| Age | Commit message (Collapse) | Author |
|---|
|
Previous implementation was not usable with CONFIG_IPV6=m.
Fixes: a3419ce3356c ("netfilter: nf_conntrack_sip: add sip_external_media logic")
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add TI PHY strap ctrl quirk for all the HW where applicable.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
kthread name only allows 15 characters (TASK_COMMON_LEN is 16).
Thus rename the kthreads created by intel_powerclamp driver from
"kidle_inject/ + decimal cpuid" to "kidle_inj/ + decimal cpuid"
to avoid truncated kthead name for cpu 100 and later.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The mtk_thermal struct contains a 'struct mtk_thermal_bank banks[];',
but the allocation only allocates sizeof(struct mtk_thermal) bytes,
which cause out of bound access with the ->banks[] member. Change it to
a fixed size array instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Commit 758a58d0bc67 ("loop: set GENHD_FL_NO_PART_SCAN after
blkdev_reread_part()") separates "lo->lo_backing_file = NULL" and
"lo->lo_state = Lo_unbound" into different critical regions protected by
loop_ctl_mutex.
However, there is below race that the NULL lo->lo_backing_file would be
accessed when the backend of a loop is another loop device, e.g., loop0's
backend is a file, while loop1's backend is loop0.
loop0's backend is file loop1's backend is loop0
__loop_clr_fd()
mutex_lock(&loop_ctl_mutex);
lo->lo_backing_file = NULL; --> set to NULL
mutex_unlock(&loop_ctl_mutex);
loop_set_fd()
mutex_lock_killable(&loop_ctl_mutex);
loop_validate_file()
f = l->lo_backing_file; --> NULL
access if loop0 is not Lo_unbound
mutex_lock(&loop_ctl_mutex);
lo->lo_state = Lo_unbound;
mutex_unlock(&loop_ctl_mutex);
lo->lo_backing_file should be accessed only when the loop device is
Lo_bound.
In fact, the problem has been introduced already in commit 7ccd0791d985
("loop: Push loop_ctl_mutex down into loop_clr_fd()") after which
loop_validate_file() could see devices in Lo_rundown state with which it
did not count. It was harmless at that point but still.
Fixes: 7ccd0791d985 ("loop: Push loop_ctl_mutex down into loop_clr_fd()")
Reported-by: syzbot+9bdc1adc1c55e7fe765b@syzkaller.appspotmail.com
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Let blk_mq_mark_tag_wait() use the blk_mq_sched_mark_restart_hctx()
to set BLK_MQ_S_SCHED_RESTART.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
int3400 only pushes the UUID into the firmware when the mode is flipped
to "enable". The current code only exposes the mode flag if the firmware
supports the PASSIVE_1 UUID, which not all machines do. Remove the
restriction.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Add more supported DPTF policies than the driver currently exposes.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Cc: Nisha Aram <nisha.aram@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The 'cur_freq' local variable became unused after commit 84fe2cab4859
("cpu_cooling: Drop static-power related stuff"), let's remove it.
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Javi Merino <javi.merino@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
"cat /sys/kernel/debug/bcm2835_thermal/regset" causes a NULL pointer
dereference in bcm2835_thermal_debugfs. The driver makes use of the
implementation details of the thermal framework to retrieve a pointer
to its private data from a struct thermal_zone_device, and gets it
wrong - leading to the crash. Instead, store its private data as the
drvdata and retrieve the thermal_zone_device pointer from it.
Fixes: bcb7dd9ef206 ("thermal: bcm2835: add thermal driver for bcm2835 SoC")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Merge commit 19785cf93b6c ("Merge branch 'linus' of
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal")
broke the code introduced by commit ffe6e16f14fa ("thermal: exynos: Reduce
severity of too early temperature read"). Restore the original code from
the mentioned commit to finally fix the warning message during boot:
thermal thermal_zone0: failed to read out thermal zone (-22)
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 19785cf93b6c ("Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
This variable is declared as:
static struct powerclamp_worker_data * __percpu worker_data;
In other words, a percpu pointer to struct ...
But this variable not used like so but as a pointer to a percpu
struct powerclamp_worker_data.
So fix the declaration as:
static struct powerclamp_worker_data __percpu *worker_data;
This also quiets Sparse's warnings from __verify_pcpu_ptr(), like:
494:49: warning: incorrect type in initializer (different address spaces)
494:49: expected void const [noderef] <asn:3> *__vpp_verify
494:49: got struct powerclamp_worker_data *
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The driver allocates queues for all the units it potentially
supports. But if we fail to detect any drives, then we fail
loading the module without cleaning up those queues. This is
now evident with the switch to blk-mq, though the bug has
been there forever as far as I can tell.
Also fix cleanup through regular module exit.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The driver allocates queues for all the units it potentially
supports. But if we fail to detect any drives, then we fail
loading the module without cleaning up those queues. This is
now evident with the switch to blk-mq, though the bug has
been there forever as far as I can tell.
Also fix cleanup through regular module exit.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Not only the 603 but all 6xx need SPRN_SPRG_PGDIR to be initialised at
startup. This patch move it from __setup_cpu_603() to start_here()
and __secondary_start(), close to the initialisation of SPRN_THREAD.
Previously, virt addr of PGDIR was retrieved from thread struct.
Now that it is the phys addr which is stored in SPRN_SPRG_PGDIR,
hash_page() shall not convert it to phys anymore.
This patch removes the conversion.
Fixes: 93c4a162b014 ("powerpc/6xx: Store PGDIR physical address in a SPRG")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The function snd_opl3_drum_switch declaration in the header file
has the order of the two arguments on_off and vel swapped when
compared to the definition arguments of vel and on_off. Fix this
by swapping them around to match the definition.
This error predates the git history, so no idea when this error
was introduced.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Another machine which does not like the power saving (noise):
https://bugzilla.redhat.com/show_bug.cgi?id=1689623
Also, reorder the Lenovo C50 entry to keep the table sorted.
Reported-by: hs.guimaraes@outlook.com
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Clock description is part of firmware doc. Move clock description
in separate doc.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Rename file name of ZynqMP clk dt-bindings to align with
file name of reset and power dt-bindings.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Take into account that sg->offset can be bigger than PAGE_SIZE when
setting segment sg->dma_address. Otherwise sg->dma_address will point
at diffrent page, what makes DMA not possible with erros like this:
xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa70c0 flags=0x0020]
xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7040 flags=0x0020]
xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7080 flags=0x0020]
xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7100 flags=0x0020]
xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7000 flags=0x0020]
Additinally with wrong sg->dma_address unmap_sg will free wrong pages,
what what can cause crashes like this:
Feb 28 19:27:45 kernel: BUG: Bad page state in process cinnamon pfn:39e8b1
Feb 28 19:27:45 kernel: Disabling lock debugging due to kernel taint
Feb 28 19:27:45 kernel: flags: 0x2ffff0000000000()
Feb 28 19:27:45 kernel: raw: 02ffff0000000000 0000000000000000 ffffffff00000301 0000000000000000
Feb 28 19:27:45 kernel: raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
Feb 28 19:27:45 kernel: page dumped because: nonzero _refcount
Feb 28 19:27:45 kernel: Modules linked in: ccm fuse arc4 nct6775 hwmon_vid amdgpu nls_iso8859_1 nls_cp437 edac_mce_amd vfat fat kvm_amd ccp rng_core kvm mt76x0u mt76x0_common mt76x02_usb irqbypass mt76_usb mt76x02_lib mt76 crct10dif_pclmul crc32_pclmul chash mac80211 amd_iommu_v2 ghash_clmulni_intel gpu_sched i2c_algo_bit ttm wmi_bmof snd_hda_codec_realtek snd_hda_codec_generic drm_kms_helper snd_hda_codec_hdmi snd_hda_intel drm snd_hda_codec aesni_intel snd_hda_core snd_hwdep aes_x86_64 crypto_simd snd_pcm cfg80211 cryptd mousedev snd_timer glue_helper pcspkr r8169 input_leds realtek agpgart libphy rfkill snd syscopyarea sysfillrect sysimgblt fb_sys_fops soundcore sp5100_tco k10temp i2c_piix4 wmi evdev gpio_amdpt pinctrl_amd mac_hid pcc_cpufreq acpi_cpufreq sg ip_tables x_tables ext4(E) crc32c_generic(E) crc16(E) mbcache(E) jbd2(E) fscrypto(E) sd_mod(E) hid_generic(E) usbhid(E) hid(E) dm_mod(E) serio_raw(E) atkbd(E) libps2(E) crc32c_intel(E) ahci(E) libahci(E) libata(E) xhci_pci(E) xhci_hcd(E)
Feb 28 19:27:45 kernel: scsi_mod(E) i8042(E) serio(E) bcache(E) crc64(E)
Feb 28 19:27:45 kernel: CPU: 2 PID: 896 Comm: cinnamon Tainted: G B W E 4.20.12-arch1-1-custom #1
Feb 28 19:27:45 kernel: Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./B450M Pro4, BIOS P1.20 06/26/2018
Feb 28 19:27:45 kernel: Call Trace:
Feb 28 19:27:45 kernel: dump_stack+0x5c/0x80
Feb 28 19:27:45 kernel: bad_page.cold.29+0x7f/0xb2
Feb 28 19:27:45 kernel: __free_pages_ok+0x2c0/0x2d0
Feb 28 19:27:45 kernel: skb_release_data+0x96/0x180
Feb 28 19:27:45 kernel: __kfree_skb+0xe/0x20
Feb 28 19:27:45 kernel: tcp_recvmsg+0x894/0xc60
Feb 28 19:27:45 kernel: ? reuse_swap_page+0x120/0x340
Feb 28 19:27:45 kernel: ? ptep_set_access_flags+0x23/0x30
Feb 28 19:27:45 kernel: inet_recvmsg+0x5b/0x100
Feb 28 19:27:45 kernel: __sys_recvfrom+0xc3/0x180
Feb 28 19:27:45 kernel: ? handle_mm_fault+0x10a/0x250
Feb 28 19:27:45 kernel: ? syscall_trace_enter+0x1d3/0x2d0
Feb 28 19:27:45 kernel: ? __audit_syscall_exit+0x22a/0x290
Feb 28 19:27:45 kernel: __x64_sys_recvfrom+0x24/0x30
Feb 28 19:27:45 kernel: do_syscall_64+0x5b/0x170
Feb 28 19:27:45 kernel: entry_SYSCALL_64_after_hwframe+0x44/0xa9
Cc: stable@vger.kernel.org
Reported-and-tested-by: Jan Viktorin <jan.viktorin@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Fixes: 80187fd39dcb ('iommu/amd: Optimize map_sg and unmap_sg')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Building with clang finds a mistaken __init tag:
WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host()
The function davinci_mmcsd_probe() references
the function __init init_mmcsd_host().
This is often because davinci_mmcsd_probe lacks a __init
annotation or the annotation of init_mmcsd_host is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
clang points out several instances of mismatched types in this drivers,
all coming from a single declaration:
drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to
different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion]
direction = DMA_DEV_TO_MEM;
~ ^~~~~~~~~~~~~~
drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to
different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion]
tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction,
The behavior is correct, so this must be a simply typo from
dma_data_direction and dma_transfer_direction being similarly named
types with a similar purpose.
Fixes: 6464b7140951 ("mmc: pxamci: switch over to dmaengine use")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On Ebisu the DDR0 power rail needs to be kept powered when backup mode is
enabled. Reflect this in the "rohm,ddr-backup-power" property for the
BD9571MWV PMIC node.
The accessory power switch (SW23) is a toggle switch, hence specify
"rohm,rstbmode-level".
Based on advice from Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds the regulator definition required for operation of
S2RAM.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The compatible value renesas,rcar-gen3-csi2 was used while prototyping
the R-Car CSI-2 driver but was removed before the driver was merged.
Remove the only occurrence of the compatible value which manage to make
it upstream.
Fixes: ec70407ae7d7 ("arm64: dts: renesas: r8a77990: Add VIN and CSI-2 device nodes")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The compatible value renesas,rcar-gen3-csi2 was used while prototyping
the R-Car CSI-2 driver but was removed before the driver was merged.
Fixes: e961ab42e034d469 ("arm64: dts: renesas: r8a774c0: Add VIN and CSI-2 device nodes")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable both CAN0 and CAN1 controllers on R8A77995 Draak board,
since they are available on connectors CN43, CN44 respectively.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable RWDT and use 60 seconds as default timeout.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Both VIN4 and VIN5 are connected to CSI40 and can be configured at
runtime to use the single video source connected to CSI40. Enable VIN5
to allow it to be used in this fashion.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Niklas: rewrite commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds LEDs support to the CAT874 board specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds Epson RX-8571 real time clock support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add CAN support to the CAT875 sub board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
We usually leave a space between "=" and the value of device
tree properties, but unfortunately that was overlooked for the
"clocks" property of cpu@0 and cpu@1.
This patch fixes the spacing with the "clocks" property of
cpu@0 and cpu@1.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
rsnd driver supports SSIU now, let's use it.
Then, BUSIF DMA settings on rcar_sound,ssi (= rxu, txu) are
no longer needed.
Applies commit 8d14bfa074db ("arm64: dts: renesas: r8a7796: add SSIU
support for sound") and commit 10bd03fa896e ("arm64: dts: renesas:
r8a7796: remove BUSIF0 settings from rcar_sound,ssi") for r8a77965.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The register address used for the reg property of the adv7482 node in
other Renesas device trees are decimal not hex, change this for Ebisu to
align it with the others.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Niklas: rewrite commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The LVDS1 encoder must supply a pixel clock to the DU for the DPAD
output when the LVDS0 encoder is used. Enable it despite its output not
being connected.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The LVDS1 encoder must supply a pixel clock to the DU for the DPAD
output when the LVDS0 encoder is used. Enable it despite its output not
being connected.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
commit 78bc93b3ffb2 ("arm64: dts: renesas: r8a7796: Add address
properties to rcar_sound port nodes") added missing #address-cells
and #size-cells for sound ports.
But, these are based on platform, not on SoC. This patch cleanups it.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to Documentation/process/license-rules.rst, SPDX license
identifiers in DTS files should use C++ style comments.
Fixes: f37a7767f6c4ec66 ("arm64: dts: renesas: Add Renesas R8A77990 SoC support")
Fixes: 77049191b24b4586 ("arm64: dts: renesas: Add Renesas Ebisu board support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Describe the ON Semiconductor PCA9654 I/O expander on the first I2C
bus, which provides 8 extra GPIOs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Jakub Drnec reported:
Setting the realtime clock can sometimes make the monotonic clock go
back by over a hundred years. Decreasing the realtime clock across
the y2k38 threshold is one reliable way to reproduce. Allegedly this
can also happen just by running ntpd, I have not managed to
reproduce that other than booting with rtc at >2038 and then running
ntp. When this happens, anything with timers (e.g. openjdk) breaks
rather badly.
And included a test case (slightly edited for brevity):
#define _POSIX_C_SOURCE 199309L
#include <stdio.h>
#include <time.h>
#include <stdlib.h>
#include <unistd.h>
long get_time(void) {
struct timespec tp;
clock_gettime(CLOCK_MONOTONIC, &tp);
return tp.tv_sec + tp.tv_nsec / 1000000000;
}
int main(void) {
long last = get_time();
while(1) {
long now = get_time();
if (now < last) {
printf("clock went backwards by %ld seconds!\n", last - now);
}
last = now;
sleep(1);
}
return 0;
}
Which when run concurrently with:
# date -s 2040-1-1
# date -s 2037-1-1
Will detect the clock going backward.
The root cause is that wtom_clock_sec in struct vdso_data is only a
32-bit signed value, even though we set its value to be equal to
tk->wall_to_monotonic.tv_sec which is 64-bits.
Because the monotonic clock starts at zero when the system boots the
wall_to_montonic.tv_sec offset is negative for current and future
dates. Currently on a freshly booted system the offset will be in the
vicinity of negative 1.5 billion seconds.
However if the wall clock is set past the Y2038 boundary, the offset
from wall to monotonic becomes less than negative 2^31, and no longer
fits in 32-bits. When that value is assigned to wtom_clock_sec it is
truncated and becomes positive, causing the VDSO assembly code to
calculate CLOCK_MONOTONIC incorrectly.
That causes CLOCK_MONOTONIC to jump ahead by ~4 billion seconds which
it is not meant to do. Worse, if the time is then set back before the
Y2038 boundary CLOCK_MONOTONIC will jump backward.
We can fix it simply by storing the full 64-bit offset in the
vdso_data, and using that in the VDSO assembly code. We also shuffle
some of the fields in vdso_data to avoid creating a hole.
The original commit that added the CLOCK_MONOTONIC support to the VDSO
did actually use a 64-bit value for wtom_clock_sec, see commit
a7f290dad32e ("[PATCH] powerpc: Merge vdso's and add vdso support to
32 bits kernel") (Nov 2005). However just 3 days later it was
converted to 32-bits in commit 0c37ec2aa88b ("[PATCH] powerpc: vdso
fixes (take #2)"), and the bug has existed since then AFAICS.
Fixes: 0c37ec2aa88b ("[PATCH] powerpc: vdso fixes (take #2)")
Cc: stable@vger.kernel.org # v2.6.15+
Link: http://lkml.kernel.org/r/HaC.ZfES.62bwlnvAvMP.1STMMj@seznam.cz
Reported-by: Jakub Drnec <jaydee@email.cz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If drm_gem_handle_create() fails in vkms_gem_create(), then the
vkms_gem_object is freed twice: once when the reference is dropped by
drm_gem_object_put_unlocked(), and again by the extra calls to
drm_gem_object_release() and kfree().
Fix it by skipping the second release and free.
This bug was originally found in the vgem driver by syzkaller using
fault injection, but I noticed it's also present in the vkms driver.
Fixes: 559e50fd34d1 ("drm/vkms: Add dumb operations")
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226220858.214438-1-ebiggers@kernel.org
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
If drm_gem_handle_create() fails in vgem_gem_create(), then the
drm_vgem_gem_object is freed twice: once when the reference is dropped
by drm_gem_object_put_unlocked(), and again by __vgem_gem_destroy().
This was hit by syzkaller using fault injection.
Fix it by skipping the second free.
Reported-by: syzbot+e73f2fb5ed5a5df36d33@syzkaller.appspotmail.com
Fixes: af33a9190d02 ("drm/vgem: Enable dmabuf import interfaces")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226214451.195123-1-ebiggers@kernel.org
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The nanopi4 boards have the INTB pin of the RTL8211E phy wired up, so we
can make use of that and avoid having to poll for line status changes.
Apparently RTL8211E only requires 30ms of post-reset delay, so we may as
well save a little bit of time there as well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
NanoPC-T4 has a dedicated circuit for driving a 12V fan from PWM1,
so let's add that along with some rough empirically-derived thermal
settings for the benefit of anyone determined enough to hook one up.
The vendor does not currently offer a suitable fan, but this seems as
good a place as any to note that pre-terminated 3-pin JST GH connectors
are readily available online, and if you even have to ask, then splicing
one of those really will be orders of magnitude cheaper and simpler than
getting set up to crimp the teeny-tiny things by hand.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Also rename its regulator to match the schematic names.
Signed-off-by: Alexis Ballier <aballier@gentoo.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
(AK09911)
Despite this not being mentioned in the binding documentation, this
generates a log at boot about it being missing.
Signed-off-by: Alexis Ballier <aballier@gentoo.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
on rk3399-orangepi
Clock name was wrong, vbat & vddio supplies were missing.
Signed-off-by: Alexis Ballier <aballier@gentoo.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
12V DCIN regulator is root source supply for the rest of regulators
in Rock960 power diagram.
Add support for it and attach same to supply vcc5v0_sys.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
