| Age | Commit message (Collapse) | Author |
|---|
|
New ICs have hardware mailbox to deliver bt information instead of doing
it by driver itself, so remove them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
set coex table fine tune, for register settings
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The larger the bt a2dp bit pool is, the more time bt needs to receive
them. If we do not adjust the wifi duration, the voice quality will be
low. Hence we reduce the time that wifi holds, to improve the a2dp
service.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
modify h2c parameter so that the rate suffers less penalty from retry
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If there are too many CRC error packets, it means the wifi is operating
under low quality circumstances. If so, we need to reallocate the
resources of wifi and bt
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
if the bt is slave, it may receive packet at any time, so we
need to mark them as high priority packets to avoid packet loss.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For wifi and bt coexistence, if the aggregation size of wifi is too
large, the transmission time of the aggregated packet could be too long
and the bt packets might "cut off" the wifi packet. We need to reduce
the aggregation size to improve wifi performance.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix a number of checkpatch.pl warnings. In addition, some variable and
function names are shortened, and/or renamed to be more consistent.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
A number of functions in the Bluetooth Coexistence routines are not used,
and can be removed.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In mwifiex,IEs such as supported channels, supported operating classes
20/40 BSS COexistence are missing and also extra QOS capabilities IE
is added during TDLS discovery response, TDLS setup request and
TDLS setupresponse.
This patch adds require IEs and also removes extra IE.
Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
trivial fix to spelling mistakes in wl1271_warning error message, change
iligal to invalid and opperation to operation.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When resetting the device, we take a synchronous firmware-loading code
path, which borrows a lot from the asynchronous path used at probe time.
We don't catch errors correctly though, which means that in the PCIe
driver, we may try to dereference the 'adapter' struct after
mwifiex_fw_dpc() has freed it. See this (erronous) print in
mwifiex_pcie_reset_notify():
mwifiex_dbg(adapter, INFO, "%s, successful\n", __func__);
Let's instead refactor the synchronous (or "!req_fw_nowait") path so
that we propagate errors and handle them properly.
This fixes a use-after-free issue in the PCIe driver, as well as a
misleading debug message ("successful"). It looks like the SDIO driver
doesn't have these problems, since it doesn't do anything after
mwifiex_reinit_sw().
Fixes: 4c5dae59d2e9 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If we fail to reinit the FW when resetting the device (in the
synchronous version of mwifiex_init_hw_fw() -> mwifiex_fw_dpc()),
mwifiex_fw_dpc() will tear down the interface and free up the adapter.
But we don't actually check for all failure cases of mwifiex_fw_dpc(),
so some of them fall through and dereference adapter->fw_done with a
freed adapter, causing a use-after-free bug.
In any case, mwifiex_fw_dpc() will always signal FW completion -- in the
error OR success case -- so at best, this was repeat work. Let's not do
it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In brcmf_pno_start_sched_scan() a local variable is declared and
assigned for struct brcmu_d11inf. However, there is no other reference
to it so it is unnecessary.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In brcmf_pcie_suspend() we inform the firmware on the device that
it will enter in D3 state. Before this is done we already bring down
the bus state. However, When entering D3 fails we abort the suspend
and the bus state need to be restored.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
To support network namespace the driver must assure all created
network interfaces are in the same namespace as the wiphy instance
and flag the support using WIPHY_FLAG_NETNS_OK.
Verified using two terminals:
Terminal 1 Terminal 2
-------------------------- ---------------------------------
# ip netns add brcm-wifi # iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x1
# ip netns exec brcm-wifi bash
# iw dev
# echo $$
20337 # iw phy0 set netns 20337
# iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x2
# iw phy0 interface add wl3.ap type __ap
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x3
Interface wlan3
ifindex 11
wdev 0x2
# iw dev
# iw phy0 set netns 1
# iw dev
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x5
Interface wlan3
ifindex 11
wdev 0x4
Note:
increasing wdev identifier above indicates issue in
cfg80211 which is addressed separately.
Tested-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move brcmf_fws_deinit into brcmf_proto_bcdc_detach since it is a bcdc
exclusive feature.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Create a new protocol layer interface brcmf_proto_init_cb for protocol
layer to finish initialzation after core module components(fweh and
etc.) are initialized.
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Chip goes into low power state when this feature is enabled.
This was already enabled for SDIO and PCIe interface based
chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
USB firmware added support for sending command response/event through
interrupt endpoint, to enhance RX throughput. Added corresponding changes
required to support this feature. This change takes care of backward
compatibility with older firmware.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For quite some time now brcmfmac supports 802.11ac chipsets and it's
not limited to embedded devices only. There are even standalone PCIe
cards based on BCM43602 or BCM4366.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For SPI, we can get up to 32 additional bytes for response preamble.
The current overhead (2 bytes) may cause problems when we try to receive
a big response. Update it to 32 bytes.
Without this fix we could see a kernel BUG when we receive a big response
from the Chrome EC when is connected via SPI.
Signed-off-by: Vic Yang <victoryang@google.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo.collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Commit 4c6d9acce1f4 ("powerpc/mm: Add hooks for cxl") converted local
TLB invalidates to global if the cxl driver is active. This is necessary
because the CAPP snoops invalidations to forward them to the PSL on the
cxl adapter. However one path was forgotten. native_flush_hash_range()
still does local TLB invalidates, as found out the hard way recently.
This patch fixes it by following the same logic as previously: if the
cxl driver is active, the local TLB invalidates are 'upgraded' to
global.
Fixes: 4c6d9acce1f4 ("powerpc/mm: Add hooks for cxl")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When the kernel is compiled to use 64bit ABIv2 the _GLOBAL() macro does
not include a global entry point. A function's global entry point is
used when the function is called from a different TOC context and in the
kernel this typically means a call from a module into the vmlinux (or
vice-versa).
There are a few exported asm functions declared with _GLOBAL() and
calling them from a module will likely crash the kernel since any TOC
relative load will yield garbage.
flush_icache_range() and flush_dcache_range() are both exported to
modules, and use the TOC, so must use _GLOBAL_TOC().
Fixes: 721aeaa9fdf3 ("powerpc: Build little endian ppc64 kernel with ABIv2")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On UEFI systems, the PCI subsystem is enumerated by the firmware,
and if a graphical framebuffer is exposed via a PCI device, its base
address and size are exposed to the OS via the Graphics Output
Protocol (GOP).
On arm64 PCI systems, the entire PCI hierarchy is reconfigured from
scratch at boot. This may result in the GOP framebuffer address to
become stale, if the BAR covering the framebuffer is modified. This
will cause the framebuffer to become unresponsive, and may in some
cases result in unpredictable behavior if the range is reassigned to
another device.
So add a non-x86 quirk to the EFI fb driver to find the BAR associated
with the GOP base address, and claim the BAR resource so that the PCI
core will not move it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.7+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: leif.lindholm@linaro.org
Cc: linux-efi@vger.kernel.org
Cc: lorenzo.pieralisi@arm.com
Fixes: 9822504c1fa5 ("efifb: Enable the efi-framebuffer platform driver ...")
Link: http://lkml.kernel.org/r/20170404152744.26687-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The TRF7970A has configuration options for supporting hardware designs
with 1.8 Volt or 3.3 Volt IO. This commit adds a device tree option,
using a fixed regulator binding, for setting the io voltage to match
the hardware configuration. If no option is supplied it defaults to
3.3 volt configuration.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TRF7970A has configuration options to support hardware designs
which use a 27.12MHz clock. This commit adds a device tree option
'clock-frequency' to support configuring the this chip for default
13.56MHz clock or the optional 27.12MHz clock.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Put the right values from the original siginfo into the
userspace compat-siginfo.
This fixes the 32-bit MPX "tabletest" testcase on 64-bit kernels.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: a4455082dc6f0 ('x86/signals: Add missing signal_compat code for x86 features')
Link: http://lkml.kernel.org/r/1491322501-5054-1-git-send-email-joro@8bytes.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In some cases nfc_dbg() is useful. Add such macro to a header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
It looks like a typo to assign a return code to a variable which is not
used. Found due to a compiler warning:
net/nfc/netlink.c: In function ‘nfc_genl_activate_target’:
net/nfc/netlink.c:903:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
int rc;
^~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Another place in the code that unveils non-tested at all ACPI case.
Use unified device property API in meaningful way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since we got rid of platform data, the driver may use GPIO descriptor
directly.
Looking deeply to the use of the GPIO pin it looks like it should be
a fixed voltage regulator rather than custom GPIO handling. But this
is out of scope of the change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
I2C framework followed by IRQ framework does set interrupt polarity
correctly if it's properly specified in firmware (ACPI or DT).
Get rid of the redundant trick when requesting interrupt.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Legacy platform data must go away. We are on the safe side here since
there are no users of it in the kernel.
If anyone by any odd reason needs it the GPIO lookup tables and
built-in device properties at your service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
We return -ENODEV if ACPI provides a GPIO resource. Looks really wrong.
If it has even been tested?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since OF and ACPI case almost the same get rid of code duplication
by moving gpiod_get() calls directly to ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The error handling will be neat and short when using managed resources.
Convert the driver to use devm_request_threaded_irq().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since we got rid of platform data, the driver may use
GPIO descriptor directly.
This change fixes a potential issue of double freeing GPIOs in ACPI
case by converting to devm_gpiod_get().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Legacy platform data must go away. We are on the safe side here since
there are no users of it in the kernel.
If anyone by any odd reason needs it the GPIO lookup tables and
built-in device properties at your service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix output from checkpatch.pl like:
Symbolic permissions 'S_IRUSR' are not preferred.
Consider using octal permissions '0400'.
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate lin
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch helps to fix TPC stats to display the stats
properly. Here cosmetic change has been done to print the
TPC stats for all the cases 1.CDD 2.STBC 3.TXBF
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Remove obselete Copy Engine comments referring to the function
ath10k_ce_sendlist_send as this function was removed long time back
by the commit 2e761b5a5222 ("ath10k: remove ce_sendlist_send").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add an ath10k HTC debug message when insufficient tx credits
are available to send the WMI commands. This is very useful
in debugging issues like 'tx credit starvation' that could
possibly happen with multiclient setup with constant roaming
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It seems set_coverage_class_work is not cancelled anywhere,
though I could not find a crash/warning with this existing
design, its safer to cancel it during stop() and also before
restarting the hardware.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
If station advertises diffferent NSS capabilities in Rx_mcs set
of HT and VHT IEs in assoc req, the current NSS computation
logic configures the NSS support only based on Rx_mcs set of
HT capabilities in the driver. This is configuring the station
NSS capabilities incorreclty in the target.
For example, if station advertise Rx_mcs set as 2 spatial streams
in HT capabilities and 1 spatial streams in VHT capabilities in
assoc request, as per current logic we are calculating nss from
HT capabilities and the driver sets peer_num_spatial_streams as
2 for the station which is configured in VHT 1*1.
This patchs fix this issue by calculating the nss from VHT cap if
station supports vht.
Signed-off-by: Venkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce430657 ("ath9k_htc: Handle storage devices")
Cc: stable <stable@vger.kernel.org> # 2.6.39+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Move NAPI enable to 'ath10k_ahb_hif_start' from
'ath10k_ahb_hif_power_up'. This is to maintain the symmetry
of calling napi_enable() from ath10k_ahb_hif_start() so that it
matches with napi_disable() being called from ath10k_pci_hif_stop().
This change is based on the crash fix from Kalle for PCI interface in
commit 1427228d5869 ("ath10k: fix napi crash during rmmod when probe
firmware fails").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
