| Age | Commit message (Collapse) | Author |
|---|
|
Chip select pinctrl phandle was missing in several stm32mp15x based boards.
Fixes: ea99a5a02ebc ("ARM: dts: stm32: Create separate pinmux for qspi cs pin in stm32mp15-pinctrl.dtsi")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
IO mux selection is configured in PMU_GRF_SOC_CON4 and GRF_IOFUNC_SEL0-5
regs on RK3568. pwm0-2 is configured in PMU_GRF reg and the rest is
configured in GRF_IOFUNC regs according to TRM [1].
Update mux route data to reflect this and use proper detection pin for
UART1 IO mux M1.
This fixes HDMITX IO mux M1 selection and makes it possible to enable
HDMI CEC on my Radxa ROCK 3 Model A v1.31 board.
[1] http://opensource.rock-chips.com/images/2/26/Rockchip_RK3568_TRM_Part1_V1.3-20220930P.PDF
Fixes: c0dadc0e47a8 ("pinctrl: rockchip: add support for rk3568")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230110084636.1141740-1-jonas@kwiboo.se
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In a number of cases the driver assigns a default value of -1 to
priv->plat->phy_addr. This may result in calling mdiobus_get_phy()
with addr parameter being -1. Therefore check for this scenario and
bail out before calling mdiobus_get_phy().
Fixes: 42e87024f727 ("net: stmmac: Fix case when PHY handle is not present")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/669f9671-ecd1-a41b-2727-7b73e3003985@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Acer Aspire 4810T predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native backlight interface which does
work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The previous ACPICA development list address, devel@acpica.org, started
to bounce some time ago and it is not likely to be restored, so replace
it with a new one, acpica-devel@lists.linuxfoundation.org.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a check for empty report_list in bigben_probe().
The missing check causes a type confusion when issuing a list_entry()
on an empty report_list.
The problem is caused by the assumption that the device must
have valid report_list. While this will be true for all normal HID
devices, a suitably malicious device can violate the assumption.
Fixes: 256a90ed9e46 ("HID: hid-bigbenff: driver for BigBen Interactive PS3OFMINIPAD gamepad")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add a check for empty report_list in hid_validate_values().
The missing check causes a type confusion when issuing a list_entry()
on an empty report_list.
The problem is caused by the assumption that the device must
have valid report_list. While this will be true for all normal HID
devices, a suitably malicious device can violate the assumption.
Fixes: 1b15d2e5b807 ("HID: core: fix validation of report id 0")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The caller may pass any value as addr, what may result in an out-of-bounds
access to array mdio_map. One existing case is stmmac_init_phy() that
may pass -1 as addr. Therefore validate addr before using it.
Fixes: 7f854420fbfe ("phy: Add API for {un}registering an mdio device to a bus.")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/cdf664ea-3312-e915-73f8-021678d08887@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Packet len computed as difference of length word extracted from
skb data and four may result in a negative value. In such case
processing of the buffer should be interrupted rather than
setting sr_skb->len to an unexpectedly large value (due to cast
from signed to unsigned integer) and passing sr_skb to
usbnet_skb_return.
Fixes: e9da0b56fe27 ("sr9700: sanity check for packet length")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230114182326.30479-1-szymon.heidrich@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When exception is triggered, code flow go handle_\exception in some
cases. One of stackframe in this case as follows,
high -> +-------+
| REGS | <- a pt_regs
| |
| | <- ex trigger
| REGS | <- ex pt_regs <-+
| | |
| | |
low -> +-------+ ->unwind-+
When unwinder unwinds to handler_\exception it cannot go on prologue
analysis. Because it is an asynchronous code flow, we should get the
next frame PC from regs->csr_era rather than regs->regs[1]. At init time
we copy the handlers to eentry and also copy them to NUMA-affine memory
named pcpu_handlers if NUMA is enabled. Thus, unwinder cannot unwind
normally. To solve this, we try to give some hints in handler_\exception
and fixup unwinders in unwind_next_frame().
Reported-by: Qing Zhang <zhangqing@loongson.cn>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The prolugue unwinder rely on symbol info. When PC is not in kernel text
address, it cannot find relative symbol info and it will be broken. The
guess unwinder will be used in this case. And the guess unwinder code in
prolugue unwinder is redundant. Strip it out and set the unwinder type
in unwind_state. Make guess_unwinder::unwind_next_frame() as default way
when other unwinders cannot unwind in some extreme case.
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The stack frame when function_graph enable like follows,
--------- <- function sp_on_entry
|
|
|
FAKE_RA <- sp_on_entry - sizeof(pt_regs) + PT_R1
|
--------- <- sp_on_entry - sizeof(pt_regs)
So if we want to get the &FAKE_RA we should get sp_on_entry first. In
the unwinder_prologue case, we can get the sp_on_entry as state->sp,
because we try to calculate each CFA and the ra saved address. But in
the unwinder_guess case, we cannot get it because we do not try to
calculate the CFA. Although LoongArch have not fixed frame, the $ra is
saved at CFA - 8 in most cases, we can try guess, too. As we store the
pc in state, we not need to dereference state->sp, too.
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
At unwind_start(), it is better to get its frame info here rather than
get them outside, even we don't have 'regs'. In this way we can simply
use unwind_{start, next_frame, done} outside.
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
When state->first is not set, the PC is a return address in the previous
frame. We need to adjust its value in case overflow to the next symbol.
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Simplify larch_insn_gen_xxx implementation by reusing emit_xxx.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
There exists a common function sign_extend64() to sign extend a 64-bit
value using specified bit as sign-bit in include/linux/bitops.h, it is
more efficient, let us use it and remove the arch-specific sign_extend()
under arch/loongarch.
Suggested-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
HWCAP_LOONGARCH_CPUCFG is missing in elf_hwcap, so add it for glibc's
later use.
Cc: stable@vger.kernel.org
Reported-by: Yinyu Cai <caiyinyu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
If the policy defines pd_online_fn(), it should be called after
pd_init_fn(), like blkg_create().
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230103112833.2013432-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"21 hotfixes. Thirteen of these address pre-6.1 issues and hence have
the cc:stable tag"
* tag 'mm-hotfixes-stable-2023-01-16-15-23' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
init/Kconfig: fix typo (usafe -> unsafe)
nommu: fix split_vma() map_count error
nommu: fix do_munmap() error path
nommu: fix memory leak in do_mmap() error path
MAINTAINERS: update Robert Foss' email address
proc: fix PIE proc-empty-vm, proc-pid-vm tests
mm: update mmap_sem comments to refer to mmap_lock
include/linux/mm: fix release_pages_arg kernel doc comment
lib/win_minmax: use /* notation for regular comments
kasan: mark kasan_kunit_executing as static
nilfs2: fix general protection fault in nilfs_btree_insert()
Docs/admin-guide/mm/zswap: remove zsmalloc's lack of writeback warning
mm/hugetlb: pre-allocate pgtable pages for uffd wr-protects
hugetlb: unshare some PMDs when splitting VMAs
mm: fix vma->anon_name memory leak for anonymous shmem VMAs
mm/shmem: restore SHMEM_HUGE_DENY precedence over MADV_COLLAPSE
mm/MADV_COLLAPSE: don't expand collapse when vm_end is past requested end
mm/userfaultfd: enable writenotify while userfaultfd-wp is enabled for a VMA
mm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma
mm/hugetlb: fix uffd-wp handling for migration entries in hugetlb_change_protection()
...
|
|
If we have one task trying to start the quota rescan worker while another
one is trying to disable quotas, we can end up hitting a race that results
in the quota rescan worker doing a NULL pointer dereference. The steps for
this are the following:
1) Quotas are enabled;
2) Task A calls the quota rescan ioctl and enters btrfs_qgroup_rescan().
It calls qgroup_rescan_init() which returns 0 (success) and then joins a
transaction and commits it;
3) Task B calls the quota disable ioctl and enters btrfs_quota_disable().
It clears the bit BTRFS_FS_QUOTA_ENABLED from fs_info->flags and calls
btrfs_qgroup_wait_for_completion(), which returns immediately since the
rescan worker is not yet running.
Then it starts a transaction and locks fs_info->qgroup_ioctl_lock;
4) Task A queues the rescan worker, by calling btrfs_queue_work();
5) The rescan worker starts, and calls rescan_should_stop() at the start
of its while loop, which results in 0 iterations of the loop, since
the flag BTRFS_FS_QUOTA_ENABLED was cleared from fs_info->flags by
task B at step 3);
6) Task B sets fs_info->quota_root to NULL;
7) The rescan worker tries to start a transaction and uses
fs_info->quota_root as the root argument for btrfs_start_transaction().
This results in a NULL pointer dereference down the call chain of
btrfs_start_transaction(). The stack trace is something like the one
reported in Link tag below:
general protection fault, probably for non-canonical address 0xdffffc0000000041: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000208-0x000000000000020f]
CPU: 1 PID: 34 Comm: kworker/u4:2 Not tainted 6.1.0-syzkaller-13872-gb6bb9676f216 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Workqueue: btrfs-qgroup-rescan btrfs_work_helper
RIP: 0010:start_transaction+0x48/0x10f0 fs/btrfs/transaction.c:564
Code: 48 89 fb 48 (...)
RSP: 0018:ffffc90000ab7ab0 EFLAGS: 00010206
RAX: 0000000000000041 RBX: 0000000000000208 RCX: ffff88801779ba80
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: dffffc0000000000 R08: 0000000000000001 R09: fffff52000156f5d
R10: fffff52000156f5d R11: 1ffff92000156f5c R12: 0000000000000000
R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2bea75b718 CR3: 000000001d0cc000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
btrfs_qgroup_rescan_worker+0x3bb/0x6a0 fs/btrfs/qgroup.c:3402
btrfs_work_helper+0x312/0x850 fs/btrfs/async-thread.c:280
process_one_work+0x877/0xdb0 kernel/workqueue.c:2289
worker_thread+0xb14/0x1330 kernel/workqueue.c:2436
kthread+0x266/0x300 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
</TASK>
Modules linked in:
So fix this by having the rescan worker function not attempt to start a
transaction if it didn't do any rescan work.
Reported-by: syzbot+96977faa68092ad382c4@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/000000000000e5454b05f065a803@google.com/
Fixes: e804861bd4e6 ("btrfs: fix deadlock between quota disable and qgroup rescan worker")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
During lseek, for SEEK_DATA and SEEK_HOLE modes, we access the disk_bytenr
of an extent without checking its type. However inline extents have their
data starting the offset of the disk_bytenr field, so accessing that field
when we have an inline extent can result in either of the following:
1) Interpret the inline extent's data as a disk_bytenr value;
2) In case the inline data is less than 8 bytes, we access part of some
other item in the leaf, or unused space in the leaf;
3) In case the inline data is less than 8 bytes and the extent item is
the first item in the leaf, we can access beyond the leaf's limit.
So fix this by not accessing the disk_bytenr field if we have an inline
extent.
Fixes: b6e833567ea1 ("btrfs: make hole and data seeking a lot more efficient")
Reported-by: Matthias Schoepfer <matthias.schoepfer@googlemail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216908
Link: https://lore.kernel.org/linux-btrfs/7f25442f-b121-2a3a-5a3d-22bcaae83cd4@leemhuis.info/
CC: stable@vger.kernel.org # 6.1
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
write_one_page is an awkward interface that expects the page locked and
->writepage to be implemented. Replace that by zeroing the signature
bytes and synchronize the block device page using the proper bdev
helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_scratch_superblocks open codes scratching super block of a
non-zoned super block. Split the code to read, zero and write the
superblock for regular devices into a separate helper.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Another batch of fixes, dealing with fallouts from 6.1 reported by
users:
- tree-log fixes:
- fix directory logging due to race with concurrent index key
deletion
- fix missing error handling when logging directory items
- handle case of conflicting inodes being added to the log
- remove transaction aborts for not so serious errors
- fix qgroup accounting warning when rescan can be started at time
with temporarily disable accounting
- print more specific errors to system log when device scan ioctl
fails
- disable space overcommit for ZNS devices, causing heavy performance
drop"
* tag 'for-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: do not abort transaction on failure to update log root
btrfs: do not abort transaction on failure to write log tree when syncing log
btrfs: add missing setup of log for full commit at add_conflicting_inode()
btrfs: fix directory logging due to race with concurrent index key deletion
btrfs: fix missing error handling when logging directory items
btrfs: zoned: enable metadata over-commit for non-ZNS setup
btrfs: qgroup: do not warn on record without old_roots populated
btrfs: add extra error messages to cover non-ENOMEM errors from device_add_list()
|
|
The last_pg is wrong, it is actually the first page of the last
scatterlist element. To get the last page of the last scatterlist element
we have to add prv->length. So it is checking mergability against the
wrong page, Further, a SG element is not guaranteed to end on a page
boundary, so we have to check the sub page location also for merge
eligibility.
Fix the above by checking physical contiguity based on PFNs, compute the
actual last page and then call pages_are_mergable().
Fixes: 1567b49d1a40 ("lib/scatterlist: add check when merging zone device pages")
Link: https://lore.kernel.org/r/20230111101054.188136-1-yishaih@nvidia.com
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Fix W=1 kernel-doc warning:
kernel/printk/printk.c:
- Include function parameter in console_lock_spinning_disable_and_check()
Signed-off-by: Anuradha Weeraman <anuradha@debian.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230116125635.374567-1-anuradha@debian.org
|
|
The revert of the removal of this driver happened after we fixed up
the split limits for NOWAIT issue, hence it got missed. Ensure that
we check for a NULL bio after splitting, in case it should be retried.
Marking this as fixing both commits, so that stable backport will do
this correctly.
Cc: stable@vger.kernel.org
Fixes: 9cea62b2cbab ("block: don't allow splitting of a REQ_NOWAIT bio")
Fixes: 4b83e99ee709 ("Revert "pktcdvd: remove driver."")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Several mutexes are taken while setting up console serial ports. In
particular, the tty_port->mutex and @console_mutex are taken:
serial_pnp_probe
serial8250_register_8250_port
uart_add_one_port (locks tty_port->mutex)
uart_configure_port
register_console (locks @console_mutex)
In order to synchronize kgdb's tty_find_polling_driver() with
register_console(), commit 6193bc90849a ("tty: serial: kgdboc:
synchronize tty_find_polling_driver() and register_console()") takes
the @console_mutex. However, this leads to the following call chain
(with locking):
platform_probe
kgdboc_probe
configure_kgdboc (locks @console_mutex)
tty_find_polling_driver
uart_poll_init (locks tty_port->mutex)
uart_set_options
This is clearly deadlock potential due to the reverse lock ordering.
Since uart_set_options() requires holding @console_mutex in order to
serialize early initialization of the serial-console lock, take the
@console_mutex in uart_poll_init() instead of configure_kgdboc().
Since configure_kgdboc() was using @console_mutex for safe traversal
of the console list, change it to use the SRCU iterator instead.
Add comments to uart_set_options() kerneldoc mentioning that it
requires holding @console_mutex (aka the console_list_lock).
Fixes: 6193bc90849a ("tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
[pmladek@suse.com: Export console_srcu_read_lock_is_held() to fix build kgdboc as a module.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230112161213.1434854-1-john.ogness@linutronix.de
|
|
This reverts commit 13e5afd3d773c6fc6ca2b89027befaaaa1ea7293.
ieee80211_if_free() is already called from free_netdev(ndev)
because ndev->priv_destructor == ieee80211_if_free
syzbot reported:
general protection fault, probably for non-canonical address 0xdffffc0000000004: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
CPU: 0 PID: 10041 Comm: syz-executor.0 Not tainted 6.2.0-rc2-syzkaller-00388-g55b98837e37d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
RIP: 0010:pcpu_get_page_chunk mm/percpu.c:262 [inline]
RIP: 0010:pcpu_chunk_addr_search mm/percpu.c:1619 [inline]
RIP: 0010:free_percpu mm/percpu.c:2271 [inline]
RIP: 0010:free_percpu+0x186/0x10f0 mm/percpu.c:2254
Code: 80 3c 02 00 0f 85 f5 0e 00 00 48 8b 3b 48 01 ef e8 cf b3 0b 00 48 ba 00 00 00 00 00 fc ff df 48 8d 78 20 48 89 f9 48 c1 e9 03 <80> 3c 11 00 0f 85 3b 0e 00 00 48 8b 58 20 48 b8 00 00 00 00 00 fc
RSP: 0018:ffffc90004ba7068 EFLAGS: 00010002
RAX: 0000000000000000 RBX: ffff88823ffe2b80 RCX: 0000000000000004
RDX: dffffc0000000000 RSI: ffffffff81c1f4e7 RDI: 0000000000000020
RBP: ffffe8fffe8fc220 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000000 R11: 1ffffffff2179ab2 R12: ffff8880b983d000
R13: 0000000000000003 R14: 0000607f450fc220 R15: ffff88823ffe2988
FS: 00007fcb349de700(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b32220000 CR3: 000000004914f000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
netdev_run_todo+0x6bf/0x1100 net/core/dev.c:10352
ieee80211_register_hw+0x2663/0x4040 net/mac80211/main.c:1411
mac80211_hwsim_new_radio+0x2537/0x4d80 drivers/net/wireless/mac80211_hwsim.c:4583
hwsim_new_radio_nl+0xa09/0x10f0 drivers/net/wireless/mac80211_hwsim.c:5176
genl_family_rcv_msg_doit.isra.0+0x1e6/0x2d0 net/netlink/genetlink.c:968
genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline]
genl_rcv_msg+0x4ff/0x7e0 net/netlink/genetlink.c:1065
netlink_rcv_skb+0x165/0x440 net/netlink/af_netlink.c:2564
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1330 [inline]
netlink_unicast+0x547/0x7f0 net/netlink/af_netlink.c:1356
netlink_sendmsg+0x91b/0xe10 net/netlink/af_netlink.c:1932
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xd3/0x120 net/socket.c:734
____sys_sendmsg+0x712/0x8c0 net/socket.c:2476
___sys_sendmsg+0x110/0x1b0 net/socket.c:2530
__sys_sendmsg+0xf7/0x1c0 net/socket.c:2559
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 13e5afd3d773 ("wifi: mac80211: fix memory leak in ieee80211_if_add()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Zhengchao Shao <shaozhengchao@huawei.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113124326.3533978-1-edumazet@google.com
|
|
When adding WED support, mt76_dma_add_buf was accidentally changed to set
the skip_buf0 flag for tx buffers on the wrong queue descriptor entry.
Additionally, there is a rxwi leak when rx buffer allocation fails.
Fix this and make the code more readable by adding a separate function for
adding rx buffers.
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Link: https://lore.kernel.org/r/CABXGCsMEnQd=gYKTd1knRsWuxCb=Etv5nAre%2BXJS_s5FgVteYA@mail.gmail.com/
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216829
Reported-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/lkml/20230112171706.294550-1-angelogioacchino.delregno@collabora.com/
Fixes: cd372b8c99c5 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113105848.34642-3-nbd@nbd.name
|
|
Take into account possible error conditions of mt76_rx_token_consume
routine in mt7915_mmio_wed_init_rx_buf() and mt76_dma_add_buf()
Fixes: cd372b8c99c5 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Fixes: 4f831d18d12d ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 96f134dc19645be4994e89a2f68fa89309becbee)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113105848.34642-2-nbd@nbd.name
|
|
Do not increment queue head if mt76_dma_add_buf fails for Wireless
Ethernet Dispatcher rx queues.
Fixes: cd372b8c99c5 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit fe13dad8992be0b26c1be390bcd111acf9892c17)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113105848.34642-1-nbd@nbd.name
|
|
... to avoid the mess of conditional preprocessing as we are continually
adding fscache related mount options.
Reviewd-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230112065431.124926-3-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
Since the EROFS share domain feature for fscache mode has been available
since Linux v6.1, let's add documentation for 'domain_id' mount option.
Cc: linux-doc@vger.kernel.org
Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com>
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230112065431.124926-2-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
Using GFP_KERNEL in preemption disable context, causing below warning
when CONFIG_DEBUG_ATOMIC_SLEEP is enabled.
[ 32.542271] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:274
[ 32.550883] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
[ 32.558707] preempt_count: 1, expected: 0
[ 32.562710] RCU nest depth: 0, expected: 0
[ 32.566800] CPU: 3 PID: 1 Comm: swapper/0 Tainted: G W 6.2.0-rc2-00269-gae9dcb91c606 #7
[ 32.576188] Hardware name: Marvell CN106XX board (DT)
[ 32.581232] Call trace:
[ 32.583670] dump_backtrace.part.0+0xe0/0xf0
[ 32.587937] show_stack+0x18/0x30
[ 32.591245] dump_stack_lvl+0x68/0x84
[ 32.594900] dump_stack+0x18/0x34
[ 32.598206] __might_resched+0x12c/0x160
[ 32.602122] __might_sleep+0x48/0xa0
[ 32.605689] __kmem_cache_alloc_node+0x2b8/0x2e0
[ 32.610301] __kmalloc+0x58/0x190
[ 32.613610] otx2_sq_aura_pool_init+0x1a8/0x314
[ 32.618134] otx2_open+0x1d4/0x9d0
To avoid use of GFP_ATOMIC for memory allocation, disable preemption
after all memory allocation is done.
Fixes: 4af1b64f80fb ("octeontx2-pf: Fix lmtst ID used in aura free")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cong Wang says:
====================
l2tp: fix race conditions in l2tp_tunnel_register()
This patchset contains two patches, the first one is a preparation for
the second one which is the actual fix. Please find more details in
each patch description.
I have ran the l2tp test (https://github.com/katalix/l2tp-ktest),
all test cases are passed.
v3: preserve EEXIST errno for user-space
v2: move IDR allocation to l2tp_tunnel_register()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code in l2tp_tunnel_register() is racy in several ways:
1. It modifies the tunnel socket _after_ publishing it.
2. It calls setup_udp_tunnel_sock() on an existing socket without
locking.
3. It changes sock lock class on fly, which triggers many syzbot
reports.
This patch amends all of them by moving socket initialization code
before publishing and under sock lock. As suggested by Jakub, the
l2tp lockdep class is not necessary as we can just switch to
bh_lock_sock_nested().
Fixes: 37159ef2c1ae ("l2tp: fix a lockdep splat")
Fixes: 6b9f34239b00 ("l2tp: fix races in tunnel creation")
Reported-by: syzbot+52866e24647f9a23403f@syzkaller.appspotmail.com
Reported-by: syzbot+94cc2a66fc228b23f360@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Guillaume Nault <gnault@redhat.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Parkin <tparkin@katalix.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
l2tp uses l2tp_tunnel_list to track all registered tunnels and
to allocate tunnel ID's. IDR can do the same job.
More importantly, with IDR we can hold the ID before a successful
registration so that we don't need to worry about late error
handling, it is not easy to rollback socket changes.
This is a preparation for the following fix.
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Guillaume Nault <gnault@redhat.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Parkin <tparkin@katalix.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a nasty crash [1] in net_tx_action() which
made little sense until we got a repro.
This repro installs a taprio qdisc, but providing an
invalid TCA_RATE attribute.
qdisc_create() has to destroy the just initialized
taprio qdisc, and taprio_destroy() is called.
However, the hrtimer used by taprio had already fired,
therefore advance_sched() called __netif_schedule().
Then net_tx_action was trying to use a destroyed qdisc.
We can not undo the __netif_schedule(), so we must wait
until one cpu serviced the qdisc before we can proceed.
Many thanks to Alexander Potapenko for his help.
[1]
BUG: KMSAN: uninit-value in queued_spin_trylock include/asm-generic/qspinlock.h:94 [inline]
BUG: KMSAN: uninit-value in do_raw_spin_trylock include/linux/spinlock.h:191 [inline]
BUG: KMSAN: uninit-value in __raw_spin_trylock include/linux/spinlock_api_smp.h:89 [inline]
BUG: KMSAN: uninit-value in _raw_spin_trylock+0x92/0xa0 kernel/locking/spinlock.c:138
queued_spin_trylock include/asm-generic/qspinlock.h:94 [inline]
do_raw_spin_trylock include/linux/spinlock.h:191 [inline]
__raw_spin_trylock include/linux/spinlock_api_smp.h:89 [inline]
_raw_spin_trylock+0x92/0xa0 kernel/locking/spinlock.c:138
spin_trylock include/linux/spinlock.h:359 [inline]
qdisc_run_begin include/net/sch_generic.h:187 [inline]
qdisc_run+0xee/0x540 include/net/pkt_sched.h:125
net_tx_action+0x77c/0x9a0 net/core/dev.c:5086
__do_softirq+0x1cc/0x7fb kernel/softirq.c:571
run_ksoftirqd+0x2c/0x50 kernel/softirq.c:934
smpboot_thread_fn+0x554/0x9f0 kernel/smpboot.c:164
kthread+0x31b/0x430 kernel/kthread.c:376
ret_from_fork+0x1f/0x30
Uninit was created at:
slab_post_alloc_hook mm/slab.h:732 [inline]
slab_alloc_node mm/slub.c:3258 [inline]
__kmalloc_node_track_caller+0x814/0x1250 mm/slub.c:4970
kmalloc_reserve net/core/skbuff.c:358 [inline]
__alloc_skb+0x346/0xcf0 net/core/skbuff.c:430
alloc_skb include/linux/skbuff.h:1257 [inline]
nlmsg_new include/net/netlink.h:953 [inline]
netlink_ack+0x5f3/0x12b0 net/netlink/af_netlink.c:2436
netlink_rcv_skb+0x55d/0x6c0 net/netlink/af_netlink.c:2507
rtnetlink_rcv+0x30/0x40 net/core/rtnetlink.c:6108
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0xf3b/0x1270 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x1288/0x1440 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
____sys_sendmsg+0xabc/0xe90 net/socket.c:2482
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2536
__sys_sendmsg net/socket.c:2565 [inline]
__do_sys_sendmsg net/socket.c:2574 [inline]
__se_sys_sendmsg net/socket.c:2572 [inline]
__x64_sys_sendmsg+0x367/0x540 net/socket.c:2572
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
CPU: 0 PID: 13 Comm: ksoftirqd/0 Not tainted 6.0.0-rc2-syzkaller-47461-gac3859c02d7f #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/22/2022
Fixes: 5a781ccbd19e ("tc: Add support for configuring the taprio scheduler")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pable Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for net:
1) Increase timeout to 120 seconds for netfilter selftests to fix
nftables transaction tests, from Florian Westphal.
2) Fix overflow in bitmap_ip_create() due to integer arithmetics
in a 64-bit bitmask, from Gavrilov Ilia.
3) Fix incorrect arithmetics in nft_payload with double-tagged
vlan matching.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct queue statistics reading. All queue statistics are stored as unsigned
long values. The retrieval for ethtool fetches these values as u64. However, on
some systems the size of the counters are 32 bit. That yields wrong queue
statistic counters e.g., on arm32 systems such as the stm32mp157. Fix it by
using the correct data type.
Tested on Olimex STMP157-OLinuXino-LIME2 by simple running linuxptp for a short
period of time:
Non-patched kernel:
|root@st1:~# ethtool -S eth0 | grep q0
| q0_tx_pkt_n: 3775276254951 # ???
| q0_tx_irq_n: 879
| q0_rx_pkt_n: 1194000908909 # ???
| q0_rx_irq_n: 278
Patched kernel:
|root@st1:~# ethtool -S eth0 | grep q0
| q0_tx_pkt_n: 2434
| q0_tx_irq_n: 1274
| q0_rx_pkt_n: 1604
| q0_rx_irq_n: 846
Fixes: 68e9c5dee1cf ("net: stmmac: add ethtool per-queue statistic framework")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Cc: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reading pinconf-pins from debugfs it fails to get the configured pull
type on RK3568, "unsupported pinctrl type" error messages is also reported.
Fix this by adding support for RK3568 in rockchip_get_pull, including a
reverse of the pull-up value swap applied in rockchip_set_pull so that
pull-up is correctly reported in pinconf-pins.
Also update the workaround comment to reflect affected pins, GPIO0_D3-D6.
Fixes: c0dadc0e47a8 ("pinctrl: rockchip: add support for rk3568")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20230110172955.1258840-1-jonas@kwiboo.se
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since resplen and respoffs are signed integers sufficiently
large values of unsigned int len and offset members of RNDIS
response will result in negative values of prior variables.
This may be utilized to bypass implemented security checks
to either extract memory contents by manipulating offset or
overflow the data buffer via memcpy by manipulating both
offset and len.
Additionally assure that sum of resplen and respoffs does not
overflow so buffer boundaries are kept.
Fixes: 80f8c5b434f9 ("rndis_wlan: copy only useful data from rndis_command respond")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230111175031.7049-1-szymon.heidrich@gmail.com
|
|
A sanity check was introduced considering maximum flowrings above
256 as insane and effectively aborting the device probe. This
resulted in regression for number of users as the value turns out
to be sane after all.
Fixes: 2aca4f3734bd ("brcmfmac: return error when getting invalid max_flowrings from dongle")
Reported-by: chainofflowers <chainofflowers@posteo.net>
Link: https://lore.kernel.org/all/4781984.GXAFRqVoOG@luna/
Reported-by: Christian Marillat <marillat@debian.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216894
Cc: stable@vger.kernel.org
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230111112419.24185-1-arend.vanspriel@broadcom.com
|
|
When dealing with a device for 2GHz band only the wiphy->bands for
5GHz will be NULL. This would result in a NULL-deref in the
brcmf_cfg80211_dump_survey() function. Rework the code with a
for-loop to make it easier to add another band.
Fixes: 6c04deae1438 ("brcmfmac: Add dump_survey cfg80211 ops for HostApd AutoChannelSelection")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103124117.271988-3-arend.vanspriel@broadcom.com
|
|
An issue was reported in which periodically error messages are
printed in the kernel log:
[ 26.303445] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 26.303554] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,3-model-b-plus.bin failed with error -2
[ 26.516752] brcmfmac_wcc: brcmf_wcc_attach: executing
[ 26.528264] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Jan 4 2021 19:56:29 version 7.45.229 (617f1f5 CY) FWID 01-2dbd9d2e
[ 27.076829] Bluetooth: hci0: BCM: features 0x2f
[ 27.078592] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+
[ 27.078601] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0342
[ 30.142104] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SS
[ 30.590017] Bluetooth: MGMT ver 1.22
[ 104.897615] brcmfmac: cfg80211_set_channel: set chanspec 0x100e fail, reason -52
[ 104.897992] brcmfmac: cfg80211_set_channel: set chanspec 0xd022 fail, reason -52
[ 105.007672] brcmfmac: cfg80211_set_channel: set chanspec 0xd026 fail, reason -52
[ 105.117654] brcmfmac: cfg80211_set_channel: set chanspec 0xd02a fail, reason -52
[ 105.227636] brcmfmac: cfg80211_set_channel: set chanspec 0xd02e fail, reason -52
[ 106.987552] brcmfmac: cfg80211_set_channel: set chanspec 0xd090 fail, reason -52
[ 106.987911] brcmfmac: cfg80211_set_channel: set chanspec 0xd095 fail, reason -52
[ 106.988233] brcmfmac: cfg80211_set_channel: set chanspec 0xd099 fail, reason -52
[ 106.988565] brcmfmac: cfg80211_set_channel: set chanspec 0xd09d fail, reason -52
[ 106.988909] brcmfmac: cfg80211_set_channel: set chanspec 0xd0a1 fail, reason -52
This happens in brcmf_cfg80211_dump_survey() because we try a disabled
channel. When channel is marked as disabled we do not need to fill any
other info so bail out.
Fixes: 6c04deae1438 ("brcmfmac: Add dump_survey cfg80211 ops for HostApd AutoChannelSelection")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103124117.271988-2-arend.vanspriel@broadcom.com
|
|
Starting with GNU make 4.4, --jobserver-auth newly uses named
pipe (fifo) instead of part of opened file descriptors:
https://www.gnu.org/software/make/manual/html_node/POSIX-Jobserver.html
Support also the new format.
Signed-off-by: Martin Liska <mliska@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V DeviceTrees for v6.2
SiFive:
A solitary fix for the PCI memory regions on the unmatched, triggered by
an SM768. No-one must have tried one until just recently!
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-fixes-for-v6.2-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sifive: fu740: fix size of pcie 32bit memory
Link: https://lore.kernel.org/r/Y78rn+0fVNOxHLKt@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 6.2 (part 1)
Fix regression for gpio support on Armada 38x and Armada 38x
Fix address for UART1 on AC5/AC5X
* tag 'mvebu-fixes-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: AC5/AC5X: Fix address for UART1
Revert "ARM: dts: armada-39x: Fix compatible string for gpios"
Revert "ARM: dts: armada-38x: Fix compatible string for gpios"
Link: https://lore.kernel.org/r/87mt6mg08k.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Always configure GPIO pins which are used as interrupt source as INPUTs.
In case the default pin configuration is OUTPUT, or the prior stage does
configure the pins as OUTPUT, then Linux will not reconfigure the pin as
INPUT and no interrupts are received.
Always configure the interrupt source GPIO pin as input to fix the above case.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 07bd1a6cc7cbb ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
