| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"Another followup fix for the procps genirq output formatting
regression caused by an optimization"
* tag 'irq-urgent-2025-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Remove leading space from irq_chip::irq_print_chip() callbacks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"Fix a dangling pointer bug in the futex code used by the uring code.
It isn't causing problems at the moment due to uring ABI limitations
leaving it essentially unused in current usages, but is a good idea to
fix nevertheless"
* tag 'locking-urgent-2025-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Pass in task to futex_queue()
|
|
Explicitly clear DEBUGCTL.LBR when a CPU is starting, prior to purging the
LBR MSRs themselves, as at least one system has been found to transfer
control to the kernel with LBRs enabled (it's unclear whether it's a BIOS
flaw or a CPU goof). Because the kernel preserves the original DEBUGCTL,
even when toggling LBRs, leaving DEBUGCTL.LBR as is results in running
with LBRs enabled at all times.
Closes: https://lore.kernel.org/all/c9d8269bff69f6359731d758e3b1135dedd7cc61.camel@redhat.com
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20250131010721.470503-1-seanjc@google.com
|
|
The EAX of the CPUID Leaf 023H enumerates the mask of valid sub-leaves.
To tell the availability of the sub-leaf 1 (enumerate the counter mask),
perf should check the bit 1 (0x2) of EAS, rather than bit 0 (0x1).
The error is not user-visible on bare metal. Because the sub-leaf 0 and
the sub-leaf 1 are always available. However, it may bring issues in a
virtualization environment when a VMM only enumerates the sub-leaf 0.
Introduce the cpuid35_e?x to replace the macros, which makes the
implementation style consistent.
Fixes: eb467aaac21e ("perf/x86/intel: Support Architectural PerfMon Extension leaf")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20250129154820.3755948-3-kan.liang@linux.intel.com
|
|
The PEBS-via-PT feature is exposed for the e-core of some hybrid
platforms, e.g., ADL and MTL. But it never works.
$ dmesg | grep PEBS
[ 1.793888] core: cpu_atom PMU driver: PEBS-via-PT
$ perf record -c 1000 -e '{intel_pt/branch=0/,
cpu_atom/cpu-cycles,aux-output/pp}' -C8
Error:
The sys_perf_event_open() syscall returned with 22 (Invalid argument)
for event (cpu_atom/cpu-cycles,aux-output/pp).
"dmesg | grep -i perf" may provide additional information.
The "PEBS-via-PT" is printed if the corresponding bit of per-PMU
capabilities is set. Since the feature is supported by the e-core HW,
perf sets the bit for e-core. However, for Intel PT, if a feature is not
supported on all CPUs, it is not supported at all. The PEBS-via-PT event
cannot be created successfully.
The PEBS-via-PT is no longer enumerated on the latest hybrid platform. It
will be deprecated on future platforms with Arch PEBS. Let's remove it
from the existing hybrid platforms.
Fixes: d9977c43bff8 ("perf/x86: Register hybrid PMUs")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250129154820.3755948-2-kan.liang@linux.intel.com
|
|
After the commit b4943b8bfc41 ("perf/x86/rapl: Add core energy counter
support for AMD CPUs"), the default "perf record"/"perf top" command is
broken in systems where there isn't a PMU registered for type
PERF_TYPE_RAW.
This is due to the change in order of error checks in rapl_pmu_event_init()
Due to which we return -EINVAL instead of -ENOENT, when we reach here from
the fallback loop in perf_init_event().
Move the "PMU and event type match" back to the beginning of the function
so that we return -ENOENT early on.
Closes: https://lore.kernel.org/all/uv7mz6vew2bzgre5jdpmwldxljp5djzmuiksqdcdwipfm4zm7w@ribobcretidk/
Fixes: b4943b8bfc41 ("perf/x86/rapl: Add core energy counter support for AMD CPUs")
Reported-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Dhananjay Ugwekar <dhananjay.ugwekar@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250129080513.30353-1-dhananjay.ugwekar@amd.com
|
|
Clarify that wake_up_q() does an atomic write to task->wake_q.next, after
which a concurrent __wake_q_add() can immediately overwrite
task->wake_q.next again.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250129-sched-wakeup-prettier-v1-1-2f51f5f663fa@google.com
|
|
The lld.ld borkage is fixed in the latest llvm release (?) but will
not be backported, meaning we're stuck with broken linker for a fair
while.
Lets not spam all clang build logs and move warning to verbose.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
|
Clang sometimes leaves dangling unused jump table entries which point to
the end of the function. Ignore them.
Closes: https://lore.kernel.org/20250113235835.vqgvb7cdspksy5dn@jpoimboe
Reported-by: Klaus Kusche <klaus.kusche@computerix.info>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/ee25c0b7e80113e950bd1d4c208b671d35774ff4.1736891751.git.jpoimboe@kernel.org
|
|
The code was restructured where the function graph notrace code, that
would not trace a function and all its children is done by setting a
NOTRACE flag when the function that is not to be traced is hit.
There's a TRACE_GRAPH_NOTRACE_BIT which defines the bit in the flags and a
TRACE_GRAPH_NOTRACE which is the mask with that bit set. But the
restructuring used TRACE_GRAPH_NOTRACE_BIT when it should have used
TRACE_GRAPH_NOTRACE.
For example:
# cd /sys/kernel/tracing
# echo set_track_prepare stack_trace_save > set_graph_notrace
# echo function_graph > current_tracer
# cat trace
[..]
0) | __slab_free() {
0) | free_to_partial_list() {
0) | arch_stack_walk() {
0) | __unwind_start() {
0) 0.501 us | get_stack_info();
Where a non filter trace looks like:
# echo > set_graph_notrace
# cat trace
0) | free_to_partial_list() {
0) | set_track_prepare() {
0) | stack_trace_save() {
0) | arch_stack_walk() {
0) | __unwind_start() {
Where the filter should look like:
# cat trace
0) | free_to_partial_list() {
0) | _raw_spin_lock_irqsave() {
0) 0.350 us | preempt_count_add();
0) 0.351 us | do_raw_spin_lock();
0) 2.440 us | }
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20250208001511.535be150@batman.local.home
Fixes: b84214890a9bc ("function_graph: Move graph notrace bit to shadow stack global var")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
be allocated
Fix NULL pointer check in rkcanfd_handle_rx_fifo_overflow_int() to
bail out if skb cannot be allocated.
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Cc: stable@vger.kernel.org
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Link: https://patch.msgid.link/20250208-fix-rockchip-canfd-v1-1-ec533c8a9895@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver assumed that es58x_dev->udev->serial could never be NULL.
While this is true on commercially available devices, an attacker
could spoof the device identity providing a NULL USB serial number.
That would trigger a NULL pointer dereference.
Add a check on es58x_dev->udev->serial before accessing it.
Reported-by: yan kang <kangyan91@outlook.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Closes: https://lore.kernel.org/linux-can/SY8P300MB0421E0013C0EBD2AA46BA709A1F42@SY8P300MB0421.AUSP300.PROD.OUTLOOK.COM/
Fixes: 9f06631c3f1f ("can: etas_es58x: export product information through devlink_ops::info_get()")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250204154859.9797-2-mailhol.vincent@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Runtime PM is enabled as one of the last steps of probe(), so all
earlier gotos to "exit_free_device" label were not correct and were
leading to unbalanced runtime PM disable depth.
Fixes: 6e2fe01dd6f9 ("can: c_can: move runtime PM enable/disable to c_can_platform")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250112-syscon-phandle-args-can-v1-1-314d9549906f@linaro.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If skb allocation fails, the pointer to struct can_frame is NULL. This
is actually handled everywhere inside ctucan_err_interrupt() except for
the only place.
Add the missed NULL check.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2dcb8e8782d8 ("can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250114152138.139580-1-pchelkin@ispras.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
length zero
The J1939 standard requires the transmission of messages of length 0.
For example proprietary messages are specified with a data length of 0
to 1785. The transmission of such messages is not possible. Sending
results in no error being returned but no corresponding can frame
being generated.
Enable the transmission of zero length J1939 messages. In order to
facilitate this two changes are necessary:
1) If the transmission of a new message is requested from user space
the message is segmented in j1939_sk_send_loop(). Let the segmentation
take into account zero length messages, do not terminate immediately,
queue the corresponding skb.
2) j1939_session_skb_get_by_offset() selects the next skb to transmit
for a session. Take into account that there might be zero length skbs
in the queue.
Signed-off-by: Alexander Hölzl <alexander.hoelzl@gmx.net>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250205174651.103238-1-alexander.hoelzl@gmx.net
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Cc: stable@vger.kernel.org
[mkl: commit message rephrased]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In the current struct sockaddr_can tp is member of can_addr. tp is not
member of struct sockaddr_can.
Signed-off-by: Reyders Morales <reyders1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20250203224720.42530-1-reyders1@gmail.com
Fixes: 67711e04254c ("Documentation: networking: document ISO 15765-2")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
-Wenum-enum-conversion was strengthened in clang-19 to warn for C, which
caused the kernel to move it to W=1 in commit 75b5ab134bb5 ("kbuild:
Move -Wenum-{compare-conditional,enum-conversion} into W=1") because
there were numerous instances that would break builds with -Werror.
Unfortunately, this is not a full solution, as more and more developers,
subsystems, and distributors are building with W=1 as well, so they
continue to see the numerous instances of this warning.
Since the move to W=1, there have not been many new instances that have
appeared through various build reports and the ones that have appeared
seem to be following similar existing patterns, suggesting that most
instances of this warning will not be real issues. The only alternatives
for silencing this warning are adding casts (which is generally seen as
an ugly practice) or refactoring the enums to macro defines or a unified
enum (which may be undesirable because of type safety in other parts of
the code).
Move the warning to W=2, where warnings that occur frequently but may be
relevant should reside.
Cc: stable@vger.kernel.org
Fixes: 75b5ab134bb5 ("kbuild: Move -Wenum-{compare-conditional,enum-conversion} into W=1")
Link: https://lore.kernel.org/ZwRA9SOcOjjLJcpi@google.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull smb client fixes from Steve French:
- Three DFS fixes: DFS mount fix, fix for noisy log msg and one to
remove some unused code
- SMB3 Lease fix
* tag 'v6.14rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: change lease epoch type from unsigned int to __u16
smb: client: get rid of kstrdup() in get_ses_refpath()
smb: client: fix noisy when tree connecting to DFS interlink targets
smb: client: don't trust DFSREF_STORAGE_SERVER bit
|
|
Jakub Kicinski says:
====================
net: improve core queue API handling while device is down
The core netdev_rx_queue_restart() doesn't currently take into account
that the device may be down. The current and proposed queue API
implementations deal with this by rejecting queue API calls while
the device is down. We can do better, in theory we can still allow
devmem binding when the device is down - we shouldn't stop and start
the queues just try to allocate the memory. The reason we allocate
the memory is that memory provider binding checks if any compatible
page pool has been created (page_pool_check_memory_provider()).
Alternatively we could reject installing MP while the device is down
but the MP assignment survives ifdown (so presumably MP doesn't cease
to exist while down), and in general we allow configuration while down.
Previously I thought we need this as a fix, but gve rejects page pool
calls while down, and so did Saeed in the patches he posted. So this
series just makes the core act more sensibly but practically should
be a noop for now.
v1: https://lore.kernel.org/20250205190131.564456-1-kuba@kernel.org
====================
Link: https://patch.msgid.link/20250206225638.1387810-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Resetting queues while the device is down should be legal.
Allow it, test it. Ideally we'd test this with a real device
supporting devmem but I don't have access to such devices.
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250206225638.1387810-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We expect NAPI to be in disabled state when page pool is torn down.
But it is also legal if the NAPI is completely uninitialized.
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250206225638.1387810-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We seem to be missing a netif_running() check from the devmem
installation path. Starting a queue on a stopped device makes
no sense. We still want to be able to allocate the memory, just
to test that the device is indeed setting up the page pools
in a memory provider compatible way.
This is not a bug fix, because existing drivers check if
the interface is down as part of the ops. But new drivers
shouldn't have to do this, as long as they can correctly
alloc/free while down.
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250206225638.1387810-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Shorten the lines by storing dev->queue_mgmt_ops in a temp variable.
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250206225638.1387810-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit dbae2b062824 ("net: skb: introduce and use a single
page frag cache"). The intended goal of such change was to counter a
performance regression introduced by commit 3226b158e67c ("net: avoid
32 x truesize under-estimation for tiny skbs").
Unfortunately, the blamed commit introduces another regression for the
virtio_net driver. Such a driver calls napi_alloc_skb() with a tiny
size, so that the whole head frag could fit a 512-byte block.
The single page frag cache uses a 1K fragment for such allocation, and
the additional overhead, under small UDP packets flood, makes the page
allocator a bottleneck.
Thanks to commit bf9f1baa279f ("net: add dedicated kmem_cache for
typical/small skb->head"), this revert does not re-introduce the
original regression. Actually, in the relevant test on top of this
revert, I measure a small but noticeable positive delta, just above
noise level.
The revert itself required some additional mangling due to the
introduction of the SKB_HEAD_ALIGN() helper and local lock infra in the
affected code.
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: dbae2b062824 ("net: skb: introduce and use a single page frag cache")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/e649212fde9f0fdee23909ca0d14158d32bb7425.1738877290.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phy_set_max_speed() to simplify init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/b863dcf7-31e8-45a1-a284-7075da958ff0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fabio Porcedda says:
====================
Add usb support for Telit Cinterion FN990B
Add usb support for Telit Cinterion FN990B.
Also fix Telit Cinterion FN990A name.
Connection with ModemManager was tested also AT ports.
====================
Link: https://patch.msgid.link/20250205171649.618162-1-fabio.porcedda@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The correct name for FN990 is FN990A so use it in order to avoid
confusion with FN990B.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Link: https://patch.msgid.link/20250205171649.618162-6-fabio.porcedda@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The correct name for FN990 is FN990A so use it in order to avoid
confusion with FN990B.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Link: https://patch.msgid.link/20250205171649.618162-5-fabio.porcedda@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the following Telit Cinterion FN990B composition:
0x10d0: rmnet + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10d0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN990
S: SerialNumber=43b38f19
C: #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Link: https://patch.msgid.link/20250205171649.618162-3-fabio.porcedda@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CPU usage time is the time when user, system or both are using the CPU.
Steal time is the time when CPU is waiting to be run by the Hypervisor. It
should not be added to the CPU usage time, hence removing it from the
usage_usec entry.
Fixes: 936f2a70f2077 ("cgroup: add cpu.stat file to root cgroup")
Acked-by: Axel Busch <axel.busch@ibm.com>
Acked-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Muhammad Adeel <muhammad.adeel@ibm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Just regular drm fixes, amdgpu, xe and i915 mostly, but a few
scattered fixes. I think one of the i915 fixes fixes some build combos
that Guenter was seeing.
amdgpu:
- Add new tiling flag for DCC write compress disable
- Add BO metadata flag for DCC
- Fix potential out of bounds access in display
- Seamless boot fix
- CONFIG_FRAME_WARN fix
- PSR1 fix
xe:
- OA uAPI related fixes
- Fix SRIOV migration initialization
- Restore devcoredump to a sane state
i915:
- Fix the build error with clamp after WARN_ON on gcc 13.x+
- HDCP related fixes
- PMU fix zero delta busyness issue
- Fix page cleanup on DMA remap failure
- Drop 64bpp YUV formats from ICL+ SDR planes
- GuC log related fix
- DisplayPort related fixes
ivpu:
- Fix error handling
komeda:
- add return check
zynqmp:
- fix locking in DP code
ast:
- fix AST DP timeout
cec:
- fix broken CEC adapter check"
* tag 'drm-fixes-2025-02-08' of https://gitlab.freedesktop.org/drm/kernel: (29 commits)
drm/i915/dp: Fix potential infinite loop in 128b/132b SST
Revert "drm/amd/display: Use HW lock mgr for PSR1"
drm/amd/display: Respect user's CONFIG_FRAME_WARN more for dml files
accel/amdxdna: Add MODULE_FIRMWARE() declarations
drm/i915/dp: Iterate DSC BPP from high to low on all platforms
drm/xe: Fix and re-enable xe_print_blob_ascii85()
drm/xe/devcoredump: Move exec queue snapshot to Contexts section
drm/xe/oa: Set stream->pollin in xe_oa_buffer_check_unlocked
drm/xe/pf: Fix migration initialization
drm/xe/oa: Preserve oa_ctrl unused bits
drm/amd/display: Fix seamless boot sequence
drm/amd/display: Fix out-of-bound accesses
drm/amdgpu: add a BO metadata flag to disable write compression for Vulkan
drm/i915/backlight: Return immediately when scale() finds invalid parameters
drm/i915/dp: Return min bpc supported by source instead of 0
drm/i915/dp: fix the Adaptive sync Operation mode for SDP
drm/i915/guc: Debug print LRC state entries only if the context is pinned
drm/i915: Drop 64bpp YUV formats from ICL+ SDR planes
drm/i915: Fix page cleanup on DMA remap failure
drm/i915/pmu: Fix zero delta busyness issue
...
|
|
Simplify rswitch_get_port_node() by using the
for_each_available_child_of_node() helper instead of manually ignoring
unavailable child nodes, and leaking a reference.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/54f544d573a64b96e01fd00d3481b10806f4d110.1738771798.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
net: stmmac: yet more EEE updates
Continuing on with the STMMAC EEE cleanups from last cycle, this series
further cleans up the EEE code, and fixes a problem with the existing
implementation - disabling EEE doesn't immediately disable LPI
signalling until the next packet is transmitted. It likely also fixes
a potential race condition when trying to disable LPI vs the software
timer.
====================
Link: https://patch.msgid.link/Z6NqGnM2yL7Ayo-T@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As we no longer call the set_eee_mode(), reset_eee_mode() and
set_eee_lpi_entry_timer() methods, remove these and their glue in
common.h
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffe7-003ZIm-Qv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the new stmmac_set_lpi_mode() API to configure the parameters of
the desired LPI mode rather than the older methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffe2-003ZIg-Mx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure that LPI_CTRL_STATUS_LPITCSE is also appropriately cleared when
disabling LPI or enabling LPI without TX clock gating.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdx-003ZIZ-JQ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new method to control LPI mode configuration. This is architected
to have three configuration states: LPI disabled, LPI forced (active),
or LPI under hardware timer control. This reflects the three modes
which the main body of the driver wishes to deal with.
We pass in whether transmit clock gating should be used, and the
hardware timer value in microseconds to be set when using hardware
timer control.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffds-003ZIT-E8@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bit definitions for the LPI control/status register are
identical across all MAC versions, with the exception that some
bits may not be implemented. Provide definitions for bits in this
register in common.h, convert to use them, and remove the core-
specific definitions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdn-003ZIN-9p@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the unnecessary LPI disable when enabling LPI - as noted in
previous commits, there will never be two consecutive calls to
stmmac_mac_enable_tx_lpi() without an intervening
stmmac_mac_disable_tx_lpi.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdi-003ZIH-5h@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As other code paths do, clear priv->tx_path_in_lpi_mode when disabling
LPI. This is done after the software timer has been deleted and
hardware LPI has been disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdd-003ZIB-22@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Phylink will not call the mac_disable_tx_lpi() and mac_enable_tx_lpi()
methods randomly - the first method to be called will be the enable
method, and then after, the disable method will be called once between
subsequent enable calls. Thus there is a guaranteed ordering.
Therefore, we know the previous state of priv->eee_enabled, and can
remove it from both methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdX-003ZI5-UV@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since priv->eee_active is assigned with a constant value in each of
these methods, there is no need to test its value later. Remove these
unnecessary tests.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdS-003ZHz-Qi@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The tests for priv->dma_cap.eee in stmmac_mac_{en,dis}able_tx_lpi()
is useless as these methods will only be called when using phylink
managed EEE, and that will only be enabled if the LPI capabilities
in phylink_config have been populated during initialisation. This
only occurs when priv->dma_cap.eee was true.
As priv->dma_cap.eee remains constant during the lifetime of the driver
instance, there is no need to re-check it in these methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdN-003ZHt-Mq@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the appropriate parts of stmmac_init_eee() into the phylink
mac_enable_tx_lpi() and mac_disable_tx_lpi() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdI-003ZHn-Iz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LPIATE enables the hardware timer for entering LPI mode. To sure that
the correct mode is used, clear LPIATE when using manual/software-timed
mode to prevent the hardware using the timer.
stmmac_main.c avoids this being a problem at the moment by calling
stmmac_set_eee_lpi_timer(..., 0) before switching to software mode.
We no longer need to call stmmac_set_eee_lpi_timer(..., 0) when
disabling EEE as stmmac_reset_eee_mode() will now clear all LPI
settings.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffdD-003ZHh-Ew@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When EEE is disabled, we call stmmac_set_eee_lpi_timer(..., 0).
For dwmac4, this will result in LPIATE being cleared, but LPIEN and
LPITXA being set, causing LPI mode to be signalled (if it wasn't
before).
For others MACs, stmmac_set_eee_lpi_timer() does nothing, which means
that LPI mode will continue to be signalled despite the expectation
for it to be disabled.
In both cases, LPI mode will be terminated when the transmitter has
a packet to send, and LPIEN will be cleared by hardware.
Call stmmac_reset_eee_mode() to ensure that LPI mode is disabled when
EEE mode is requested to be disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffd8-003ZHb-AX@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Delete the software timer to ensure that the timer doesn't fire while
we are modifying the LPI register state, potentially re-enabling LPI.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tffd3-003ZHV-6C@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
inet_csk_delete_keepalive_timer() and inet_csk_reset_keepalive_timer()
are only used from core TCP, there is no need to export them.
Replace their prefix by tcp.
Move them to net/ipv4/tcp_timer.c and make tcp_delete_keepalive_timer()
static.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250206094605.2694118-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These two functions are not called from modules.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250206093436.2609008-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rule->iifindex and rule->oifindex can be read without holding RTNL.
Add READ_ONCE()/WRITE_ONCE() annotations where needed.
Fixes: 32affa5578f0 ("fib: rules: no longer hold RTNL in fib_nl_dumprule()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250206083051.2494877-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
