| Age | Commit message (Collapse) | Author |
|---|
|
Pull MIPS fixes from Ralf Baechle:
"Random fixes across the MIPS tree. The two hotspots are several bugs
in the module loader and the ath79 SOC support; also noteworthy is the
restructuring of the code to synchronize CPU timers across CPUs on
startup; the old code recently ceased to work due to unrelated
changes.
All except one of these patches have sat for a significant time in
linux-next for testing."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: pci-ar724x: avoid data bus error due to a missing PCIe module
MIPS: Malta: Delete duplicate PCI fixup.
MIPS: ath79: don't hardcode the unavailability of the DSP ASE
MIPS: Synchronize MIPS count one CPU at a time
MIPS: BCM63xx: Fix SPI message control register handling for BCM6338/6348.
MIPS: Module: Deal with malformed HI16/LO16 relocation sequences.
MIPS: Fix race condition in module relocation code.
MIPS: Fix memory leak in error path of HI16/LO16 relocation handling.
MIPS: MTX-1: Add udelay to mtx1_pci_idsel
MIPS: ath79: select HAVE_CLK
MIPS: ath79: Use correct IRQ number for the OHCI controller on AR7240
MIPS: ath79: Fix number of GPIO lines for AR724[12]
MIPS: Octeon: Fix broken interrupt controller code.
|
|
Pull nfsd bugfixes from J. Bruce Fields:
"Particular thanks to Michael Tokarev, Malahal Naineni, and Jamie
Heilman for their testing and debugging help."
* 'for-3.6' of git://linux-nfs.org/~bfields/linux:
svcrpc: fix svc_xprt_enqueue/svc_recv busy-looping
svcrpc: sends on closed socket should stop immediately
svcrpc: fix BUG() in svc_tcp_clear_pages
nfsd4: fix security flavor of NFSv4.0 callback
|
|
Pull block-related fixes from Jens Axboe:
- Improvements to the buffered and direct write IO plugging from
Fengguang.
- Abstract out the mapping of a bio in a request, and use that to
provide a blk_bio_map_sg() helper. Useful for mapping just a bio
instead of a full request.
- Regression fix from Hugh, fixing up a patch that went into the
previous release cycle (and marked stable, too) attempting to prevent
a loop in __getblk_slow().
- Updates to discard requests, fixing up the sizing and how we align
them. Also a change to disallow merging of discard requests, since
that doesn't really work properly yet.
- A few drbd fixes.
- Documentation updates.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: replace __getblk_slow misfix by grow_dev_page fix
drbd: Write all pages of the bitmap after an online resize
drbd: Finish requests that completed while IO was frozen
drbd: fix drbd wire compatibility for empty flushes
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update missing index files in block/00-INDEX
block: move down direct IO plugging
block: remove plugging at buffered write time
block: disable discard request merge temporarily
bio: Fix potential memory leak in bio_find_or_create_slab()
block: Don't use static to define "void *p" in show_partition_start()
block: Add blk_bio_map_sg() helper
block: Introduce __blk_segment_map_sg() helper
fs/block-dev.c:fix performance regression in O_DIRECT writes to md block devices
block: split discard into aligned requests
block: reorganize rounding of max_discard_sectors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
- libata-acpi regression fix
- additional or corrected drive quirks for ata_blacklist
- Kconfig text tweaking
- new PCI IDs
- pata_atiixp: quirk for MSI motherboard
- export ahci_dev_classify for an ahci_platform driver
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Add a space to " 2GB ATA Flash Disk" DMA blacklist entry
[libata] new quirk, lift bridge limits for Buffalo DriveStation Quattro
[libata] Kconfig: Elaborate that SFF is meant for legacy and PATA stuff
[libata] acpi: call ata_acpi_gtm during ata port init time
ata_piix: Add Device IDs for Intel Lynx Point-LP PCH
ahci: Add Device IDs for Intel Lynx Point-LP PCH
pata_atiixp: override cable detection on MSI E350DM-E33
ahci: un-staticize ahci_dev_classify
|
|
commit d70e551c8e1ecb6f20422f8db6bfe6a0049edcb8, Add " 2GB ATA Flash
Disk"/"ADMA428M" to DMA blacklist, should have added a space before 2GB.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
With !HIGHMEM, sanity_check_meminfo checks for banks that completely or
partially overlap the vmalloc region. The test for partial overlap checks
__va(bank->start + bank->size) > vmalloc_min. This is not appropriate if
there is a non-linear translation between virtual and physical addresses,
as bank->start + bank->size is actually in the bank following the one being
interrogated.
In most cases, even when using SPARSEMEM, this is not problematic as the
subsequent bank will start at a higher va than the one in question. However
if the physical to virtual address conversion is not monotonic increasing,
the incorrect test could result in a bank not being truncated when it
should be.
This patch ensures we perform the va-pa conversion on memory from the
bank we are interested in, not the following one.
Reported-by: ??? (Steve) <zhanzhenbo@gmail.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
LPAE does not use two pmd entries for a pte, so the additional tlb
flushing is not required.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The bfi instruction is not available on ARMv6, so instead use an and/orr
sequence in the contextidr_notifier. This gets rid of the assembler
error:
Assembler messages:
Error: selected processor does not support ARM mode `bfi r3,r2,#0,#8'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When enabling the MMU for ARMv7 CPUs, the decompressor does not touch
the ttbcr register, assuming that it will be zeroed (N == 0, EAE == 0).
Given that only EAE is defined as 0 for non-secure copies of the
register (and a bootloader such as kexec may leave it set to 1 anyway),
we should ensure that we reset the register ourselves before turning on
the MMU.
This patch zeroes TTBCR.EAE and TTBCR.N prior to enabling the MMU for
ARMv7 cores in the decompressor, configuring us exclusively for 32-bit
translation tables via TTBR0.
Cc: <stable@vger.kernel.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Breakpoint validation currently fails for single-byte watchpoints on
addresses ending in 11b. There is no reason to forbid such a watchpoint,
so extend the validation code to allow it.
Cc: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
From ARM debug architecture v7.1 onwards, a watchpoint exception causes
the DFAR to be updated with the faulting data address. However, DFSR.WnR
takes an UNKNOWN value and therefore cannot be used in general to
determine the access type that triggered the watchpoint.
This patch forbids watchpoints without an overflow handler from
specifying a specific access type (load/store). Those with overflow
handlers must be able to handle false positives potentially triggered by
a watchpoint of a different access type on the same address. For
SIGTRAP-based handlers (i.e. ptrace), this should have no impact.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Murali Nalajala reports a regression that ioremapping address zero
results in an oops dump:
Unable to handle kernel paging request at virtual address fa200000
pgd = d4f80000
[fa200000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 Tainted: G W (3.4.0-g3b5f728-00009-g638207a #13)
PC is at msm_pm_config_rst_vector_before_pc+0x8/0x30
LR is at msm_pm_boot_config_before_pc+0x18/0x20
pc : [<c0078f84>] lr : [<c007903c>] psr: a0000093
sp : c0837ef0 ip : cfe00000 fp : 0000000d
r10: da7efc17 r9 : 225c4278 r8 : 00000006
r7 : 0003c000 r6 : c085c824 r5 : 00000001 r4 : fa101000
r3 : fa200000 r2 : c095080c r1 : 002250fc r0 : 00000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 25180059 DAC: 00000015
[<c0078f84>] (msm_pm_config_rst_vector_before_pc+0x8/0x30) from [<c007903c>] (msm_pm_boot_config_before_pc+0x18/0x20)
[<c007903c>] (msm_pm_boot_config_before_pc+0x18/0x20) from [<c007a55c>] (msm_pm_power_collapse+0x410/0xb04)
[<c007a55c>] (msm_pm_power_collapse+0x410/0xb04) from [<c007b17c>] (arch_idle+0x294/0x3e0)
[<c007b17c>] (arch_idle+0x294/0x3e0) from [<c000eed8>] (default_idle+0x18/0x2c)
[<c000eed8>] (default_idle+0x18/0x2c) from [<c000f254>] (cpu_idle+0x90/0xe4)
[<c000f254>] (cpu_idle+0x90/0xe4) from [<c057231c>] (rest_init+0x88/0xa0)
[<c057231c>] (rest_init+0x88/0xa0) from [<c07ff890>] (start_kernel+0x3a8/0x40c)
Code: c0704256 e12fff1e e59f2020 e5923000 (e5930000)
This is caused by the 'reserved' entries which we insert (see
19b52abe3c5d7 - ARM: 7438/1: fill possible PMD empty section gaps)
which get matched for physical address zero.
Resolve this by marking these reserved entries with a different flag.
Cc: <stable@vger.kernel.org>
Tested-by: Murali Nalajala <mnalajal@codeaurora.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The GPIO buttons are named SW3, SW4, SW5 and SW6 on the board
silkscreen. Update the buttons descriptions accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
This is an initial merge in of Eric Biederman's work to start adding
user namespace support to the networking.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
1. Change the TX path to stop queues earlier and avoid returning
NETDEV_TX_BUSY.
2. Remove some inefficiencies in soft-TSO.
3. Fix various bugs involving device state transitions and/or reset
scheduling by error handlers.
4. Take advantage of my previous change to operstate initialisation.
5. Miscellaneous cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Hutchings says:
====================
Simple fix for a braino. Please also queue this for the 3.4 and 3.5
stable series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
here are two fixes for the v3.6 release cycle. Alexey Khoroshilov submitted a
fix for a memory leak in the softing driver (in softing_load_fw()) in case a
krealloc() fails. Sven Schmitt fixed the misuse of the IRQF_SHARED flag in the
irq resouce of the sja1000 platform driver, now the correct flag is used. There
are no mainline users of this feature which need to be converted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
This is a batch of updates intended for 3.7. The bulk of it is
mac80211 changes, including some mesh work from Thomas Pederson and
some multi-channel work from Johannes. A variety of driver updates
and other bits are scattered in there as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
This batch of fixes is intended for 3.6...
Johannes Berg gives us a pair of iwlwifi fixes. One corrects some
improperly defined ifdefs that lead to crashes and BUG_ONs. The other
prevents attempts to read SRAM for devices that aren't actually started.
Julia Lawall provides an ipw2100 fix to properly set the return code
from a function call before testing it! :-)
Thomas Huehn corrects the improper use of a constant related to a power
setting in ath5k.
Thomas Pedersen offers a mac80211 fix to properly handle destination
addresses of unicast frames passing though a mesh gate.
Vladimir Zapolskiy provides a brcmsmac fix to properly mark the
interface state when the device goes down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following commit 8f4cccb ('net: Set device operstate at registration
time') it is now correct and preferable to set the carrier off before
registering a device.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We also stop clearing *efx in efx_init_struct(). This is safe because
alloc_etherdev_mq() already clears it for us.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
RX DMA is limited by the length specified in each descriptor and not
by the MAC. Over-length frames may get into the RX FIFO regardless of
the MAC settings, due to a hardware bug, but they will be truncated by
the packet DMA engine and reported as such in the completion event.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We try to defer resets while the device is not READY, but we're not
doing this quite correctly. In particular, changes to efx_nic::state
are documented as serialised by the RTNL lock, but they aren't.
1. We check whether a reset was requested during probe (suggesting
broken hardware) before we allow requested resets to be scheduled.
This leaves a window where a requested reset would be deferred
indefinitely.
2. Although we cancel the reset work item during device removal,
there are still later operations that can cause it to be scheduled
again. We need to check the state before scheduling it.
3. Since the state can change between scheduling and running of
the work item, we still need to check it there, and we need to
do so *after* acquiring the RTNL lock which serialises state
changes.
4. We must cancel the reset work item during device removal, if the
state could ever have been READY. This wasn't done in some of the
failure paths from efx_pci_probe(). Move the cancellation to
efx_pci_remove_main().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The current informational message doesn't properly explain what
happens, and could also appear if we defer a reset during
suspend/resume.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
efx_change_mtu() and efx_realloc_channels() each stop and start much
of the NIC, even if it has been disabled. Since efx_start_all() is a
no-op when the NIC is disabled, this is probably harmless in the case
of efx_change_mtu(), but efx_realloc_channels() also reenables
interrupts which could be a bad thing to do.
Change efx_start_all() and efx_start_interrupts() to assert that the
NIC is not disabled, but make efx_stop_interrupts() do nothing if the
NIC is disabled (since it is already stopped), consistent with
efx_stop_all().
Update comments for efx_start_all() and efx_stop_all() to describe
their purpose and preconditions more accurately.
Add a common function to check and log if the NIC is disabled, and use
it in efx_net_open(), efx_change_mtu() and efx_realloc_channels().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Interrupt state should be consistently guarded by the RTNL lock once
the net device is registered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Currently we ignore and clear the disabled state.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
I don't think these PM functions can race with userland net device
operations, but it's much easier to reason about locking if state is
consistently guarded by the same lock.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
STATE_INIT and STATE_FINI are equivalent and represent incompletely
initialised states; combine them as STATE_UNINIT.
Rename STATE_RUNNING to STATE_READY, to avoid confusion with
netif_running() and IFF_RUNNING.
The comments do not quite match current usage, but this will be
corrected in subsequent fixes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We only use tso_state::full_packet_space to calculate the IPv4 tot_len
or IPv6 payload_len, not to set tso_state::packet_space. Replace it
with an ip_base_len field holding the value of tot_len or payload_len
before including the TCP payload, which is much more useful when
constructing the new headers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
TSO header buffers contain a control structure immediately followed by
the packet headers, and are kept on a free list when not in use. This
complicates buffer management and tends to result in cache read misses
when we recycle such buffers (particularly if DMA-coherent memory
requires caches to be disabled).
Replace the free list with a simple mapping by descriptor index. We
know that there is always a payload descriptor between any two
descriptors with TSO header buffers, so we can allocate only one
such buffer for each two descriptors.
While we're at it, use a standard error code for allocation failure,
not -1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We now have a definite upper bound on the number of descriptors per
skb; use that to stop the queue when the next packet might not fit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Add a flags field to struct efx_tx_buffer, replacing the
continuation and map_single booleans.
Since a single descriptor cannot be both a TSO header and the last
descriptor for an skb, unionise efx_tx_buffer::{skb,tsoh} and add
flags for validity of these fields.
Clear all flags in free buffers (whereas previously the continuation
flag would be set).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The cwnd reduction in fast recovery is based on the number of packets
newly delivered per ACK. For non-sack connections every DUPACK
signifies a packet has been delivered, but the sender mistakenly
skips counting them for cwnd reduction.
The fix is to compute newly_acked_sacked after DUPACKs are accounted
in sacked_out for non-sack connections.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
also, remove unused vlan_info definition from header
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When no one is listening on NL socket, -ESRCH is returned and warning
message is printed. This message is confusing people and in fact has no
meaning. So do not print it in this case.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Non-root user-space processes can send Netlink messages to other
processes that are well-known for being subscribed to Netlink
asynchronous notifications. This allows ilegitimate non-root
process to send forged messages to Netlink subscribers.
The userspace process usually verifies the legitimate origin in
two ways:
a) Socket credentials. If UID != 0, then the message comes from
some ilegitimate process and the message needs to be dropped.
b) Netlink portID. In general, portID == 0 means that the origin
of the messages comes from the kernel. Thus, discarding any
message not coming from the kernel.
However, ctnetlink sets the portID in event messages that has
been triggered by some user-space process, eg. conntrack utility.
So other processes subscribed to ctnetlink events, eg. conntrackd,
know that the event was triggered by some user-space action.
Neither of the two ways to discard ilegitimate messages coming
from non-root processes can help for ctnetlink.
This patch adds capability validation in case that dst_pid is set
in netlink_sendmsg(). This approach is aggressive since existing
applications using any Netlink bus to deliver messages between
two user-space processes will break. Note that the exception is
NETLINK_USERSOCK, since it is reserved for netlink-to-netlink
userspace communication.
Still, if anyone wants that his Netlink bus allows netlink-to-netlink
userspace, then they can set NL_NONROOT_SEND. However, by default,
I don't think it makes sense to allow to use NETLINK_ROUTE to
communicate two processes that are sending no matter what information
that is not related to link/neighbouring/routing. They should be using
NETLINK_USERSOCK instead for that.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using eth_hw_addr_random() to generate a random Ethernet address
(MAC) to be used by a net device and set addr_assign_type.
Not need to duplicating its implementation.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using eth_hw_addr_random() to generate a random Ethernet address
(MAC) to be used by a net device and set addr_assign_type.
Not need to duplicating its implementation.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The operstate of a device is initially IF_OPER_UNKNOWN and is updated
asynchronously by linkwatch after each change of carrier state
reported by the driver. The default carrier state of a net device is
on, and this will never be changed on drivers that do not support
carrier detection, thus the operstate remains IF_OPER_UNKNOWN.
For devices that do support carrier detection, the driver must set the
carrier state to off initially, then poll the hardware state when the
device is opened. However, we must not activate linkwatch for a
unregistered device, and commit b473001 ('net: Do not fire linkwatch
events until the device is registered.') ensured that we don't. But
this means that the operstate for many devices that support carrier
detection remains IF_OPER_UNKNOWN when it should be IF_OPER_DOWN.
The same issue exists with the dormant state.
The proper initialisation sequence, avoiding a race with opening of
the device, is:
rtnl_lock();
rc = register_netdevice(dev);
if (rc)
goto out_unlock;
netif_carrier_off(dev); /* or netif_dormant_on(dev) */
rtnl_unlock();
but it seems silly that this should have to be repeated in so many
drivers. Further, the operstate seen immediately after opening the
device may still be IF_OPER_UNKNOWN due to the asynchronous nature of
linkwatch.
Commit 22604c8 ('net: Fix for initial link state in 2.6.28') attempted
to fix this by setting the operstate synchronously, but it was
reverted as it could lead to deadlock.
This initialises the operstate synchronously at registration time
only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to fsl_pq_mdio.c, this driver is for the 10G MDIO controller on
Freescale Frame Manager Ethernet controllers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network classifier cgroup initalizes each cgroups instance classid value to
0. However, the sock_update_classid function only updates classid's in sockets
if the tasks cgroup classid is not zero, and if it differs from the current
classid. The later check is to prevent cache line dirtying, but the former is
detrimental, as it prevents resetting a classid for a cgroup to 0. While this
is not a common action, it has administrative usefulness (if the admin wants to
disable classification of a certain group temporarily for instance).
Easy fix, just remove the zero check. Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
Multicast traffic allocates dst with DST_NOCACHE, but dst is
not inserted into rt_uncached_list.
This slowdown multicast workloads on SMP because rt_uncached_lock is
contended.
Change the test before taking the lock to actually check the dst
was inserted into rt_uncached_list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
