| Age | Commit message (Collapse) | Author |
|---|
|
When running a 32bit guest under a 64bit hypervisor, the ARMv8
architecture defines a mapping of the 32bit registers in the 64bit
space. This includes banked registers that are being demultiplexed
over the 64bit ones.
On exceptions caused by an operation involving a 32bit register, the
HW exposes the register number in the ESR_EL2 register. It was so
far understood that SW had to distinguish between AArch32 and AArch64
accesses (based on the current AArch32 mode and register number).
It turns out that I misinterpreted the ARM ARM, and the clue is in
D1.20.1: "For some exceptions, the exception syndrome given in the
ESR_ELx identifies one or more register numbers from the issued
instruction that generated the exception. Where the exception is
taken from an Exception level using AArch32 these register numbers
give the AArch64 view of the register."
Which means that the HW is already giving us the translated version,
and that we shouldn't try to interpret it at all (for example, doing
an MMIO operation from the IRQ mode using the LR register leads to
very unexpected behaviours).
The fix is thus not to perform a call to vcpu_reg32() at all from
vcpu_reg(), and use whatever register number is supplied directly.
The only case we need to find out about the mapping is when we
actively generate a register access, which only occurs when injecting
a fault in a guest.
Cc: stable@vger.kernel.org
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The open coded tests for checking whether a PTE maps a page as
uncached use a flawed '(pte_val(xxx) & CONST) != CONST' pattern,
which is not guaranteed to work since the type of a mapping is
not a set of mutually exclusive bits
For HYP mappings, the type is an index into the MAIR table (i.e, the
index itself does not contain any information whatsoever about the
type of the mapping), and for stage-2 mappings it is a bit field where
normal memory and device types are defined as follows:
#define MT_S2_NORMAL 0xf
#define MT_S2_DEVICE_nGnRE 0x1
I.e., masking *and* comparing with the latter matches on the former,
and we have been getting lucky merely because the S2 device mappings
also have the PTE_UXN bit set, or we would misidentify memory mappings
as device mappings.
Since the unmap_range() code path (which contains one instance of the
flawed test) is used both for HYP mappings and stage-2 mappings, and
considering the difference between the two, it is non-trivial to fix
this by rewriting the tests in place, as it would involve passing
down the type of mapping through all the functions.
However, since HYP mappings and stage-2 mappings both deal with host
physical addresses, we can simply check whether the mapping is backed
by memory that is managed by the host kernel, and only perform the
D-cache maintenance if this is the case.
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Per the Vybrid Reference Manual (section 3.8.6.1), dspi0 has 6 chip
select signals associated with it, while dspi1 has only 4.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We have a machine Dell XPS 13 with the codec alc256, after resume back
from S3, the headphone has noise when play sound.
Through comparing with the coeff vaule before and after S3, we found
restoring a coeff register will help remove noise.
BugLink: https://bugs.launchpad.net/bugs/1519168
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We had seen lots of reports of this kind issue, so add one
warnning in blk-merge, then it can be triggered easily and
avoid to depend on warning/bug from drivers.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit bdced438acd83a(block: setup bi_phys_segments after
splitting) introduces function of computing bio->bi_phys_segments
during bio splitting.
Unfortunately both bio->bi_seg_front_size and bio->bi_seg_back_size
arn't computed, so too many physical segments may be obtained
for one request since both the two are used to check if one segment
across two bios can be possible.
This patch fixes the issue by computing the two variables in
blk_bio_segment_split().
Fixes: bdced438acd83a(block: setup bi_phys_segments after splitting)
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Inside blk_bio_segment_split(), previous bvec pointer(bvprvp)
always points to the iterator local variable, which is obviously
wrong, so fix it by pointing to the local variable of 'bvprv'.
Fixes: 5014c311baa2b(block: fix bogus compiler warnings in blk-merge.c)
Cc: stable@kernel.org #4.3
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A truncated cb_compound request will cause the client to decode null or
data from a previous callback for nfs4.1 backchannel case, or uninitialized
data for the nfs4.0 case. This is because the path through
svc_process_common() advances the request's iov_base and decrements iov_len
without adjusting the overall xdr_buf's len field. That causes
xdr_init_decode() to set up the xdr_stream with an incorrect length in
nfs4_callback_compound().
Fixing this for the nfs4.1 backchannel case first requires setting the
correct iov_len and page_len based on the length of received data in the
same manner as the nfs4.0 case.
Then the request's xdr_buf length can be adjusted for both cases based upon
the remaining iov_len and page_len.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
If clp->cl_cb_ident is zero, then nfs_cb_idr_remove_locked() skips removing
it when the nfs_client is freed. A decoding or server bug can then find
and try to put that first nfs_client which would lead to a crash.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: d6870312659d ("nfs4client: convert to idr_alloc()")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
When LAYOUTGET gets NFS4ERR_DELAY, we currently will wait 15s before
retrying the call. That is a _very_ long time, so add a timeout value to
struct nfs4_layoutget and pass nfs4_async_handle_error a pointer to it.
This allows the RPC engine to use a sliding delay window, instead of a
15s delay.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Commit 1ca843a2d2 "nfs: Fix GETATTR bitmap verification" has check
the bitmap after decoding success, but decode_attr_fs_locations forgets
cleanup the FATTR4_WORD0_FS_LOCATIONS bits.
decode_getfattr_attrs always return -EIO when meeting FS_LOCATIONS now.
ls: cannot access /mnt/referal: Input/output error
ls: cannot access /mnt/replicas: Input/output error
total 32
drwxr-xr-x. 7 root root 8192 Nov 16 20:36 pnfs
??????????? ? ? ? ? ? referal
??????????? ? ? ? ? ? replicas
v2: clear the bit earlier
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
NFS v4.2 operations can work outside of pNFS, so dprintk() output
shouldn't be placed under NFSDBG_PNFS.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
The NFS CLONE_RANGE defintion was wrong and thus never worked. Fix this
by simply using the btrfs ioctl defintion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Originally CLONE didn't allow for intra-file clones, but we recently
updated the spec to support this feature which is also supported by
local Linux file systems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Without this for example 64-bit binaries on typical amd64 distributions
would not be able to use ioctls on NFS. For now this only affects clones.
Additionally ->compat_ioctl is defined even for non-compat builds, so
get rid of the pointless ifdef.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Currently we pass uninitialized stack garbage in the count parameter.
The value is usually large enought to clone whole files and thus let
simple tests pass, but it makes the tests for range clones very unhappy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
The following test program from Dmitry can cause softlockups or RCU
stalls as it copies 1GB from tmpfs into eventfd and we don't have any
scheduling point at that path in sendfile(2) implementation:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
Add cond_resched() into __splice_from_pipe() to fix the problem.
CC: Dmitry Vyukov <dvyukov@google.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Commit 296291cdd162 (mm: make sendfile(2) killable) fixed an issue where
sendfile(2) was doing a lot of tiny writes into a filesystem and thus
was unkillable for a long time. However sendfile(2) can be (mis)used to
issue lots of writes into arbitrary file descriptor such as evenfd or
similar special file descriptors which never hit the standard filesystem
write path and thus are still unkillable. E.g. the following example
from Dmitry burns CPU for ~16s on my test system without possibility to
be killed:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
There are actually quite a few tests for pending signals in sendfile
code however we data to write is always available none of them seems to
trigger. So fix the problem by adding a test for pending signal into
splice_from_pipe_next() also before the loop waiting for pipe buffers to
be available. This should fix all the lockup issues with sendfile of the
do-ton-of-tiny-writes nature.
CC: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The thing got broken back in 2002 - sysvfs does *not* have inline
symlinks; even short ones have bodies stored in the first block
of file. sysv_symlink() handles that correctly; unfortunately,
attempting to look an existing symlink up will end up confusing
them for inline symlinks, and interpret the block number containing
the body as the body itself.
Nobody has noticed until now, which says something about the level
of testing sysvfs gets ;-/
Cc: stable@vger.kernel.org # all of them, not that anyone cared
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP which
is valid for all IMX6 SoC's (despite the fact that the IMXSDLRM and
IMXSXRM do not document this - this has been proven via tests as well as
verified by Freescale FAE).
Instead of assuming a fixed 85C for passive cooling threshold and 105C for
critical use the thermal grade for these configurations.
We will set the critical to maxT - 5C and passive to maxT - 10C.
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
----
v3:
- rebase against linux-soc-thermal.git
- added ack's from Shawn and Jon
v2:
- remove check for IMX6Q and update comments: The OTP values have been tested
on IMX6SOLO, IMX6DUALLITE, and IMX6SX and Freescale FAE has shared data with
me that the OTP settings are the same and that the reference manuals will
reflect this in their next updates.
- set critical to max - 5C
- set passive to max - 10C
- display max temp in info
- do not allow passive to be set above critical
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
When the prototype for thermal_zone_bind_cooling_device
changed, the static inline wrapper function was left alone,
which in theory can cause build warnings:
I have seen this error in the past:
drivers/thermal/db8500_thermal.c: In function 'db8500_cdev_bind':
drivers/thermal/db8500_thermal.c:78:9: error: too many arguments to function 'thermal_zone_bind_cooling_device'
ret = thermal_zone_bind_cooling_device(thermal, i, cdev,
while this one no longer shows up, there is no doubt that
the prototype is still wrong, so let's just fix it anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6cd9e9f629f1 ("thermal: of: fix cooling device weights in device tree")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This just caused build errors:
warning: (QCOM_SPMI_TEMP_ALARM) selects REGMAP_SPMI which has unmet direct dependencies (SPMI)
drivers/built-in.o: In function `regmap_spmi_ext_gather_write':
:(.text+0x609b0): undefined reference to `spmi_ext_register_write'
:(.text+0x609f0): undefined reference to `spmi_ext_register_writel'
While it's generally a good idea to allow compile testing, in this
case, it just doesn't work, so reverting the patch that
introduced the compile-test variant seems the most appropriate
solution.
Note that SPMI also has a 'depends on ARCH_QCOM || COMPILE_TEST'
statement, so we should be able to enable SPMI on all architectures
for compile testing already.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cb7fb4d34202 ("thermal: qcom_spmi: allow compile test")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq driver if the SCPI clk driver is missing.
Fix this by making the SCPI cpufreq driver explicitly depend on the SCPI
clk driver.
Fixes: 8def31034d03 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
A rounding error was found in the calculation of limits->max_perf
in intel_pstate_set_policy(), which is used to calculate the max and min
pstate values in intel_pstate_get_min_max(). In that code,
limits->max_perf is truncated to 2 hex digits such that, for example,
0x169 was incorrectly calculated to 0x16 instead of 0x17. This resulted in
the pstate being set one level too low. This patch rounds the value of
limits->max_perf up instead of down so that the correct max pstate can
be reached.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
I have a Intel (6,63) processor with a "marketing" frequency (from
/proc/cpuinfo) of 2100MHz, and a max turbo frequency of 2600MHz. I
can execute
cpupower frequency-set -g powersave --min 1200MHz --max 2100MHz
and the max_freq_pct is set to 80. When adding load to the system I noticed
that the cpu frequency only reached 2000MHZ and not 2100MHz as expected.
This is because limits->max_policy_pct is calculated as 2100 * 100 /2600 = 80.7
and is rounded down to 80 when it should be rounded up to 81. This patch
adds a DIV_ROUND_UP() which will return the correct value.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Subsys interface's ->remove_dev() is called when the cpufreq driver is
unregistering or the CPU is getting physically removed. We keep removing
the cpuX/cpufreq link for all CPUs except the last one, which is a
mistake as all CPUs contain a link now.
Because of this, one CPU from each policy will still contain a link (to
an already removed policyX directory), after the cpufreq driver is
unregistered.
Fix that by removing the link first and then only see if the policy is
required to be freed. That will make sure that no links are left out.
Fixes: 96bdda61f58b ("cpufreq: create cpu/cpufreq/policyX directories")
Reported-and-tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The CPU policy struct indicates the co-ordination type
for all CPUs of a common freq domain. Initialize it
correctly using the CPU specific data gathered from
CPPC ACPI lib via acpi_get_psd_map().
The PSD object is optional, so the cpu->shared_type
can also be 0. So instead of assuming any value other
than SW_ANY(0xFD) is unsupported, explictly check
if shared_type is SW_ALL and then bail.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update consists of one minor documentation fix and a fix to an
existing test"
* tag 'linux-kselftest-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/seccomp: Get page size from sysconf
tools:testing/selftests: fix typo in futex/README
|
|
When establishing a thin device's discard limits we cannot rely on the
underlying thin-pool device's discard capabilities (which are inherited
from the thin-pool's underlying data device) given that DM thin devices
must provide discard support even when the thin-pool's underlying data
device doesn't support discards.
Users were exposed to this thin device discard limits regression if
their thin-pool's underlying data device does _not_ support discards.
This regression caused all upper-layers that called the
blkdev_issue_discard() interface to not be able to issue discards to
thin devices (because discard_granularity was 0). This regression
wasn't caught earlier because the device-mapper-test-suite's extensive
'thin-provisioning' discard tests are only ever performed against
thin-pool's with data devices that support discards.
Fix is to have thin_io_hints() test the pool's 'discard_enabled' feature
rather than inferring whether or not a thin device's discard support
should be enabled by looking at the thin-pool's discard_granularity.
Fixes: 216076705 ("dm thin: disable discard support for thin devices if pool's is disabled")
Reported-by: Mike Gerber <mike@sprachgewalt.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.1+
|
|
bootargs
Currently kernel crash randomly when K2L EVM is booted without
clk_ignore_unused in the bootargs. This workaround is not needed
on other K2 devices such as K2HK and K2E and with this fix, we can
remove the workaround altogether. netcp driver on K2L uses linked
ram on OSR (On chip Static RAM) and requires the clock to this peripheral
enabled for proper functioning. This is the reason for the kernel crash.
So add the clock node to fix this issue.
While at it, remove the workaround documentation as well.
With the fix applied, clk_summary dump shows the clock to OSR enabled.
cat /sys/kernel/debug/clk/clk_summary
------cut--------------
tcp3d-1 0 0 399360000 0 0
tcp3d-0 0 0 399360000 0 0
osr 1 1 399360000 0 0
fftc-0 0 0 399360000 0 0
-----cut----------------
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Configure linking RAM for both queue managers also in case
when only linking RAM 0 is specified in device tree.
Currently hwqueue driver configures linking RAM(s) to be used
cooperatively by the QMs (shared mode). Therefore if both
queue managers are used then both must be configured with
exactly the same linking RAM info (base address and size)
independent of the number of linking RAM(s) specified in the
device tree.
For proper operation only one linking RAM is required and in most
cases this can be internal one as long as it is able to handle
the number of descriptors used in the system.
Current driver code however skips configuration of second
queue manager if second linking RAM is not specified.
If the configuration for the QM2 is missing there will be
a crash when it tries to push/pop descriptors from its queues.
Signed-off-by: Michal Morawiec <michal.1.morawiec.ext@nokia.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
When firmware image for PDSP firmware is absent in the file system
the kernel boot with ramfs/nfs is stuck for 60 seconds being the
the default timeout. request_firmware_direct() is to take care of
such optional firmware loading and hence replace the call in the
driver with this API.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
This way the driver isn't limited in the dependency handling callback.
v2: remove extra check in amd_sched_entity_pop_job()
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
|
|
We only need to wait for jobs to be scheduled when
the dependency is from the same scheduler.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
|
|
Fixes STAR 9000953410: "perf callgraph profiling causing RCU stalls"
| perf record -g -c 15000 -e cycles /sbin/hackbench
|
| INFO: rcu_preempt self-detected stall on CPU
| 1: (1 GPs behind) idle=609/140000000000002/0 softirq=2914/2915 fqs=603
| Task dump for CPU 1:
in-kernel dwarf unwinder has a fast binary lookup and a fallback linear
search (which iterates thru each of ~11K entries) thus takes 2 orders of
magnitude longer (~3 million cycles vs. 2000). Routines written in hand
assembler lack dwarf info (as we don't support assembler CFI pseudo-ops
yet) fail the unwinder binary lookup, hit linear search, failing
nevertheless in the end.
However the linear search is pointless as binary lookup tables are created
from it in first place. It is impossible to have binary lookup fail while
succeed the linear search. It is pure waste of cycles thus removed by
this patch.
This manifested as RCU stalls / NMI watchdog splat when running
hackbench under perf with callgraph profiling. The triggering condition
was perf counter overflowing in routine lacking dwarf info (like memset)
leading to patheic 3 million cycle unwinder slow path and by the time it
returned new interrupts were already pending (Timer, IPI) and taken
rightaway. The original memset didn't make forward progress, system kept
accruing more interrupts and more unwinder delayes in a vicious feedback
loop, ultimately triggering the NMI diagnostic.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Currently we can hit a scenario where we'll tm_reclaim() twice. This
results in a TM bad thing exception because the second reclaim occurs
when not in suspend mode.
The scenario in which this can happen is the following. We attempt to
deliver a signal to userspace. To do this we need obtain the stack
pointer to write the signal context. To get this stack pointer we
must tm_reclaim() in case we need to use the checkpointed stack
pointer (see get_tm_stackpointer()). Normally we'd then return
directly to userspace to deliver the signal without going through
__switch_to().
Unfortunatley, if at this point we get an error (such as a bad
userspace stack pointer), we need to exit the process. The exit will
result in a __switch_to(). __switch_to() will attempt to save the
process state which results in another tm_reclaim(). This
tm_reclaim() now causes a TM Bad Thing exception as this state has
already been saved and the processor is no longer in TM suspend mode.
Whee!
This patch checks the state of the MSR to ensure we are TM suspended
before we attempt the tm_reclaim(). If we've already saved the state
away, we should no longer be in TM suspend mode. This has the
additional advantage of checking for a potential TM Bad Thing
exception.
Found using syscall fuzzer.
Fixes: fb09692e71f1 ("powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently we allow both the MSR T and S bits to be set by userspace on
a signal return. Unfortunately this is a reserved configuration and
will cause a TM Bad Thing exception if attempted (via rfid).
This patch checks for this case in both the 32 and 64 bit signals
code. If both T and S are set, we mark the context as invalid.
Found using a syscall fuzzer.
Fixes: 2b0a576d15e0 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
WDT_MODE value need to be or-ed with MODE_KEY when setting
watchdog mode. Add it to mtk_wdt_stop function, so that the
watchdog can be stopped (e.g. during suspend).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Modify watchdog/Kconfig file to support Layerscape platforms.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
If we need to restart the watchdog due to someone changing the timeout
interval, stop the watchdog before restarting it. Otherwise, the new
timeout doesn't seem to take.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
"t" is controlled by the user. If "t" is a very large integer then it
could lead to a negative "tmrval". We cap the upper bound of "tmrval"
but, in the current code, we allow negatives. This is a bug and it
causes a static checker warning. Let's make "tmrval" unsigned to avoid
this problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Silences sparse warning:
drivers/watchdog/pnx4008_wdt.c:83:25:
warning: symbol 'wdt_clk' was not declared. Should it be static?
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Tainted: G W 4.3.0-rc2+ #171
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (pnx4008_wdt_probe+0x78/0x11c)
[<>] (pnx4008_wdt_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (platform_wdt_driver_init+0x18/0x20)
[<>] (platform_wdt_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Fix issue from two patches overlapping causing a kernel oops
[ 3569.297449] Unable to handle kernel NULL pointer dereference at virtual address 00000088
[ 3569.306272] pgd = dc894000
[ 3569.309287] [00000088] *pgd=00000000
[ 3569.313104] Internal error: Oops: 5 [#1] SMP ARM
[ 3569.317986] Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_filter ebtable_nat ebtable_broute bridge stp llc ebtables ip6table_security ip6table_raw ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_filter ip6_tables iptable_security iptable_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle musb_dsps cppi41 musb_hdrc phy_am335x udc_core phy_generic phy_am335x_control omap_sham omap_aes omap_rng omap_hwspinlock omap_mailbox hwspinlock_core musb_am335x omap_wdt at24 8250_omap leds_gpio cpufreq_dt smsc davinci_mdio mmc_block ti_cpsw cpsw_common ptp pps_core cpsw_ale davinci_cpdma omap_hsmmc omap_dma mmc_core i2c_dev
[ 3569.386293] CPU: 0 PID: 1429 Comm: wdctl Not tainted 4.3.0-0.rc7.git0.1.fc24.armv7hl #1
[ 3569.394740] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 3569.401179] task: dbd11a00 ti: dbaac000 task.ti: dbaac000
[ 3569.406917] PC is at omap_wdt_get_timeleft+0xc/0x20 [omap_wdt]
[ 3569.413106] LR is at watchdog_ioctl+0x3cc/0x42c
[ 3569.417902] pc : [<bf0ab138>] lr : [<c0739c54>] psr: 600f0013
[ 3569.417902] sp : dbaadf18 ip : 00000003 fp : 7f5d3bbe
[ 3569.430014] r10: 00000000 r9 : 00000003 r8 : bef21ab8
[ 3569.435535] r7 : dbbc0f7c r6 : dbbc0f18 r5 : bef21ab8 r4 : 00000000
[ 3569.442427] r3 : 00000000 r2 : 00000000 r1 : 8004570a r0 : dbbc0f18
[ 3569.449323] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 3569.456858] Control: 10c5387d Table: 9c894019 DAC: 00000051
[ 3569.462927] Process wdctl (pid: 1429, stack limit = 0xdbaac220)
[ 3569.469179] Stack: (0xdbaadf18 to 0xdbaae000)
[ 3569.473790] df00: bef21ab8 dbf60e38
[ 3569.482441] df20: dc91b840 8004570a bef21ab8 c03988a4 dbaadf48 dc854000 00000000 dd313850
[ 3569.491092] df40: ddf033b8 0000570a dc91b80b dbaadf3c dbf60e38 00000020 c0df9250 c0df6c48
[ 3569.499741] df60: dc91b840 8004570a 00000000 dc91b840 dc91b840 8004570a bef21ab8 00000003
[ 3569.508389] df80: 00000000 c03989d4 bef21b74 7f5d3bad 00000003 00000036 c020fcc4 dbaac000
[ 3569.517037] dfa0: 00000000 c020fb00 bef21b74 7f5d3bad 00000003 8004570a bef21ab8 00000001
[ 3569.525685] dfc0: bef21b74 7f5d3bad 00000003 00000036 00000001 00000000 7f5e4eb0 7f5d3bbe
[ 3569.534334] dfe0: 7f5e4f10 bef21a3c 7f5d0a54 b6e97e0c a00f0010 00000003 00000000 00000000
[ 3569.543038] [<bf0ab138>] (omap_wdt_get_timeleft [omap_wdt]) from [<c0739c54>] (watchdog_ioctl+0x3cc/0x42c)
[ 3569.553266] [<c0739c54>] (watchdog_ioctl) from [<c03988a4>] (do_vfs_ioctl+0x5bc/0x698)
[ 3569.561648] [<c03988a4>] (do_vfs_ioctl) from [<c03989d4>] (SyS_ioctl+0x54/0x7c)
[ 3569.569400] [<c03989d4>] (SyS_ioctl) from [<c020fb00>] (ret_fast_syscall+0x0/0x3c)
[ 3569.577413] Code: e12fff1e e52de004 e8bd4000 e5903060 (e5933088)
[ 3569.584089] ---[ end trace cec3039bd3ae610a ]---
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
GPC irq domain is a child domain of GIC, now all of platform irqs
are inside GPC domain, during the module populate, all devices irq
should have correct type setting in GIC, however, there is no
.irq_set_type callback setting in GPC, so the irq_set_type will be
skipped and cause all irqs' type in /proc/interrupt are "edge" which
mismatch with irq type setting in dtb file. Since GPC has no irq
type setting, so just tell kernel to use irq_chip_set_type_parent.
Signed-off-by: Anson Huang <Anson.Huang@freescale.com>
Cc: <stable@vger.kernel.org> # 4.1+
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Something seems to have gone wrong during the merging of the device
tree changes with the following patch
"ARM: dts: add property for maximum ADC clock frequencies"
The property "fsl,adck-max-frequency" instead of being applied for
the ADC1 node got applied to the esdhc0 node. This patch fixes it.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Fixes: def0641e2f61 ("ARM: dts: add property for maximum ADC clock frequencies")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Both the pointer array and the pointed data have to be const when using
__initconst to be correct. This also fixes LTO builds that otherwise
fail with section mismatch errors.
Fixes: ec60d95b4fac ("ARM: shmobile: Basic r8a7793 SoC support")
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
|
