| Age | Commit message (Collapse) | Author |
|---|
|
At least one older CH341 appears to have the RX timer enable bit
inverted so that setting it disables the RX timer and prevents the FIFO
from emptying until it is full.
Only set the RX timer enable bit for devices with version newer than
0x27 (even though this probably affects all pre-0x30 devices).
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Tested-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au
Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on reconfiguration")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Disable LCR updates for pre-0x30 devices which use a different (unknown)
protocol for line control and where the current register write causes
the next received character to be lost.
Note that updating LCR using the INIT command has no effect on these
devices either.
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Tested-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au
Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on reconfiguration")
Fixes: 55fa15b5987d ("USB: serial: ch341: fix baud rate and line-control handling")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
As reported by Zhouyi Zhou, WRITE_ONCE() is not atomic
as expected when KASAN or KCSAN are compiled in.
Fix it by re-implementing it using inline assembly.
Fixes: 077fc62b2b66 ("powerpc/irq: remove inline assembly in hard_irq_disable macro")
Reported-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a8298991b3df049a54ee8e558838e34265812014.1661272586.git.christophe.leroy@csgroup.eu
|
|
The function neigh_timer_handler() is a timer handler that runs in an
atomic context. When used by rocker, neigh_timer_handler() calls
"kzalloc(.., GFP_KERNEL)" that may sleep. As a result, the sleep in
atomic context bug will happen. One of the processes is shown below:
ofdpa_fib4_add()
...
neigh_add_timer()
(wait a timer)
neigh_timer_handler()
neigh_release()
neigh_destroy()
rocker_port_neigh_destroy()
rocker_world_port_neigh_destroy()
ofdpa_port_neigh_destroy()
ofdpa_port_ipv4_neigh()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: 00fc0c51e35b ("rocker: Change world_ops API and implementation to be switchdev independant")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the device id for Decagon Devices USB Cable Adapter.
Link: https://lore.kernel.org/r/trinity-819f9db2-d3e1-40e9-a669-9c245817c046-1661523546680@msvc-mesg-web108
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Previous behavior is to segfault if there is no CPU PMU table and a
metric is sought. To reproduce compile with NO_JEVENTS=1 then request a
metric, for example, "perf stat -M IPC true".
Committer testing:
Before:
$ make -k NO_JEVENTS=1 BUILD_BPF_SKEL=1 O=/tmp/build/perf-urgent -C tools/perf install-bin
$ perf stat -M IPC true
Segmentation fault (core dumped)
$
After:
$ perf stat -M IPC true
Usage: perf stat [<options>] [<command>]
-M, --metrics <metric/metric group list>
monitor specified metrics or metric groups (separated by ,)
$
Fixes: 00facc760903be66 ("perf jevents: Switch build to use jevents.py")
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Caleb Biggers <caleb.biggers@intel.com>
Cc: Florian Fischer <florian.fischer@muhq.space>
Cc: Ian Rogers <rogers.email@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Kshipra Bopardikar <kshipra.bopardikar@intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Perry Taylor <perry.taylor@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Link: https://lore.kernel.org/r/20220830164846.401143-3-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
After running the nolibc tests, the "git status" is not clean because
the generated files are not ignored. Create a `.gitignore` inside the
selftests/nolibc directory to ignore them.
Cc: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Cc: Fernanda Ma'rouf <fernandafmr2@gmail.com>
Signed-off-by: Fernanda Ma'rouf <fernandafmr12@gnuweeb.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
It presents the supported targets, and becomes the default target to
save the user from having to read the makefile. The "all" target was
placed after it and now points to "run" to do everything since it's
no longer the default one.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
It's not convenient to rely on a sysroot built in another directory,
especially when running cross-compilation tests, where one has to
switch back and forth between directories.
Let's make it possible to install the sysroot directly in the test
directory. It's not big and even benefits from being copied by arch
so that it's easier to switch between archs if needed. The new
"sysroot" target does this, it just calls "headers_standalone" from
nolibc to install the sysroot right here.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The "run" target will build the kernel and start it in QEMU. The
"rerun" target will not have the kernel dependency and will just try
to start QEMU. The QEMU architecture used to start the kernel is
derived from the configured ARCH. This might need to be improved
for archs which include different variants under the same name
(mips vs mipsel, +/-64, riscv32 vs riscv64). This could be tested
for i386, x86, arm, arm64, mips and riscv (the later two reporting
issues on some tests).
It is possible to pass a test specification for nolibc-test in the TEST
variable, which will be passed as-is as NOLIBC_TEST.
On success, the number of successful tests is printed. On failure, failed
lines are individually printed.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
While most archs will work fine with "make defconfig", not all will
do, and it's not always easy to remember the most suitable choice to
use for a specific architecture.
This adds a "defconfig" target to the Makefile so that one may easily
run "make -C ... defconfig" and make sure to clean and rebuild a fresh
config. This is *not* used by default because we want to preserve the
user's config by default.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The "kernel" target rebuilds the kernel with the current config for the
selected arch, with an initramfs containing the nolibc-test utility.
Since image names depend on the architecture, the currently supported
ones are referenced and resolved based on the architecture.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
Adding support for glibc can be useful to distinguish between bugs in
nolibc and bugs in the kernel when a syscall reports an unusual value.
It's not that much work and should not affect the long term
maintainability of the tests. The necessary changes can essentially be
summed up like this:
- set _GNU_SOURCE a the top to access some definitions
- many includes added when we know we don't come from nolibc (missing
the stdio include guard)
- disable gettid() which is not exposed by glibc
- disable gettimeofday's support of bad pointers since these crash
in glibc
- add a simple itoa() for errorname(); strerror() is too verbose (no
way to get short messages). strerrorname_np() was added in modern
glibc (2.32) to do exactly this but that 's too recent to be usable
as the default fallback.
- use the standard ioperm() definition. May be we need to implement
ioperm() in nolibc if that's useful.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
If /proc is not available (program run inside a chroot or without
sufficient permissions), it's better to disable the associated tests.
Some will be preserved like the ones which check for a failure to
create some entries there since they're still supposed to fail.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
Most of the time the program will be run alone in an initramfs. There
is no value in requiring the user to populate /dev and /proc for such
tests, we can do it ourselves, and it participates to the tests at the
same time.
What's done here is that when called as init (getpid()==1) we check
if /dev exists or create it, if /dev/console and /dev/null exists,
otherwise we try to mount a devtmpfs there, and if it fails we fall
back to mknod. The console is reopened if stdout was closed. Finally
/proc is created and mounted if /proc/self cannot be found. This is
sufficient for most tests.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
QEMU, when started with "-device isa-debug-exit -no-reboot" will exit
with status code 2N+1 when N is written to 0x501. This is particularly
convenient for automated tests but this is not portable. As such we
only enable this on x86_64 when pid==1. In addition, this requires an
ioperm() call but in order not to have to define arch-specific syscalls
we just perform the syscall by hand there.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The idea is to ease automated testing under qemu. If the test succeeds
while running as PID 1, indicating the system was booted with init=/test,
let's just power off so that qemu can exit with a successful code. In
other situations it will exit and provoke a panic, which may be caught
for example with CONFIG_PVPANIC.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The test series called "stdlib" covers some libc functions (string,
stdlib etc). By default they are automatically run after "syscall"
but may be requested in argument or in variable NOLIBC_TEST.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
This adds 63 tests covering about 34 syscalls. Both successes and
failures are tested. Two tests fail when run as unprivileged user
(link_dir which returns EACCESS instead of EPERM, and chroot which
returns EPERM). One test (execve("/")) expects to fail on EACCESS,
but needs to have valid arguments otherwise the kernel will log a
message. And a few tests require /proc to be mounted.
The code is not pretty since all tests are one-liners, sometimes
resulting in long lines, especially when using compount statements to
preset a line, but it's convenient and doesn't obfuscate the code,
which is important to understand what failed.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
It now becomes possible to pass a string either in argv[1] or in the
NOLIBC_TEST environment variable (the former having precedence), to
specify which tests to run. The format is:
testname[:range]*[,testname...]
Where a range is either a single value or the min and max numbers of the
test IDs in a sequence, delimited by a dash. Multiple ranges are possible.
This should provide enough flexibility to focus on certain failing parts
just by playing with the boot command line in a boot loader or in qemu
depending on what is accessible.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
This creates a "nolibc" selftest that intends to test various parts of
the nolibc component, both in terms of build and execution for a given
architecture.
The aim is for it to be as simple to run as a kernel build, by just
passing the compiler (for the build) and the ARCH (for kernel and
execution).
It brings a basic squeleton made of a single C file that will ease testing
and error reporting. The code will be arranged so that it remains easy to
add basic tests for syscalls or library calls that may rely on a condition
to be executed, and whose result is compared to a value or to an error
with a specific errno value.
Tests will just use a relative line number in switch/case statements as
an index, saving the user from having to maintain arrays and complicated
functions which can often just be one-liners.
MAINTAINERS was updated.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
__NR_mmap2 was used for i386 but it's also needed for other archs such
as RISCV32 or ARM. Let's decide to use it based on the __NR_mmap2
definition as it's not defined on other archs.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
We return -ENOSYS when there's no syscall6() operation, but we must cast
it to void* to avoid a warning.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The "ld a0, 0(sp)" instruction doesn't build on RISCV32 because that
would load a 64-bit value into a 32-bit register. But argc 32-bit,
not 64, so we ought to use "lw" here. Tested on both RISCV32 and
RISCV64.
Cc: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
As discussed, clarify LKMM not recognizing certain kinds of orderings.
In particular, highlight the fact that LKMM might deliberately make
weaker guarantees than compilers and architectures.
[ paulmck: Fix whitespace issue noted by checkpatch.pl. ]
Link: https://lore.kernel.org/all/YpoW1deb%2FQeeszO1@ethstick13.dse.in.tum.de/T/#u
Co-developed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Heidekrüger <paul.heidekrueger@in.tum.de>
Reviewed-by: Marco Elver <elver@google.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: Charalampos Mainas <charalampos.mainas@gmail.com>
Cc: Pramod Bhatotia <pramod.bhatotia@in.tum.de>
Cc: Soham Chakraborty <s.s.chakraborty@tudelft.nl>
Cc: Martin Fink <martin.fink@in.tum.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
Substitution of "data dependency barrier" with "address-dependency
barrier" left quite a lot of lines exceeding 80 columns.
Reflow those lines as well as a few short ones not related to
the substitution.
No changes in documentation text.
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Will Deacon <will@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Daniel Lustig <dlustig@nvidia.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The term "data dependency barrier", which has been in
memory-barriers.txt ever since it was first authored by David Howells,
has become confusing due to the fact that in LKMM's explanations.txt
and elsewhere, "data dependency" is used mostly for load-to-store data
dependency.
To prevent further confusions, do the changes listed below:
- substitute "data dependency barrier" with "address-dependency
barrier";
- add note on the removal of kernel APIs for explicit address-
dependency barriers in kernel release v5.9;
- note that address-dependency barriers are not necessary for
load-to-store situations;
- use READ_ONCE_OLD() for pre-4.15 READ_ONCE() (no implicit address-
dependency barrier);
- fix count of kernel memory barrier APIs;
- and a few more context adjustments.
Note: Cleanups of long lines are deferred to a followup patch.
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Link: https://lore.kernel.org/r/20211011064233-mutt-send-email-mst@kernel.org/
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Will Deacon <will@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Daniel Lustig <dlustig@nvidia.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The regcache sync will set the cache_bypass = true, at that
time, when there is regmap write operation, it will bypass
the regmap cache, then the regcache sync will write back the
value from cache to register, which is not as our expectation.
Though regmap already use its internal lock to avoid such issue,
but this driver force disable the regmap internal lock in its
regmap config: disable_locking = true
To avoid this issue, use the driver's own lock to do the protect
in system PM.
Fixes: b76574300504 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
splice back the hook list so nft_chain_release_hook() has a chance to
release the hooks.
BUG: memory leak
unreferenced object 0xffff88810180b100 (size 96):
comm "syz-executor133", pid 3619, jiffies 4294945714 (age 12.690s)
hex dump (first 32 bytes):
28 64 23 02 81 88 ff ff 28 64 23 02 81 88 ff ff (d#.....(d#.....
90 a8 aa 83 ff ff ff ff 00 00 b5 0f 81 88 ff ff ................
backtrace:
[<ffffffff83a8c59b>] kmalloc include/linux/slab.h:600 [inline]
[<ffffffff83a8c59b>] nft_netdev_hook_alloc+0x3b/0xc0 net/netfilter/nf_tables_api.c:1901
[<ffffffff83a9239a>] nft_chain_parse_netdev net/netfilter/nf_tables_api.c:1998 [inline]
[<ffffffff83a9239a>] nft_chain_parse_hook+0x33a/0x530 net/netfilter/nf_tables_api.c:2073
[<ffffffff83a9b14b>] nf_tables_addchain.constprop.0+0x10b/0x950 net/netfilter/nf_tables_api.c:2218
[<ffffffff83a9c41b>] nf_tables_newchain+0xa8b/0xc60 net/netfilter/nf_tables_api.c:2593
[<ffffffff83a3d6a6>] nfnetlink_rcv_batch+0xa46/0xd20 net/netfilter/nfnetlink.c:517
[<ffffffff83a3db79>] nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:638 [inline]
[<ffffffff83a3db79>] nfnetlink_rcv+0x1f9/0x220 net/netfilter/nfnetlink.c:656
[<ffffffff83a13b17>] netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
[<ffffffff83a13b17>] netlink_unicast+0x397/0x4c0 net/netlink/af_netlink.c:1345
[<ffffffff83a13fd6>] netlink_sendmsg+0x396/0x710 net/netlink/af_netlink.c:1921
[<ffffffff83865ab6>] sock_sendmsg_nosec net/socket.c:714 [inline]
[<ffffffff83865ab6>] sock_sendmsg+0x56/0x80 net/socket.c:734
[<ffffffff8386601c>] ____sys_sendmsg+0x36c/0x390 net/socket.c:2482
[<ffffffff8386a918>] ___sys_sendmsg+0xa8/0x110 net/socket.c:2536
[<ffffffff8386aaa8>] __sys_sendmsg+0x88/0x100 net/socket.c:2565
[<ffffffff845e5955>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff845e5955>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
[<ffffffff84800087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: d54725cd11a5 ("netfilter: nf_tables: support for multiple devices per netdev hook")
Reported-by: syzbot+5fcdbfab6d6744c57418@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The DT validator reports an error in the schema:
Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml: ignoring, error in schema: patternProperties: ^(5vs[1-2]|(l|s)[1-9][0-9]?|lvs[1-3])$: properties
Move the unevaluatedProperties statement out of the properties section
to fix it.
Fixes: 0b3bbd7646b0 ("regulator: qcom,spmi-regulator: Convert to dtschema")
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20220831080503.17600-1-jean-philippe@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The IPv6 path already drops dst in the daddr changed case, but the IPv4
path does not. This change makes the two code paths consistent.
Further, it is possible that there is already a metadata_dst allocated from
ingress that might already be attached to skbuff->dst while following
the bridge path. If it is not released before setting a new
metadata_dst, it will be leaked. This is similar to what is done in
bpf_set_tunnel_key() or ip6_route_input().
It is important to note that the memory being leaked is not the dst
being set in the bridge code, but rather memory allocated from some
other code path that is not being freed correctly before the skb dst is
overwritten.
An example of the leakage fixed by this commit found using kmemleak:
unreferenced object 0xffff888010112b00 (size 256):
comm "softirq", pid 0, jiffies 4294762496 (age 32.012s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 80 16 f1 83 ff ff ff ff ................
e1 4e f6 82 ff ff ff ff 00 00 00 00 00 00 00 00 .N..............
backtrace:
[<00000000d79567ea>] metadata_dst_alloc+0x1b/0xe0
[<00000000be113e13>] udp_tun_rx_dst+0x174/0x1f0
[<00000000a36848f4>] geneve_udp_encap_recv+0x350/0x7b0
[<00000000d4afb476>] udp_queue_rcv_one_skb+0x380/0x560
[<00000000ac064aea>] udp_unicast_rcv_skb+0x75/0x90
[<000000009a8ee8c5>] ip_protocol_deliver_rcu+0xd8/0x230
[<00000000ef4980bb>] ip_local_deliver_finish+0x7a/0xa0
[<00000000d7533c8c>] __netif_receive_skb_one_core+0x89/0xa0
[<00000000a879497d>] process_backlog+0x93/0x190
[<00000000e41ade9f>] __napi_poll+0x28/0x170
[<00000000b4c0906b>] net_rx_action+0x14f/0x2a0
[<00000000b20dd5d4>] __do_softirq+0xf4/0x305
[<000000003a7d7e15>] __irq_exit_rcu+0xc3/0x140
[<00000000968d39a2>] sysvec_apic_timer_interrupt+0x9e/0xc0
[<000000009e920794>] asm_sysvec_apic_timer_interrupt+0x16/0x20
[<000000008942add0>] native_safe_halt+0x13/0x20
Florian Westphal says: "Original code was likely fine because nothing
ever did set a skb->dst entry earlier than bridge in those days."
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Harsh Modi <harshmodi@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
__nf_ct_try_assign_helper() remains in place but it now requires a
template to configure the helper.
A toggle to disable automatic helper assignment was added by:
a9006892643a ("netfilter: nf_ct_helper: allow to disable automatic helper assignment")
in 2012 to address the issues described in "Secure use of iptables and
connection tracking helpers". Automatic conntrack helper assignment was
disabled by:
3bb398d925ec ("netfilter: nf_ct_helper: disable automatic helper assignment")
back in 2016.
This patch removes the sysctl and modparam toggles, users now have to
rely on explicit conntrack helper configuration via ruleset.
Update tools/testing/selftests/netfilter/nft_conntrack_helper.sh to
check that auto-assignment does not happen anymore.
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This reverts commit 3d5f70949f1b1168fbb17d06eb5c57e984c56c58.
The quirk does not work properly, more work is needed to determine what
should be done here.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Fixes: 3d5f70949f1b ("usb: add quirks for Lenovo OneLink+ Dock")
Link: https://lore.kernel.org/r/9a17ea86-079f-510d-e919-01bc53a6d09f@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Quanta 0408:4034 camera implements UVC 1.5, and thus sets
bInterfaceProtocol to UVC_PC_PROTOCOL_15. Commit 95f03d973478 ("media:
uvcvideo: Limit power line control for Quanta cameras") added a quirk
for the device that incorrectly specified the UVC 1.0 protocol,
rendering the quirk inoperative. Fix it.
Link: https://lore.kernel.org/linux-media/20220822131754.102393-1-ribalda@chromium.org
Fixes: 95f03d973478 ("media: uvcvideo: Limit power line control for Quanta cameras")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
VDD_OTHER is not connected to any on board consumer thus it is not
needed to keep it enabled all the time.
Fixes: 68a95ef72cef ("ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-9-claudiu.beznea@microchip.com
|
|
ldo2 is not used by any consumer on sama5d27_wlsom1 board, thus
don't keep it enabled all the time.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-8-claudiu.beznea@microchip.com
|
|
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-7-claudiu.beznea@microchip.com
|
|
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 68a95ef72cef ("ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-6-claudiu.beznea@microchip.com
|
|
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-5-claudiu.beznea@microchip.com
|
|
On SAMA7G5, when resuming from backup and self-refresh, the bootloader
performs DDR PHY recalibration by restoring the value of ZQ0SR0 (stored
in RAM by Linux before going to backup and self-refresh). It has been
discovered that the current procedure doesn't work for all possible values
that might go to ZQ0SR0 due to hardware bug. The workaround to this is to
avoid storing some values in ZQ0SR0. Thus Linux will read the ZQ0SR0
register and cache its value in RAM after processing it (using
modified_gray_code array). The bootloader will restore the processed value.
Fixes: d2d4716d8384 ("ARM: at91: pm: save ddr phy calibration data to securam")
Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-4-claudiu.beznea@microchip.com
|
|
It has been discovered that on some parts, from time to time, self-refresh
procedure doesn't work as expected. Debugging and investigating it proved
that disabling AC DLL introduce glitches in RAM controllers which
leads to unexpected behavior. This is confirmed as a hardware bug. DLL
bypass disables 3 DLLs: 2 DX DLLs and AC DLL. Thus, keep only DX DLLs
disabled. This introduce 6mA extra current consumption on VDDCORE when
switching to any ULP mode or standby mode but the self-refresh procedure
still works.
Fixes: f0bbf17958e8 ("ARM: at91: pm: add self-refresh support for sama7g5")
Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-3-claudiu.beznea@microchip.com
|
|
Don't just print a warning. Clean up and return an error as well.
Fixes: c8349639324a ("net: lan966x: Add FDMA functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/YwjgDm/SVd5c1tQU@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running `ethtool -p` with the old management firmware,
the management firmware resource is not correctly released,
which causes firmware related malfunction: all the access
to management firmware hangs.
It releases the management firmware resource when set id
mode operation is not supported.
Fixes: ccb9bc1dfa44 ("nfp: add 'ethtool --identify' support")
Signed-off-by: Gao Xiao <gao.xiao@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20220829101651.633840-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
ieee802154 for net 2022-08-29
- repeated word fix from Jilin Yuan.
- missed return code setting in the cc2520 driver by Li Qiong.
- fixing a potential race in by defering the workqueue destroy
in the adf7242 driver by Lin Ma.
- fixing a long standing problem in the mac802154 rx path to match
corretcly by Miquel Raynal.
* tag 'ieee802154-for-net-2022-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
ieee802154: cc2520: add rc code in cc2520_tx()
net: mac802154: Fix a condition in the receive path
net/ieee802154: fix repeated words in comments
ieee802154/adf7242: defer destroy_workqueue call
====================
Link: https://lore.kernel.org/r/20220829100308.2802578-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same GPIO line can be shared by multiple phys for the coma mode pin.
If that is the case then, all the other phys that share the same line
will failed to be probed because the access to the gpio line is not
non-exclusive.
Fix this by making access to the gpio line to be nonexclusive using flag
GPIOD_FLAGS_BIT_NONEXCLUSIVE. This allows all the other PHYs to be
probed.
Fixes: 738871b09250ee ("net: phy: micrel: add coma mode GPIO")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220830064055.2340403-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix wording in comments for the notifications coalescing feature.
Signed-off-by: Alvaro Karsz <alvaro.karsz@solid-run.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20220823073947.14774-1-alvaro.karsz@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TCP_FIN_WAIT2 and TCP_LAST_ACK were not handled, the connection is closing
so we can ignore them and avoid printing the "unhandled state"
warning message.
[ 1298.852386] nvmet_tcp: queue 2 unhandled state 5
[ 1298.879112] nvmet_tcp: queue 7 unhandled state 5
[ 1298.884253] nvmet_tcp: queue 8 unhandled state 5
[ 1298.889475] nvmet_tcp: queue 9 unhandled state 5
v2: Do not call nvmet_tcp_schedule_release_queue(), just ignore
the fin_wait2 and last_ack states.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
There's a goto missing in nvmet_setup_auth(), causing a kernel oops
when nvme_auth_extract_key() fails.
Reported-by: Tal Lossos <tallossos@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Lexar NM610 reports bogus eui64 values that appear to be the same across
all drives. Quirk them out so they are not marked as "non globally unique"
duplicates.
Signed-off-by: Shyamin Ayesh <me@shyamin.com>
[patch formatting]
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In some cases of failure (dialect mismatches) in SMB2_negotiate(), after
the request is sent, the checks would return -EIO when they should be
rather setting rc = -EIO and jumping to neg_exit to free the response
buffer from mempool.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
