| Age | Commit message (Collapse) | Author |
|---|
|
When we get SN that is smaller than SSN of the aggregation,
we shouldn't apply any reordering on them.
Further more, HW NSSN will be zeroed, which can cause us
to make some invalid decisions.
Detect the situation and invalidate the BAID.
Fixes: b915c10174fb ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Change the value of TX_CMD_SEC_KEY_FROM_TABLE flag
in TX_CMD security flags to accommodate a FW API change.
Bump min API for 9000 series devices to 30 to keep the driver aligned
aligned the FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Seems like HW is reversing addr3 in the MAC header of de-aggregated
AMSDU. Reverse it back.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This flag is used for mac80211 reordering. As we do reordering
ourselves, turning it on is misleading and pointless.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Not only that this write is not needed (as FW does this
itself), on newer HW this register is write protected
so trying to write there will cause problems.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In TVQM firmware returns the value of the queue ID and code
should accept it.
The TX queue config API was changed. Move to new API.
This has to be done in parallel in mvm and pcie.
Do not move yet to 512 queues since there are some opens
with enabling it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In TVQM mode the TX responses were changed to include
queue number since legacy TX queue number retrieval cannot
be scaled up to 512 queues.
Support this change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In TVQM mode the queue ID is assigned after enablement.
Get rid of assuming pre-defined TX queue ID in functions
that will be used by TVQM allocation path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The "invalid" label was a bit ugly and unnecessary. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Change queue allocation to be dynamic. On transport init only
the command queue is being allocated. Other queues are allocated
on demand.
This is due to the huge amount of queues we will soon enable (512)
and as a preparation for TX Virtual Queue Manager feature (TVQM),
where firmware will assign the actual queue number on demand.
This includes also allocation of the byte count table per queue
and not as a contiguous chunk of memory.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This function is basically the same as gen1, except for clean
ups of old devices configuration that are never used in a000
configuration.
It will also help with refactoring rf_kill later on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In a000 transport we will allocate queues dynamically.
Right now queue are allocated as one big chunk of memory
and accessed as such.
The dynamic allocation of the queues will require accessing
the queues as pointers.
In order to keep simplicity of pre-a000 tx queues handling,
keep allocating and freeing the memory in the same style,
but move to access the queues in the various functions as
individual pointers.
Dynamic allocation for the a000 devices will be in a separate
patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
New transport will be used only by op modes that supports
buffer station offload - hence those will never be called.
Clean it up.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In a000 devices we have 16 bytes for the TFD index and 16 for the
queue, in order to support 512 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Code is basically the same, with a cleanups of old narrow host
command, ampg workarounds, some cosmetic stuff, and usage of
TFH functions when accessing TFD queues.
This enables also the cleanup of iwl_pcie_tfd_set_tb() since
now it won't be called anywhere in the a000 data path
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move to use the correct structure.
Remove code referring to old command.
Update DMA locations.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Cleanup code that is irrelevant for a000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
By moving all the code that depends on the new API
we avoid unnecessary indentation in the code.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Newer firmware versions will be able to handle all the
WMM-PS flows internally when we act as a GO. The firwmare
relies on the fact that the drivers puts frames for
different peers in different queues (DQA) to achieve this.
The driver will not be aware of the power state of the peers
anymore.
Tell the firmware about the WMM-PS parameters of earch peer
that connects to us so that it can know what are the
trigger-enabled ACs, the delivery-enableds ACs and the
Service Period length.
This API change is backward compatible since older firmware
versions will simply ignore the newly added values.
Since we don't support ieee80211 TSPECs for now, just copy
the trigger-enabled ACs to the delivery enabled ones.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There are several occasions where a scan of the same type is requested
concurrently, so logging every time this happens is just noisy and
unnecessary. Remove the logging for these cases.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is just a copy-paste in order to make changes tracking
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For a000 FW moved to 15 as management TID.
The change for us is fairly local - translate old TID to 15
when enabling and disabling a queue, and make sure to cover
it also on TX responses.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
a000 devices queue management is going to change significantly.
We will have 512 queues. Those queues will be assigned number
by the firmware and not by the driver.
In addition, due to SN offload having TX queue shared between TIDs
is impossible
Also, the ADD_STA command no longer updates queues status.
The only point of changing queue in the SCD queue config API.
From driver perspective we have here a new design:
Queue sharing and inactivity checks are disabled.
Once this is done, the only paths that call scd_queue_cfg command
are paths that alloc and release TX queues - which will make future
accommodation to queue number assignment by FW easier.
Since allocating 512 queues statically is not advisable, transport
will allocate the queue on demand, fill the command with DRAM data
and send it. This is reflected in the new transport API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In a000 devices the TX handling is different in a few ways:
* Queues are allocated dynamically
* DQA is enabled by default
* Driver shouldn't access TFH registers - ucode configures it
all in SCD_QUEUE_CFG command
Support all this in a new API with op mode, where op mode sends
the command, transport will allocate the queue dynamically, fill
in DMA properties, send the command to FW and get the ID back.
Current implementation only sets the new transport API and fills
the DMA properties.
Future patches will complete the other parts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support the new TX command API for a000 devices.
Command is a very slim version of current TX command.
Generalize iwl_mvm_tx_mpdu to get rid of TX command dependencies.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Dynamic SAR allows changing TX power limits at runtime to comply with
SAR regulations on multiple form factors (e.g. tablet vs. clamshell
mode). To support this, a new table was added to ACPI, which is
called Extended Wireless Regulatory Descriptor (EWRD). This table
allows OEMs to define different TX power profiles for each form-factor
or usage mode.
Read this new table and store it in our SAR profiles table, in
preparation for Dynamic SAR support.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For dynamic SAR, we will need to select the current profile from
different places. In preparation for that, spin the profile selection
code out of iwl_mvm_sar_init().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We are adding support for dynamic TX power tables for SAR (specific
absorption rate) compliance. Currently, we only support a single
(static) TX power table, which is read from ACPI, and use it
statically.
To prepare for more tables that can be switched dynamically, refactor
the SAR init flow to allow reusage and add the current static table as
a single entry in an array of tables.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Firmware isn't configuring multi RX queue hardware yet in
the self init mode.
Disable it for now until we have an API that enables it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
API will be the same regardless of FW compilation.
CDB related values will be filled in only for CDB.
Cahneg code and names accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
iwl_has_secure_boot() isn't getting called anywhere. Clean it up.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently aux & broadcast queues are added before calling add
station, which results with a SCD_QUEUE_CFG command sent with
a station id unknown yet to fw.
While this works for pre-a000 firmware, the a000 fw requires
the order to be reversed.
The reason the change is only for a000 devices and not for
previous devices is that we cannot reverse the order since
the tfd_queue_mask containing the aux queue will cause FW to
assert on adding a queue mask with a queue that is not enabled.
This is not a problem in a000 fw since the tfd_queue_mask was
removed from the add sta API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Addresses were changed for a000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Commit 7613c922315e308a ("backlight: pwm_bl: Move the checks for initial
power state to a separate function") not just moved some code, but made
slight changes in semantics.
If a gpiochip doesn't implement the optional .get_direction() callback,
gpiod_get_direction always returns -EINVAL, which is never equal to
GPIOF_DIR_IN, leading to the GPIO not being configured for output.
To avoid this, invert the test and check for not GPIOF_DIR_OUT instead,
like the original code did.
This restores the display on r8a7740/armadillo.
Fixes: 7613c922315e308a ("backlight: pwm_bl: Move the checks for initial power state to a separate function")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
Currently the snapshot trigger enables the probe and then allocates the
snapshot. If the probe triggers before the allocation, it could cause the
snapshot to fail and turn tracing off. It's best to allocate the snapshot
buffer first, and then enable the trigger. If something goes wrong in the
enabling of the trigger, the snapshot buffer is still allocated, but it can
also be freed by the user by writting zero into the snapshot buffer file.
Also add a check of the return status of alloc_snapshot().
Cc: stable@vger.kernel.org
Fixes: 77fd5c15e3 ("tracing: Add snapshot trigger to function probes")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
The window scale may be enlarged from 14 to 15 according to the itef
draft https://tools.ietf.org/html/draft-nishida-tcpm-maxwin-03.
Use the macro TCP_MAX_WSCALE to support it easily with TCP stack in
the future.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The commit ab8bc7ed864b9c4f1fcb00a22bbe4e0f66ce8003
("netfilter: remove nf_ct_is_untracked")
changed the line
if (ct && !nf_ct_is_untracked(ct) && nfct_nat(ct)) {
to
if (ct && nfct_nat(ct)) {
meanwhile, the commit 41390895e50bc4f28abe384c6b35ac27464a20ec
("netfilter: ipvs: don't check for presence of nat extension")
from ipvs-next had changed the same line to
if (ct && !nf_ct_is_untracked(ct) && (ct->status & IPS_NAT_MASK)) {
When ipvs-next got merged into nf-next, the merge resolution took
the first version, dropping the conversion of nfct_nat().
While this doesn't cause a problem at the moment, it will once we stop
adding the nat extension by default.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Only "cache" needs to use ulong (its used with set_bit()), missed can use
u16. Also add build-time assertion to ensure event bits fit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If insertion of a new conntrack fails because the table is full, the kernel
searches the next buckets of the hash slot where the new connection
was supposed to be inserted at for an entry that hasn't seen traffic
in reply direction (non-assured), if it finds one, that entry is
is dropped and the new connection entry is allocated.
Allow the conntrack gc worker to also remove *assured* conntracks if
resources are low.
Do this by querying the l4 tracker, e.g. tcp connections are now dropped
if they are no longer established (e.g. in finwait).
This could be refined further, e.g. by adding 'soft' established timeout
(i.e., a timeout that is only used once we get close to resource
exhaustion).
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
commit 223b02d923ecd7c84cf9780bb3686f455d279279
("netfilter: nf_conntrack: reserve two bytes for nf_ct_ext->len")
had to increase size of the extension offsets because total size of the
extensions had increased to a point where u8 did overflow.
3 years later we've managed to diet extensions a bit and we no longer
need u16. Furthermore we can now add a compile-time assertion for this
problem.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
get rid of the (now unused) nf_ct_ext_add_length define and also
rename the function to plain nf_ct_ext_add().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
No need to track this for inkernel helpers anymore as
NF_CT_HELPER_BUILD_BUG_ON checks do this now.
All inkernel helpers know what kind of structure they
stored in helper->data.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Userspace should not abuse the kernel to store large amounts of data,
reject requests larger than the private area can accommodate.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
add a 32 byte scratch area in the helper struct instead of relying
on variable sized helpers plus compile-time asserts to let us know
if 32 bytes aren't enough anymore.
Not having variable sized helpers will later allow to add BUILD_BUG_ON
for the total size of conntrack extensions -- the helper extension is
the only one that doesn't have a fixed size.
The (useless!) NF_CT_HELPER_BUILD_BUG_ON(0); are added so that in case
someone adds a new helper and copy-pastes from one that doesn't store
private data at least some indication that this macro should be used
somehow is there...
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
its definition is not needed in nf_conntrack.h.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
By default the kernel emits all ctnetlink events for a connection.
This allows to select the types of events to generate.
This can be used to e.g. only send DESTROY events but no NEW/UPDATE ones
and will work even if sysctl net.netfilter.nf_conntrack_events is set to 0.
This was already possible via iptables' CT target, but the nft version has
the advantage that it can also be used with already-established conntracks.
The added nf_ct_is_template() check isn't a bug fix as we only support
mark and labels (and unlike ecache the conntrack core doesn't copy those).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
As per latest regulatory update for India, channel 52, 56, 60, 64
is no longer restricted to DFS. Enabling DFS/no infra flags in driver
results in applying all DFS related restrictions (like doing CAC etc
before this channel moves to 'available state') for these channels
even though the country code is programmed as 'India' in he hardware,
fix this by relaxing the frequency range while applying RADAR flags
only if the country code is programmed to India. If the frequency range
needs to modified based on different country code, ath_is_radar_freq
can be extended/modified dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Introduce a debugfs option to manually override the noise floor,
ignoring the automatically tuned noise floor of the driver/hw.
In my tests with a AR9580 based module and a tx99 5 MHz interferer,
I could tune the noisefloor to -95 dBm or above to allow communication
again. The automatic noise floor calibration sometimes could adapt to
the situation as well, but not reliably and permanently.
I would consider this "feature" experimental and interesting for people
debugging the noise floor calibration or other effects of the hardware.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
