| Age | Commit message (Collapse) | Author |
|---|
|
As comment in code specifies, SMM temporarily disables VMX so we cannot
be in guest mode, nor can VMLAUNCH/VMRESUME be pending.
However, code currently assumes that these are the only flags that can be
set on kvm_state->flags. This is not true as KVM_STATE_NESTED_EVMCS
can also be set on this field to signal that eVMCS should be enabled.
Therefore, fix code to check for guest-mode and pending VMLAUNCH/VMRESUME
explicitly.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This warning can be triggered easily by userspace, so it should certainly not
cause a panic if panic_on_warn is set.
Reported-by: syzbot+c03f30b4f4c46bdf8575@syzkaller.appspotmail.com
Suggested-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When compiling a kernel without support for CMA, CONFIG_CMA_ALIGNMENT
is not defined which results in the following build failure:
In file included from ./include/linux/list.h:9:0
from ./include/linux/kobject.h:19,
from ./include/linux/of.h:17
from ./include/linux/irqdomain.h:35,
from ./include/linux/acpi.h:13,
from drivers/iommu/arm-smmu-v3.c:12:
drivers/iommu/arm-smmu-v3.c: In function ‘arm_smmu_device_hw_probe’:
drivers/iommu/arm-smmu-v3.c:194:40: error: ‘CONFIG_CMA_ALIGNMENT’ undeclared (first use in this function)
#define Q_MAX_SZ_SHIFT (PAGE_SHIFT + CONFIG_CMA_ALIGNMENT)
Fix the breakage by capping the maximum queue size based on MAX_ORDER
when CMA is not enabled.
Reported-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Loud speaker pop happens during playback even when in slience
playback. Specify Max98357a amp delay times to make sure
clocks are always earlier than sdmode on.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The fixed regulator driver doesn't specify any con_id for gpio lookup
so it must be NULL in the table entry.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 1d272894ec4f ("ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
AP Queue Interruption Control (AQIC) facility gives
the guest the possibility to control interruption for
the Cryptographic Adjunct Processor queues.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
[ Modified while picking: we may not expose STFLE facility 65
unconditionally because AIV is a pre-requirement.]
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We register a AP PQAP instruction hook during the open
of the mediated device. And unregister it on release.
During the probe of the AP device, we allocate a vfio_ap_queue
structure to keep track of the information we need for the
PQAP/AQIC instruction interception.
In the AP PQAP instruction hook, if we receive a demand to
enable IRQs,
- we retrieve the vfio_ap_queue based on the APQN we receive
in REG1,
- we retrieve the page of the guest address, (NIB), from
register REG2
- we retrieve the mediated device to use the VFIO pinning
infrastructure to pin the page of the guest address,
- we retrieve the pointer to KVM to register the guest ISC
and retrieve the host ISC
- finaly we activate GISA
If we receive a demand to disable IRQs,
- we deactivate GISA
- unregister from the GIB
- unpin the NIB
When removing the AP device from the driver the device is
reseted and this process unregisters the GISA from the GIB,
and unpins the NIB address then we free the vfio_ap_queue
structure.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
To be able to use the VFIO interface to facilitate the
mediated device memory pinning/unpinning we need to register
a notifier for IOMMU.
While we will start to pin one guest page for the interrupt indicator
byte, this is still ok with ballooning as this page will never be
used by the guest virtio-balloon driver.
So the pinned page will never be freed. And even a broken guest does
so, that would not impact the host as the original page is still
in control by vfio.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We prepare the interception of the PQAP/AQIC instruction for
the case the AQIC facility is enabled in the guest.
First of all we do not want to change existing behavior when
intercepting AP instructions without the SIE allowing the guest
to use AP instructions.
In this patch we only handle the AQIC interception allowed by
facility 65 which will be enabled when the complete interception
infrastructure will be present.
We add a callback inside the KVM arch structure for s390 for
a VFIO driver to handle a specific response to the PQAP
instruction with the AQIC command and only this command.
But we want to be able to return a correct answer to the guest
even there is no VFIO AP driver in the kernel.
Therefor, we inject the correct exceptions from inside KVM for the
case the callback is not initialized, which happens when the vfio_ap
driver is not loaded.
We do consider the responsibility of the driver to always initialize
the PQAP callback if it defines queues by initializing the CRYCB for
a guest.
If the callback has been setup we call it.
If not we setup an answer considering that no queue is available
for the guest when no callback has been setup.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Kasan instrumentation of backchain unwinder stack reads is disabled
completely and simply uses READ_ONCE_NOCHECK now.
READ_ONCE_TASK_STACK macro is unused and could be removed.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Avoid kasan false positive when current task is interrupted in-between
stack frame allocation and backchain write instructions leaving new stack
frame backchain invalid. In particular if backchain is 0 the unwinder
tries to read pt_regs from the stack and might hit kasan poisoned bytes,
leading to kasan "stack-out-of-bounds" report.
Disable kasan instrumentation of unwinder stack reads, since this
limitation couldn't be handled otherwise with current backchain unwinder
implementation.
Fixes: 78c98f907413 ("s390/unwind: introduce stack unwind API")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Tested-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Current code sets the dsci to 0x00000080. Which doesn't make any sense,
as the indicator area is located in the _left-most_ byte.
Worse: if the dsci is the _shared_ indicator, this potentially clears
the indication of activity for a _different_ device.
tiqdio_thinint_handler() will then have no reason to call that device's
IRQ handler, and the device ends up stalling.
Fixes: d0c9d4a89fff ("[S390] qdio: set correct bit in dsci")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
When tiqdio_remove_input_queues() removes a queue from the tiq_list as
part of qdio_shutdown(), it doesn't re-initialize the queue's list entry
and the prev/next pointers go stale.
If a subsequent qdio_establish() fails while sending the ESTABLISH cmd,
it calls qdio_shutdown() again in QDIO_IRQ_STATE_ERR state and
tiqdio_remove_input_queues() will attempt to remove the queue entry a
second time. This dereferences the stale pointers, and bad things ensue.
Fix this by re-initializing the list entry after removing it from the
list.
For good practice also initialize the list entry when the queue is first
allocated, and remove the quirky checks that papered over this omission.
Note that prior to
commit e521813468f7 ("s390/qdio: fix access to uninitialized qdio_q fields"),
these checks were bogus anyway.
setup_queues_misc() clears the whole queue struct, and thus needs to
re-init the prev/next pointers as well.
Fixes: 779e6e1c724d ("[S390] qdio: new qdio driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The "len" variable is the length of the option up to the next option or
to the end of the string which ever first. We want to print the invalid
option so we want precision "%.*s" but the format is width "%*s" so it
prints up to the end of the string.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Sometimes, we want to control which of the matching drivers
binds to a subchannel device (e.g. for subchannels we want to
handle via vfio-ccw).
For pci devices, a mechanism to do so has been introduced in
782a985d7af2 ("PCI: Introduce new device binding path using
pci_dev.driver_override"). It makes sense to introduce the
driver_override attribute for subchannel devices as well, so
that we can easily extend the 'driverctl' tool (which makes
use of the driver_override attribute for pci).
Note that unlike pci we still require a driver override to
match the subchannel type; matching more than one subchannel
type is probably not useful anyway.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
When waking up from the Suspend-to-RAM state, the following error
was seen:
m25p80 spi2.0: flash operation timed out
The flash remained in an undefined state, returning 0xFFs.
Fix it by setting the Serial Clock Baud Rate, as it was set
before the conversion to SPIMEM.
Tested with sama5d2_xplained and mx25l25673g spi-nor in
Backup + Self-Refresh and Suspend modes.
Fixes: 0e6aae08e9ae ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Reported-by: Mark Deneen <mdeneen@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have devm_xxx version of snd_soc_register_component,
let's use it.
This patch also removes related empty functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have devm_xxx version of snd_soc_register_component,
let's use it.
This patch also removes related empty functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Despite what I think the prm recommends, commit f2253bd9859b
("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context") turned out
to be a huge mistake when enabling Ironlake contexts as the GPU would
hang on either a MI_FLUSH or PIPE_CONTROL immediately following the
MI_SET_CONTEXT of an active mesa context (more vanilla contexts, e.g.
simple rendercopies with igt, do not suffer).
Ville found the following clue,
"[DevCTG+]: For the invalidate operation of the pipe control, the
following pointers are affected. The
invalidate operation affects the restore of these packets. If the pipe
control invalidate operation is completed
before the context save, the indirect pointers will not be restored from
memory.
1. Pipeline State Pointer
2. Media State Pointer
3. Constant Buffer Packet"
which suggests by us emitting the INVALIDATE prior to the MI_SET_CONTEXT,
we prevent the context-restore from chasing the dangling pointers within
the image, and explains why this likely prevents the GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419111749.3910-1-chris@chris-wilson.co.uk
(cherry picked from commit 928f8f42310f244501a7c70daac82c196112c190 in drm-intel-next)
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111014
Fixes: f2253bd9859b ("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
commit 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
removed the error path from atmel_qspi_init(), but not changed the
function's return type. Set void return type for atmel_qspi_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is possible to request a transfer with a speed lower than supported
by the HW. This causes silent divider calculation underflow in
ssp_get_clk_div() which leads to a frequency higher than requested. Up to
maximum speed of the controller.
Set the minimum supported transfer speed and let the SPI core to
validate no transfers have speed lower than supported.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
It's controlled by using system configuration registers (SYSCFG).
Introduce two compatibles as the booster regulator is controlled by:
- a unique register/bit in STM32H7
- a set/clear register pair in STM32MP1
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
This regulator is supplied by vdda. It's controlled by using SYSCFG:
- STM32H7 has a unique register to set/clear the booster enable bit
- STM32MP1 has separate set and clear registers to configure it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
paranoid_exit needs to restore CR3 before GSBASE. Doing it in the opposite
order crashes if the exception came from a context with user GSBASE and
user CR3 -- RESTORE_CR3 cannot resture user CR3 if run with user GSBASE.
This results in infinitely recursing exceptions if user code does SYSENTER
with TF set if both FSGSBASE and PTI are enabled.
The old code worked if user code just set TF without SYSENTER because #DB
from user mode is special cased in idtentry and paranoid_exit doesn't run.
Fix it by cleaning up the spaghetti code. All that paranoid_exit needs to
do is to disable IRQs, handle IRQ tracing, then restore CR3, and restore
GSBASE. Simply do those actions in that order.
Fixes: 708078f65721 ("x86/entry/64: Handle FSGSBASE enabled paranoid entry/exit")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: https://lkml.kernel.org/r/59725ceb08977359489fbed979716949ad45f616.1562035429.git.luto@kernel.org
|
|
It's only used if !CONFIG_IA32_EMULATION, so disable it in normal
configs. This will save a few bytes of text and reduce confusion.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "BaeChang Seok" <chang.seok.bae@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Bae, Chang Seok" <chang.seok.bae@intel.com>
Link: https://lkml.kernel.org/r/0f7dafa72fe7194689de5ee8cfe5d83509fabcf5.1562035429.git.luto@kernel.org
|
|
Make sure that both variants of the nasty TF-in-compat-syscall are
exercised regardless of what vendor's CPU is running the tests.
Also change the intentional signal after SYSCALL to use ud2, which
is a lot more comprehensible.
This crashes the kernel due to an FSGSBASE bug right now.
This test *also* detects a bug in KVM when run on an Intel host. KVM
people, feel free to use it to help debug. There's a bunch of code in this
test to warn instead of going into an infinite looping when the bug gets
triggered.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "BaeChang Seok" <chang.seok.bae@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Cc: "Bae, Chang Seok" <chang.seok.bae@intel.com>
Link: https://lkml.kernel.org/r/5f5de10441ab2e3005538b4c33be9b1965d1bb63.1562035429.git.luto@kernel.org
|
|
Fix sparse warnings:
lib/reed_solomon/test_rslib.c:313:5: warning: symbol 'ex_rs_helper' was not declared. Should it be static?
lib/reed_solomon/test_rslib.c:349:5: warning: symbol 'exercise_rs' was not declared. Should it be static?
lib/reed_solomon/test_rslib.c:407:5: warning: symbol 'exercise_rs_bc' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <ferdinand.blomqvist@gmail.com>
Link: https://lkml.kernel.org/r/20190702061847.26060-1-yuehaibing@huawei.com
|
|
The irqchip driver depends on the SoC specific driver, but we want
to be able to compile-test it elsewhere:
WARNING: unmet direct dependencies detected for TI_SCI_INTA_MSI_DOMAIN
Depends on [n]: SOC_TI [=n]
Selected by [y]:
- TI_SCI_INTA_IRQCHIP [=y] && TI_SCI_PROTOCOL [=y]
drivers/irqchip/irq-ti-sci-inta.o: In function `ti_sci_inta_irq_domain_probe':
irq-ti-sci-inta.c:(.text+0x204): undefined reference to `ti_sci_inta_msi_create_irq_domain'
Rearrange the Kconfig and Makefile so we build the soc driver whenever
its users are there, regardless of the SOC_TI option.
Fixes: 49b323157bf1 ("soc: ti: Add MSI domain bus support for Interrupt Aggregator")
Fixes: f011df6179bd ("irqchip/ti-sci-inta: Add msi domain support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
arm/fixes
mvebu fixes for 5.2 (part 2)
Use the armada-38x-uart compatible strings for Armada XP 98dx3236 SoCs
in order to not loose character anymore.
* tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The userspace tools expect all fields of the same name to be logged
consistently with the same encoding. Since the invalid_context fields
contain untrusted strings in selinux_inode_setxattr()
and selinux_setprocattr(), encode all instances of this field the same
way as though they were untrusted even though
compute_sid_handle_invalid_context() and security_sid_mls_copy() are
trusted.
Please see github issue
https://github.com/linux-audit/audit-kernel/issues/57
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
The widget_mutex was introduced to serialize callers to
hda_widget_sysfs_{re}init. However, its protection of the sysfs widget array
is incomplete. For example, it is acquired around the call to
hda_widget_sysfs_reinit(), which actually creates the new array, but isn't
still acquired when codec->num_nodes and codec->start_nid is updated. So
the lock ensures one thread sets up the new array at a time, but doesn't
ensure which thread's value will end up in codec->num_nodes. If a larger
num_nodes wins but a smaller array was set up, the next call to
refresh_widgets() will touch free memory as it iterates over codec->num_nodes
that aren't there.
The widget_lock really protects both the tree as well as codec->num_nodes,
start_nid, and end_nid, so make sure it's held across that update. It should
also be held during snd_hdac_get_sub_nodes(), so that a very old read from that
function doesn't end up clobbering a later update.
Fixes: ed180abba7f1 ("ALSA: hda: Fix race between creating and refreshing sysfs entries")
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
cmpxchg() with an immediate value could be replaced with less expensive
xchg(). The same true if new value don't _depend_ on the old one.
In the second block, atomic_cmpxchg() return value isn't checked, so
after atomic_cmpxchg() -> atomic_xchg() conversion it could be replaced
with atomic_set(). Comparison with atomic_read() in the second chunk was
left as an optimisation (if that was the initial intention).
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Recommended by the hw team.
Reviewed-and-Tested-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This back-merge is necessary for adjusting the latest FireWire fix
with the recent refactoring in 5.3 development branch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In IEC 61883-6, 8 MIDI data streams are multiplexed into single
MIDI conformant data channel. The index of stream is calculated by
modulo 8 of the value of data block counter.
In fireworks, the value of data block counter in CIP header has a quirk
with firmware version v5.0.0, v5.7.3 and v5.8.0. This brings ALSA
IEC 61883-1/6 packet streaming engine to miss detection of MIDI
messages.
This commit fixes the miss detection to modify the value of data block
counter for the modulo calculation.
For maintainers, this bug exists since a commit 18f5ed365d3f ("ALSA:
fireworks/firewire-lib: add support for recent firmware quirk") in Linux
kernel v4.2. There're many changes since the commit. This fix can be
backported to Linux kernel v4.4 or later. I tagged a base commit to the
backport for your convenience.
Besides, my work for Linux kernel v5.3 brings heavy code refactoring and
some structure members are renamed in 'sound/firewire/amdtp-stream.h'.
The content of this patch brings conflict when merging -rc tree with
this patch and the latest tree. I request maintainers to solve the
conflict to replace 'tx_first_dbc' with 'ctx_data.tx.first_dbc'.
Fixes: df075feefbd3 ("ALSA: firewire-lib: complete AM824 data block processing layer")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux
* 'for-next/perf' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
MAINTAINERS: Add maintainer entry for the imx8 DDR PMU driver
drivers/perf: imx_ddr: Add DDR performance counter support to perf
dt-bindings: perf: imx8-ddr: add imx8qxp ddr performance monitor
|
|
sys_move_mount() crashes by dereferencing the pointer MNT_NS_INTERNAL,
a.k.a. ERR_PTR(-EINVAL), if the old mount is specified by fd for a
kernel object with an internal mount, such as a pipe or memfd.
Fix it by checking for this case and returning -EINVAL.
[AV: what we want is is_mounted(); use that instead of making the
condition even more convoluted]
Reproducer:
#include <unistd.h>
#define __NR_move_mount 429
#define MOVE_MOUNT_F_EMPTY_PATH 0x00000004
int main()
{
int fds[2];
pipe(fds);
syscall(__NR_move_mount, fds[0], "", -1, "/", MOVE_MOUNT_F_EMPTY_PATH);
}
Reported-by: syzbot+6004acbaa1893ad013f0@syzkaller.appspotmail.com
Fixes: 2db154b3ea8e ("vfs: syscall: Add move_mount(2) to move mounts around")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Make sure to return a proper negative error code from copy_process()
when anon_inode_getfile() fails with CLONE_PIDFD.
Otherwise _do_fork() will not detect an error and get_task_pid() will
operator on a nonsensical pointer:
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006dbc2c
R13: 00007ffc15fbb0ff R14: 00007ff07e47e9c0 R15: 0000000000000000
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 7990 Comm: syz-executor290 Not tainted 5.2.0-rc6+ #9
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:194 [inline]
RIP: 0010:get_task_pid+0xe1/0x210 kernel/pid.c:372
Code: 89 ff e8 62 27 5f 00 49 8b 07 44 89 f1 4c 8d bc c8 90 01 00 00 eb 0c
e8 0d fe 25 00 49 81 c7 38 05 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 18 00 74
08 4c 89 ff e8 31 27 5f 00 4d 8b 37 e8 f9 47 12 00
RSP: 0018:ffff88808a4a7d78 EFLAGS: 00010203
RAX: 00000000000000a7 RBX: dffffc0000000000 RCX: ffff888088180600
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88808a4a7d90 R08: ffffffff814fb3a8 R09: ffffed1015d66bf8
R10: ffffed1015d66bf8 R11: 1ffff11015d66bf7 R12: 0000000000041ffc
R13: 1ffff11011494fbc R14: 0000000000000000 R15: 000000000000053d
FS: 00007ff07e47e700(0000) GS:ffff8880aeb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004b5100 CR3: 0000000094df2000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
_do_fork+0x1b9/0x5f0 kernel/fork.c:2360
__do_sys_clone kernel/fork.c:2454 [inline]
__se_sys_clone kernel/fork.c:2448 [inline]
__x64_sys_clone+0xc1/0xd0 kernel/fork.c:2448
do_syscall_64+0xfe/0x140 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Link: https://lore.kernel.org/lkml/000000000000e0dc0d058c9e7142@google.com
Reported-and-tested-by: syzbot+002e636502bc4b64eb5c@syzkaller.appspotmail.com
Fixes: 6fd2fe494b17 ("copy_process(): don't use ksys_close() on cleanups")
Cc: Jann Horn <jannh@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christian Brauner <christian@brauner.io>
|
|
To save power, the hda hdmi driver in ASoC invokes snd_hdac_ext_bus_link_put
to disable CORB/RIRB buffers DMA if there is no user of bus and invokes
snd_hdac_ext_bus_link_get to set up CORB/RIRB buffers when it is used.
Unsolicited responses is disabled in snd_hdac_bus_stop_cmd_io called by
snd_hdac_ext_bus_link_put , but it is not enabled in snd_hdac_bus_init_cmd_io
called by snd_hdac_ext_bus_link_get. So for put-get sequence, Unsolicited
responses is disabled and headphone can't be detected by hda codecs.
Now unsolicited responses is only enabled in snd_hdac_bus_reset_link
which resets controller. The function is only called for setup of
controller. This patch enables Unsolicited responses after RIRB is
initialized in snd_hdac_bus_init_cmd_io which works together with
snd_hdac_bus_reset_link to set up controller.
Tested legacy hda driver and SOF driver on intel whiskeylake.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
'bio->bi_iter.bi_size' is 'unsigned int', which at most hold 4G - 1
bytes.
Before 07173c3ec276 ("block: enable multipage bvecs"), one bio can
include very limited pages, and usually at most 256, so the fs bio
size won't be bigger than 1M bytes most of times.
Since we support multi-page bvec, in theory one fs bio really can
be added > 1M pages, especially in case of hugepage, or big writeback
with too many dirty pages. Then there is chance in which .bi_size
is overflowed.
Fixes this issue by using bio_full() to check if the added segment may
overflow .bi_size.
Cc: Liu Yiding <liuyd.fnst@cn.fujitsu.com>
Cc: kernel test robot <rong.a.chen@intel.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: linux-xfs@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 07173c3ec276 ("block: enable multipage bvecs")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
