| Age | Commit message (Collapse) | Author |
|---|
|
Always use ata_sff_data_xfer32() in ata_sff_data_xfer_noirq()
so the latter can be also used for host controllers supporting
32-bit PIO operations.
It is a completely safe thing to do because if 32-bit PIO is
not supported or enabled ata_sff_data_xfer32() will fallback
to a standard method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (aec62xx) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (sl82c105) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (pdc202xx_new) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add controller type field to struct legacy_data and then use it
to merge together all ->set_piomode methods for QDI controllers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
QDI65x0 controllers are fully supported by pata_legacy driver
so remove no longer needed pata_qdi driver.
Leave PATA_QDI config option for compatibility reasons and teach
pata_legacy to preserve the old behavior of pata_qdi driver.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Rename 'idetm_port' and 'idetm_data' variables to 'master_port'
and 'master_data' respectively to match register naming used in
it8213_set_dmamode() and in ata_piix.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes IDE -> libata regression.
IDE's it8213 host driver has been supporting those modes
(per official documentation) since the initial driver's merge
on Feb 7 2007 (commit 9c6712c0 "ide: add it8213 IDE driver").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This is similar change as commit 60c3be3 ("ata_piix: parallel scanning
on PATA needs an extra locking") for ata_piix host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* Fix via_init_one() to enable clock on 66 MHz devices
(bug introduced in commit 460f531 "pata_via: store UDMA masks
in via_isa_bridges table").
* Factor out common code from via_[re]init_one() to via_fixup().
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
XFER_SW_DMA_0 mode should be excluded from the extended cycle timing
computations.
Acked-by: Alan Cox <alan@linux.intel.com>
Noticed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use standard ata_cable_80wire() method for the cable detection,
as a bonus this allows us to use the default ->prereset method.
Acked-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The suspend()/resume() methods already get the right 'struct device' to get the
driver data from -- there's no need to get to the 'struct platform_device' that
contains that 'struct device' just to call dev_get_drvdata()...
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes PCI access before PCI resources are allocated.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Factor out common code from serverworks_[re]init_one() to
serverworks_fixup().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Merge identical cable routines for Dell and Sun systems into
common oem_cable() one.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Cosmetic fix but thanks to it pata_ali's DMI table now matches
alim15x3's one.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Core libata code takes care of it nowadays.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Factor out common code from cmd64x_[re]init_one() to cmd64x_fixup().
Remove stale comment and fix a minor CodingStyle issue while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Factor out code for finding the register programming information
from hpt366_set_mode() to hpt36x_find_mode().
This makes pata_hpt366 driver more similar to pata_{37x,3x2n} ones.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* Unify ->prereset methods for ATP850 and ATP86x[R] chipsets.
* Fix ->prereset documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
pata_at91_probe() forgets to call clk_put() iff ata_host_activate() fails...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Turn both helpers (which are used only during LLDs initialization
time and thus are not performance sensitive) into wrappers around
the new ata_pci_init_one() function, this cuts 20 LOC and saves
~1.1k of the output code size (x86-64):
text data bss dec hex filename
21392 0 19 21411 53a3 drivers/ata/libata-sff.o.before
20256 0 19 20275 4f33 drivers/ata/libata-sff.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
.. and also a module description while at it.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Current ore_check_io API receives a residual
pointer, to report partial IO. But it is actually
not used, because in a multiple devices IO there
is never a linearity in the IO failure.
On the other hand if every failing device is reported
through a received callback measures can be taken to
handle only failed devices. One at a time.
This will also be needed by the objects-layout-driver
for it's error reporting facility.
Exofs is not currently using the new information and
keeps the old behaviour of failing the complete IO in
case of an error. (No partial completion)
TODO: Use an ore_check_io callback to set_page_error only
the failing pages. And re-dirty write pages.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
All users of the ore will need to check if current code
supports the given layout. For example RAID5/6 is not
currently supported.
So move all the checks from exofs/super.c to a new
ore_verify_layout() to be used by ore users.
Note that any new layout should be passed through the
ore_verify_layout() because the ore engine will prepare
and verify some internal members of ore_layout, and
assumes it's called.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
Users like the objlayout-driver would like to only pass
a partial device table that covers the IO in question.
For example exofs divides the file into raid-group-sized
chunks and only serves group_width number of devices at
a time.
The partiality is communicated by setting
ore_componets->first_dev and the array covers all logical
devices from oc->first_dev upto (oc->first_dev + oc->numdevs)
The ore_comp_dev() API receives a logical device index
and returns the actual present device in the table.
An out-of-range dev_index will BUG.
Logical device index is the theoretical device index as if
all the devices of a file are present. .i.e:
total_devs = group_width * mirror_p1 * group_count
0 <= dev_index < total_devs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
Memory conditions and max_bio constraints might cause us to
not comply to the full length of the requested IO. Instead of
failing the complete IO we can issue a shorter read/write and
report how much was actually executed in the ios->length
member.
All users must check ios->length at IO_done or upon return of
ore_read/write and re-issue the reminder of the bytes. Because
other wise there is no error returned like before.
This is part of the effort to support the pnfs-obj layout driver.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
If at read/write_done the actual IO was shorter then requested,
reported in returned ios->length. It is not an error. The reminder
of the pages should just be unlocked but not marked uptodate or
end_page_writeback. They will be re issued later by the VFS.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
Move the check and preparation of the ios->kern_buff case to
later inside _write_mirror().
Since read was never used with ios->kern_buff its support is removed
instead of fixed.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
Now that each ore_io_state covers only a single raid group.
A single striping_info math is needed. Embed one inside
ore_io_state to cache the calculation results and eliminate
an extra call.
Also the outer _prepare_for_striping is removed since it does nothing.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
Usually a single IO is confined to one group of devices
(group_width) and at the boundary of a raid group it can
spill into a second group. Current code would allocate a
full device_table size array at each io_state so it can
comply to requests that span two groups. Needless to say
that is very wasteful, specially when device_table count
can get very large (hundreds even thousands), while a
group_width is usually 8 or 10.
* Change ore API to trim on IO that spans two raid groups.
The user passes offset+length to ore_get_rw_state, the
ore might trim on that length if spanning a group boundary.
The user must check ios->length or ios->nrpages to see
how much IO will be preformed. It is the responsibility
of the user to re-issue the reminder of the IO.
* Modify exofs To copy spilled pages on to the next IO.
This means one last kick is needed after all coalescing
of pages is done.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Constify tables in sil680_set_[pio,dma]mode().
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix documentation for sil680_sel[reg,dev]() and sil680_set_[pio,dma]mode().
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The balloon driver's "current_pages" is very different from
totalram_pages. Self-ballooning needs to be driven by
the latter. Also, Committed_AS doesn't account for pages
used by the kernel so:
1) Add totalreserve_pages to Committed_AS for the normal target.
2) Enforce a floor for when there are little or no user-space threads
using memory (e.g. single-user mode) to avoid OOMs. The floor
function includes a "min_usable_mb" tuneable in case we discover
later that the floor function is still too aggressive in some
workloads, though likely it will not be needed.
Changes since version 4:
- change floor calculation so that it is not as aggressive; this version
uses a piecewise linear function similar to minimum_target in the 2.6.18
balloon driver, but modified to add to totalreserve_pages instead of
subtract from max_pfn, the 2.6.18 version causes OOMs on recent kernels
because the kernel has expanded over time
- change safety_margin to min_usable_mb and comment on its use
- since committed_as does NOT include kernel space (and other reserved
pages), totalreserve_pages is now added to committed_as. The result is
less aggressive self-ballooning, but theoretically more appropriate.
Changes since version 3:
- missing include causes compile problem when CONFIG_FRONTSWAP is disabled
- add comments after includes
Changes since version 2:
- missing include causes compile problem only on 32-bit
Changes since version 1:
- tuneable safety margin added
[v5: avi.miller@oracle.com: still too aggressive, seeing some OOMs]
[v4: konrad.wilk@oracle.com: fix compile when CONFIG_FRONTSWAP is disabled]
[v3: guru.anbalagane@oracle.com: fix 32-bit compile]
[v2: konrad.wilk@oracle.com: make safety margin tuneable]
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
[v1: Altered description and added an extra include]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Devices supporting Process Address Space Identifiers
(PASIDs) can use an IOMMU to access multiple IO address
spaces at the same time. A PCIe device indicates support for
this feature by implementing the PASID capability. This
patch adds support for the capability to the Linux kernel.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Implement the necessary functions to handle PRI capabilities
on PCIe devices. With PRI devices behind an IOMMU can signal
page fault conditions to software and recover from such
faults.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch makes the ATS functions usable for modules.
They will be used by a module implementing some advanced
AMD IOMMU features.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
ATS does not depend on IOV support, so move the code into
its own file. This file will also include support for the
PRI and PASID capabilities later.
Also give ATS its own Kconfig variable to allow selecting it
without IOV support.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The result returned by acpi_dev_run_wake() is always either -EINVAL
or -ENODEV, while obviously it should return 0 on success. The
problem is that the leftover error variable, that's not really used
in the function, is initialized with -ENODEV and then returned
without modification.
To fix this issue remove the error variable from acpi_dev_run_wake()
and make the function return 0 on success as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
I originally submitted a patch to workaround this by pushing all Ejection
Requests and Device Checks onto the kacpi_hotplug queue.
http://marc.info/?l=linux-acpi&m=131678270930105&w=2
The patch is still insufficient in that Bus Checks also need to be added.
Rather than add all events, including non-PCI-hotplug events, to the
hotplug queue, mjg suggested that a better approach would be to modify
the acpiphp driver so only acpiphp events would be added to the
kacpi_hotplug queue.
It's a longer patch, but at least we maintain the benefit of having separate
queues in ACPI. This, of course, is still only a workaround the problem.
As Bjorn and mjg pointed out, we have to refactor a lot of this code to do
the right thing but at this point it is a better to have this code working.
The acpi core places all events on the kacpi_notify queue. When the acpiphp
driver is loaded and a PCI card with a PCI-to-PCI bridge is removed the
following call sequence occurs:
cleanup_p2p_bridge()
-> cleanup_bridge()
-> acpi_remove_notify_handler()
-> acpi_os_wait_events_complete()
-> flush_workqueue(kacpi_notify_wq)
which is the queue we are currently executing on and the process will hang.
Move all hotplug acpiphp events onto the kacpi_hotplug workqueue. In
handle_hotplug_event_bridge() and handle_hotplug_event_func() we can simply
push the rest of the work onto the kacpi_hotplug queue and then avoid the
deadlock.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: mjg@redhat.com
Cc: bhelgaas@google.com
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The land of PCI power management is a land of sorrow and ugliness,
especially in the area of signaling events by devices. There are
devices that set their PME Status bits, but don't really bother
to send a PME message or assert PME#. There are hardware vendors
who don't connect PME# lines to the system core logic (they know
who they are). There are PCI Express Root Ports that don't bother
to trigger interrupts when they receive PME messages from the devices
below. There are ACPI BIOSes that forget to provide _PRW methods for
devices capable of signaling wakeup. Finally, there are BIOSes that
do provide _PRW methods for such devices, but then don't bother to
call Notify() for those devices from the corresponding _Lxx/_Exx
GPE-handling methods. In all of these cases the kernel doesn't have
a chance to receive a proper notification that it should wake up a
device, so devices stay in low-power states forever. Worse yet, in
some cases they continuously send PME Messages that are silently
ignored, because the kernel simply doesn't know that it should clear
the device's PME Status bit.
This problem was first observed for "parallel" (non-Express) PCI
devices on add-on cards and Matthew Garrett addressed it by adding
code that polls PME Status bits of such devices, if they are enabled
to signal PME, to the kernel. Recently, however, it has turned out
that PCI Express devices are also affected by this issue and that it
is not limited to add-on devices, so it seems necessary to extend
the PME polling to all PCI devices, including PCI Express and planar
ones. Still, it would be wasteful to poll the PME Status bits of
devices that are known to receive proper PME notifications, so make
the kernel (1) poll the PME Status bits of all PCI and PCIe devices
enabled to signal PME and (2) disable the PME Status polling for
devices for which correct PME notifications are received.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the
base frequency. However, the quirk first checks to see if the proprietary
MMC controller is disabled, and returns if so. On some devices, such as the
Lenovo X220, the MMC controller is already disabled by firmware it seems,
but the frequency change is still needed so sdhci-pci can talk to the cards.
Since the MMC controller is disabled, the frequency fixup was never being run
on these machines.
This moves the e823 check above the MMC controller check so that it always
gets run.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The "powernv" platform of the powerpc architecture needs to assign PCI
resources using a specific algorithm to fit some HW constraints of
the IBM "IODA" architecture (related to the ability to create error
handling domains that encompass specific segments of MMIO space).
For doing so, it wants to call pci_setup_bridge() from architecture
specific resource management in order to configure bridges after all
resources have been assigned. So make it non-static.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
