| Age | Commit message (Collapse) | Author |
|---|
|
Set RCPI values in mt7996_mcu_sta_rate_ctrl_tlv(), which can make the
FW rate control algorithm be initialized with a better MCS selection
table.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Set peer address and aid for the BMC wtbl of station interface. For some
functions such as parsing MU_EDCA parameters from beacon, firmware will
need the peer address to do correct parsing.
Without this patch, MU uplink traffic would get suffered.
Reported-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When a BMC wtbl of station interface is correctly set with peer address,
HW will do rx header translation for broadcast data packets, which makes
mac80211 unable to find the corresponding ieee80211_sta and drop the
packets. To fix this, disable HW rx header translation for BMC entry.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Looks like this was missed in the initial patch that made
the conversion to the emulated chanctx drivers.
Fixes: 0a44dfc07074 ("wifi: mac80211: simplify non-chanctx drivers")
Tested-by: James Courtier-Dutton <james.dutton@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Even if it is not a real issue at the moment since concurrent access to
mcu message queue is protected by mcu mutex, make the code more robust
and move mcu queue free space check inside queue spinlock critical section.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Set intr1 to 0 in mt7996_irq_tasklet() in order to avoid possible
uninitialized variable usage if wed is not active for hif2.
Fixes: 83eafc9251d6 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Before sending suspend & wow command to FW, its length should be
4-bytes alignd.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
During chip recovery (e.g. chip reset), there is a possible situation that
kernel worker reset_work is holding the lock and waiting for kernel thread
stat_worker to be parked, while stat_worker is waiting for the release of
the same lock.
It causes a deadlock resulting in the dumping of hung tasks messages and
possible rebooting of the device.
This patch prevents the execution of stat_worker during the chip recovery.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <MingYen.Hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt7920e is a mt7921 series chipset with 802.11ax 2x2:2SS support.
The major difference is in firmware side only, at this moment.
This patch would add some mandatory changes for new chip id and
firmware download control.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fixes issues with scanning and low power output at some rates.
Fixes: f75e4779d215 ("wifi: mt76: mt7996: add txpower setting support")
Signed-off-by: Chad Monroe <chad@monroe.io>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The wcid can be NULL. It should be checked for validity before
dereferencing it to avoid crash.
Fixes: 098428c400ff ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This flag is needed for the PSE client reset. Fixes watchdog reset issues.
Fixes: c677dda16523 ("wifi: mt76: mt7603: improve watchdog reset reliablity")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use the correct WMM AC queue instead of the MGMT one to fix potential issues
with aggregation sequence number tracking. Drop non-bufferable packets.
Fixes: fca9615f1a43 ("mt76: mt7603: fix up hardware queue index for PS filtered packets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When pre-calibration data is missing, do not fail the driver probe.
Instead, just print a warning and fall back to regular calibration.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Send an update to the MCU whenever the settings change
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The MT76_MCU_RESET flag is only read on the main phy.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The MT76_MCU_RESET flag is only read on the main phy.
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Set correct beamformer capabilities for station vif in HE PHY
capabilities IE.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Do not report measurements if the airtime counter was cleared since the
last update (possibly by firmware)
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When queueing packets, only the MT76_RESET flag of the primary PHY
is checked. If the primary PHY is scanning or changing channels, this can
lead to packet loss for tx on the second PHY.
Fix this by passing the phy to the .tx_queue_skb op and using it to check
the correct flag.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Avoid potentially reusing uninitialized data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Improves initial rate selection after connecting
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Currently, when using WCN7850 or QCN9274 as AP, ath12k always performs down
grade phy mode operation regardless of whether the firmware supports EHT
capability or not and then vdev will start in HE mode. When stations that
support EHT capability try to connect to the AP, the AP will set phy mode
to EHT after receiving the association request packet, and then send
WMI_PEER_ASSOC_CMDID command to firmware, AP’s firmware will crash.
This is because when the ath12k_mac_copy_sband_iftype_data() function
handles EHT capability, it does not copy the EHT capability into the
iftype[band][type] array according to the interface type. So, interface
type should not be used as an index to get eht_cap in
ath12k_mac_check_down_grade_phy_mode() function.
To address this issue, use types_mask to select the eht_cap in
ath12k_mac_check_down_grade_phy_mode() function.
This patch affects QCN9274 and WCN7850 because they have the same issue.
Hostapd log:
wlo1: STA 02:03:7f:37:12:34 IEEE 802.11: Could not set STA to kernel driver
Kernel log:
[270894.816076] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_SET_PARAM cmd
[270894.816111] ath12k_pci 0000:03:00.0: failed to setup peer SMPS for vdev 0: -108
[270894.816122] ath12k_pci 0000:03:00.0: Failed to associate station: 02:03:7f:37:12:34
[270894.843389] ieee80211 phy5: Hardware restart was requested
[270894.843517] ath12k_pci 0000:03:00.0: failed to lookup peer 02:03:7f:37:12:34 on vdev 0
[270894.843616] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_DELETE cmd
[270894.843650] ath12k_pci 0000:03:00.0: failed to delete peer vdev_id 0 addr 02:03:7f:37:12:34 ret -108
[270894.843663] ath12k_pci 0000:03:00.0: Failed to delete peer: 02:03:7f:37:12:34 for VDEV: 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425083837.5340-1-quic_lingbok@quicinc.com
|
|
Chris's email address bounces and lore hasn't seen an email
from anyone with his name for almost a decade.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430233532.1356982-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
aelior@marvell.com bounces, we haven't seen Ariel on lore
since March 2022.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20240430233305.1356105-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Richard Gobert says:
====================
net: gro: add flush/flush_id checks and fix wrong offset in udp
This series fixes a bug in the complete phase of UDP in GRO, in which
socket lookup fails due to using network_header when parsing encapsulated
packets. The fix is to add network_offset and inner_network_offset to
napi_gro_cb and use these offsets for socket lookup.
In addition p->flush/flush_id should be checked in all UDP flows. The
same logic from tcp_gro_receive is applied for all flows in
udp_gro_receive_segment. This prevents packets with mismatching network
headers (flush/flush_id turned on) from merging in UDP GRO.
The original series includes a change to vxlan test which adds the local
parameter to prevent similar future bugs. I plan to submit it separately to
net-next.
This series is part of a previously submitted series to net-next:
https://lore.kernel.org/all/20240408141720.98832-1-richardbgobert@gmail.com/
v3 -> v4:
- Store network offsets, and use them only in udp_gro_complete flows
- Correct commit hash used in Fixes tag
- v3:
https://lore.kernel.org/netdev/20240424163045.123528-1-richardbgobert@gmail.com/
v2 -> v3:
- Add network_offsets and fix udp bug in a single commit to make backporting easier
- Write to inner_network_offset in {inet,ipv6}_gro_receive
- Use network_offsets union in tcp[46]_gro_complete as well
- v2:
https://lore.kernel.org/netdev/20240419153542.121087-1-richardbgobert@gmail.com/
v1 -> v2:
- Use network_offsets instead of p_poff param as suggested by Willem
- Check flush before postpull, and for all UDP GRO flows
- v1:
https://lore.kernel.org/netdev/20240412152120.115067-1-richardbgobert@gmail.com/
====================
Link: https://lore.kernel.org/r/20240430143555.126083-1-richardbgobert@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
GRO-GSO path is supposed to be transparent and as such L3 flush checks are
relevant to all UDP flows merging in GRO. This patch uses the same logic
and code from tcp_gro_receive, terminating merge if flush is non zero.
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
{inner_}network_offset to napi_gro_cb
Commits a602456 ("udp: Add GRO functions to UDP socket") and 57c67ff ("udp:
additional GRO support") introduce incorrect usage of {ip,ipv6}_hdr in the
complete phase of gro. The functions always return skb->network_header,
which in the case of encapsulated packets at the gro complete phase, is
always set to the innermost L3 of the packet. That means that calling
{ip,ipv6}_hdr for skbs which completed the GRO receive phase (both in
gro_list and *_gro_complete) when parsing an encapsulated packet's _outer_
L3/L4 may return an unexpected value.
This incorrect usage leads to a bug in GRO's UDP socket lookup.
udp{4,6}_lib_lookup_skb functions use ip_hdr/ipv6_hdr respectively. These
*_hdr functions return network_header which will point to the innermost L3,
resulting in the wrong offset being used in __udp{4,6}_lib_lookup with
encapsulated packets.
This patch adds network_offset and inner_network_offset to napi_gro_cb, and
makes sure both are set correctly.
To fix the issue, network_offsets union is used inside napi_gro_cb, in
which both the outer and the inner network offsets are saved.
Reproduction example:
Endpoint configuration example (fou + local address bind)
# ip fou add port 6666 ipproto 4
# ip link add name tun1 type ipip remote 2.2.2.1 local 2.2.2.2 encap fou encap-dport 5555 encap-sport 6666 mode ipip
# ip link set tun1 up
# ip a add 1.1.1.2/24 dev tun1
Netperf TCP_STREAM result on net-next before patch is applied:
net-next main, GRO enabled:
$ netperf -H 1.1.1.2 -t TCP_STREAM -l 5
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 5.28 2.37
net-next main, GRO disabled:
$ netperf -H 1.1.1.2 -t TCP_STREAM -l 5
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 5.01 2745.06
patch applied, GRO enabled:
$ netperf -H 1.1.1.2 -t TCP_STREAM -l 5
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 5.01 2877.38
Fixes: a6024562ffd7 ("udp: Add GRO functions to UDP socket")
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
KMSAN reported uninit-value access in __ip_make_skb() [1]. __ip_make_skb()
tests HDRINCL to know if the skb has icmphdr. However, HDRINCL can cause a
race condition. If calling setsockopt(2) with IP_HDRINCL changes HDRINCL
while __ip_make_skb() is running, the function will access icmphdr in the
skb even if it is not included. This causes the issue reported by KMSAN.
Check FLOWI_FLAG_KNOWN_NH on fl4->flowi4_flags instead of testing HDRINCL
on the socket.
Also, fl4->fl4_icmp_type and fl4->fl4_icmp_code are not initialized. These
are union in struct flowi4 and are implicitly initialized by
flowi4_init_output(), but we should not rely on specific union layout.
Initialize these explicitly in raw_sendmsg().
[1]
BUG: KMSAN: uninit-value in __ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481
__ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481
ip_finish_skb include/net/ip.h:243 [inline]
ip_push_pending_frames+0x4c/0x5c0 net/ipv4/ip_output.c:1508
raw_sendmsg+0x2381/0x2690 net/ipv4/raw.c:654
inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x274/0x3c0 net/socket.c:745
__sys_sendto+0x62c/0x7b0 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x130/0x200 net/socket.c:2199
do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3804 [inline]
slab_alloc_node mm/slub.c:3845 [inline]
kmem_cache_alloc_node+0x5f6/0xc50 mm/slub.c:3888
kmalloc_reserve+0x13c/0x4a0 net/core/skbuff.c:577
__alloc_skb+0x35a/0x7c0 net/core/skbuff.c:668
alloc_skb include/linux/skbuff.h:1318 [inline]
__ip_append_data+0x49ab/0x68c0 net/ipv4/ip_output.c:1128
ip_append_data+0x1e7/0x260 net/ipv4/ip_output.c:1365
raw_sendmsg+0x22b1/0x2690 net/ipv4/raw.c:648
inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x274/0x3c0 net/socket.c:745
__sys_sendto+0x62c/0x7b0 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x130/0x200 net/socket.c:2199
do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x6d/0x75
CPU: 1 PID: 15709 Comm: syz-executor.7 Not tainted 6.8.0-11567-gb3603fcb79b1 #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-1.fc39 04/01/2014
Fixes: 99e5acae193e ("ipv4: Fix potential uninit variable access bug in __ip_make_skb()")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Link: https://lore.kernel.org/r/20240430123945.2057348-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Antony Antony says:
====================
Inspired by the upcoming IP-TFS patch set, and confusions experienced in
the past due to lack of direction attribute on SAs, add a new direction
"dir" attribute. It aims to streamline the SA configuration process and
enhance the clarity of existing SA attributes.
This patch set introduces the 'dir' attribute to SA, aka xfrm_state,
('in' for input or 'out' for output). Alsp add validations of existing
direction-specific SA attributes during configuration and in the data
path lookup.
This change would not affect any existing use case or way of configuring
SA. You will notice improvements when the new 'dir' attribute is set.
====================
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
In one case the -1 is returned which is quite confusing code for
the wrong device ID, in another the ret is returning instead of
plain 0 that also confusing as readed may ask the possible meaning
of positive codes, which are never the case there. Convert both
to use explicit predefined error codes to make it clear what's going
on there.
Fixes: 5a04227326b0 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Link: https://lore.kernel.org/r/20240425142706.2440113-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240425142706.2440113-4-andriy.shevchenko@linux.intel.com
|
|
GPIO controller might not be available when driver is being probed.
There are plenty of reasons why, one of which is deferred probe.
Since GPIOs are optional, return any error code we got to the upper
layer, including deferred probe. With that in mind, use dev_err_probe()
in order to avoid spamming the logs.
Fixes: 5a04227326b0 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Link: https://lore.kernel.org/r/20240425142706.2440113-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240425142706.2440113-3-andriy.shevchenko@linux.intel.com
|
|
It seems driver missed the point of proper use of device property APIs.
Correct this by updating headers and calls respectively.
Fixes: 5a04227326b0 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240425142706.2440113-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240425142706.2440113-2-andriy.shevchenko@linux.intel.com
|
|
Commit 3e2f544dd8a33 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240426093156.2002258-2-leitao@debian.org
|
|
With commit 34d21de99cea9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core instead
of this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Move qtnfmac driver to leverage the core allocation.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240426093156.2002258-1-leitao@debian.org
|
|
Symptom:
When the hsuid attribute is set for the first time on an IQD Layer3
device while the corresponding network interface is already UP,
the kernel will try to execute a napi function pointer that is NULL.
Example:
---------------------------------------------------------------------------
[ 2057.572696] illegal operation: 0001 ilc:1 [#1] SMP
[ 2057.572702] Modules linked in: af_iucv qeth_l3 zfcp scsi_transport_fc sunrpc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6
nft_reject nft_ct nf_tables_set nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables libcrc32c nfnetlink ghash_s390 prng xts aes_s390 des_s390 de
s_generic sha3_512_s390 sha3_256_s390 sha512_s390 vfio_ccw vfio_mdev mdev vfio_iommu_type1 eadm_sch vfio ext4 mbcache jbd2 qeth_l2 bridge stp llc dasd_eckd_mod qeth dasd_mod
qdio ccwgroup pkey zcrypt
[ 2057.572739] CPU: 6 PID: 60182 Comm: stress_client Kdump: loaded Not tainted 4.18.0-541.el8.s390x #1
[ 2057.572742] Hardware name: IBM 3931 A01 704 (LPAR)
[ 2057.572744] Krnl PSW : 0704f00180000000 0000000000000002 (0x2)
[ 2057.572748] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:3 PM:0 RI:0 EA:3
[ 2057.572751] Krnl GPRS: 0000000000000004 0000000000000000 00000000a3b008d8 0000000000000000
[ 2057.572754] 00000000a3b008d8 cb923a29c779abc5 0000000000000000 00000000814cfd80
[ 2057.572756] 000000000000012c 0000000000000000 00000000a3b008d8 00000000a3b008d8
[ 2057.572758] 00000000bab6d500 00000000814cfd80 0000000091317e46 00000000814cfc68
[ 2057.572762] Krnl Code:#0000000000000000: 0000 illegal
>0000000000000002: 0000 illegal
0000000000000004: 0000 illegal
0000000000000006: 0000 illegal
0000000000000008: 0000 illegal
000000000000000a: 0000 illegal
000000000000000c: 0000 illegal
000000000000000e: 0000 illegal
[ 2057.572800] Call Trace:
[ 2057.572801] ([<00000000ec639700>] 0xec639700)
[ 2057.572803] [<00000000913183e2>] net_rx_action+0x2ba/0x398
[ 2057.572809] [<0000000091515f76>] __do_softirq+0x11e/0x3a0
[ 2057.572813] [<0000000090ce160c>] do_softirq_own_stack+0x3c/0x58
[ 2057.572817] ([<0000000090d2cbd6>] do_softirq.part.1+0x56/0x60)
[ 2057.572822] [<0000000090d2cc60>] __local_bh_enable_ip+0x80/0x98
[ 2057.572825] [<0000000091314706>] __dev_queue_xmit+0x2be/0xd70
[ 2057.572827] [<000003ff803dd6d6>] afiucv_hs_send+0x24e/0x300 [af_iucv]
[ 2057.572830] [<000003ff803dd88a>] iucv_send_ctrl+0x102/0x138 [af_iucv]
[ 2057.572833] [<000003ff803de72a>] iucv_sock_connect+0x37a/0x468 [af_iucv]
[ 2057.572835] [<00000000912e7e90>] __sys_connect+0xa0/0xd8
[ 2057.572839] [<00000000912e9580>] sys_socketcall+0x228/0x348
[ 2057.572841] [<0000000091514e1a>] system_call+0x2a6/0x2c8
[ 2057.572843] Last Breaking-Event-Address:
[ 2057.572844] [<0000000091317e44>] __napi_poll+0x4c/0x1d8
[ 2057.572846]
[ 2057.572847] Kernel panic - not syncing: Fatal exception in interrupt
-------------------------------------------------------------------------------------------
Analysis:
There is one napi structure per out_q: card->qdio.out_qs[i].napi
The napi.poll functions are set during qeth_open().
Since
commit 1cfef80d4c2b ("s390/qeth: Don't call dev_close/dev_open (DOWN/UP)")
qeth_set_offline()/qeth_set_online() no longer call dev_close()/
dev_open(). So if qeth_free_qdio_queues() cleared
card->qdio.out_qs[i].napi.poll while the network interface was UP and the
card was offline, they are not set again.
Reproduction:
chzdev -e $devno layer2=0
ip link set dev $network_interface up
echo 0 > /sys/bus/ccwgroup/devices/0.0.$devno/online
echo foo > /sys/bus/ccwgroup/devices/0.0.$devno/hsuid
echo 1 > /sys/bus/ccwgroup/devices/0.0.$devno/online
-> Crash (can be enforced e.g. by af_iucv connect(), ip link down/up, ...)
Note that a Completion Queue (CQ) is only enabled or disabled, when hsuid
is set for the first time or when it is removed.
Workarounds:
- Set hsuid before setting the device online for the first time
or
- Use chzdev -d $devno; chzdev $devno hsuid=xxx; chzdev -e $devno;
to set hsuid on an existing device. (this will remove and recreate the
network interface)
Fix:
There is no need to free the output queues when a completion queue is
added or removed.
card->qdio.state now indicates whether the inbound buffer pool and the
outbound queues are allocated.
card->qdio.c_q indicates whether a CQ is allocated.
Fixes: 1cfef80d4c2b ("s390/qeth: Don't call dev_close/dev_open (DOWN/UP)")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430091004.2265683-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The alc_spec.power_hook is defined only with CONFIG_PM, and the recent
fix overlooked it, resulting in a build error without CONFIG_PM.
Fix it with the simple ifdef and set __maybe_unused for the function.
We may drop the whole CONFIG_PM dependency there, but it should be
done in a separate cleanup patch later.
Fixes: 1e707769df07 ("ALSA: hda/realtek - Set GPIO3 to default at S4 state for Thinkpad with ALC1318")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202405012104.Dr7h318W-lkp@intel.com/
Message-ID: <20240502062442.30545-1-tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove unnecessary includes from driver. The first step is to add
necessary includes to driver's header files to make them can be included
individually. Then, driver's C files include driver's header files first,
and check if still missed header files of kernel.
The results show that most C files only include driver's header files.
Only core.c needs to include additional linux/firmware.h.
Also sort includes in alphabetic order.
Compile tested only.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240429024711.30992-1-pkshih@realtek.com
|
|
The driver is already in a directory named rtl8xxxu, there's no need to
duplicate that in the filename as well. Now file listing looks a lot more
reasonable:
8188e.c 8192c.c 8192f.c 8723a.c core.c Makefile rtl8xxxu.h
8188f.c 8192e.c 8710b.c 8723b.c Kconfig regs.h
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426141939.3881678-2-kvalo@kernel.org
|
|
I noticed by random that rtl8xxxu includes linux/wireless.h even though it
doesn't need it. While investigating a bit more I found even more unused
include files:
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ethtool.h>
It looks like that the includes are just copied to every file without checking
if the file really needs the include. So more includes could be removed but
that would need more careful analysis per each file.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426141939.3881678-1-kvalo@kernel.org
|
|
Power sequence is a flow to enable/disable WiFi card with hardware
parameters. Adjust power and clock parameters according to results
of internal simulation and verification, so apply them to have better
power consumption.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426061200.44262-2-pkshih@realtek.com
|
|
Some Wi-Fi chips meet card lost issue due to unstable hardware signal of
GPIO pins during power off. Reset AFEDIG register before BB reset in
power off sequence could avoid unstable signal and fix the issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426061200.44262-1-pkshih@realtek.com
|
|
A few of the shared functions need small changes for the USB driver:
- firmware loading
- efuse reading
- rate mask updating
- rf register reading
- initial gain for scanning
Also, add a few macros to wifi.h and initialise rtlhal.interfaceindex
for USB devices.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/28100330-f421-4b85-b41b-f1045380cef2@gmail.com
|
|
Improve readability:
* add empty lines
* use abs_diff in rtl92d_dm_txpower_tracking_callback_thermalmeter
* roll up repeated statements into a for loop in
rtl92d_dm_txpower_tracking_callback_thermalmeter
* shorten lines by replacing many instances of "rtlpriv->dm" with "dm"
pointer in rtl92d_dm_txpower_tracking_callback_thermalmeter
* sort some declarations by length
* refactor _rtl92d_get_txpower_writeval_by_regulatory a little
* refactor _rtl92de_readpowervalue_fromprom a little
Delete unused structs tag_dynamic_init_gain_operation_type_definition
and swat.
Simplify rtl92d_fill_h2c_cmd a little and delete a pointless wrapper
function.
Tested with a single MAC single PHY USB dongle from Aliexpress labelled
"CC&C WL-6210-V3".
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/f6acfa78-2f4e-47f1-95d4-65aa77510113@gmail.com
|
|
Create the new module rtl8192d-common and move some code into it from
rtl8192de. Now the rtl8192de driver (PCI) and the new rtl8192du driver
(USB) can share some of the code.
This is mostly the code that required little effort to make it
shareable. There are a few more functions which they could share, with
more changes.
Add phy_iq_calibrate member to struct rtl_hal_ops to allow moving the
TX power tracking code from dm.c.
The other changes in this patch are adjusting whitespace, renaming some
functions, making some arrays const, and making checkpatch.pl less
unhappy.
rtl8192de is compile-tested only. rtl8192d-common is tested with the
new rtl8192du driver.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/69c4358a-6fbf-4433-92a6-341c83e9dd48@gmail.com
|
|
Structs rx_desc_92d and rx_fwinfo_92d will not work for big endian
systems.
Delete rx_desc_92d because it's big and barely used, and instead use
the get_rx_desc_rxmcs and get_rx_desc_rxht functions, which work on big
endian systems too.
Fix rx_fwinfo_92d by duplicating four of its members in the correct
order.
Tested only with RTL8192DU, which will use the same code.
Tested only on a little endian system.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/698463da-5ef1-40c7-b744-fa51ad847caf@gmail.com
|
|
Some (all?) management frames are incorrectly reported to mac80211 as
decrypted when actually the hardware did not decrypt them. This results
in speeds 3-5 times lower than expected, 20-30 Mbps instead of 100
Mbps.
Fix this by checking the encryption type field of the RX descriptor.
rtw88 does the same thing.
This fix was tested only with rtl8192du, which will use the same code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/4d600435-f0ea-46b0-bdb4-e60f173da8dd@gmail.com
|
