| Age | Commit message (Collapse) | Author |
|---|
|
We don't wakeup the virtqueue if the first byte of pending iova range
is the last byte of the range we just got updated. This will lead a
virtqueue to wait for IOTLB updating forever. Fixing by correct the
check and wake up the virtqueue in this case.
Fixes: 6b1e6cc7855b ("vhost: new device IOTLB API")
Reported-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes: 6c36a7074436 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit bde4975310eb1982bd0bbff673989052d92fd481.
All legacy clock implementations now implement clk_set_rate() (Some
implementations may be dummies, though).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 739de9a1563a ("net: macb: Reorganize macb_mii bringup") broke
initializing macb on the EVB-KSZ9477 eval board.
There, of_mdiobus_register was called even for the fixed-link representing
the RGMII-link to the switch with the result that the driver attempts to
enumerate PHYs on a non-existent MDIO bus:
libphy: MACB_mii_bus: probed
mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0
[snip]
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31
The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO,
and calling of_phy_register_fixed_link later on fails because it tries
to claim the same GPIO:
macb f0028000.ethernet: broken fixed-link specification
Fix this by registering the fixed-link before calling mdiobus_register.
Fixes: 739de9a1563a ("net: macb: Reorganize macb_mii bringup")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu/rockchip: Move irq request past pm_runtime_enable
iommu/rockchip: Handle errors returned from PM framework
arm64: rockchip: Force CONFIG_PM on Rockchip systems
ARM: rockchip: Force CONFIG_PM on Rockchip systems
arm64: dts: Fix various entry-method properties to reflect documentation
reset: imx7: Fix always writing bits as 0
reset: meson: add meson audio arb driver
reset: meson: add dt-bindings for meson-axg audio arb
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
* tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: rename LDFLAGS to KBUILD_LDFLAGS
kbuild: pass LDFLAGS to recordmcount.pl
kbuild: test dead code/data elimination support in Kconfig
initramfs: move gen_initramfs_list.sh from scripts/ to usr/
vmlinux.lds.h: remove stale <linux/export.h> include
export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR()
Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci
kbuild: make sorting initramfs contents independent of locale
kbuild: remove "rpm" target, which is alias of "rpm-pkg"
kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt
kconfig: suppress "configuration written to .config" for syncconfig
kconfig: fix "Can't open ..." in parallel build
kbuild: Add a space after `!` to prevent parsing as file pattern
scripts: modpost: check memory allocation results
kconfig: improve the recursive dependency report
kconfig: report recursive dependency involving 'imply'
kconfig: error out when seeing recursive dependency
kconfig: add build-only configurator targets
scripts/dtc: consolidate include path options in Makefile
|
|
Pull block fixes from Jens Axboe:
"A few small fixes for this merge window:
- Locking imbalance fix for bcache (Shan Hai)
- A few small fixes for wbt. One is a cleanup/prep, one is a fix for
an existing issue, and the last two are fixes for changes that went
into this merge window (me)"
* tag 'for-linus-20180825' of git://git.kernel.dk/linux-block:
blk-wbt: don't maintain inflight counts if disabled
blk-wbt: fix has-sleeper queueing check
blk-wbt: use wq_has_sleeper() for wq active check
blk-wbt: move disable check into get_limit()
bcache: release dc->writeback_lock properly in bch_writeback_thread()
|
|
Pull UBIFS fix from Richard Weinberger:
"Remove an empty file from UBIFS source"
* tag 'upstream-4.19-rc1-fix' of git://git.infradead.org/linux-ubifs:
ubifs: Remove empty file.h
|
|
Pull cifs fixes from Steve French:
"Three small SMB3 fixes, one for stable"
* tag '4.19-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number for cifs.ko to 2.12
cifs: check kmalloc before use
cifs: check if SMB2 PDU size has been padded and suppress the warning
cifs: create a define for how many iovs we need for an SMB2_open()
|
|
This is not normally noticeable, but repeated forks are unnecessarily
expensive because they repeatedly dirty the parent page tables during
the page table copy operation.
It's trivial to just avoid write protecting the page table entry if it
was already not writable.
This patch was inspired by
https://bugzilla.kernel.org/show_bug.cgi?id=200447
which points to an ancient "waste time re-doing fork" issue in the
presence of lots of signals.
That bug was fixed by Eric Biederman's signal handling series
culminating in commit c3ad2c3b02e9 ("signal: Don't restart fork when
signals come in"), but the unnecessary work for repeated forks is still
work just fixing, particularly since the fix is trivial.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
At the point where r is being checked for different values, r is always
going to be equal to 2 as the previous if statements jump to end or end1
if r is not 2. Hence the assignment to err can be simplified to just
err an assignment without any checks on the value or r.
Detected by CoverityScan, CID#1226737 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tejun Heo wrote:
>
> I asked Jens whether he could take care of the libata tree and he
> thankfully agreed, so, from now on, Jens will be the libata
> maintainer.
>
> Thanks a lot!
Thanks for your work in this area. I still remember the first linux
storage summit we did in Vancouver 2001, Tejun was invited to talk about
his libata error handling work. Before that, it was basically a crap
shoot if we recovered properly or not... A lot of water has flown under
the bridge since then!
Here's an "official" patch. Linus, can you apply it?
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
backlog submissions.
Earlier used to post the current command without checking queue full
after backlog submissions. So, post the current command only after
confirming the space in queue after backlog submissions.
Maintain host write index instead of reading device registers
to get the next free slot to post the command.
Return -ENOSPC in queue full case.
Signed-off-by: Srikanth Jampala <Jampala.Srikanth@cavium.com>
Reviewed-by: Gadam Sreerama <sgadam@cavium.com>
Tested-by: Jha, Chandan <Chandan.Jha@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch fixes sleep-in-atomic bugs in AES-CBC and AES-XTS VMX
implementations. The problem is that the blkcipher_* functions should
not be called in atomic context.
The bugs can be reproduced via the AF_ALG interface by trying to
encrypt/decrypt sufficiently large buffers (at least 64 KiB) using the
VMX implementations of 'cbc(aes)' or 'xts(aes)'. Such operations then
trigger BUG in crypto_yield():
[ 891.863680] BUG: sleeping function called from invalid context at include/crypto/algapi.h:424
[ 891.864622] in_atomic(): 1, irqs_disabled(): 0, pid: 12347, name: kcapi-enc
[ 891.864739] 1 lock held by kcapi-enc/12347:
[ 891.864811] #0: 00000000f5d42c46 (sk_lock-AF_ALG){+.+.}, at: skcipher_recvmsg+0x50/0x530
[ 891.865076] CPU: 5 PID: 12347 Comm: kcapi-enc Not tainted 4.19.0-0.rc0.git3.1.fc30.ppc64le #1
[ 891.865251] Call Trace:
[ 891.865340] [c0000003387578c0] [c000000000d67ea4] dump_stack+0xe8/0x164 (unreliable)
[ 891.865511] [c000000338757910] [c000000000172a58] ___might_sleep+0x2f8/0x310
[ 891.865679] [c000000338757990] [c0000000006bff74] blkcipher_walk_done+0x374/0x4a0
[ 891.865825] [c0000003387579e0] [d000000007e73e70] p8_aes_cbc_encrypt+0x1c8/0x260 [vmx_crypto]
[ 891.865993] [c000000338757ad0] [c0000000006c0ee0] skcipher_encrypt_blkcipher+0x60/0x80
[ 891.866128] [c000000338757b10] [c0000000006ec504] skcipher_recvmsg+0x424/0x530
[ 891.866283] [c000000338757bd0] [c000000000b00654] sock_recvmsg+0x74/0xa0
[ 891.866403] [c000000338757c10] [c000000000b00f64] ___sys_recvmsg+0xf4/0x2f0
[ 891.866515] [c000000338757d90] [c000000000b02bb8] __sys_recvmsg+0x68/0xe0
[ 891.866631] [c000000338757e30] [c00000000000bbe4] system_call+0x5c/0x70
Fixes: 8c755ace357c ("crypto: vmx - Adding CBC routines for VMX module")
Fixes: c07f5d3da643 ("crypto: vmx - Adding support for XTS")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 71e52c278c54 ("crypto: arm64/aes-ce-gcm - operate on
two input blocks at a time") modified the granularity at which
the AES/GCM code processes its input to allow subsequent changes
to be applied that improve performance by using aggregation to
process multiple input blocks at once.
For this reason, it doubled the algorithm's 'chunksize' property
to 2 x AES_BLOCK_SIZE, but retained the non-SIMD fallback path that
processes a single block at a time. In some cases, this violates the
skcipher scatterwalk API, by calling skcipher_walk_done() with a
non-zero residue value for a chunk that is expected to be handled
in its entirety. This results in a WARN_ON() to be hit by the TLS
self test code, but is likely to break other user cases as well.
Unfortunately, none of the current test cases exercises this exact
code path at the moment.
Fixes: 71e52c278c54 ("crypto: arm64/aes-ce-gcm - operate on two ...")
Reported-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
A regression was reported bisecting to 1476db2d12
"Move HashKey computation from stack to gcm_context". That diff
moved HashKey computation from the stack, which was explicitly aligned
in the asm, to a struct provided from the C code, depending on
AESNI_ALIGN_ATTR for alignment. It appears some compilers may not
align this struct correctly, resulting in a crash on the movdqa
instruction when attempting to encrypt or decrypt data.
Fix by using unaligned loads for the HashKeys. On modern
hardware there is no perf difference between the unaligned and
aligned loads. All other accesses to gcm_context_data already use
unaligned loads.
Reported-by: Mauro Rossi <issor.oruam@gmail.com>
Fixes: 1476db2d12 ("Move HashKey computation from stack to gcm_context")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
call chtls_free_uld() only for the initialized cdev,
this fixes NULL dereference in chtls_free_uld()
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
ARMv8.2 specifies special instructions for the SM3 cryptographic hash
and the SM4 symmetric cipher. While it is unlikely that a core would
implement one and not the other, we should only use SM4 instructions
if the SM4 CPU feature bit is set, and we currently check the SM3
feature bit instead. So fix that.
Fixes: e99ce921c468 ("crypto: arm64 - add support for SM4...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Crypto engine needs some temporary locations in external memory for
running RSA decrypt forms 2 and 3 (CRT).
These are named "tmp1" and "tmp2" in the PDB.
Update DMA mapping direction of tmp1 and tmp2 from TO_DEVICE to
BIDIRECTIONAL, since engine needs r/w access.
Cc: <stable@vger.kernel.org> # 4.13+
Fixes: 52e26d77b8b3 ("crypto: caam - add support for RSA key form 2")
Fixes: 4a651b122adb ("crypto: caam - add support for RSA key form 3")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
xts setkey callback returns 0 on some error paths.
Fix this by returning -EINVAL.
Cc: <stable@vger.kernel.org> # 4.12+
Fixes: b189817cf789 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Descriptor address needs to be swapped to CPU endianness before being
DMA unmapped.
Cc: <stable@vger.kernel.org> # 4.8+
Fixes: 261ea058f016 ("crypto: caam - handle core endianness != caam endianness")
Reported-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The case addressed by commit 5ef499cd571c (cpuidle: menu: Handle
stopped tick more aggressively) in the stopped tick case is present
when the tick has not been stopped yet too. Namely, if only two CPU
idle states, shallow state A with target residency significantly
below the tick boundary and deep state B with target residency
significantly above it, are available and the predicted idle
duration is above the tick boundary, but below the target residency
of state B, state A will be selected and the CPU may spend indefinite
amount of time in it, which is not quite energy-efficient.
However, if the tick has not been stopped yet and the governor is
about to select a shallow idle state for the CPU even though the idle
duration predicted by it is above the tick boundary, it should be
fine to wake up the CPU early, so the tick can be retained then and
the governor will have a chance to select a deeper state when it runs
next time.
[Note that when this really happens, it will make the idle duration
predictor believe that the CPU might be idle longer than predicted,
which will make it more likely to predict longer idle durations going
forward, but that will also cause deeper idle states to be selected
going forward, on average, which is what's needed here.]
Fixes: 87c9fe6ee495 (cpuidle: menu: Avoid selecting shallow states with stopped tick)
Reported-by: Leo Yan <leo.yan@linaro.org>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+: 5ef499cd571c (cpuidle: menu: Handle ...)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-08-24
This series contains fixes to e1000, igb, ixgb, ixgbe and i40e.
YueHaibing from Huawei provides a change to use dma_zalloc_coherent()
instead of calls to allocator followed by a memset for ixgb.
Bo Chen provides a couple of fixes for e1000, first by adding a check to
prevent a NULL pointer dereference. The second change is to clean up a
possible resource leak on old transmit and receive rings when the device
is not up.
Jesus fixes an issue in the usage of an advanced transmit context
descriptor for retrieving the timestamp of a packet for AF_PACKET if the
IGB_TX_FLAGS_VLAN is not set in igb.
Jia-Ju Bai provides several patches which replace GFP_ATOMIC with
GFP_KERNEL, when using kzalloc() and kcalloc() which is not necessary.
Also found an instance of mdelay() call which could be replaced with
msleep().
Tony fixes ixgbe to allow MTU changes with XDP, by adding checks to
ensure only supported values and return -EINVAL for when it is not
supported.
Sebastian fixed an issue that was not clearing VF mailbox memory and
ensure queues are re-enabled correctly.
Martyna fixes a transmit timeout when DCB is configured when bringing up
an interface.
Jake fixes a previous commit which accidentally reversed the check of
the data pointer, so we can accurately count the size of the stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"Just one commit from Steven to take out spin lock from trace event
handlers"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/tracing: Move taking of spin lock out of trace event handlers
|
|
Pull workqueue updates from Tejun Heo:
"Over the lockdep cross-release churn, workqueue lost some of the
existing annotations. Johannes Berg restored it and also improved
them"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: re-add lockdep dependencies for flushing
workqueue: skip lockdep wq dependency in cancel_work_sync()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- PASID table handling updates for the Intel VT-d driver. It implements
a global PASID space now so that applications usings multiple devices
will just have one PASID.
- A new config option to make iommu passthroug mode the default.
- New sysfs attribute for iommu groups to export the type of the
default domain.
- A debugfs interface (for debug only) usable by IOMMU drivers to
export internals to user-space.
- R-Car Gen3 SoCs support for the ipmmu-vmsa driver
- The ARM-SMMU now aborts transactions from unknown devices and devices
not attached to any domain.
- Various cleanups and smaller fixes all over the place.
* tag 'iommu-updates-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (42 commits)
iommu/omap: Fix cache flushes on L2 table entries
iommu: Remove the ->map_sg indirection
iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel
iommu/arm-smmu-v3: Prevent any devices access to memory without registration
iommu/ipmmu-vmsa: Don't register as BUS IOMMU if machine doesn't have IPMMU-VMSA
iommu/ipmmu-vmsa: Clarify supported platforms
iommu/ipmmu-vmsa: Fix allocation in atomic context
iommu: Add config option to set passthrough as default
iommu: Add sysfs attribyte for domain type
iommu/arm-smmu-v3: sync the OVACKFLG to PRIQ consumer register
iommu/arm-smmu: Error out only if not enough context interrupts
iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE
iommu/io-pgtable-arm: Fix pgtable allocation in selftest
iommu/vt-d: Remove the obsolete per iommu pasid tables
iommu/vt-d: Apply per pci device pasid table in SVA
iommu/vt-d: Allocate and free pasid table
iommu/vt-d: Per PCI device pasid table interfaces
iommu/vt-d: Add for_each_device_domain() helper
iommu/vt-d: Move device_domain_info to header
iommu/vt-d: Apply global PASID in SVA
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Add Daniel Lezcano as the reviewer of thermal framework and SoC
driver changes (Daniel Lezcano).
- Fix a bug in intel_dts_soc_thermal driver, which does not translate
IO-APIC GSI (Global System Interrupt) into Linux irq number (Hans de
Goede).
- For device tree bindings, allow cooling devices sharing same trip
point with same contribution value to share cooling map (Viresh
Kumar).
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
dt-bindings: thermal: Allow multiple devices to share cooling map
MAINTAINERS: Add Daniel Lezcano as designated reviewer for thermal
Thermal: Intel SoC DTS: Translate IO-APIC GSI number to linux irq number
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor
Pull apparmor updates from John Johansen:
"There is nothing major this time just four bug fixes and a patch to
remove some dead code:
Cleanups:
- remove no-op permission check in policy_unpack
Bug fixes:
- fix an error code in __aa_create_ns()
- fix failure to audit context info in build_change_hat
- check buffer bounds when mapping permissions mask
- fully initialize aa_perms struct when answering userspace query"
* tag 'apparmor-pr-2018-08-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: remove no-op permission check in policy_unpack
apparmor: fix an error code in __aa_create_ns()
apparmor: Fix failure to audit context info in build_change_hat
apparmor: Fully initialize aa_perms struct when answering userspace query
apparmor: Check buffer bounds when mapping permissions mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- An implementation for the newly added hv_ops->flush() for the OPAL
hvc console driver backends, I forgot to apply this after merging the
hvc driver changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when
multiple children of a bridge try to enable it simultaneously. This
is a workaround until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause
broken scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9
due to a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some
bugs which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to: Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy,
Hari Bathini, Luke Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul
Mackerras, Srikar Dronamraju.
* tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mce: Fix SLB rebolting during MCE recovery path.
KVM: PPC: Book3S: Fix guest DMA when guest partially backed by THP pages
powerpc/mm/radix: Only need the Nest MMU workaround for R -> RW transition
powerpc/mm/books3s: Add new pte bit to mark pte temporarily invalid.
powerpc/nohash: fix pte_access_permitted()
powerpc/topology: Get topology for shared processors at boot
powerpc64/ftrace: Include ftrace.h needed for enable/disable calls
powerpc/powernv/pci: Work around races in PCI bridge enabling
powerpc/fadump: cleanup crash memory ranges support
powerpc/powernv: provide a console flush operation for opal hvc driver
powerpc/traps: Avoid rate limit messages from show unhandled signals
powerpc/64s: Fix PACA_IRQ_HARD_DIS accounting in idle_power4()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- A couple of patches for the zcrypt driver:
+ Add two masks to determine which AP cards and queues are host
devices, this will be useful for KVM AP device passthrough
+ Add-on patch to improve the parsing of the new apmask and aqmask
+ Some code beautification
- Second try to reenable the GCC plugins, the first patch set had a
patch to do this but the merge somehow missed this
- Remove the s390 specific GCC version check and use the generic one
- Three patches for kdump, two bug fixes and one cleanup
- Three patches for the PCI layer, one bug fix and two cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: remove gcc version check (4.3 or newer)
s390/zcrypt: hex string mask improvements for apmask and aqmask.
s390/zcrypt: AP bus support for alternate driver(s)
s390/zcrypt: code beautify
s390/zcrypt: switch return type to bool for ap_instructions_available()
s390/kdump: Remove kzalloc_panic
s390/kdump: Fix memleak in nt_vmcoreinfo
s390/kdump: Make elfcorehdr size calculation ABI compliant
s390/pci: remove fmb address from debug output
s390/pci: remove stale rc
s390/pci: fix out of bounds access during irq setup
s390/zcrypt: fix ap_instructions_available() returncodes
s390: reenable gcc plugins for real
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI Kconfig fix from Rafael Wysocki:
"Fix recent menuconfig breakage causing it to present ACPI-specific
options incorrectly (Arnd Bergmann)"
* tag 'acpi-4.19-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: fix menuconfig presentation of ACPI submenu
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace fixes from Eric Biederman:
"This is a set of four fairly obvious bug fixes:
- a switch from d_find_alias to d_find_any_alias because the xattr
code perversely takes a dentry
- two mutex vs copy_to_user fixes from Jann Horn
- a fix to use a sanitized size not the size userspace passed in from
Christian Brauner"
* 'userns-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
getxattr: use correct xattr length
sys: don't hold uts_sem while accessing userspace memory
userns: move user access out of the mutex
cap_inode_getsecurity: use d_find_any_alias() instead of d_find_alias()
|
|
Pull drm fixes from Dave Airlie:
"Just a couple of fixes"
One MAINTAINERS address change, two panels fixes, and set of amdgpu
fixes (build fixes, display fixes and some others)"
* tag 'drm-next-2018-08-24' of git://anongit.freedesktop.org/drm/drm:
drm/edid: Add 6 bpc quirk for SDC panel in Lenovo B50-80
drm/amd/display: Don't build DCN1 when kcov is enabled
Revert "drm/amdgpu/display: Replace CONFIG_DRM_AMD_DC_DCN1_0 with CONFIG_X86"
drm/amdgpu/display: disable eDP fast boot optimization on DCE8
drm/amdgpu: fix amdgpu_amdkfd_remove_eviction_fence v3
drm/amdgpu: fix incorrect use of drm_file->pid
drm/amdgpu: fix incorrect use of fcheck
drm/powerplay: enable dpm under pass-through
drm/amdgpu: access register without KIQ
drm/amdgpu: set correct base for THM/NBIF/MP1 IP
drm/amd/display: fix dentist did ranges
drm/amd/display: make dp_ss_off optional
drm/amd/display: fix dp_ss_control vbios flag parsing
drm/amd/display: Do not retain link settings
MAINTAINERS: drm-misc: Change seanpaul's email address
drm/panel: simple: tv123wam: Add unprepare delay
|
|
Used wrong pp interface, the original interface is
exposed by dpm on SI and paritial CI.
Pointed out by Francis David <david.francis@amd.com>
v2: dal only need to set min_dcefclk and min_fclk to smu.
so use display_clock_voltage_request interface,
instand of update all display configuration.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull second i2c update from Wolfram Sang:
"As promised, here is my 2nd pull request for I2C, containing:
- removal of the attach_adapter callback, converting its last user
- removal of any __deprecated usage within I2C
- one email address update
- some SPDX conversion"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: don't use any __deprecated handling anymore
i2c: use SPDX identifier for Renesas drivers
i2c: ocores: update my email address
i2c: remove deprecated attach_adapter callback
macintosh: therm_windtunnel: drop using attach_adapter
|
|
Commit 9b10df596bd4 ("i40e: use WARN_ONCE to replace the commented
BUG_ON size check") introduced a warning check to make sure
that the size of the stat strings was always the expected value. This
code accidentally inverted the check of the data pointer. Fix this so
that we accurately count the size of the stats we copied in.
This fixes an erroneous WARN kernel splat that occurs when requesting
ethtool statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If interface is connected to switch port configured for DCB there are
TX timeouts when bringing up interface. Problem started appearing after
adding in i40e driver code mqprio hardware offload mode. In function
i40e_vsi_configure_bw_alloc was added resetting BW rate which should
be executing when mqprio qdisc is removed but was also when there was
no mqprio qdisc added and DCB was enabled. In this patch was added
additional check for DCB flag so now when DCB is enabled the correct
DCB configs from before mqprio patch are restored.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since VFLR doesn't clear VFMBMEM (VF Mailbox Memory)
and is not re-enabling queues correctly we should fix
this behavior.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
These changes address comments by Jakub Kicinski on
commit 38b7e7f8ae82 ("ixgbe: Do not allow LRO or MTU change with XDP").
Change the MTU check with XDP to allow any supported value and only
reject those outside of the range as opposed to rejecting any change
when XDP is active. In situations where MTU size is not supported,
return -EINVAL instead of -EPERM.
Add checks when enabling SRIOV, DCB, or adding L2FW offloaded device
as they are not supported with XDP.
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ixgbe_fcoe_ddp_setup(), ixgbe_setup_fcoe_ddp_resources() and
ixgbe_sw_init() are never called in atomic context.
They call kmalloc(), dma_pool_alloc() and kzalloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igb_integrated_phy_loopback() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igb_sw_init() is never called in atomic context.
It calls kzalloc() and kcalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On i210, Launchtime (TxTime) requires the usage of an "Advanced
Transmit Context Descriptor" for retrieving the timestamp of a packet.
The igb driver correctly builds such descriptor on the segmentation
flow (i.e. igb_tso()) or on the checksum one (i.e. igb_tx_csum()), but the
feature is broken for AF_PACKET if the IGB_TX_FLAGS_VLAN is not set,
which happens due to an early return on igb_tx_csum().
This flag is only set by the kernel when a VLAN interface is used,
thus we can't just rely on it. Here we are fixing this issue by checking
if launchtime is enabled for the current tx_ring before performing the
early return.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Enabling the interrupt early, before power has been applied to the
device, can result in an interrupt being delivered too early if:
- the IOMMU shares an interrupt with a VOP
- the VOP has a pending interrupt (after a kexec, for example)
In these conditions, we end-up taking the interrupt without
the IOMMU being ready to handle the interrupt (not powered on).
Moving the interrupt request past the pm_runtime_enable() call
makes sure we can at least access the IOMMU registers. Note that
this is only a partial fix, and that the VOP interrupt will still
be screaming until the VOP driver kicks in, which advocates for
a more synchronized interrupt enabling/disabling approach.
Fixes: 0f181d3cf7d98 ("iommu/rockchip: Add runtime PM support")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
