| Age | Commit message (Collapse) | Author |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: (26 commits)
riscv: dts: starfive: jh7110: Fix GMAC configuration
riscv: dts: starfive - Add hwrng node for JH7110 SoC
riscv: dts: starfive - Add crypto and DMA node for JH7110
riscv: dts: starfive: Add mmc nodes on VisionFive 2 board
riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060
riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC
riscv: dts: starfive: jh7110: add the node and pins configuration for tdm
riscv: dts: starfive: jh7110: add dma controller node
riscv: dts: starfive: Add spi node and pins configuration
riscv: dts: starfive: Add USB dts node for JH7110
riscv: dts: starfive: Add USB and PCIe PHY nodes for JH7110
riscv: dts: starfive: jh7110: Add temperature sensor node and thermal-zones
riscv: dts: starfive: jh7100: Add temperature sensor node and thermal-zones
riscv: dts: starfive: visionfive 2: Add configuration of gmac and phy
riscv: dts: starfive: jh7110: Add ethernet device nodes
riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
riscv: dts: starfive: jh7110: Add syscon nodes
riscv: dts: starfive: jh7110: Add STGCRG/ISPCRG/VOUTCRG nodes
riscv: dts: starfive: jh7110: Add DVP and HDMI TX pixel external clocks
dt-bindings: clock: Add StarFive JH7110 Video-Output clock and reset generator
...
Link: https://lore.kernel.org/r/20230813-naturist-fragment-ac7d10c453ba@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt
mvebu dt for 6.6 (part 1)
Fix style issue and incorrect syntax
* tag 'mvebu-dt-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: marvell: dove: drop incorrect reg in fixed regulators
ARM: dts: marvell: armada: drop incorrect reg in fixed regulators
ARM: dts: marvell: add missing space before {
Link: https://lore.kernel.org/r/87h6p4t0lv.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt
mvebu dt64 for 6.6 (part 1)
Add the NAND Flash Controller on the AC5/AC5X SOC device tree
Fix style issue
* tag 'mvebu-dt64-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: Add NAND flash controller to AC5
arm64: dts: marvell: add missing space before {
Link: https://lore.kernel.org/r/87edk8t0kl.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fixed configuration to improve the speed of TCP RX.
Before:
# iperf3 -s
-----------------------------------------------------------
Server listening on 5201 (test #1)
-----------------------------------------------------------
Accepted connection from 192.168.1.4, port 47604
[ 5] local 192.168.1.3 port 5201 connected to 192.168.1.4 port 47612
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 36.3 MBytes 305 Mbits/sec
[ 5] 1.00-2.00 sec 35.6 MBytes 299 Mbits/sec
[ 5] 2.00-3.00 sec 36.5 MBytes 306 Mbits/sec
[ 5] 3.00-4.00 sec 36.5 MBytes 306 Mbits/sec
[ 5] 4.00-5.00 sec 35.7 MBytes 300 Mbits/sec
[ 5] 5.00-6.00 sec 35.4 MBytes 297 Mbits/sec
[ 5] 6.00-7.00 sec 37.1 MBytes 311 Mbits/sec
[ 5] 7.00-8.00 sec 35.6 MBytes 298 Mbits/sec
[ 5] 8.00-9.00 sec 36.4 MBytes 305 Mbits/sec
[ 5] 9.00-10.00 sec 36.3 MBytes 304 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.00 sec 361 MBytes 303 Mbits/sec receiver
After:
# iperf3 -s
-----------------------------------------------------------
Server listening on 5201 (test #1)
-----------------------------------------------------------
Accepted connection from 192.168.1.4, port 47710
[ 5] local 192.168.1.3 port 5201 connected to 192.168.1.4 port 47720
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 111 MBytes 932 Mbits/sec
[ 5] 1.00-2.00 sec 111 MBytes 934 Mbits/sec
[ 5] 2.00-3.00 sec 111 MBytes 934 Mbits/sec
[ 5] 3.00-4.00 sec 111 MBytes 934 Mbits/sec
[ 5] 4.00-5.00 sec 111 MBytes 934 Mbits/sec
[ 5] 5.00-6.00 sec 111 MBytes 935 Mbits/sec
[ 5] 6.00-7.00 sec 111 MBytes 934 Mbits/sec
[ 5] 7.00-8.00 sec 111 MBytes 935 Mbits/sec
[ 5] 8.00-9.00 sec 111 MBytes 934 Mbits/sec
[ 5] 9.00-10.00 sec 111 MBytes 934 Mbits/sec
[ 5] 10.00-10.00 sec 167 KBytes 933 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.00 sec 1.09 GBytes 934 Mbits/sec receiver
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Fixes: 1ff166c97972 ("riscv: dts: starfive: jh7110: Add ethernet device nodes")
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
[conor: converted to decimal per emil's request]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
dove-cubox.dtb: regulator@1: Unevaluated properties are not allowed ('reg' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
armada-370-dlink-dns327l.dtb: regulator@1: Unevaluated properties are not allowed ('reg' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
"make dtbs_check":
arch/arm/boot/dts/nuvoton-npcm730-gbs.dtb: i2c-switch@71: $nodename:0: 'i2c-switch@71' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
"make dtbs_check":
arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dtb: i2c-switch@70: $nodename:0: 'i2c-switch@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arm/boot/dts/aspeed-bmc-bytedance-g220a.dtb: i2c-switch@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
File names inside the file does not add much and just makes it
difficult to move the files, often the file name is not updated
and becomes wrong. Remove them.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This looks better and allows us to see the row and column numbers
more easily. Switch to this macro here.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This node does not follow the DT binding schema, correct this.
The arm,pl011 binding requires the first clock to be named "uartclk".
Should result in no functional change.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This node does not follow the DT binding schema, correct this.
All "regulator-fixed" are voltage type, so drop "regulator-type".
Should result in no functional change.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This node does not follow the DT binding schema, correct this.
Should result in no functional change.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This node does not follow the DT binding schema, correct this.
Should result in no functional change.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Writing this bit can be handled by the syscon-reboot driver.
Add this node to DT.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Fabian Vogt <fabian@ritter-vogt.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM changes for v6.6
1. Galaxy S II: correct LCD screen's physical size.
2. Add Samsung Galaxy Tab 3 8.0 boards (Exynos4212).
3. Galaxy S3 family: add USB connector and USB OTG. Full USB OTG still
seems not to work, but at least HDMI improved and dtbs_check is
happy.
4. Fix issues pointed out by dtbs_check and W=1: unit addresses, use
'gpios' suffix over 'gpio', update i2c-arb device node to newer
binding.
5. Few white-space cleanups.
* tag 'samsung-dt-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: samsung: exynos4412-midas: add USB connector and USB OTG
ARM: dts: samsung: exynos5250-snow: switch i2c-arb to new child variant
ARM: dts: samsung: exynos5250-snow: use 'gpios' suffix for i2c-arb
ARM: dts: samsung: fix Exynos4212 Tab3 makefile entries
ARM: dts: exynos: Add Samsung Galaxy Tab 3 8.0 boards
ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)
ARM: dts: samsung: s3c6410-mini6410: correct ethernet reg addresses (split)
ARM: dts: samsung: exynos4210-i9100: Fix LCD screen's physical size
ARM: dts: s5pv210: minor whitespace cleanup around '='
ARM: dts: exynos: minor whitespace cleanup around '='
Link: https://lore.kernel.org/r/20230810151250.220202-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.6
1. Add dedicated compatibles for PWM block.
2. Add PWM to ExynosAutov9 SADK board.
3. Few white-space and other cleanups.
* tag 'samsung-dt64-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: exynos5433-tm2: drop redundant status=okay
arm64: dts: exynos: add pwm node for exynosautov9-sadk
dt-bindings: pwm: samsung: add exynosautov9 compatible
arm64: dts: fsd: minor whitespace cleanup around '='
arm64: dts: exynos: minor whitespace cleanup around '='
arm64: dts: exynos: add missing space before {
Link: https://lore.kernel.org/r/20230810151250.220202-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into soc/dt
ASPEED device tree updates for 6.6
- New machines
* Inventec's Starscream AST2600 BMC, for a x86 server platform
* Meta's Yossemite 4 AST2600 BMC, for a multi-node server platform
- Big device tree rework for IBM's Power10 BMC platforms
- Updates for wedge400 and Mt Mitchell
- AST2600 I3C and VUART descriptions
* tag 'aspeed-6.6-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: Add AST2600 I3C control pins
ARM: dts: aspeed: everest: Move common devices up
ARM: dts: aspeed: everest: Reorganise FSI description
ARM: dts: aspeed: rainier: Reorganise FSI description
ARM: dts: aspeed: bonnell: Reorganise FSI description
ARM: dts: aspeed: Add P10 FSI descriptions
ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC
dt-bindings: arm: aspeed: add Facebook Yosemite 4 board
ARM: dts: aspeed: wedge400: Set eMMC max frequency
ARM: dts: aspeed: wedge400: Enable more ADC channels
ARM: dts: aspeed: Update spi alias in Facebook AST2500 Common dtsi
ARM: dts: aspeed: rainier: Remove TPM device
ARM: dts: aspeed: Add AST2600 VUARTs
ARM: dts: aspeed: mtmitchell: Add MCTP
ARM: dts: aspeed: mtmitchell: Update ADC sensors for Mt.Mitchell DVT systems
ARM: dts: aspeed: mtmitchell: Enable the BMC UART8 and UART9
ARM: dts: aspeed: Adding Inventec Starscream BMC
dt-bindings: arm: aspeed: add Inventec starscream-bmc
ARM: dts: aspeed: bonnell: Add DIMM SPD
Link: https://lore.kernel.org/r/CACPK8Xc76O5kLEAXRtbFXZcP=ObrKR0Kpez_er+zV2vZffZe7A@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into soc/dt
Devicetree changes for omaps for v6.6
Updates for opp and pinctrl nodes to follow the devicetree bindings.
* tag 'omap-for-v6.6/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: dts: ti: omap: Fix OPP table node names
arm: dts: ti: omap: am5729-beagleboneai: Drop the OPP
arm: dts: ti: omap: omap36xx: Rename opp_supply nodename
ARM: dts: ti: add missing space before {
ARM: dts: ti: split interrupts per cells
ARM: dts: Unify pinctrl-single pin group nodes for davinci
Link: https://lore.kernel.org/r/pull-1691658952-110529@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into soc/dt
Devicetree binding changes for omaps for v6.6
Just one change to get started on SoC yaml binding changes for omaps.
* tag 'omap-for-v6.6/dt-bindings-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
dt-bindings: omap: Partially convert omap.txt to yaml
Link: https://lore.kernel.org/r/pull-1691658952-110529@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
- Add D1 GPADC node
- Introduce support for OrangePi Zero 3 SBC
- Enable DT overlay support for Allwinner H3 boards
* tag 'sunxi-dt-for-6.6-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: Enable device-tree overlay support for sun8i-h3 pi devices
arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support
dt-bindings: arm: sunxi: document Orange Pi Zero 3 board name
arm64: dts: allwinner: h616: Split Orange Pi Zero 2 DT
riscv: dts: allwinner: d1: Add GPADC node
Link: https://lore.kernel.org/r/20230806180546.GA127039@jernej-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The defined value for "status" is "disabled", not "disable".
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230804225813.12493-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into soc/dt
Amlogic ARM64 DT changes for v6.6:
- Add initial support for A311D2
- Add AN400 board
- Add gpio_intc, power domain for C3 SoC
- Again some DT bindings fixes & cleanups
* tag 'amlogic-arm64-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: amlogic: drop cooling-[min|max]-state from pwm-fan
arm64: dts: amlogic: meson-g12-common: change aobus-pinctrl node name
arm64: dts: amlogic: meson-g12b-odroid-n2: fix usb hub hog name
arm64: dts: amlogic: drop redundant status=okay in sound nodes
arm64: dts: amlogic: meson-g12b-bananapi: switch to enable-gpios
arm64: dts: add support for C3 power domain controller
arm64: dts: Add gpio_intc node and pinctrl node for Amlogic C3 SoCs
arm64: dts: add board AN400
dt-bindings: arm: amlogic: add board AN400
arm64: dts: amlogic: minor whitespace cleanup around '='
arm64: dts: amlogic-t7-a311d2-khadas-vim4: add initial device-tree
dt-bindings: arm: amlogic: add Amlogic A311D2 bindings
Link: https://lore.kernel.org/r/d5f95654-ebcd-bd37-02f9-840e50b17e44@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/dt
Armv8 Juno/FVP update for v6.6
Just a single minor whitespace cleanup in couple of FVP device trees.
* tag 'juno-update-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: arm: minor whitespace cleanup around '='
Link: https://lore.kernel.org/r/20230804123223.3258086-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
soc/dt
arm64: ZynqMP DT changes for v6.6
- Describe caches
- Fix i2c gpio recovery description
- Setting up default i2c frequency
- Describe GEM TSU clock and assigned rates for SOMs
- Reserved 1MB for internal firmware usage
- Fix dwc3 IRQ description
- Describe interrupts by using macros
* tag 'zynqmp-dt-for-6.6' of https://github.com/Xilinx/linux-xlnx:
arm64: zynqmp: Describe interrupts by using macros
arm64: zynqmp: Fix dwc3 usb interrupt description
arm64: zynqmp: Add memory reserved node for k26 Kria SOM board
arm64: zynqmp: Assign TSU clock frequency for GEMs
arm64: zynqmp: Setting default i2c clock frequency to 400kHz
arm64: zynqmp: Fix open drain warning on ZynqMP
arm64: zynqmp: Add L2 cache nodes
Link: https://lore.kernel.org/r/fde6d7b4-c751-219d-3ec5-04e5bad2aa17@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into soc/dt
ARM: DT: HiSilicon ARM32 DT updates for v6.6
- Fix "status" values
* tag 'hisi-arm32-dt-for-6.6' of https://github.com/hisilicon/linux-hisi:
ARM: dts: hisilicon: Fix "status" values
Link: https://lore.kernel.org/r/64CC9B21.70907@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into soc/dt
ARM64: DT: HiSilicon ARM64 DT updates for v6.6
- Miscellaneous fixes according the DTS coding style
- Correct the clocks order of the sd0 for the hi3798cv200
* tag 'hisi-arm64-dt-for-6.6' of https://github.com/hisilicon/linux-hisi:
arm64: dts: hi3798cv200: Fix clocks order of sd0
arm64: dts: hisilicon: add missing space before {
arm64: dts: hisilicon: minor whitespace cleanup around '='
Link: https://lore.kernel.org/r/64CC99A3.5030701@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip ARM64 device tree updates for 6.6
It contains:
- one cleanup patch that removes whitespaces around '='
* tag 'microchip-dt64-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm64: dts: microchip: minor whitespace cleanup around '='
Link: https://lore.kernel.org/r/20230804044132.231508-1-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
AT91 device tree updates for 6.6
It contains:
- TCB timer nodes adition for at91-sama5d3_ksz9477_evb board
- device tee cleanups
* tag 'at91-dt-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: remove duplicated entries
ARM: dts: microchip: split interrupts per cells
ARM: dts: at91: ksz9477_evb: Add tx-internal-delay-ps property for port5
ARM: dts: at91: ksz9477_evb: Add missing timer nodes
ARM: dts: at91-vinco: Fix "status" values
ARM: dts: microchip: add missing space before {
ARM: dts: microchip: minor whitespace cleanup around '='
Link: https://lore.kernel.org/r/20230804044102.231448-1-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Each interrupt should be in its own cell. This is much more readable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20230730111536.98164-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.6
- Add Clocked Serial Interface (CSI) support for the RZ/V2M SoC,
- Add PMIC, RTC, and PWM support for the RZ/G2L, RZ/G2LC, and RZ/V2L
SMARC EVK development boards,
- Add PWM (MTU3a) support for the RZ/G2UL and RZ/Five SoCs,
- Add External interrupt (INTC-EX) support for the R-Car S4-8 SoC,
- Add LED support for the Spider development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: spider-cpu: Add GP LEDs
arm64: dts: renesas: r8a779f0: Add INTC-EX node
arm64: dts: renesas: rzg2ul-smarc: Add support for enabling MTU3
arm64: dts: renesas: r9a07g043: Add MTU3a node
ARM dts: renesas: armadillo800eva: Switch to enable-gpios
arm64: dts: renesas: rzg2lc-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: rzg2lc-smarc-som: Add PHY interrupt support for ETH0
riscv: dts: renesas: Clean up dtbs_check W=1 warning due to empty phy node
arm64: dts: renesas: rzg2lc-smarc: Add support for enabling MTU3
arm64: dts: renesas: rzg2l-smarc: Add support for enabling MTU3
arm64: dts: renesas: Add missing space before {
ARM: dts: renesas: Add missing space before {
arm64: dts: renesas: Minor whitespace cleanup around '='
arm64: dts: renesas: rzg2l-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: r9a09g011: Add CSI nodes
arm64: dts: renesas: rzg2l: Fix txdv-skew-psec typos
arm64: dts: renesas: rzg2l: Update overfow/underflow IRQ names for MTU3 channels
Link: https://lore.kernel.org/r/cover.1690545144.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
arm64: tegra: Device tree changes for v6.6-rc1
The majority of this is fixes all over the place for DT schema
validation warnings. However, there are also cleanups for some things in
DT and audio support is added on IGX Orin. Jetson Orin NX and Nano also
gain a new thermal trip point to help keep the device cool at moderate
loads.
* tag 'tegra-for-6.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (22 commits)
arm64: tegra: Add blank lines for better readability
arm64: tegra: Remove {clock,reset}-names from VIC powergate
arm64: tegra: Drop incorrect maxim,disable-etr on Smaug
arm64: tegra: Add SPI device tree nodes for Tegra234
arm64: tegra: Enable UARTA and UARTE for Orin Nano
arm64: tegra: Add UARTE device tree node on Tegra234
arm64: tegra: Adapt to LP855X bindings changes
arm64: tegra: Add PCIe and DP 3.3V supplies
arm64: tegra: Add missing reset-names for Tegra HS UART
arm64: tegra: Remove current-speed for SBSA UART
arm64: tegra: smaug: Remove reg-shift for high-speed UART
arm64: tegra: Remove dmas and dma-names for debug UART
arm64: tegra: Add 35°C trip point for Jetson Orin NX/Nano
arm64: tegra: Remove duplicate PCI nodes
arm64: tegra: Sort PCI nodes correctly on Orin
arm64: tegra: Add audio support for IGX Orin
arm64: tegra: Update CPU OPP tables
arm64: tegra: Fix HSUART for Smaug
arm64: tegra: Fix HSUART for Jetson AGX Orin
arm64: tegra: Add missing alias for NVIDIA IGX Orin
...
Link: https://lore.kernel.org/r/20230728094129.3587109-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
ARM: tegra: Device tree changes for v6.6-rc1
This contains various fixes for DT schema validation and the Pegatron
Chagall and Nexus 7 get specific compatible strings for the panels that
they use.
* tag 'tegra-for-6.6-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Provide specific compatible string for Nexus 7 panel
ARM: tegra: Use Hannstar HSD101PWW2 on Pegatron Chagall
ARM: tegra: Reuse I2C3 for NVEC
ARM: tegra: Add missing reset-names for Tegra HS UART
ARM: tegra: Remove reset-names for UART devices
ARM: tegra: Remove dmas and dma-names for debug UART
Link: https://lore.kernel.org/r/20230728094129.3587109-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
dt-bindings: Changes for v6.6-rc1
A number of Tegra-specific bindings are converted to json-schema and the
reserved-memory and BPMP bindings get support for Tegra264.
* tag 'tegra-for-6.6-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: firmware: Add support for tegra186-bpmp DRAM MRQ GSCs
dt-bindings: reserved-memory: Add support for DRAM MRQ GSCs
dt-bindings: thermal: tegra: Convert to json-schema
dt-bindings: arm: tegra: nvec: Convert to json-schema
dt-bindings: clock: tegra: Document Tegra132 compatible
dt-bindings: cpu: Document NVIDIA Tegra186 CCPLEX cluster
dt-bindings: serial: tegra-hsuart: Convert to json-schema
dt-bindings: arm: tegra: ahb: Convert to json-schema
dt-bindings: arm: tegra: flowctrl: Convert to json-schema
Link: https://lore.kernel.org/r/20230728094129.3587109-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add pinctrl support for the I3C1 and I3C2 pins.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230809134413.3614535-1-dylan_hung@aspeedtech.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Other systems have the SoC devices listed before the FSI description.
Move them up in order to make them similar.
Link: https://lore.kernel.org/r/20230809074921.116987-6-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Use the P10 quad FSI CFAM description to reduce duplication and add the
I2C responders and associated engines.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230809074921.116987-5-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Use the P10 quad FSI CFAM description to reduce duplication.
Link: https://lore.kernel.org/r/20230809074921.116987-4-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Use the P10 dual FSI CFAM description to reduce duplication.
Link: https://lore.kernel.org/r/20230809074921.116987-3-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
These will be used by BMCs attached to a IBM Power10 server CPU.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230809074921.116987-2-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add linux device tree entry for Yosemite 4 devices connected to BMC.
The Yosemite 4 is a Meta multi-node server platform, based on AST2600 SoC.
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230810070032.335161-3-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Document the new compatibles used on Facebook Yosemite 4.
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810070032.335161-2-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Set eMMC max frequency to 25MHz to prevent intermittent eMMC access
failures.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230803230324.731268-4-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Enable ASPEED-ADC channels 5-8 to support voltage monitoring of all the
Wedge400 hardware revisions.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230803230324.731268-3-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Set FMC controller to "spi0" in ast2500-facebook-netbmc-common.dtsi so
the spi bus is consistent with the flash labels defined in flash layout.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230803230324.731268-2-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
TPM is disabled in Rainier, remove TPM device.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Link: https://lore.kernel.org/r/20230725141606.1641080-2-lakshmiy@us.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The AST2600 has two more vuarts, placed between the existing two in the
memory map.
Link: https://lore.kernel.org/r/20230620042257.73665-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Enable MCTP driver on I2C3 bus for MCTP transaction
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20230620092537.20007-4-chanh@os.amperecomputing.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Change to use I2C ADC controller (ltc2497) for Mt.Mitchell DVT and
later hardware.
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20230620092537.20007-3-chanh@os.amperecomputing.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The BMC UART8 and UART9 were connected to the Secpro and Mpro console
of socket S1 on the Mt.Mitchell system.
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20230620092537.20007-2-chanh@os.amperecomputing.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
