summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-08-22drivers:misc: ti-st: free skb on firmware downloadPavan Savoy
If during validation of the firmware download the data doesn't match what is expected out of the chip, this calls for a firmware download failure and a retry. Free the SKB which collects response during such scenarios. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22drivers:misc: ti-st: wait for completion at failPavan Savoy
When the line discipline install fails for reasons such as missing user-space UIM or broken communication between UIM and ST driver, then the ST attempts/retries to request for ldisc installation again. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22drivers:misc: ti-st: reinit completion before sendPavan Savoy
download firmware behaves differently at different times, when logs are enabled and the system is loaded, the wait_for_completion is able to wait for every send, However during other times the wait does not happen. So, for reliability reinitializing the completion before every send, makes sure the wait happens for every send. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22drivers:misc: ti-st: fail-safe on wrong pkt typeVijay Badawadagi
Texas Instrument's shared transport driver interpret incoming data from the UART based on the various protocol drivers registered to the driver such as btwilink driver or FM or GPS driver which provide logical channel IDs. In case of bad-behavior from chip such as HCI Event response for a GPS command or a HCI Event (h/w error event) for a FM response & In case of bad-behavior from UART driver such as dropping data bytes a fail-safe is required to avoid kernel panic. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Vijay Badawadagi <bvijay@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22drivers:misc: ti-st: reinit completion on ver readPavan Savoy
After the version information has been read, the completion which assists in wait_for_completion during the firmware send/wait sequence is being re-used and hence this needs to be re-initialised for fool proof firmware download retries. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22drivers:misc:ti-st: platform hooks for chip statesPavan Savoy
Certain platform specific or Host-WiLink Interface specific actions would be required to be taken when the chip is being enabled and after the chip is disabled such as configuration of the mux modes for the GPIO of host connected to the nshutdown of the chip or relinquishing UART after the chip is disabled. Similar actions can also be taken when the chip is in deep sleep or when the chip is awake. Performance enhancements such as configuring the host to run faster when chip is awake and slower when chip is asleep can also be made here. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22drivers:misc: ti-st: avoid a misleading dbg msgPavan Savoy
Previously the private data of each protocol registered to use ST was used to determine whether the protocol was registered to use shared transport or otherwise. However, now a flag is_registered is maintained to identify whether a protocol intends to use ST. Upon closing of the UART the error message relevant to this lack of un-registration was misleading and this patch fixes that. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22base/devres.c: quiet sparse noise about context imbalanceH Hartley Sweeten
devres_release_all and devres_release_group both aquire the lock &dev->devres_lock but the release of that lock is done in release_nodes. This results in sparse noise about context imbalance. Add a lock annotation to release_nodes to quiet this noise. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22pti: add missing CONFIG_PCI dependencyHeiko Carstens
allmodconfig compile fails on s390 because of the new PTI driver: drivers/misc/pti.c:407:3: error: implicit declaration of function 'pci_iounmap' drivers/misc/pti.c:410:3: error: implicit declaration of function 'pci_release_region' Add a 'depends on PCI' statement so it doesn't get compiled. Cc: J Freyensee <james_p_freyensee@linux.intel.com> Signed-off-by: Tracey Dent <tdent48227@gmail.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22hwmon: (ntc_thermistor) Simplify if sequenceGuenter Roeck
Replace unnecessary if with else statement. This fixes the following (false) compile warning reported with some combinations of C compiler version and configuration. drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp': drivers/hwmon/ntc_thermistor.c:225: warning: 'low' may be used uninitialized in this function drivers/hwmon/ntc_thermistor.c:225: note: 'low' was declared here drivers/hwmon/ntc_thermistor.c:225: warning: 'high' may be used uninitialized in this function drivers/hwmon/ntc_thermistor.c:225: note: 'high' was declared here drivers/hwmon/ntc_thermistor.c:294: warning: 'temp' may be used uninitialized in this function Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Jean Delvare <khali@linux-fr.org>
2011-08-22USB option driver K3765/K4505 avoid CDC_DATA interfaceAndrew Bird
Currently the Option driver avoids binding interface 1 on Huawei K3765 and K4505 broadband modems as it should be handled by the cdc_ether driver instead. This patch ensures we don't bind the interface 2 on those devices as that is CDC_DATA. Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22USB: option: add YUGA device id to driverGavin.zhu
Signed-off-by: Gavin.zhu <gavin.kx@qq.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22usb: s5p-ehci: fix a NULL pointer deferenceYulgon Kim
This patch fixes a NULL pointer deference. A NULL pointer dereference happens since s5p_ehci->hcd field is not initialized yet in probe function. [jg1.han@samsung.com: edit commit message] Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com> Signed-off-by: Jingoo Han <jg1.han@samsung.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ↵Wang Zhi
ehci_bus_resume(). From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss the action of clearing PORT_RESUME. This will cause unexpected long resume signal on USB bus. Signed-off-by: Wang Zhi <zhi.wang@windriver.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22USB option driver add PID of Huawei Vodafone K4605Andrew Bird
This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband modem to option.c. This is necessary so that the driver gets loaded on demand without the intervention of usb_modeswitch. This has the benefit of it becoming available faster and also ensures that the option driver is not bound to a network interface that should be claimed by suitable network driver. Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by: Alex Chiang <achiang@canonical.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22USB option driver add PID of Huawei Vodafone K3806Andrew Bird
This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband modem to option.c. This is necessary so that the driver gets loaded on demand without the intervention of usb_modeswitch. This has the benefit of it becoming available faster and also ensures that the option driver is not bound to a network interface that should be claimed by cdc_ether. Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by: Alex Chiang <achiang@canonical.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22Merge branch 'for-greg' of ↵Greg Kroah-Hartman
master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb into usb-linus * 'for-greg' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb: usb: musb: gadget: fix error path usb: gadget: f_phonet: unlock in error case usb: musb: blackfin: include prefetch head file usb: musb: tusb6010: fix compilation usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h usb: musb: cppi: fix build errors due to DBG and missing musb variable usb: musb: ux500: replace missing DBG with dev_dbg usb: musb: ux500: set dma config for both src and dst usb: musb: fix oops on musb_gadget_pullup usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1) usb: gadget: hid: don't STALL when processing a HID Descriptor request usb: musb: fix Kconfig usb: musb: tusb6010_omap: fix build failure: error: 'musb' undeclared usb: gadget: composite: fix bMaxPacketSize for SuperSpeed usb: gadget: fusb300: remove #if 0 block usb: gadget: s3c2410_udc: fix unterminated platform_device_id table
2011-08-22Merge branch 'for-usb-linus' of ↵Greg Kroah-Hartman
git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus * 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci: xhci: Handle zero-length isochronous packets. USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth. xhci: Remove TDs from TD lists when URBs are canceled. xhci: Fix failed enqueue in the middle of isoch TD. xhci: Fix memory leak during failed enqueue. xHCI: report USB2 port in resuming as suspend xHCI: fix port U3 status check condition
2011-08-22ceph: fix memory leakNoah Watkins
kfree does not clean up indirect allocations in ceph_fs_client and ceph_options (e.g. snapdir_name). Signed-off-by: Noah Watkins <noahwatkins@gmail.com> Signed-off-by: Sage Weil <sage@newdream.net>
2011-08-22Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
2011-08-22target: Convert acl_node_lock to be IRQ-disablingRoland Dreier
With qla2xxx, acl_node_lock is taken inside qla2xxx's hardware_lock, which is taken in hardirq context. This means acl_node_lock must become an IRQ-disabling lock; in particular this fixes lockdep warnings along the lines of ====================================================== [ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ] (&(&se_tpg->acl_node_lock)->rlock){+.....}, at: [<ffffffffa026f872>] transport_deregister_session+0x92/0x140 [target_core_mod] and this task is already holding: (&(&ha->hardware_lock)->rlock){-.-...}, at: [<ffffffffa017c5e7>] qla_tgt_stop_phase1+0x57/0x2c0 [qla2xxx] which would create a new lock dependency: (&(&ha->hardware_lock)->rlock){-.-...} -> (&(&se_tpg->acl_node_lock)->rlock){+.....} but this new dependency connects a HARDIRQ-irq-safe lock: (&(&ha->hardware_lock)->rlock){-.-...} to a HARDIRQ-irq-unsafe lock: (&(&se_tpg->acl_node_lock)->rlock){+.....} Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Make locking in transport_deregister_session() IRQ safeRoland Dreier
At least the tcm_qla2xxx fabric driver calls into transport_deregister_session() while holding an IRQ-disabled spinlock, so the inner locking needs to use spin_lock_irqsave() instead of spin_lock_bh(). This fixes warnings seen with tcm_qla2xxx like: WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x98/0xb0() Call Trace: [<ffffffff8104e65f>] warn_slowpath_common+0x7f/0xc0 [<ffffffff8104e6ba>] warn_slowpath_null+0x1a/0x20 [<ffffffff81055368>] local_bh_enable_ip+0x98/0xb0 [<ffffffff814d5284>] _raw_spin_unlock_bh+0x14/0x20 [<ffffffffa027b7f6>] transport_deregister_session+0x96/0x180 [target_core_mod] [<ffffffffa00f7731>] tcm_qla2xxx_free_session+0xd1/0x170 [tcm_qla2xxx] [<ffffffffa01b9173>] qla_tgt_sess_put+0xc3/0x140 [qla2xxx] [<ffffffffa01bf40f>] qla_tgt_stop_phase1+0x8f/0x2c0 [qla2xxx] [<ffffffffa00f735e>] tcm_qla2xxx_tpg_store_enable+0x6e/0xd0 [tcm_qla2xxx] [<ffffffffa026ca29>] target_fabric_tpg_attr_store+0x39/0x40 [target_core_mod] [<ffffffffa00a575d>] configfs_write_file+0xbd/0x120 [configfs] [<ffffffff811464a6>] vfs_write+0xc6/0x180 [<ffffffff811467c1>] sys_write+0x51/0x90 [<ffffffff814dd382>] system_call_fastpath+0x16/0x1b Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22tcm_fc: init/exit functions should not be protected by "#ifdef MODULE"Roland Dreier
There's no need for the #ifdef protection when building into the kernel, and in fact we need the module_init() for the initialization function to be called. Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Print subpage too for unhandled MODE SENSE pagesRoland Dreier
Make a log message more useful by printing both the page and subpage that an initiator is requesting. Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22iscsi-target: Fix iscsit_allocate_se_cmd_for_tmr failure path bugsDan Carpenter
This patch fixes two bugs in allocation failure handling in iscsit_allocate_se_cmd_for_tmr(): This first reported by DanC is a free-after call to transport_free_se_cmd(), this patch drops the transport_free_se_cmd() call all together, as iscsit_release_cmd() will release existing allocations as expected. The second is a bug where iscsi_cmd_t was being leaked on a cmd->tmr_req allocation failure, so make this jump to iscsit_release_cmd() as well. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22iscsi-target: Implement iSCSI target IPv6 address printing.Chris Boot
The iSCSI target configfs code to print out an initiator's IPv6 address is not fully implemented. This patch uses snprintf() with the "%pI6c" format string to format the IPv6 address for display purposes. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Fix task SGL chaining breakage with transport_allocate_data_tasksNicholas Bellinger
This patch fixes two bugs associated with transport_do_task_sg_chain() operation where transport_allocate_data_tasks() was incorrectly setting task_padded_sg for all tasks, and causing bogus task->task_sg_nents assignments + OOPsen with fabrics depending upon this code. The first bit here adds a task_sg_nents_padded check in transport_allocate_data_tasks() to include an extra SGL vector when necessary for tasks that expect to be linked using sg_chain(). The second change involves making transport_do_task_sg_chain() properly account for the extra SGL vector when task->task_padded_sg is set for the non trailing ->task_sg or single ->task_sg allocations. Note this patch also removes the BUG_ON(!task->task_padded_sg) check within transport_do_task_sg_chain() as we expect this to happen normally with the updated logic in transport_allocate_data_tasks(), along with being bogus for CONTROL_SG_IO_CDB type payloads. So far this bugfix has been tested with tcm_qla2xxx and iblock backends in (task_count > 1)( and (task_count == 1) operation. Reported-by: Kiran Patil <kiran.patil@intel.com> Cc: Kiran Patil <kiran.patil@intel.com> Cc: Andy Grover <agrover@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Fix task count > 1 handling breakage and use max_sector page alignmentNicholas Bellinger
This patch addresses recent breakage with multiple se_task (task_count > 1) operation following backend dev->se_sub_dev->se_dev_attrib.max_sectors in new transport_allocate_data_tasks() code. The initial bug here was a bogus task->task_sg_nents assignment in transport_allocate_data_tasks() based on the passed parameter, which now uses DIV_ROUND_UP(task_size, PAGE_SIZE) to determine the proper number of per task SGL entries for the (task_count > 1) case. This also means we now need to enforce a PAGE_SIZE aligned max_sector count value for this to work as expected without bringing back the pre v3.1 transport_map_mem_to_sg() logic to handle SGL offsets across multiple tasks. So this patch adds se_dev_align_max_sectors() to round down max_sectors as necessary to ensure this alignment via se_dev_set_default_attribs() and se_dev_align_max_sectors() and keeps it simple for (task_count > 1) operation. So far this bugfix has been tested with (task_count > 1) operation using iscsi-target and iblock backends. Reported-by: Chris Boot <bootc@bootc.net> Cc: Kiran Patil <kiran.patil@intel.com> Cc: Andy Grover <agrover@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Add missing DATA_SG_IO transport_cmd_get_valid_sectors checkNicholas Bellinger
This patch adds the missing transport_cmd_get_valid_sectors() check for SCF_SCSI_DATA_SG_IO_CDB type payloads to ensure that a received LBA + range does not exeed past the end of associated backend struct se_device. This patch also fixes a bug in the failure path of transport_new_cmd_obj() where this check can fail, so change to use a signed 'rc' and return '-EINVAL' to signal proper transport_generic_request_failure() handling. Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Fix SYNCHRONIZE_CACHE zero LBA + range breakageNicholas Bellinger
This patch fixes a SYNCHRONIZE_CACHE CDB handling bug with IBLOCK/FILEIO backends where transport_cmd_get_valid_sectors() was incorrectly rejecting a zero LBA + range CDB from being processed, and returning CHECK_CONDITION. This includes changing transport_cmd_get_valid_sectors() to return '0' on success and '-EINVAL' on failure (this makes more sense than sectors), and to only check transport_cmd_get_valid_sectors() when a non zero LBA + range SYNCHRONIZE_CACHE operation has been receieved for the non passthrough case. Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Remove duplicate task completions in transport_emulate_control_cdbNicholas Bellinger
This patch removes a duplicate set of transport_complete_task() calls in target_emulate_unmap() and target_emulate_write_same() as the completion call is already done within transport_emulate_control_cdb() This patch also adds a check in transport_emulate_control_cdb() for the existing SCF_EMULATE_CDB_ASYNC flag currently used by SYNCHRONIZE_CACHE in order to handle IMMEDIATE processing. Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Fix WRITE_SAME usage with transport_get_sizeNicholas Bellinger
For all flavours of WRITE_SAME, we only expect to handle a single block of data-out buffer payload, regardless of the number of logical blocks presented in the CDB. This patch changes all flavours of WRITE_SAME in transport_generic_cmd_sequencer() to pass '1' into transport_get_size() instead of the extracted 'sectors' to properly handle the default usage of sg_write_same without the --xferlen parameter. Reported-by: Eric Seppanen <eric@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
2011-08-22target: Add WRITE_SAME (10) parsing and refactor passthrough checksNicholas Bellinger
This patch adds initial WRITE_SAME (10) w/ UNMAP=1 support following updates in sbcr26 to allow UNMAP=1 for the non 16 + 32 byte CDB case. It also refactors current pSCSI passthrough passthrough checks into target_check_write_same_discard() ahead of UNMAP=0 w/ write payload support into target_core_iblock.c. This includes the support for handling WRITE_SAME in transport_emulate_control_cdb(), and converts target_emulate_write_same to accept num_blocks directly for WRITE_SAME, WRITE_SAME_16 and WRITE_SAME_32. Reported-by: Eric Seppanen <eric@purestorage.com> Cc: Roland Dreier <roland@purestorage.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
2011-08-22target: Fix write payload exception handling with ->new_cmd_mapNicholas Bellinger
This patch fixes a bug for fabrics using tfo->new_cmd_map() that are expect transport_generic_request_failure() to be calling transport_send_check_condition_and_sense() for both READ and WRITE, instead of only for READ exceptions. This was originally observed with a failed WRITE_SAME_16 w/ unmap=0 using tcm_loop. Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22iscsi-target: forever loop bug in iscsit_attach_ooo_cmdsn()Dan Carpenter
This patch fixes a forever loop bug in iscsit_attach_ooo_cmdsn() while walking sess->sess_ooo_cmdsn_list when the received CmdSN is less than the tail of the list. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22iscsi-target: remove duplicate returnDan Carpenter
We returned on the line before already. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Convert target_core_rd.c to use use BUG_ONJulia Lawall
Use BUG_ON(x) rather than if(x) BUG(); The semantic patch that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier x; @@ -if (x) BUG(); +BUG_ON(x); @@ identifier x; @@ -if (!x) BUG(); +BUG_ON(!x); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22iscsi-target: Fix leak on failure in iscsi_copy_param_list()Jesper Juhl
We leak memory if the allocations for 'new_param->name' or 'new_param->value' fail in iscsi_target_parameters.c::iscsi_copy_param_list() We also do a lot of variable assignments that are completely pointless if the allocations fail. So, let's move the allocations before the assignments and also make sure that we free whatever was allocated to one if the allocation fail. There's also some small CodingStyle fixups in there (curly braces on both branches of if statement, only one variable per line) since I was in the area anyway. And finally, error messages in the function are put on a single line for easy grep'abillity. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Use ERR_CAST inlined functionThomas Meyer
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...)) The semantic patch that makes this output is available in scripts/coccinelle/api/err_cast.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/ Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2011-08-22target: Make standard INQUIRY return 'not connected' for tpg_virt_lun0Nicholas Bellinger
This patch changes target_emulate_inquiry_std() to set the 'not connected' (0x35) bit in standard INQUIRY response data when we are processing a request to a virtual LUN=0 mapping from struct se_device *g_lun0_dev that have been setup for us in transport_lookup_cmd_lun(). This addresses an issue where qla2xxx FC clients need to be able to create demo-mode I_T FC Nexuses by default, but should not be exposing the default set of TPG LUNs to all FC clients. This includes adding an new optional target_core_fabric_ops->tpg_check_demo_mode_login_only() caller to allow demo_mode nexuses to skip the old default of bulding a demo-mode MappedLUNs list via core_tpg_add_node_to_devs(). (roland: Add missing tpg_check_demo_mode_login_only check in core_dev_add_lun) Reported-by: Roland Dreier <roland@purestorage.com> Cc: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
2011-08-22Linux 3.1-rc3v3.1-rc3Linus Torvalds
2011-08-22net: Documentation: RFC 2553bis is now RFC 3493Geoffrey Thomas
Signed-off-by: Geoffrey Thomas <geofft@mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-22Merge branch 'perf-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: perf tools: Add group event scheduling option to perf record/stat MAINTAINERS: Fix list of perf events source files perf tools: Fix build against newer glibc perf tools: Fix error handling of unknown events perf evlist: Fix missing event name init for default event perf list: Fix exit value
2011-08-22Merge branch 'stable/bug.fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen * 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/tracing: Fix tracing config option properly xen: Do not enable PV IPIs when vector callback not present xen/x86: replace order-based range checking of M2P table by linear one xen: xen-selfballoon.c needs more header files
2011-08-22bcma: add uevent to the bus, to autoload driversDavid Woodhouse
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC addressSenthil Balasubramanian
Due to some recent optimization done in the way the mac address bytes are written into the OTP memory, some AR9485 chipsets were forced to use the first byte from the eeprom template and the remaining bytes are read from OTP. AR9485 happens to use generic eeprom template which has 0x1 as the first byte causes issues in bringing up the card. So fixed the eeprom template accordingly to address the issue. Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22rt2x00: do not drop usb dev reference counter on suspendStanislaw Gruszka
When hibernating ->resume may not be called by usb core, but disconnect and probe instead, so we do not increase the counter after decreasing it in ->supend. As a result we free memory early, and get crash when unplugging usb dongle. BUG: unable to handle kernel paging request at 6b6b6b9f IP: [<c06909b0>] driver_sysfs_remove+0x10/0x30 *pdpt = 0000000034f21001 *pde = 0000000000000000 Pid: 20, comm: khubd Not tainted 3.1.0-rc1-wl+ #20 LENOVO 6369CTO/6369CTO EIP: 0060:[<c06909b0>] EFLAGS: 00010202 CPU: 1 EIP is at driver_sysfs_remove+0x10/0x30 EAX: 6b6b6b6b EBX: f52bba34 ECX: 00000000 EDX: 6b6b6b6b ESI: 6b6b6b6b EDI: c0a0ea20 EBP: f61c9e68 ESP: f61c9e64 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process khubd (pid: 20, ti=f61c8000 task=f6138270 task.ti=f61c8000) Call Trace: [<c06909ef>] __device_release_driver+0x1f/0xa0 [<c0690b20>] device_release_driver+0x20/0x40 [<c068fd64>] bus_remove_device+0x84/0xe0 [<c068e12a>] ? device_remove_attrs+0x2a/0x80 [<c068e267>] device_del+0xe7/0x170 [<c06d93d4>] usb_disconnect+0xd4/0x180 [<c06d9d61>] hub_thread+0x691/0x1600 [<c0473260>] ? wake_up_bit+0x30/0x30 [<c0442a39>] ? complete+0x49/0x60 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0 [<c0472eb4>] kthread+0x74/0x80 [<c0472e40>] ? kthread_worker_fn+0x150/0x150 [<c0809b3e>] kernel_thread_helper+0x6/0x10 Cc: stable@kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22mac80211: fix suspend/resume races with unregister hwStanislaw Gruszka
Do not call ->suspend, ->resume methods after we unregister wiphy. Also delete sta_clanup timer after we finish wiphy unregister to avoid this: WARNING: at lib/debugobjects.c:262 debug_print_object+0x85/0xa0() Hardware name: 6369CTO ODEBUG: free active (active state 0) object type: timer_list hint: sta_info_cleanup+0x0/0x180 [mac80211] Modules linked in: aes_i586 aes_generic fuse bridge stp llc autofs4 sunrpc cpufreq_ondemand acpi_cpufreq mperf ext2 dm_mod uinput thinkpad_acpi hwmon sg arc4 rt2800usb rt2800lib crc_ccitt rt2x00usb rt2x00lib mac80211 cfg80211 i2c_i801 iTCO_wdt iTCO_vendor_support e1000e ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom yenta_socket ahci libahci pata_acpi ata_generic ata_piix i915 drm_kms_helper drm i2c_algo_bit video [last unloaded: microcode] Pid: 5663, comm: pm-hibernate Not tainted 3.1.0-rc1-wl+ #19 Call Trace: [<c0454cfd>] warn_slowpath_common+0x6d/0xa0 [<c05e05e5>] ? debug_print_object+0x85/0xa0 [<c05e05e5>] ? debug_print_object+0x85/0xa0 [<c0454dae>] warn_slowpath_fmt+0x2e/0x30 [<c05e05e5>] debug_print_object+0x85/0xa0 [<f8a808e0>] ? sta_info_alloc+0x1a0/0x1a0 [mac80211] [<c05e0bd2>] debug_check_no_obj_freed+0xe2/0x180 [<c051175b>] kfree+0x8b/0x150 [<f8a126ae>] cfg80211_dev_free+0x7e/0x90 [cfg80211] [<f8a13afd>] wiphy_dev_release+0xd/0x10 [cfg80211] [<c068d959>] device_release+0x19/0x80 [<c05d06ba>] kobject_release+0x7a/0x1c0 [<c07646a8>] ? rtnl_unlock+0x8/0x10 [<f8a13adb>] ? wiphy_resume+0x6b/0x80 [cfg80211] [<c05d0640>] ? kobject_del+0x30/0x30 [<c05d1a6d>] kref_put+0x2d/0x60 [<c05d056d>] kobject_put+0x1d/0x50 [<c08015f4>] ? mutex_lock+0x14/0x40 [<c068d60f>] put_device+0xf/0x20 [<c069716a>] dpm_resume+0xca/0x160 [<c04912bd>] hibernation_snapshot+0xcd/0x260 [<c04903df>] ? freeze_processes+0x3f/0x90 [<c049151b>] hibernate+0xcb/0x1e0 [<c048fdc0>] ? pm_async_store+0x40/0x40 [<c048fe60>] state_store+0xa0/0xb0 [<c048fdc0>] ? pm_async_store+0x40/0x40 [<c05d0200>] kobj_attr_store+0x20/0x30 [<c0575ea4>] sysfs_write_file+0x94/0xf0 [<c051e26a>] vfs_write+0x9a/0x160 [<c0575e10>] ? sysfs_open_file+0x200/0x200 [<c051e3fd>] sys_write+0x3d/0x70 [<c080959f>] sysenter_do_call+0x12/0x28 Cc: stable@kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22Merge branch 'master' of ↵John W. Linville
master.kernel.org:/pub/scm/linux/kernel/git/padovan/bluetooth
2011-08-22Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
generated by cgit (git 2.34.1) at 2025-09-13 05:20:22 +0000