| Age | Commit message (Collapse) | Author |
|---|
|
The tx-threshold parameter sets the TX FIFO low water threshold
trigger for the Altera 16550-FIFO32 soft IP.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Altera 16550 soft IP UART requires 2 additional registers for
TX FIFO threshold support. These 2 registers enable the TX FIFO
Low Watermark and set the TX FIFO Low Watermark.
Set the TX FIFO threshold to the FIFO size - tx_loadsz.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Initialize the tx_loadsz parameter from passed in devicetree
tx-threshold parameter.
The tx_loadsz is calculated as the number of bytes to fill FIFO
when tx-threshold is triggered.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the device tree binding needed to support the TX FIFO threshold
parameter.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As noted in commit:
81539169f283329f ("x86/dumpstack: Remove NULL task pointer convention")
... having a NULL task parameter imply current leads to subtle bugs in stack
walking code (so far seen on both 86 and arm64), makes callsites harder to
read, and is unnecessary as all callers have access to current.
As a step towards removing the problematic NULL-implies-current idiom entirely,
have the sysrq code explicitly pass current to show_stack.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USR2_DCDIN bit is tested for in register usr1. As the name
suggests the usr2 register should be used instead. This fixes
reading the Carrier detect status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: 90ebc4838666 ("serial: imx: repair and complete handshaking")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org> # 4.5+
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We get 2 warnings when building kernel with W=1:
drivers/tty/serial/stm32-usart.c:63:5: warning: no previous prototype for 'stm32_pending_rx' [-Wmissing-prototypes]
drivers/tty/serial/stm32-usart.c:88:15: warning: no previous prototype for 'stm32_get_char' [-Wmissing-prototypes]
In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add initialisation of control register and baud rate to
cdns_early_console_setup(), required when running kernel standalone
without a boot loader. Baud rate is only initialised when specified in
earlycon command-line option, otherwise it is assumed this has been
set by a boot loader. Updated Documentation/kernel-parameters.txt
accordingly.
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch Remove the unwated checks while reading the parity,framing,
overrun and Break detection errors.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
b1cf74970df5470ffbc8e7876a9edf5e3498ef94]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The existing interrupt handling logic has following issues.
- Upon a parity error with default configuration, the control
never comes out of the ISR thereby hanging Linux.
- The error handling logic around framing and parity error are buggy.
There are chances that the errors will never be captured.
This patch ensures that the status registers are cleared on all cases so
that a hang situation never arises.
Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
ac297e20d399850d7a8e373b6eccf2e183c15165 with manual conflict resolution]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Building this driver with a 64-bit dma_addr_t type results in
a compiler warning:
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_rx_probe':
drivers/tty/serial/stm32-usart.c:746:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_tx_probe':
drivers/tty/serial/stm32-usart.c:818:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
While the type conversion here is harmless, this hints at a different
problem: we pass an __iomem pointer into a DMA engine, which expects
a phys_addr_t. This happens to work because stm32 has no MMU and
ioremap() is an identity mapping here, but it's still an incorrect
API use. Using dma_addr_t is doubly wrong here, because that would
be the result of dma_map_single() rather than the physical address.
Using the mapbase instead fixes multiple issues:
- the warning is gone
- we don't go through ioremap in error
- the cast is gone, making it use the correct resource_size_t/phys_addr_t
type in the process.
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The problem with previous code was it rounded values in wrong
place and produced wrong baud rate in some cases.
Signed-off-by: Alexey Starikovskiy <aystarik@gmail.com>
[nicolas.ferre@atmel.com: port to newer kernel and add commit log]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Changes to support new security states of the iLO5 firmware.
- use BAR5 for CCB's for iLO5
- simplification of error handling
Signed-off-by: Mark Rusk <mark.rusk@hpe.com>
Signed-off-by: David Altobelli <david.altobelli@hpe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I've been reviewing changes proactively, and plan on doing
more of this work. I'm doing this early as I should be getting
e-mailed about proposed changes.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The result was being ignored and 0 was always returned.
Return the actual result instead.
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The patch does the following:
- fixes specifiers and removes explicit casting of the parameters
- joins literals to one line
- increases readability of the parameters
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Genwqe uses dma_alloc_coherent and depends on zero initialized memory. On
one occasion it ueses an explicit memset on others it uses un-initialized
memory.
This bug was covered because some archs actually return zero initialized
memory when using dma_alloc_coherent but this is by no means guaranteed.
Simply switch to dma_zalloc_coherent.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
image->lock is unlocked in some error handling path without take the
lock, so remove those unexpected unlock.
Fixes: 658bcdae9c67 ("vme: Adding Fake VME driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We get 4 warnings when building kernel with W=1:
drivers/vme/bridges/vme_fake.c:384:6: warning: no previous prototype for 'fake_lm_check' [-Wmissing-prototypes]
drivers/vme/bridges/vme_fake.c:619:6: warning: no previous prototype for 'fake_vmewrite8' [-Wmissing-prototypes]
drivers/vme/bridges/vme_fake.c:649:6: warning: no previous prototype for 'fake_vmewrite16' [-Wmissing-prototypes]
drivers/vme/bridges/vme_fake.c:679:6: warning: no previous prototype for 'fake_vmewrite32' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the test 'if (channel > 5)' is true, then we will return 'err' which
is known to be 0 at this point.
Return -EINVAL instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The auto incremented counter is not being used anymore, get rid of it.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some tools use bus ids to identify devices and they count on the fact
that these ids are persistent across reboot. This may be not true for
VMBus as we use auto incremented counter from alloc_channel() as such
id. Switch to using if_instance from channel offer, this id is supposed
to be persistent.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When performing DMA operations on a MCB device, the device needed
for using the DMA API is "mcb_device->bus_carrier".
This is rather lengthy, so a shortcut is introduced to struct mcb_device
in order to ensure the MCB device driver uses the correct device for DMA
operations.
Signed-off-by: Michael Moese <michael.moese@men.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to successfully perform DMA operations on PCI devices,
it is necessary to enble PCI bus mastering, so enable it by default.
Signed-off-by: Michael Moese <michael.moese@men.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The stall timer worker checks periodically if there is a stalled i/o
transaction. The issue with the current implementation is that the timer
is ticking also when there is no pending i/o transaction.
This patch provides a simple change that prevents rescheduling
of the delayed work when there is no pending i/o.
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
irq_get_irq_data() can return NULL, which results in a nasty crash.
Check its return value before passing it on to irqd_set_trigger_type().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Print the name of an undiscoverable attribute group and not the
pointer's address.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Kyle Jones <kyle@kf5jwc.us>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to (badf6d47f8a9 "usb: common: rework CONFIG_USB_COMMON logic")
we should select USB_COMMON at Kconfig when usb common stuffs are needed,
but some of Kconfig enties have not followed it, update them.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In USB20 specification, describes in chapter 9.4.5: The Remote Wakeup
field can be modified by the SetFeature() and ClearFeature() requests
using the DEVICE_REMOTE_WAKEUP feature selector.
In USB30 specification, also describes in chapter 9.4.5: The Function
Remote Wakeup field can be modified by the SetFeature() requests
using the FUNCTION_SUSPEND feature selector. In chapter 9.4.9 Set
Feature reference, it describes Function Remote Wake Enabled/Disabled
at suspend options by SET_FEATURE.
In USB30 specification only mentioned SetFeature(), so we need use
SET_FEATURE replace CLEAR_FEATURE to disable USB30 function remote
wakeup in suspend options.
Signed-off-by: Yonglong Wu <yonglong.wu@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit adds a new trigger responsible for turning on LED when USB
device gets connected to the selected USB port. This can can useful for
various home routers that have USB port(s) and a proper LED telling user
a device is connected.
The trigger gets its documentation file but basically it just requires
enabling it and selecting USB ports (e.g. echo 1 > ports/usb1-1).
There was a long discussion on design of this driver. Its current state
is a result of picking them most adjustable solution as others couldn't
handle all cases.
1) It wasn't possible for the driver to register separated trigger for
each USB port. Some physical USB ports are handled by more than one
controller and so by more than one USB port. E.g. USB 2.0 physical
port may be handled by OHCI's port and EHCI's port.
It's also not possible to assign more than 1 trigger to a single LED
and implementing such feature would be tricky due to syncing triggers
and sysfs conflicts with old triggers.
2) Another idea was to register trigger per USB hub. This wouldn't allow
handling devices with multiple USB LEDs and controllers (hubs)
controlling more than 1 physical port. It's common for hubs to have
few ports and each may have its own LED.
This final trigger is highly flexible. It allows selecting any USB ports
for any LED. It was also modified (comparing to the initial version) to
allow choosing ports rather than having user /guess/ proper names. It
was successfully tested on SmartRG SR400ac which has 3 USB LEDs,
2 physical ports and 3 controllers.
It was noted USB subsystem already has usb-gadget and usb-host triggers
but they are pretty trivial ones. They indicate activity only and can't
have ports specified.
In future it may be good idea to consider adding activity support to
usbport as well. This should allow switching to this more generic driver
and maybe marking old ones as obsolete.
This can be implemented with another sysfs file for setting mode. The
default mode wouldn't change so there won't be ABI breakage and so such
feature can be safely implemented later.
There was also an idea of supporting other devices (PCI, SDIO, etc.) but
as this driver already contains some USB specific code (and will get
more) these should be probably separated drivers (triggers).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver should initialize controller only, PHY initialization should
be handled by separated PHY driver. We already have phy-bcm-ns-usb2 in
place so let it makes its duty.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We get 1 warning when building kernel with W=1:
drivers/usb/core/hcd.c:2390:5: warning: no previous prototype for 'usb_bus_start_enum' [-Wmissing-prototypes]
In fact, these functions are declared in linux/usb/otg.h, so this patch
adds the missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.infradead.org/users/jjs/linux-tpmdd into ra-next
tpmdd reverts for Linux 4.9
Revert patches mistakenly included.
"Hi James,
I had a typo in my PR command:
git request-pull security/next git://git.infradead.org/users/jjs/linux-tpmdd.git master > tpmdd-next-20160915.txt
^^^^^^
That should have been the signed tag tpmdd-next-20160915. This caused
four commits slip into your tree that are not meant for 4.9 release. I
created a script to generate the signed tag + PR as a corrective
measure.
/Jarkko"
|
|
This reverts commit e17acbbb69d30836a8c12e2c09bbefab8656693e.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This reverts commit 9514ff1961c6f0f5983ba72d94f384bc13e0d4a1.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This reverts commit 0c22db435bf79d3cf3089df7ff198d4867df3c27.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This reverts commit e350e24694e447e6ab7312fffae5ca31a0bb5165.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This prevent future potential pointer leaks when an unprivileged eBPF
program will read a pointer value from its context. Even if
is_valid_access() returns a pointer type, the eBPF verifier replace it
with UNKNOWN_VALUE. The register value that contains a kernel address is
then allowed to leak. Moreover, this fix allows unprivileged eBPF
programs to use functions with (legitimate) pointer arguments.
Not an issue currently since reg_type is only set for PTR_TO_PACKET or
PTR_TO_PACKET_END in XDP and TC programs that can only be loaded as
privileged. For now, the only unprivileged eBPF program allowed is for
socket filtering and all the types from its context are UNKNOWN_VALUE.
However, this fix is important for future unprivileged eBPF programs
which could use pointers in their context.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
seccomp_phase1() does not exist anymore. Instead, update sample to use
__seccomp_filter(). While at it, set max locked memory to unlimited.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These samples fail to compile as 'struct flow_keys' conflicts with
definition in net/flow_dissector.h. Fix the same by renaming the
structure used in the sample.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following config options are required/recommended for running Docker:
Networking:
- CONFIG_NF_NAT_MASQUERADE_IPV4=m
- CONFIG_NF_NAT_MASQUERADE_IPV6=m
- CONFIG_IPVLAN=m
- CGROUP_NET_PRIO=y
Storage drivers:
- CONFIG_DM_THIN_PROVISIONING=m
- CONFIG_OVERLAY_FS=m
Scheduling:
- CONFIG_FAIR_GROUP_SCHED=y
- CONFIG_CFS_BANDWIDTH=y
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The MMCR2 register is available twice, one time with number 785
(privileged access), and one time with number 769 (unprivileged,
but it can be disabled completely). In former times, the Linux
kernel was using the unprivileged register 769 only, but since
commit 8dd75ccb571f3c92c ("powerpc: Use privileged SPR number
for MMCR2"), it uses the privileged register 785 instead.
The KVM-PR code then of course also switched to use the SPR 785,
but this is causing older guest kernels to crash, since these
kernels still access 769 instead. So to support older kernels
with KVM-PR again, we have to support register 769 in KVM-PR, too.
Fixes: 8dd75ccb571f3c92c48014b3dabd3d51a115ab41
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
On POWER8E and POWER8NVL, KVM-PR does not announce support for
64kB page sizes and 1TB segments yet. Looks like this has just
been forgotton so far, since there is no reason why this should
be different to the normal POWER8 CPUs.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Remove duplicate setting of the the "B" field when doing a tlbie(l).
In compute_tlbie_rb(), the "B" field is set again just before
returning the rb value to be used for tlbie(l).
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
We use logical negate where bitwise negate was intended. It means that
we never return -EINVAL here.
Fixes: ce11e48b7fdd ('KVM: PPC: E500: Add userspace debug stub support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
To get more coverage, enable COMPILE_TEST for this driver.
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This takes out the code that arranges to run two (or more) virtual
cores on a single subcore when possible, that is, when both vcores
are from the same VM, the VM is configured with one CPU thread per
virtual core, and all the per-subcore registers have the same value
in each vcore. Since the VTB (virtual timebase) is a per-subcore
register, and will almost always differ between vcores, this code
is disabled on POWER8 machines, meaning that it is only usable on
POWER7 machines (which don't have VTB). Given the tiny number of
POWER7 machines which have firmware that allows them to run HV KVM,
the benefit of simplifying the code outweighs the loss of this
feature on POWER7 machines.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
