| Age | Commit message (Collapse) | Author |
|---|
|
TL4 calculation for a given SQ of secondary Qsets is incorrect
and goes out of bounds and also for some SQ's TL4 chosen will
transmit data via a different BGX interface and not same as
primary Qset's interface.
This patch fixes this issue.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for SMU RX local/remote faults along with SPU LINK
status. Otherwise at times link is UP at our end but DOWN
at link partner's side. Also due to an issue in BGX it's
rarely seen that initialization doesn't happen properly
and SMU RX reports faults with everything fine at SPU.
This patch tries to reinitialize LMAC to fix it.
Also fixed LMAC disable sequence to properly bring down link.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Tao Wang <tao.wang@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes#2 for 4.7-rc
The following series provides one-liners fixes for mlx5 driver plus one
medium patch to reorganize ethtool counters reporting.
Highlights:
- Added MODIFY_FLOW_TABLE to command strings table
- Add ConnectX-5 PCIe 4.0 to list of supported devices
- Rename ASYNC_EVENTS enum
- Enable BlueFlame only when supported by device
- Avoid adding same vxlan port twice
- Report the correct number of PFC counters
- Reorganize ethtool reported counters and remove duplications
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Categorize and reorganize ethtool statistics counters by renaming to
"rx_*" and "tx_*" and removing redundant and duplicated counters, this
way they are easier to grasp and more user friendly.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Number of PFC counters used to count only number of priorities with PFC
enabled, but each priority has more than one counter, hence the need to
multiply it by the number of PFC counters per priority.
Fixes: cf678570d5a1 ('net/mlx5e: Add per priority group to PPort counters')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not allow the same vxlan udp port to be added to the device more than
once.
Fixes: b3f63c3d5e2c ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous to this patch mapping was always set to write combining without
checking whether BlueFlame is supported in the device.
Fixes: 0ba422410bbf ('net/mlx5: Fix global UAR mapping')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change MLX5E_STATE_ASYNC_EVENTS_ENABLE to
MLX5E_STATE_ASYNC_EVENTS_ENABLED since it represent a state and not an
operation.
Fixes: acff797cd1874 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the upcoming ConnectX-5 PCIe 4.0 device to the list of
supported devices by the mlx5 driver.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add command string for MODIFY_FLOW_TABLE which is used by the driver.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
Due to the relatively long 10ms timeout, probably this didn't cause any
real problems, but fix it in any case for consistency.
Fixes: 0351b93992aa ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-5-git-send-email-imre.deak@intel.com
(cherry picked from commit 713a6b668932213247b394559bc229cd0fec2777)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
Fixes: 0351b93992aa ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-4-git-send-email-imre.deak@intel.com
(cherry picked from commit f53dd63f1119a98a16d1a5a7cb3277a2f1ff483d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
Fixes: 0351b93992aa ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-3-git-send-email-imre.deak@intel.com
(cherry picked from commit cf3598c23cd09d5f063fa8c12fe9ddd5a352d3d5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Since wait_for_atomic doesn't re-check the wait-for condition after
expiry of the timeout it can fail when called from non-atomic context
even if the condition is set correctly before the expiry. Fix this by
using the non-atomic wait_for instead.
I noticed this via the PLL locking timing out incorrectly, with this fix
I couldn't reproduce the problem.
Fixes: 0351b93992aa ("drm/i915: Do not lie about atomic timeout granularity")
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
CC: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1467110253-16046-2-git-send-email-imre.deak@intel.com
(cherry picked from commit 0b786e41c73956126f6297764459021deef8aba7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
During hibernation the cached DP port register value will be left with
whatever value we have there when we create the hibernation image.
Currently that means the port (and eDP PLL) will be off in the cached
value. However when we resume there is no guarantee that the value
in the actual register will match the cached value. If i915 isn't
loaded in the kernel that loads the hibernation image, the port may
well be on (eg. left on by the BIOS). The encoder state readout
does the right thing in this case and updates our encoder state
to reflect the actual hardware state. However the post-resume modeset
will then use the stale cached port register value in
intel_dp_link_down() and potentially confuse the hardware.
This was caught by the following assert
WARNING: CPU: 3 PID: 5288 at ../drivers/gpu/drm/i915/intel_dp.c:2184 assert_edp_pll+0x99/0xa0 [i915]
eDP PLL state assertion failure (expected on, current off)
on account of the eDP PLL getting prematurely turned off when
shutting down the port, since the DP_PLL_ENABLE bit wasn't set
in the cached register value.
Presumably I introduced this problem in
commit 6fec76628333 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
as before that we didn't update the cached value after shuttting the
port down. That's assuming the port got enabled at least once prior
to hibernating. If that didn't happen then the cached value would
still have been totally out of sync with reality (eg. first boot w/o
eDP on, then hibernate, and then resume with eDP on).
So, let's fix this properly and refresh the cached register value from
the hardware register during resume.
DDI platforms shouldn't use the cached value during port disable at
least, so shouldn't have this particular issue. They might still have
issues if we skip the initial modeset and then try to retrain the link
or something. But untangling this DP vs. DDI mess is a bigger topic,
so let's jut punt on DDI for now.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Fixes: 6fec76628333 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463162036-27931-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 64989ca4b27acb026b6496ec21e43bee66f86a5b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Marvell 88E1111 currently uses the generic marvell config ANEG function.
This function has a sequence accessing Page 5 and Register 31,
both of which are not defined or reserved for this PHY.
Hence this patch adds a new config ANEG function for Marvell 88E1111
without these erroneous accesses.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sven Eckelmann says:
====================
batman-adv: Fixes for Linux 4.7
Antonio currently seems to be occupied. This is currently rather unfortunate
because there are patches waiting in the batman-adv development repository
maint(enance) branch [1] since up to 6 weeks. I am now getting asked when
these patches will hit the distribution kernels and therefore decided to
submit these patches directly to netdev.
The patch from Simon works around the problem that warnings could be triggered
in the translation table code via packets using a VLAN not configured on the
target host. This warning was replaced with a rate limited info message.
Ben Hutchings found an superfluous batadv_softif_vlan_put in the error
handling code of the translation table while he backported the "batman-adv:
Fix reference counting of vlan object for tt_local_entry" patch to the stable
kernels. He noticed correctly that this batadv_softif_vlan_put should also
have been removed by the said patch.
The most requested fix at the moment is related to a double free in the
translation table code. It is a race condition which mostly happens on systems
with multiple cores and multiple network interface attached to batman-adv. Two
Freifunk communities which were haunted by weird crashes (with backtraces
reporting problems in other parts of the kernel) were kind enough to test this
patch. They reported that there systems are now running stable after applying
this patch.
An invalid memory access was detected in the batadv_icmp_packet_rr handling
code when receiving a skbuff with fragments. The last patch is fixing a memory
leak when the interface is removed via .dellink. The code to fix it was copied
from the code handling the legacy sysfs interface to remove netdevices from a
batman-adv netdevice.
There are still 28 patches in the development tree for v4.8 but I will leave
them to Antonio because these are cleanups and features and therefore for net-
next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The untagged vlan object is only destroyed when the interface is removed
via the legacy sysfs interface. But it also has to be destroyed when the
standard rtnl-link interface is used.
Fixes: 5d2c05b21337 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb_linearize may reallocate the skb. This makes the calculated pointer
for ethhdr invalid. But it the pointer is used later to fill in the RR
field of the batadv_icmp_packet_rr packet.
Instead re-evaluate eth_hdr after the skb_linearize+skb_cow to fix the
pointer and avoid the invalid read.
Fixes: da6b8c20a5b8 ("batman-adv: generalize batman-adv icmp packet handling")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each batadv_tt_local_entry hold a single reference to a
batadv_softif_vlan. In case a new entry cannot be added to the hash
table, the error path puts the reference, but the reference will also
now be dropped by batadv_tt_local_entry_release().
Fixes: a33d970d0b54 ("batman-adv: Fix reference counting of vlan object for tt_local_entry")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tt_req_node is added and removed from a list inside a spinlock. But the
locking is sometimes removed even when the object is still referenced and
will be used later via this reference. For example batadv_send_tt_request
can create a new tt_req_node (including add to a list) and later
re-acquires the lock to remove it from the list and to free it. But at this
time another context could have already removed this tt_req_node from the
list and freed it.
CPU#0
batadv_batman_skb_recv from net_device 0
-> batadv_iv_ogm_receive
-> batadv_iv_ogm_process
-> batadv_iv_ogm_process_per_outif
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_ogm_handler_v1
-> batadv_tt_update_orig
-> batadv_send_tt_request
-> batadv_tt_req_node_new
spin_lock(...)
allocates new tt_req_node and adds it to list
spin_unlock(...)
return tt_req_node
CPU#1
batadv_batman_skb_recv from net_device 1
-> batadv_recv_unicast_tvlv
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_unicast_handler_v1
-> batadv_handle_tt_response
spin_lock(...)
tt_req_node gets removed from list and is freed
spin_unlock(...)
CPU#0
<- returned to batadv_send_tt_request
spin_lock(...)
tt_req_node gets removed from list and is freed
MEMORY CORRUPTION/SEGFAULT/...
spin_unlock(...)
This can only be solved via reference counting to allow multiple contexts
to handle the list manipulation while making sure that only the last
context holding a reference will free the object.
Fixes: a73105b8d4c7 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Amadeus Alfa <amadeus@chemnitz.freifunk.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a VLAN tagged frame is received and the corresponding VLAN is not
configured on the soft interface, it will splat a WARN on every packet
received. This is a quite annoying behaviour for some scenarios, e.g. if
bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames
from Ethernet coming in without having any VLAN configuration on bat0.
The code should probably create vlan objects on the fly and
transparently transport these VLAN-tagged Ethernet frames, but until
this is done, at least the WARN splat should be replaced by a rate
limited output.
Fixes: 354136bcc3c4 ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have a system which uses fixed PHY devices and calls
fixed_phy_register() then fixed_phy_unregister() we can exhaust the
number of fixed PHYs available after a while, since we keep incrementing
the variable phy_fixed_addr, but we never decrement it.
This patch fixes that by converting the fixed PHY allocation to using
IDA, which takes care of the allocation/dealloaction of the PHY
addresses for us.
Fixes: a75951217472 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the 'default_permissions' mount option, ovl_permission() on
non-directories was missing a dput(alias), resulting in "BUG Dentry still
in use".
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 8d3095f4ad47 ("ovl: default permissions")
Cc: <stable@vger.kernel.org> # v4.5+
|
|
Currently we have 2 segments that are bolted for the kernel linear
mapping (ie 0xc000... addresses). This is 0 to 1TB and also the kernel
stacks. Anything accessed outside of these regions may need to be
faulted in. (In practice machines with TM always have 1T segments)
If a machine has < 2TB of memory we never fault on the kernel linear
mapping as these two segments cover all physical memory. If a machine
has > 2TB of memory, there may be structures outside of these two
segments that need to be faulted in. This faulting can occur when
running as a guest as the hypervisor may remove any SLB that's not
bolted.
When we treclaim and trecheckpoint we have a window where we need to
run with the userspace GPRs. This means that we no longer have a valid
stack pointer in r1. For this window we therefore clear MSR RI to
indicate that any exceptions taken at this point won't be able to be
handled. This means that we can't take segment misses in this RI=0
window.
In this RI=0 region, we currently access the thread_struct for the
process being context switched to or from. This thread_struct access
may cause a segment fault since it's not guaranteed to be covered by
the two bolted segment entries described above.
We've seen this with a crash when running as a guest with > 2TB of
memory on PowerVM:
Unrecoverable exception 4100 at c00000000004f138
Oops: Unrecoverable exception, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 1280 PID: 7755 Comm: kworker/1280:1 Tainted: G X 4.4.13-46-default #1
task: c000189001df4210 ti: c000189001d5c000 task.ti: c000189001d5c000
NIP: c00000000004f138 LR: 0000000010003a24 CTR: 0000000010001b20
REGS: c000189001d5f730 TRAP: 4100 Tainted: G X (4.4.13-46-default)
MSR: 8000000100001031 <SF,ME,IR,DR,LE> CR: 24000048 XER: 00000000
CFAR: c00000000004ed18 SOFTE: 0
GPR00: ffffffffc58d7b60 c000189001d5f9b0 00000000100d7d00 000000003a738288
GPR04: 0000000000002781 0000000000000006 0000000000000000 c0000d1f4d889620
GPR08: 000000000000c350 00000000000008ab 00000000000008ab 00000000100d7af0
GPR12: 00000000100d7ae8 00003ffe787e67a0 0000000000000000 0000000000000211
GPR16: 0000000010001b20 0000000000000000 0000000000800000 00003ffe787df110
GPR20: 0000000000000001 00000000100d1e10 0000000000000000 00003ffe787df050
GPR24: 0000000000000003 0000000000010000 0000000000000000 00003fffe79e2e30
GPR28: 00003fffe79e2e68 00000000003d0f00 00003ffe787e67a0 00003ffe787de680
NIP [c00000000004f138] restore_gprs+0xd0/0x16c
LR [0000000010003a24] 0x10003a24
Call Trace:
[c000189001d5f9b0] [c000189001d5f9f0] 0xc000189001d5f9f0 (unreliable)
[c000189001d5fb90] [c00000000001583c] tm_recheckpoint+0x6c/0xa0
[c000189001d5fbd0] [c000000000015c40] __switch_to+0x2c0/0x350
[c000189001d5fc30] [c0000000007e647c] __schedule+0x32c/0x9c0
[c000189001d5fcb0] [c0000000007e6b58] schedule+0x48/0xc0
[c000189001d5fce0] [c0000000000deabc] worker_thread+0x22c/0x5b0
[c000189001d5fd80] [c0000000000e7000] kthread+0x110/0x130
[c000189001d5fe30] [c000000000009538] ret_from_kernel_thread+0x5c/0xa4
Instruction dump:
7cb103a6 7cc0e3a6 7ca222a6 78a58402 38c00800 7cc62838 08860000 7cc000a6
38a00006 78c60022 7cc62838 0b060000 <e8c701a0> 7ccff120 e8270078 e8a70098
---[ end trace 602126d0a1dedd54 ]---
This fixes this by copying the required data from the thread_struct to
the stack before we clear MSR RI. Then once we clear RI, we only access
the stack, guaranteeing there's no segment miss.
We also tighten the region over which we set RI=0 on the treclaim()
path. This may have a slight performance impact since we're adding an
mtmsr instruction.
Fixes: 090b9284d725 ("powerpc/tm: Clear MSR RI in non-recoverable TM code")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Olga Kornievskaia reports that the following test fails to trigger
an OPEN_DOWNGRADE on the wire, and only triggers the final CLOSE.
fd0 = open(foo, RDRW) -- should be open on the wire for "both"
fd1 = open(foo, RDONLY) -- should be open on the wire for "read"
close(fd0) -- should trigger an open_downgrade
read(fd1)
close(fd1)
The issue is that we're missing a check for whether or not the current
state transitioned from an O_RDWR state as opposed to having transitioned
from a combination of O_RDONLY and O_WRONLY.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: cd9288ffaea4 ("NFSv4: Fix another bug in the close/open_downgrade code")
Cc: stable@vger.kernel.org # 2.6.33+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
The only users of audit_get_tty and audit_put_tty are internal to
audit, so move it out of include/linux/audit.h to kernel.h and create
a proper function rather than inlining it. This also reduces kABI
changes.
Suggested-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: line wrapped description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Move the calculations of values after the allocation in case the
allocation fails. This avoids wasting effort in the rare case that it
fails, but more importantly saves us extra logic to release the tty
ref.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Two trivial fixes - one for a bug in the allocation failure path and
the other a compiler warning fix"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: sata_mv: fix mis-conversion in mv_write_cached_reg()
ata: fix return value check in ahci_seattle_get_port_info()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
"Regression fix for multitouch palm rejection from Allen Hung"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: enable palm rejection for Windows Precision Touchpad
Revert "HID: multitouch: enable palm rejection if device implements confidence usage"
|
|
Vertical flipping is available on both Gen2 and Gen3, while horizontal
flipping is only available on Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Allow reconfiguration of the alpha value at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
We don't need to walk the pipeline when propagating the alpha value as
all the information needed for propagation is already available from the
pipeline structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Allow reconfiguration of the look-up table and processing mode at
runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Allow reconfiguration of the look-up table at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Controls are applied to the hardware in the configure operation of the
VSP entities, which is only called when starting the video stream. To
enable runtime modification of controls we need to call the configure
operations for every frame. Doing so is currently not safe, as most
parameters shouldn't be modified during streaming. Furthermore the
configure operation can sleep, preventing it from being called from the
frame completion interrupt handler for the next frame.
Fix this by adding an argument to the configure operation to tell
entities whether to perform a full configuration (as done now) or a
partial runtime configuration. In the latter case the operation will
only configure the subset of parameters related to runtime-configurable
controls, and won't be allowed to sleep when doing so.
Because partial reconfiguration can depend on parameters computed when
performing a full configuration, the core guarantees that the configure
operation will always be called with full and partial modes in that
order at stream start. Entities thus don't have to duplicate
configuration steps in the full and partial code paths.
This change affects the VSP driver core only, all entities return
immediately from the configure operation when called for a partial
runtime configuration. Entities will be modified one by one in further
commits.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The CLU processing block is a 2D/3D lookup table that converts the input
three color component data into desired three color components using a
lookup table.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Replace the custom ioctl with a V4L2 control in order to standardize the
API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The LUT mutex isn't initialized when creating the LUT, fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Freeing a fragment requires freeing DMA coherent memory, which can be
performed with interrupts disabled as per the DMA mapping API contract.
The fragments can't thus be freed synchronously when a display list is
recycled. Instead, move the fragments to a garbage list and use a work
queue to run the garbage collection.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Initialize the function field of all subdev entities instantiated by the
driver. This gets rids of multiple warnings printed by the media
controller core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The LIF is only used when feeding the VSP output to the DU. The only way
to do so is by controlling the VSP directly from the DU driver and
disabling the VSP userspace API. There is thus no need to create a LIF
entity when the userspace API is enabled, as it can't be used in that
case.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The media device doesn't need to be exposed to userspace when the VSP is
fully controlled by the DU driver. Don't register it in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check the entity pointer instead of the feature flag to see if the
entity is available before creating related links. The two methods are
currently equivalent, but will differ in the future as we implement
support for ignoring some of the entities present in the hardware.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The video statistics function describes entities such as video histogram
engines or 3A statistics engines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add composer, pixel formatter, pixel encoding converter and scaler
functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The intensity control reused the V4L2_CID_CONTRAST control ID by
mistake. Fix it by using an ID from the device-specific IDs range.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The device is stopped when STREAMOFF is called on the last video node in
the pipeline. This results in possible memory corruption and/or crashes,
as userspace could free buffers while the hardware is still writing to
them, and the frame completion interrupt handler could try to access
buffers that don't exist anymore.
Fix this by stopping the pipeline upon the first STREAMOFF call, not the
last.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The structures are never modified, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The vsp1_pipeline wq field is a wait queue, not a work queue. Fix the
comment accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
