-885f-c78a-1a3d-f55c245250e1@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add a device-managed version of mmc_alloc_host().
The argument order is reversed compared to mmc_alloc_host() because
device-managed functions typically have the device argument first.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/6d8f9fdc-7c9e-8e4f-e6ef-5470b971c74e@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On r8a7791/koelsch:
kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xc3a34e00 (size 64):
comm "swapper/0", pid 1, jiffies 4294937460 (age 199.080s)
hex dump (first 32 bytes):
b4 5d 81 f0 b4 5d 81 f0 c0 b0 a2 c3 00 00 00 00 .]...]..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fe3aa979>] __kmalloc+0xf0/0x140
[<34bd6bc0>] resource_list_create_entry+0x18/0x38
[<767046bc>] pci_add_resource_offset+0x20/0x68
[<b3f3edf2>] devm_of_pci_get_host_bridge_resources.constprop.0+0xb0/0x390
When coalescing two resources for a contiguous aperture, the second
resource is enlarged to cover the full contiguous range, while the first
resource is marked invalid. This invalidation is done by clearing the
flags, start, and end members.
When adding the initial resources to the bus later, invalid resources are
skipped. Unfortunately, the check for an invalid resource considers only
the end member, causing false positives.
E.g. on r8a7791/koelsch, root bus resource 0 ("bus 00") is skipped, and no
longer registered with pci_bus_insert_busn_res() (causing the memory leak),
nor printed:
pci-rcar-gen2 ee090000.pci: host bridge /soc/pci@ee090000 ranges:
pci-rcar-gen2 ee090000.pci: MEM 0x00ee080000..0x00ee08ffff -> 0x00ee080000
pci-rcar-gen2 ee090000.pci: PCI: revision 11
pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00
-pci_bus 0000:00: root bus resource [bus 00]
pci_bus 0000:00: root bus resource [mem 0xee080000-0xee08ffff]
Fix this by only skipping resources where all of the flags, start, and end
members are zero.
Fixes: 7c3855c423b17f6c ("PCI: Coalesce host bridge contiguous apertures")
Link: https://lore.kernel.org/r/da0fcd5e86c74239be79c7cb03651c0fce31b515.1676036673.git.geert+renesas@glider.be
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
|
|
* kvm-arm64/parallel-access-faults:
: Parallel stage-2 access fault handling
:
: The parallel faults changes that went in to 6.2 covered most stage-2
: aborts, with the exception of stage-2 access faults. Building on top of
: the new infrastructure, this series adds support for handling access
: faults (i.e. updating the access flag) in parallel.
:
: This is expected to provide a performance uplift for cores that do not
: implement FEAT_HAFDBS, such as those from the fruit company.
KVM: arm64: Condition HW AF updates on config option
KVM: arm64: Handle access faults behind the read lock
KVM: arm64: Don't serialize if the access flag isn't set
KVM: arm64: Return EAGAIN for invalid PTE in attr walker
KVM: arm64: Ignore EAGAIN for walks outside of a fault
KVM: arm64: Use KVM's pte type/helpers in handle_access_fault()
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
* kvm-arm64/virtual-cache-geometry:
: Virtualized cache geometry for KVM guests, courtesy of Akihiko Odaki.
:
: KVM/arm64 has always exposed the host cache geometry directly to the
: guest, even though non-secure software should never perform CMOs by
: Set/Way. This was slightly wrong, as the cache geometry was derived from
: the PE on which the vCPU thread was running and not a sanitized value.
:
: All together this leads to issues migrating VMs on heterogeneous
: systems, as the cache geometry saved/restored could be inconsistent.
:
: KVM/arm64 now presents 1 level of cache with 1 set and 1 way. The cache
: geometry is entirely controlled by userspace, such that migrations from
: older kernels continue to work.
KVM: arm64: Mark some VM-scoped allocations as __GFP_ACCOUNT
KVM: arm64: Normalize cache configuration
KVM: arm64: Mask FEAT_CCIDX
KVM: arm64: Always set HCR_TID2
arm64/cache: Move CLIDR macro definitions
arm64/sysreg: Add CCSIDR2_EL1
arm64/sysreg: Convert CCSIDR_EL1 to automatic generation
arm64: Allow the definition of UNKNOWN system register fields
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
Merge the SME2 branch to fix up a rather annoying conflict due to the
EL2 finalization refactor.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
Merge the kvm_init() + hardware enable rework to avoid conflicts
with kvmarm.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
As a part of the transition towards callback mechanism for signalling the
events from EPC to EPF, let's use the link_up() callback in the place of
the LINK_UP notifier. This also removes the notifier support completely
from the PCI endpoint framework.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@kernel.org>
|
|
Instead of using the notifiers for passing the events from EPC to EPF,
let's introduce a callback based mechanism where the EPF drivers can
populate relevant callbacks for EPC events they want to subscribe.
The use of notifiers in kernel is not recommended if there is a real link
between the sender and receiver, like in this case. Also, the existing
atomic notifier forces the notification functions to be in atomic context
while the caller may be in non-atomic context. For instance, the two
in-kernel users of the notifiers, pcie-qcom and pcie-tegra194, both are
calling the notifier functions in non-atomic context (from threaded IRQ
handlers). This creates a sleeping in atomic context issue with the
existing EPF_TEST driver that calls the EPC APIs that may sleep.
For all these reasons, let's get rid of the notifier chains and use the
simple callback mechanism for signalling the events from EPC to EPF
drivers. This preserves the context of the caller and avoids the latency
of going through a separate interface for triggering the notifications.
As a first step of the transition, the core_init() callback is introduced
in this commit, that'll replace the existing CORE_INIT notifier used for
signalling the init complete event from EPC.
During the occurrence of the event, EPC will go over the list of EPF
drivers attached to it and will call the core_init() callback if available.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@kernel.org>
|
|
The EPC controller maintains a list of EPF drivers added to it. For
protecting this list against the concurrent accesses, the epc->lock
(used for protecting epc_ops) has been used so far. Since there were
no users trying to use epc_ops and modify the pci_epf list simultaneously,
this was not an issue.
But with the addition of callback mechanism for passing the events, this
will be a problem. Because the pci_epf list needs to be iterated first
for getting hold of the EPF driver and then the relevant event specific
callback needs to be called for the driver.
If the same epc->lock is used, then it will result in a deadlock scenario.
For instance,
...
mutex_lock(&epc->lock);
list_for_each_entry(epf, &epc->pci_epf, list) {
epf->event_ops->core_init(epf);
|
|-> pci_epc_set_bar();
|
|-> mutex_lock(&epc->lock) # DEADLOCK
...
So to fix this issue, use a separate lock called "list_lock" for
protecting the pci_epf list against the concurrent accesses. This lock
will also be used by the callback mechanism.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
dw_pcie_ep_linkup() may take more time to execute depending on the EPF
driver implementation. Calling this API in the hard IRQ handler is not
encouraged since the hard IRQ handlers are supposed to complete quickly.
So move the dw_pcie_ep_linkup() call to threaded IRQ handler.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
|
|
The "dra7xx-pcie-main" hard IRQ handler is just printing the IRQ status
and calling the dw_pcie_ep_linkup() API if LINK_UP status is set. But the
execution of dw_pcie_ep_linkup() depends on the EPF driver and may take
more time depending on the EPF implementation.
In general, hard IRQ handlers are supposed to return quickly and not block
for so long. Moreover, there is no real need of the current IRQ handler to
be a hard IRQ handler. So switch to the threaded IRQ handler for the
"dra7xx-pcie-main" IRQ.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
qcom,rpmcc bindings expect RPM clock controller to be named generic
"clock-controller":
rpm-glink: rpm-requests: 'qcom,rpmcc' does not match any of the regexes: '^regulators(-[01])?$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230208101545.45711-3-krzysztof.kozlowski@linaro.org
|
|
Bindings expect (and most of DTS use) the RPM G-Link node name to be
"rpm-requests".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230208101545.45711-2-krzysztof.kozlowski@linaro.org
|
|
Bindings expect (and most of DTS use) the RPM G-Link node name to be
"rpm-requests".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230208101545.45711-1-krzysztof.kozlowski@linaro.org
|
|
Enable the pinctrl, GCC clock and interconnect drivers in order to allow
booting SA8775P boards. The drivers need to be built-in for QUPv3 and
subsequently UART console to work.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Eric Chanudet <echanude@redhat.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230209103531.469809-1-brgl@bgdev.pl
|
|
The interconnect property is already present in the qce node, which
is the consumer of the cryptobam, so no need for an interconnect property
as documented by the bindings.
Fixes: 433477c3bf0b ("arm64: dts: qcom: sm8550: add QCrypto nodes")
Suggested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230209-topic-sm8550-upstream-cryptobam-remove-interconnect-v1-1-84587c7bad0f@linaro.org
|
|
Tune the PWM to solve screen flashing issue and high frequency noise.
While at it, the comment for the PWM settings incorrectly said we were
using a 5kHz duty cycle. It should have said "period", not "duty cycle".
Correct this while updating the values.
Signed-off-by: Owen Yang <ecs.taipeikernel@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213105803.v2.1.I610cef0ead2d5df1f7bd18bc0e0ae040b03725d0@changeid
|
|
Nodes like pwrkey, resin, iadc, adc-tm, temp-alarm which are the grand
children of spmi_bus node represent the interrupt generating devices but
don't have "interrupt-parent" property.
As per the devicetree spec v0.3, section 2.4:
"The physical wiring of an interrupt source to an interrupt controller is
represented in the devicetree with the interrupt-parent property. Nodes
that represent interrupt-generating devices contain an interrupt-parent
property which has a phandle value that points to the device to which the
device’s interrupts are routed, typically an interrupt controller. If an
interrupt-generating device does not have an interrupt-parent property,
its interrupt parent is assumed to be its devicetree parent."
This clearly says that if the "interrupt-parent" property is absent, then
the immediate devicetree parent will be assumed as the interrupt parent.
But the immediate parents of these nodes are not interrupt controllers
themselves.
This may lead to failure while wiring the interrupt for these nodes by an
operating system. But a few operating systems like Linux, workaround this
issue by walking up the parent nodes until it finds the "interrupt-cells"
property. Then the node that has the "interrupt-cells" property will be
used as the interrupt parent.
But this workaround is not as per the DT spec and is not being implemented
by other operating systems such as OpenBSD.
Hence, fix this issue by adding the "interrupts-extended" property that
explicitly specifies the spmi_bus node as the interrupt parent. Note that
the "interrupts-extended" property is chosen over "interrupt-parent" as it
allows specifying both interrupt parent phandle and interrupt specifiers in
a single property.
Reported-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213090118.11527-1-manivannan.sadhasivam@linaro.org
|
|
Enable all i2c busses where something is connected on this phone. Add
comments as placeholders for which components are still missing.
Also enable gpi_dma and the other qupv3 for that.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213-fp4-more-i2c-v2-2-1c459c572f80@fairphone.com
|
|
Currently the dts contains a mix of status-as-first-property (old qcom
style) and status-as-last-property (new style).
Move all status properties down to the bottom once and for all so that
the style is consistent between different nodes.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213-fp4-more-i2c-v2-1-1c459c572f80@fairphone.com
|
|
A special compatible was introduced for PMK8350 both in the driver and
the bindings to facilitate for 2 base registers (PBS & HLOS). Use it.
Fixes: b2de43136058 ("arm64: dts: qcom: pmk8350: Add peripherals for pmk8350")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213212930.2115182-1-konrad.dybcio@linaro.org
|
|
The QCOM_PMIC_GLINK implements the parts of a TCPM necessary for
negotiating DP altmode and the TYPEC_MUX_GPIO_SBU driver is used for
controlling connection and orientation switching of the SBU lanes in the
USB-C connector Enable these to enable USB Type-C DisplayPort on
SC8280XP laptops.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213215619.1362566-5-quic_bjorande@quicinc.com
|
|
Like on the CRD, add the necessary nodes to enable USB Type-C
altmode-based external display on the Lenovo ThinkPad X13s.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213215619.1362566-4-quic_bjorande@quicinc.com
|
|
The SC8280XP CRD control over battery management and its two USB Type-C
port using pmic_glink and two GPIO-based SBU muxes.
Enable the two DisplayPort instances, GPIO SBU mux instance and
pmic_glink with the two connectors on the CRD.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213215619.1362566-3-quic_bjorande@quicinc.com
|
|
Add the two DisplayPort controllers that are attached to QMP phys for
providing display output on USB Type-C.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213215619.1362566-2-quic_bjorande@quicinc.com
|
|
Enable the GPU on the SM8350-HDK device. The ZAP shader is required for
the GPU to function properly.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230209133839.762631-7-dmitry.baryshkov@linaro.org
|
|
Add device nodes required to enable GPU on the SM8350 platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[bjorn: Workaround for lacking RPMH_REGULATOR_LEVEL_LOW_SVS_L1 constant]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230209133839.762631-6-dmitry.baryshkov@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Twelve hotfixes, mostly against mm/.
Five of these fixes are cc:stable"
* tag 'mm-hotfixes-stable-2023-02-13-13-50' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
of: reserved_mem: Have kmemleak ignore dynamically allocated reserved mem
scripts/gdb: fix 'lx-current' for x86
lib: parser: optimize match_NUMBER apis to use local array
mm: shrinkers: fix deadlock in shrinker debugfs
mm: hwpoison: support recovery from ksm_might_need_to_copy()
kasan: fix Oops due to missing calls to kasan_arch_is_ready()
revert "squashfs: harden sanity check in squashfs_read_xattr_id_table"
fsdax: dax_unshare_iter() should return a valid length
mm/gup: add folio to list when folio_isolate_lru() succeed
aio: fix mremap after fork null-deref
mailmap: add entry for Alexander Mikhalitsyn
mm: extend max struct page size for kmsan
|
|
Finish reordering DT nodes by their address. Move PDC, tsens, AOSS,
SRAM, SPMI and TLMM nodes to the proper position.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230209133839.762631-5-dmitry.baryshkov@linaro.org
|
|
Continue ordering DT nodes by their address. Move RNG, UFS, system NoC
and SLPI nodes to the proper position.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230209133839.762631-4-dmitry.baryshkov@linaro.org
|
|
Somehow sm8350 got its device nodes not fully sorted. Start reordering
DT nodes by their address. Move apps SMMU, GIC, timer, apps RSC, cpufreq
ADSP and cDSP nodes to the end to the proper position at the end of
/soc/.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230209133839.762631-3-dmitry.baryshkov@linaro.org
|
|
The PMIC GLINK service, running on a coprocessor of modern Qualcomm
platforms, deals with battery charging and fuel gauging, as well as
reporting status of AC and wireless power supplies.
As this is just one of the functionalities provided by the PMIC GLINK
service, this power supply driver is implemented as an auxilirary bus
driver, spawned by the main "pmic glink" driver when the PMIC GLINK
service is detected.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM8350 PDX215
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-MTP & SM8450-HDK
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230207144241.1767973-1-quic_bjorande@quicinc.com
|
|
This patch introduces non-owning reference semantics to the verifier,
specifically linked_list API kfunc handling. release_on_unlock logic for
refs is refactored - with small functional changes - to implement these
semantics, and bpf_list_push_{front,back} are migrated to use them.
When a list node is pushed to a list, the program still has a pointer to
the node:
n = bpf_obj_new(typeof(*n));
bpf_spin_lock(&l);
bpf_list_push_back(&l, n);
/* n still points to the just-added node */
bpf_spin_unlock(&l);
What the verifier considers n to be after the push, and thus what can be
done with n, are changed by this patch.
Common properties both before/after this patch:
* After push, n is only a valid reference to the node until end of
critical section
* After push, n cannot be pushed to any list
* After push, the program can read the node's fields using n
Before:
* After push, n retains the ref_obj_id which it received on
bpf_obj_new, but the associated bpf_reference_state's
release_on_unlock field is set to true
* release_on_unlock field and associated logic is used to implement
"n is only a valid ref until end of critical section"
* After push, n cannot be written to, the node must be removed from
the list before writing to its fields
* After push, n is marked PTR_UNTRUSTED
After:
* After push, n's ref is released and ref_obj_id set to 0. NON_OWN_REF
type flag is added to reg's type, indicating that it's a non-owning
reference.
* NON_OWN_REF flag and logic is used to implement "n is only a
valid ref until end of critical section"
* n can be written to (except for special fields e.g. bpf_list_node,
timer, ...)
Summary of specific implementation changes to achieve the above:
* release_on_unlock field, ref_set_release_on_unlock helper, and logic
to "release on unlock" based on that field are removed
* The anonymous active_lock struct used by bpf_verifier_state is
pulled out into a named struct bpf_active_lock.
* NON_OWN_REF type flag is introduced along with verifier logic
changes to handle non-owning refs
* Helpers are added to use NON_OWN_REF flag to implement non-owning
ref semantics as described above
* invalidate_non_owning_refs - helper to clobber all non-owning refs
matching a particular bpf_active_lock identity. Replaces
release_on_unlock logic in process_spin_lock.
* ref_set_non_owning - set NON_OWN_REF type flag after doing some
sanity checking
* ref_convert_owning_non_owning - convert owning reference w/
specified ref_obj_id to non-owning references. Set NON_OWN_REF
flag for each reg with that ref_obj_id and 0-out its ref_obj_id
* Update linked_list selftests to account for minor semantic
differences introduced by this patch
* Writes to a release_on_unlock node ref are not allowed, while
writes to non-owning reference pointees are. As a result the
linked_list "write after push" failure tests are no longer scenarios
that should fail.
* The test##missing_lock##op and test##incorrect_lock##op
macro-generated failure tests need to have a valid node argument in
order to have the same error output as before. Otherwise
verification will fail early and the expected error output won't be seen.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Link: https://lore.kernel.org/r/20230212092715.1422619-2-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
If a device has a firmware node (DT/ACPI), and the device is marked
disabled, that is currently ignored. Add a check for this condition and
bail out creating the pci_dev.
This assumes the config space for the device can still be accessed because
they already have by this point in order to identify the device.
Link: https://lore.kernel.org/r/20230210164351.2687475-1-robh@kernel.org
Tested-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Liu Peibao <liupeibao@loongson.cn>
Cc: Huacai Chen <chenhuacai@loongson.cn>
|
|
Since commit ee6d3dd4ed48 ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definitions to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Loongson-2K SOC and LS7A2000 chipset add new PCI IDs that need MRRS
quirk. Add them.
Link: https://lore.kernel.org/r/20230211023321.3530080-1-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
ubiblock devices were previously only identifyable by their name, but
not connected to their parent UBI volume device e.g. in sysfs.
Properly parent ubiblock device as descendant of a UBI volume device
to reflect device model hierachy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Wire up the device parent pointer of UBI devices to their lower MTD
device, typically an MTD partition or whole-chip device.
The most noticeable change is that in sysfs, previously ubi devices
would be could in /sys/devices/virtual/ubi while after this change they
would be correctly attached to their parent MTD device, e.g.
/sys/devices/platform/1100d000.spi/spi_master/spi1/spi1.0/mtd/mtd2/ubi0.
Locating UBI devices using /sys/class/ubi/ of course still works as
well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
There are several architectures that duplicate definitions of
map_page_into_agp(), unmap_page_from_agp() and flush_agp_cache().
Define those in asm-generic/agp.h and use it instead of duplicated
per-architecture headers.
Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There is a copy of alloc_gatt_pages() and free_gatt_pages in several
architectures in arch/$ARCH/include/asm/agp.h. All the copies do exactly
the same: alias alloc_gatt_pages() to __get_free_pages(GFP_KERNEL) and
alias free_gatt_pages() to free_pages().
Define alloc_gatt_pages() and free_gatt_pages() in drivers/char/agp/agp.h
and drop per-architecture definitions.
Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pass the correct 'ce_gpio' to IS_ERR(), and remove the ce_gpio in
chip data, make it all by SW control only, not to control by HW pin.
Fixes: 4a1a5f6781d8 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The return value of max77650_charger_disable() is ignored by all but one
caller. That one caller propagates the error code in the platform driver's
remove function. The only effect of that is that the driver core emits
a generic error message (but still removes the device). As
max77650_charger_disable() already emits an error message, this can better
be changed to return zero.
This is a preparation for making struct platform_driver::remove return
void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
* irq/irqdomain-locking:
: .
: irqdomain locking overhaul courtesy of Johan Hovold.
:
: From the cover letter:
:
: "Parallel probing (e.g. due to asynchronous probing) of devices that
: share interrupts can currently result in two mappings for the same
: hardware interrupt to be created.
:
: This series fixes this mapping race and reworks the irqdomain locking so
: that in the end the global irq_domain_mutex is only used for managing
: the likewise global irq_domain_list, while domain operations (e.g. IRQ
: allocations) use per-domain (hierarchy) locking."
: .
irqdomain: Switch to per-domain locking
irqchip/mvebu-odmi: Use irq_domain_create_hierarchy()
irqchip/loongson-pch-msi: Use irq_domain_create_hierarchy()
irqchip/gic-v3-mbi: Use irq_domain_create_hierarchy()
irqchip/gic-v3-its: Use irq_domain_create_hierarchy()
irqchip/gic-v2m: Use irq_domain_create_hierarchy()
irqchip/alpine-msi: Use irq_domain_add_hierarchy()
x86/uv: Use irq_domain_create_hierarchy()
x86/ioapic: Use irq_domain_create_hierarchy()
irqdomain: Clean up irq_domain_push/pop_irq()
irqdomain: Drop leftover brackets
irqdomain: Drop dead domain-name assignment
irqdomain: Drop revmap mutex
irqdomain: Fix domain registration race
irqdomain: Fix mapping-creation race
irqdomain: Refactor __irq_domain_alloc_irqs()
irqdomain: Look for existing mapping only once
irqdomain: Drop bogus fwspec-mapping error handling
irqdomain: Fix disassociation race
irqdomain: Fix association race
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
