| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fix from Damien Le Moal:
"A single fix from me to correctly handle the size of read-only zone
files"
* tag 'zonefs-5.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonfs: Fix handling of read-only zones
|
|
Add Intel Comet Lake PCH-V PCI ID to the list of supported controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add Intel Comet Lake PCH-H PCI ID to the list of supported controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When we spawn a SCSI device from an ATA device in libata-scsi
the SCSI device had no relation to the device tree.
The DT binding allows us to define port nodes under a
PATA (IDE) or SATA host controller, so we can have proper device
nodes for these devices.
If OF is enabled, walk the children of the host controller node
to see if there is a valid device tree node to assign. The reg
is used to match to ID 0 for the master device and ID 1 for the
slave device.
The corresponding device tree bindings have been accepted by
the device tree maintainers.
Cc: Chris Healy <cphealy@gmail.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If the call to scsi_add_host_with_dma() in ata_scsi_add_hosts() fails,
then we may get use-after-free KASAN warns:
==================================================================
BUG: KASAN: use-after-free in kobject_put+0x24/0x180
Read of size 1 at addr ffff0026b8c80364 by task swapper/0/1
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 5.6.0-rc3-00004-g5a71b206ea82-dirty #1765
Hardware name: Huawei TaiShan 200 (Model 2280)/BC82AMDD, BIOS 2280-V2 CS V3.B160.01 02/24/2020
Call trace:
dump_backtrace+0x0/0x298
show_stack+0x14/0x20
dump_stack+0x118/0x190
print_address_description.isra.9+0x6c/0x3b8
__kasan_report+0x134/0x23c
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
kobject_put+0x24/0x180
put_device+0x10/0x20
scsi_host_put+0x10/0x18
ata_devres_release+0x74/0xb0
release_nodes+0x2d0/0x470
devres_release_all+0x50/0x78
really_probe+0x2d4/0x560
driver_probe_device+0x7c/0x148
device_driver_attach+0x94/0xa0
__driver_attach+0xa8/0x110
bus_for_each_dev+0xe8/0x158
driver_attach+0x30/0x40
bus_add_driver+0x220/0x2e0
driver_register+0xbc/0x1d0
__pci_register_driver+0xbc/0xd0
ahci_pci_driver_init+0x20/0x28
do_one_initcall+0xf0/0x608
kernel_init_freeable+0x31c/0x384
kernel_init+0x10/0x118
ret_from_fork+0x10/0x18
Allocated by task 5:
save_stack+0x28/0xc8
__kasan_kmalloc.isra.8+0xbc/0xd8
kasan_kmalloc+0xc/0x18
__kmalloc+0x1a8/0x280
scsi_host_alloc+0x44/0x678
ata_scsi_add_hosts+0x74/0x268
ata_host_register+0x228/0x488
ahci_host_activate+0x1c4/0x2a8
ahci_init_one+0xd18/0x1298
local_pci_probe+0x74/0xf0
work_for_cpu_fn+0x2c/0x48
process_one_work+0x488/0xc08
worker_thread+0x330/0x5d0
kthread+0x1c8/0x1d0
ret_from_fork+0x10/0x18
Freed by task 5:
save_stack+0x28/0xc8
__kasan_slab_free+0x118/0x180
kasan_slab_free+0x10/0x18
slab_free_freelist_hook+0xa4/0x1a0
kfree+0xd4/0x3a0
scsi_host_dev_release+0x100/0x148
device_release+0x7c/0xe0
kobject_put+0xb0/0x180
put_device+0x10/0x20
scsi_host_put+0x10/0x18
ata_scsi_add_hosts+0x210/0x268
ata_host_register+0x228/0x488
ahci_host_activate+0x1c4/0x2a8
ahci_init_one+0xd18/0x1298
local_pci_probe+0x74/0xf0
work_for_cpu_fn+0x2c/0x48
process_one_work+0x488/0xc08
worker_thread+0x330/0x5d0
kthread+0x1c8/0x1d0
ret_from_fork+0x10/0x18
There is also refcount issue, as well:
WARNING: CPU: 1 PID: 1 at lib/refcount.c:28 refcount_warn_saturate+0xf8/0x170
The issue is that we make an erroneous extra call to scsi_host_put()
for that host:
So in ahci_init_one()->ata_host_alloc_pinfo()->ata_host_alloc(), we setup
a device release method - ata_devres_release() - which intends to release
the SCSI hosts:
static void ata_devres_release(struct device *gendev, void *res)
{
...
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
if (!ap)
continue;
if (ap->scsi_host)
scsi_host_put(ap->scsi_host);
}
...
}
However in the ata_scsi_add_hosts() error path, we also call
scsi_host_put() for the SCSI hosts.
Fix by removing the the scsi_host_put() calls in ata_scsi_add_hosts() and
leave this to ata_devres_release().
Fixes: f31871951b38 ("libata: separate out ata_host_alloc() and ata_host_register()")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add the PCI ID to the driver list to support this new device.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Calls to dma_map_sg may return less segments / entries than requested
if they fall on page bounderies. The old implementation did not
support this use case.
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206461
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206895
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1056
Signed-off-by: Shane Francis <bigbeeshane@gmail.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325090741.21957-4-bigbeeshane@gmail.com
Cc: stable@vger.kernel.org
|
|
Calls to dma_map_sg may return less segments / entries than requested
if they fall on page bounderies. The old implementation did not
support this use case.
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206461
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206895
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1056
Signed-off-by: Shane Francis <bigbeeshane@gmail.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325090741.21957-3-bigbeeshane@gmail.com
Cc: stable@vger.kernel.org
|
|
As dma_map_sg can reorganize scatter-gather lists in a
way that can cause some later segments to be empty we should
always use the sg_dma_len macro to fetch the actual length.
This could now be 0 and not need to be mapped to a page or
address array
Fixes: be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206461
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206895
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1056
Signed-off-by: Shane Francis <bigbeeshane@gmail.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325090741.21957-2-bigbeeshane@gmail.com
Cc: stable@vger.kernel.org
|
|
These macros are just used by a few files. Move them out of genhd.h,
which is included everywhere into a new standalone header.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
None of this needs to be exposed to drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This is bio layer functionality and not related to buffer heads.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
get_gendisk is not used by any modular code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
disk_map_sector_rcu is not used by any modular code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
disk_get_part is not used by any modular code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Factor out the requeue handling from the dispatch code, this will make
subsequent addition of different requeueing schemes easier.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Column "time_in_queue" in diskstats is supposed to show total waiting time
of all requests. I.e. value should be equal to the sum of times from other
columns. But this is not true, because column "time_in_queue" is counted
separately in jiffies rather than in nanoseconds as other times.
This patch removes redundant counter for "time_in_queue" and shows total
time of read, write, discard and flush requests.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Reading /proc/diskstats iterates over all cpus for summing each field.
It's faster to sum all fields in one pass.
Hammering /proc/diskstats with fio shows 2x performance improvement:
fio --name=test --numjobs=$JOBS --filename=/proc/diskstats \
--size=1k --bs=1k --fallocate=none --create_on_open=1 \
--time_based=1 --runtime=10 --invalidate=0 --group_report
JOBS=1 JOBS=10
Before: 7k iops 64k iops
After: 18k iops 120k iops
Also this way code is more compact:
add/remove: 1/0 grow/shrink: 0/2 up/down: 194/-1540 (-1346)
Function old new delta
part_stat_read_all - 194 +194
diskstats_show 1344 631 -713
part_stat_show 1219 392 -827
Total: Before=14966947, After=14965601, chg -0.01%
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently io_ticks is approximated by adding one at each start and end of
requests if jiffies counter has changed. This works perfectly for requests
shorter than a jiffy or if one of requests starts/ends at each jiffy.
If disk executes just one request at a time and they are longer than two
jiffies then only first and last jiffies will be accounted.
Fix is simple: at the end of request add up into io_ticks jiffies passed
since last update rather than just one jiffy.
Example: common HDD executes random read 4k requests around 12ms.
fio --name=test --filename=/dev/sdb --rw=randread --direct=1 --runtime=30 &
iostat -x 10 sdb
Note changes of iostat's "%util" 8,43% -> 99,99% before/after patch:
Before:
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sdb 0,00 0,00 82,60 0,00 330,40 0,00 8,00 0,96 12,09 12,09 0,00 1,02 8,43
After:
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sdb 0,00 0,00 82,50 0,00 330,00 0,00 8,00 1,00 12,10 12,10 0,00 12,12 99,99
Now io_ticks does not loose time between start and end of requests, but
for queue-depth > 1 some I/O time between adjacent starts might be lost.
For load estimation "%util" is not as useful as average queue length,
but it clearly shows how often disk queue is completely empty.
Fixes: 5b18b5a73760 ("block: delete part_round_stats and switch to less precise counting")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Correct the probe return value to -ENODEV on non-Exynos platforms.
Link: https://lore.kernel.org/r/20200316175652.5604-4-krzk@kernel.org
Fixes: 02fb29882d5c ("soc: samsung: chipid: Drop "syscon" compatible requirement")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
tee: amdtee: out of bounds read in find_session()
* tag 'tee-amdtee-fix2-for-5.6' of https://git.linaro.org/people/jens.wiklander/linux-tee:
tee: amdtee: out of bounds read in find_session()
Link: https://lore.kernel.org/r/20200320063446.GA9892@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/narmstrong/linux-oxnas into arm/fixes
- interrupt controller mask init fix to avoid spurious irq after soft reset
* tag 'oxnas-arm-soc-dt-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/narmstrong/linux-oxnas:
ARM: dts: oxnas: Fix clear-mask property
Link: https://lore.kernel.org/r/1cc83d6b-78de-9160-59bf-77cfe726a365@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.6, please pull the following:
- Nick fixes the missing pinctrl-names property for the Raspberry Pi
Zero Wireless DTS
- Nicolas fixes the VC4 firmware node dma-range property which does not
have the limitations of the soc's bus node
* tag 'arm-soc/for-5.6/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
Link: https://lore.kernel.org/r/20200323025246.22713-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These two device trees were either missed or added after
the commit correcting the "entry-method" from
"arm,psci" to just "psci" as per the binding.
Link: https://lore.kernel.org/r/20200322115846.16265-1-linus.walleij@linaro.org
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few more fixes for omaps
Just few dts fixes:
- A fix droid4 touchscreen stopping working with lost gpio interrupts
- Also limit omap5 dma range similar to what we've recently done for dra7
* tag 'omap-for-v5.6/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: dts: N900: fix onenand timings
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
Link: https://lore.kernel.org/r/pull-1584575254-461940@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit d4ec0cb05064 ("ARM: dts: exynos: Add support for the
touch-sensitive buttons on Midas family") added a new fixed regulator
("voltage-regulator-6") to base "midas" .dtsi, but it didn't update the
clients of that .dtsi, which define their own fixed regulators starting
from the "voltage-regulator-6". This results in aliasing of the regulator
dt nodes and breaks operation of OLED panel due to lack of power supply.
Fix this by increasing the numbers in the fixed regulator names for those
boards.
Link: https://lore.kernel.org/r/20200316173710.3144-1-krzk@kernel.org
Fixes: d4ec0cb05064 ("ARM: dts: exynos: Add support for the touch-sensitive buttons on Midas family")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.6, round 2:
- Fix minimum voltage setting of vdd_arm and vdd_soc on i.MX6
phycore-som board.
* tag 'imx-fixes-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
Link: https://lore.kernel.org/r/20200316032555.GD17221@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
It has been discovered that this feature can globally block the RX port,
so it should be allowed for highly privileged users only.
Fixes: 03404e8ae652("IB/mlx5: Add support to dropless RQ")
Link: https://lore.kernel.org/r/20200322124906.1173790-1-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.6 - part 2
This follows up on the previous 5.6 fixes tag with a fix for the A33
Security System (crypto offloading hardware). The hardware was found
to not be compatible with existing hardware and a new compatible was
needed.
The driver change was picked up right before the previous -rc6 and
the DT bindings and DT changes were not picked up. The goal is to have
all the changes in the same release, that is v5.6.
* tag 'sunxi-fixes-for-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a33: add the new SS compatible
dt-bindings: crypto: add new compatible for A33 SS
Link: https://lore.kernel.org/r/20200313060727.GA23962@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for v5.6
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
* tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
bus: sunxi-rsb: Return correct data when mixing 16-bit and 8-bit reads
ARM: dts: sun8i-a83t-tbs-a711: Fix USB OTG mode detection
ARM: dts: sun8i-a83t-tbs-a711: HM5065 doesn't like such a high voltage
ARM: dts: sun8i: a83t: Fix incorrect clk and reset macros for EMAC device
Link: https://lore.kernel.org/r/20200313055233.GA19649@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/fixes
NXP/FSL soc driver fixes for v5.6
DPAA2 DPIO
- Fix a kernel hang caused by irq requested before creating dpio
* tag 'soc-fsl-fix-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: dpio: register dpio irq handlers after dpio create
Link: https://lore.kernel.org/r/20200312202525.16708-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The he_sr_control field is just a u8, so le32_to_cpu()
shouldn't be applied to it; this was evidently copied
from ieee80211_he_oper_size(). Fix it, and also adjust
the type of the local variable.
Fixes: ef11a931bd1c ("mac80211: HE: add Spatial Reuse element parsing support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200325090918.dfe483b49e06.Ia53622f23b2610a2ae6ea39a199866196fe946c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The new opmode notification used this attribute with a u8, when
it's documented as a u32 and indeed used in userspace as such,
it just happens to work on little-endian systems since userspace
isn't doing any strict size validation, and the u8 goes into the
lower byte. Fix this.
Cc: stable@vger.kernel.org
Fixes: 466b9936bf93 ("cfg80211: Add support to notify station's opmode change to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200325090531.be124f0a11c7.Iedbf4e197a85471ebd729b186d5365c0343bf7a8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The missing 'return' work may make it hard for other developers to
understand it.
Signed-off-by: Chucheng Luo <luochucheng@vivo.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some USB bridge devices will return a default set of characteristics during
initialization. And then, once an attached drive has spun up, substitute
the actual parameters reported by the drive. According to the SCSI spec,
the device should return a UNIT ATTENTION in case any reported parameters
change. But in this case the change is made silently after a small window
where default values are reported.
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of
physical block size") validated the reported optimal I/O size against the
physical block size to overcome problems with devices reporting nonsensical
transfer sizes. However, this validation did not account for the fact that
aforementioned devices will return default values during a brief window
during spin-up. The subsequent change in reported characteristics would
invalidate the checking that had previously been performed.
Unset a previously configured optimal I/O size should the sanity checking
fail on subsequent revalidate attempts.
Link: https://lore.kernel.org/r/33fb522e-4f61-1b76-914f-c9e6a3553c9b@gmail.com
Cc: Bryan Gurney <bgurney@redhat.com>
Cc: <stable@vger.kernel.org>
Reported-by: Bernhard Sulzer <micraft.b@gmail.com>
Tested-by: Bernhard Sulzer <micraft.b@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The write pointer of zones in the read-only consition is defined as
invalid by the SCSI ZBC and ATA ZAC specifications. It is thus not
possible to determine the correct size of a read-only zone file on
mount. Fix this by handling read-only zones in the same manner as
offline zones by disabling all accesses to the zone (read and write)
and initializing the inode size of the read-only zone to 0).
For zones found to be in the read-only condition at runtime, only
disable write access to the zone and keep the size of the zone file to
its last updated value to allow the user to recover previously written
data.
Also fix zonefs documentation file to reflect this change.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
|
|
Commit 253a99d95d5b ("bcache: move macro btree() and btree_root()
into btree.h") makes two duplicated declaration into btree.h,
typedef int (btree_map_keys_fn)();
int bch_btree_map_keys();
The kbuild test robot <lkp@intel.com> detects and reports this
problem and this patch fixes it by removing the duplicated ones.
Fixes: 253a99d95d5b ("bcache: move macro btree() and btree_root() into btree.h")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) A new selftest for nf_queue, from Florian Westphal. This test
covers two recent fixes: 07f8e4d0fddb ("tcp: also NULL skb->dev
when copy was needed") and b738a185beaa ("tcp: ensure skb->dev is
NULL before leaving TCP stack").
2) The fwd action breaks with ifb. For safety in next extensions,
make sure the fwd action only runs from ingress until it is extended
to be used from a different hook.
3) The pipapo set type now reports EEXIST in case of subrange overlaps.
Update the rbtree set to validate range overlaps, so far this
validation is only done only from userspace. From Stefano Brivio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-24
This series introduces some fixes to mlx5 driver.
From Aya, Fixes to the RX error recovery flows
From Leon, Fix IB capability mask
Please pull and let me know if there is any problem.
For -stable v5.5
('net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure')
For -stable v5.4
('net/mlx5e: Fix ICOSQ recovery flow with Striding RQ')
('net/mlx5e: Do not recover from a non-fatal syndrome')
('net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset')
('net/mlx5e: Enhance ICOSQ WQE info fields')
The above patch ('net/mlx5e: Enhance ICOSQ WQE info fields')
will fail to apply cleanly on v5.4 due to a trivial contextual conflict,
but it is an important fix, do I need to do something about it or just
assume Greg will know how to handle this ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7b4 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DT binding for this PHY describes an *optional* clock property.
Due to a bug in the error handling logic, we are actually ignoring this
clock *all* of the time so far.
Fix this by using devm_clk_get_optional() to handle this clock properly.
Fixes: b78ac6ecd1b6b ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb4_ptp_fineadjtime() doesn't pass the signedness of offset delta
in FW_PTP_CMD. Fix it by passing correct sign.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: d461933638ae ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the software CBS does not consider the packet sending time
when depleting the credits. It caused the throughput to be
Idleslope[kbps] * (Port transmit rate[kbps] / |Sendslope[kbps]|) where
Idleslope * (Port transmit rate / (Idleslope + |Sendslope|)) = Idleslope
is expected. In order to fix the issue above, this patch takes the time
when the packet sending completes into account by moving the anchor time
variable "last" ahead to the send completion time upon transmission and
adding wait when the next dequeue request comes before the send
completion time of the previous packet.
changelog:
V2->V3:
- remove unnecessary whitespace cleanup
- add the checks if port_rate is 0 before division
V1->V2:
- combine variable "send_completed" into "last"
- add the comment for estimate of the packet sending
Fixes: 585d763af09c ("net/sched: Introduce Credit Based Shaper (CBS) qdisc")
Signed-off-by: Zh-yuan Ye <ye.zh-yuan@socionext.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 19ba1eb15a2a ("Input: psmouse - add a custom serio protocol
to send extra information") introduced usage of the BIT() macro
for SERIO_* flags; this macro is not provided in UAPI headers.
Replace if with similarly defined _BITUL() macro defined
in <linux/const.h>.
Fixes: 19ba1eb15a2a ("Input: psmouse - add a custom serio protocol to send extra information")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Cc: <stable@vger.kernel.org> # v5.0+
Link: https://lore.kernel.org/r/20200324041341.GA32335@asgard.redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The main difference between send and receive SW completions is related to
separate treatment of WQ queue. For receive completions, the initial index
to be flushed is stored in "tail", while for send completions, it is in
deleted "last_poll".
CPU: 54 PID: 53405 Comm: kworker/u161:0 Kdump: loaded Tainted: G OE --------- -t - 4.18.0-147.el8.ppc64le #1
Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core]
NIP: c000003c7c00a000 LR: c00800000e586af4 CTR: c000003c7c00a000
REGS: c0000036cc9db940 TRAP: 0400 Tainted: G OE --------- -t - (4.18.0-147.el8.ppc64le)
MSR: 9000000010009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 24004488 XER: 20040000
CFAR: c00800000e586af0 IRQMASK: 0
GPR00: c00800000e586ab4 c0000036cc9dbbc0 c00800000e5f1a00 c0000037d8433800
GPR04: c000003895a26800 c0000037293f2000 0000000000000201 0000000000000011
GPR08: c000003895a26c80 c000003c7c00a000 0000000000000000 c00800000ed30438
GPR12: c000003c7c00a000 c000003fff684b80 c00000000017c388 c00000396ec4be40
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: c00000000151e498 0000000000000010 c000003895a26848 0000000000000010
GPR24: 0000000000000010 0000000000010000 c000003895a26800 0000000000000000
GPR28: 0000000000000010 c0000037d8433800 c000003895a26c80 c000003895a26800
NIP [c000003c7c00a000] 0xc000003c7c00a000
LR [c00800000e586af4] __ib_process_cq+0xec/0x1b0 [ib_core]
Call Trace:
[c0000036cc9dbbc0] [c00800000e586ab4] __ib_process_cq+0xac/0x1b0 [ib_core] (unreliable)
[c0000036cc9dbc40] [c00800000e586c88] ib_cq_poll_work+0x40/0xb0 [ib_core]
[c0000036cc9dbc70] [c000000000171f44] process_one_work+0x2f4/0x5c0
[c0000036cc9dbd10] [c000000000172a0c] worker_thread+0xcc/0x760
[c0000036cc9dbdc0] [c00000000017c52c] kthread+0x1ac/0x1c0
[c0000036cc9dbe30] [c00000000000b75c] ret_from_kernel_thread+0x5c/0x80
Fixes: 8e3b68830186 ("RDMA/mlx5: Delete unreachable handle_atomic code by simplifying SW completion")
Link: https://lore.kernel.org/r/20200318091640.44069-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The following modify sequence (loosely based on ipoib) will lose a pkey
modifcation:
- Modify (pkey index, port)
- Modify (new pkey index, NO port)
After the first modify, the qp_pps list will have saved the pkey and the
unit on the main list.
During the second modify, get_new_pps() will fetch the port from qp_pps
and read the new pkey index from qp_attr->pkey_index. The state will
still be zero, or IB_PORT_PKEY_NOT_VALID. Because of the invalid state,
the new values will never replace the one in the qp pps list, losing the
new pkey.
This happens because the following if statements will never correct the
state because the first term will be false. If the code had been executed,
it would incorrectly overwrite valid values.
if ((qp_attr_mask & IB_QP_PKEY_INDEX) && (qp_attr_mask & IB_QP_PORT))
new_pps->main.state = IB_PORT_PKEY_VALID;
if (!(qp_attr_mask & (IB_QP_PKEY_INDEX | IB_QP_PORT)) && qp_pps) {
new_pps->main.port_num = qp_pps->main.port_num;
new_pps->main.pkey_index = qp_pps->main.pkey_index;
if (qp_pps->main.state != IB_PORT_PKEY_NOT_VALID)
new_pps->main.state = IB_PORT_PKEY_VALID;
}
Fix by joining the two if statements with an or test to see if qp_pps is
non-NULL and in the correct state.
Fixes: 1dd017882e01 ("RDMA/core: Fix protection fault in get_pkey_idx_qp_list")
Link: https://lore.kernel.org/r/20200313124704.14982.55907.stgit@awfm-01.aw.intel.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Zhu Yanjun contributed many patches to RXE and expressed genuine interest
in improve RXE even more. Let's add him as a maintainer.
Link: https://lore.kernel.org/r/20200312083658.29603-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
